Hi,
I have a galaxy skyrocket i727 from AT&T with last Gingerbread firmware(2.3.6 from at&t).Now i am in india.Recently i did a factory reset and now i have lost data connectivity(though i get full signal and can do calls or messages).
Even before i used to select frequency bands manually to swap between 2g-3g by dialling *#*#197328640#*#* and i used to get data fine.As there is no such option of selecting 'gsm only' or "wcdma preffered/gsm" in wireless&networks menu of the AT&T Firmware.
So the main question is if i put the unofficial ICS ROM like AOKP or UCALC4 than will i get this 2G to 3G selection in settings?Will the phone select indian frequency bands automatically?
thanks!
You may have lost your apn and that's why you can't get data, check under settings mobile network apn if there is anything there(I think that's how it goes in GB) if there isn't check your provider's site or call them and ask how you should configure it.
About your second question, it depends on what rom you will flash, some support it and some don't.
kishke said:
You may have lost your apn and that's why you can't get data, check under settings mobile network apn if there is anything there(I think that's how it goes in GB) if there isn't check your provider's site or call them and ask how you should configure it.
About your second question, it depends on what rom you will flash, some support it and some don't.
Click to expand...
Click to collapse
Thanks for replying!
My APN is ok.I requested new apn after deleting older ones and even did a manual "Add new apn" perfectly.Thats why i am asking this question ,because there is no reason for getting "no data".Everything is perfect except that there is no "E" or "H" symbol with up-down arrows beside the network strength bars!
Stupid question but did you enable data?
kishke said:
Stupid question but did you enable data?
Click to expand...
Click to collapse
yeah dude!Obviously!
enabled - disabled it several times!rebooted after selecting apn etc etc But no good
Well sometimes we ignore the obvious so I had to ask. Check your apn again to be sure, make sure the internet apn and not mms apn is checked if you have 2, and it's defined as internet or internet+mms in case of one combined apn.
If this wont fix it something must have happened in the factory reset and you should try upgrading to ICS and see if it still works.
Hey.. BTW I have a question for you , how did you unlock your phone yo use it in India ? I know there are unlock codes, just curious if you got it from at&t or you had to go the eBay way ?
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
gravi2 said:
Hey.. BTW I have a question for you , how did you unlock your phone yo use it in India ? I know there are unlock codes, just curious if you got it from at&t or you had to go the eBay way ?
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
Click to expand...
Click to collapse
unlocked via z3x box....a tool used by unlockers.Had a friend of mine who owned it.It unlocks all samsungs for free!!
- You need to be SIM Unlocked and have a RAT Unlocked Radio (HINT: Roger I-727R radios)
and
- You need a ROM to support those, if you using TouchWiz I have supported this always from the beg. im my
ROM (see my sig.)
And I do travel there once a quarter, no issues for me. I have an IDEA Card and it works perfect, even ROAMING to 3G where IDEA piggy backs on other providers..
mohan_kr said:
- You need to be SIM Unlocked and have a RAT Unlocked Radio (HINT: Roger I-727R radios)
and
- You need a ROM to support those, if you using TouchWiz I have supported this always from the beg. im my
ROM (see my sig.)
And I do travel there once a quarter, no issues for me. I have an IDEA Card and it works perfect, even ROAMING to 3G where IDEA piggy backs on other providers..
Click to expand...
Click to collapse
when i initially read your name ,i guessed you were indian!
Thanks for the reply.I just flashed the sk8erwitskil,s Latest Cyanogenmod 9 with UCLF6 libs just to check if i was able to switch radios,but right now i am in "2G/gsm only" area.Data is working fine,but cannot turn on wifi...it keeps saying "turning on".
My phone is sure sim-unlocked on idea network,and on UCLF6 Modem(is this thing same as a "radio"?).Initially i was on stock at&t GB firmware.Btw ,which place in india do u travel?
If wifi error persists i will flash EMBRYO Rom
Related
Hello, I think my phone is simlocked. I bought my nexus s from carphonewarhouse here in the UK on vodafone contract.
My vodafone simcard works fine but if I put another carrier simcard in, it says no service but I have full/good reception. Also it does not ask for a simlock unlock code!
WHen I manually choose the network it says, unable to connect to the network.
I have changed roms etc.. to stock and even tried 2.3.2 radio and the 2 new 2.3.3 radios!
Please help? I thought all nexus s works with any network?
all Nexus comes sim unlocked
if you try another network, make sure it has the correct frequencies supported
Did you try radios meant for the other carrier's network?
Sent from my SCH-I500 using XDA App
dangerismymiddlename.com said:
Did you try radios meant for the other carrier's network?
Sent from my SCH-I500 using XDA App
Click to expand...
Click to collapse
I couldn't find them, do u know where I can get it from? I tried all network Sims in the UK, none work except vodafone.
You probably have manually selected Vodafone in the past and the phone tries to connect to Vodafone. You have to go into settings and select 'automatic network selection' or manually select another network.
Am I the only one stoked by the timestamp on the op <.< 1337
Sent from my MattedBlues CM7 Nexus S from the XDA Premium app.
georgemv said:
You probably have manually selected Vodafone in the past and the phone tries to connect to Vodafone. You have to go into settings and select 'automatic network selection' or manually select another network.
Click to expand...
Click to collapse
I've tried that, it says "cannot connect to the network"
Check your APN settings (Settings, Wirelss & network, mobile networks, APN).
You might have success by manually adding the correct ones for the network you're attempting to connect to.
Are you inserting ACTIVATED SIM cards? Also does making voice calls work on it? If voice works and data doesn't, it's your APN settings that need adjustments.
-Nexus S
I've searched and can't find a thread with stuff helpful to me. I would like a radio that will allow me to use 2G network. I live in rural Alaska and we have some crappy networks. I know it would probably work with factory settings, but I'd like to keep my phones custom rom Honeysense 6.2.2. I have been trying to make it work on the apn settings given to me by my provider but haven't succeeded. If someone out there has a solution please help.
72aiden said:
I've searched and can't find a thread with stuff helpful to me. I would like a radio that will allow me to use 2G network. I live in rural Alaska and we have some crappy networks. I know it would probably work with factory settings, but I'd like to keep my phones custom rom Honeysense 6.2.2. I have been trying to make it work on the apn settings given to me by my provider but haven't succeeded. If someone out there has a solution please help.
Click to expand...
Click to collapse
You can use an app from the market to do it once you are rooted
72aiden said:
I've searched and can't find a thread with stuff helpful to me. I would like a radio that will allow me to use 2G network. I live in rural Alaska and we have some crappy networks. I know it would probably work with factory settings, but I'd like to keep my phones custom rom Honeysense 6.2.2. I have been trying to make it work on the apn settings given to me by my provider but haven't succeeded. If someone out there has a solution please help.
Click to expand...
Click to collapse
Use Network. Towards the bottom, change the option to GSM Only.
1. "Sorry to ask but Radio help please" <-- Don't be sorry to ask. No one is going to flame u if ur efforts were genuine in searching first.
2. For ur question:
a. [User input] Go to wireless settings, and select 2G network
[System Action] This will turn off data, and re-enable it, but high chances (for me, its "always") still be on 3G/H
b. [User input] Go to network selection mode, and select manual
[System Action]This will present u with a list of networks to select (only one if u r on AT&T)
c. [User input] Select the network (AT&T if u r on AT&T)
This should now put the phone on 2G/EDGE network.
Warning: Since u r forcing this, there could be some patches (like when on certain areas when on road, etc) where u cud face loss of signal.
Simba501 said:
Use Network. Towards the bottom, change the option to GSM Only.
Click to expand...
Click to collapse
Using this app (this app is just a shortcut to the options in *#*#4636#*#*) many a times caused me a Phone process FC in an infinite loop (most recent one was y'day). The FC loop sometimes wasn't instantaneous, and started after ending a call and when the phone tried to get back to EDGE network.
Only way out was restoring from my previous nandroid backup. So I would be cautions.
I recently installed the JellyBean ROM for my A2 and changed few settings in the power manager after which I am unable to get 4G connectivity. I always see Edge in the status bar. I've tried re-trace my steps in the power manager but havent been able to turn on 4G yet.
Any guidance on how I could get my 4G back ?
----- UPDATE ----
I had to flash the same ROM again onto my phone and now its functioning properly. Still don't know the root cause but will report again if I see it happen again.
Thanks
Dhanvi
kapiladhanvi said:
I recently installed the JellyBean ROM for my A2 and changed few settings in the power manager after which I am unable to get 4G connectivity. I always see Edge in the status bar. I've tried re-trace my steps in the power manager but havent been able to turn on 4G yet.
Any guidance on how I could get my 4G back ?
Thanks
Dhanvi
Click to expand...
Click to collapse
Which JellyBean ROM? Please remember to be very specific as to the conditions surrounding the problem you're having!
I'd first try to go into Settings/ Below Data Usage tap 'More...'/ Mobile Networks
and make sure that 'Use only 2G networks' isn't checked.
Also, which carrier are you on? (I know most are on AT&T, but I'm on Straight Talk so I ask)
Alperon said:
Which JellyBean ROM? Please remember to be very specific as to the conditions surrounding the problem you're having!
I'd first try to go into Settings/ Below Data Usage tap 'More...'/ Mobile Networks
and make sure that 'Use only 2G networks' isn't checked.
Also, which carrier are you on? (I know most are on AT&T, but I'm on Straight Talk so I ask)
Click to expand...
Click to collapse
Thanks for your reply. I'm on the "MagicMod-Jellybean-Experimental" Atrix ROM on ATT.
The "Always use 2G" is unchecked which means that it should use 4G when available. Which bought me to the next section where I could search for network providers. When I searched for networks, most of the times my phone fails to find ATT in the list of available networks. I do have 4 bars on my phone though. I dont see the network provider name in the status bar so I dont know where it is connected currently.
My current hypothesis is that my phone is unable to connect/register to the ATT network and so I dont get 4G speeds.
Does that make sense?
Dhanvi
kapiladhanvi said:
Thanks for your reply. I'm on the "MagicMod-Jellybean-Experimental" Atrix ROM on ATT.
The "Always use 2G" is unchecked which means that it should use 4G when available. Which bought me to the next section where I could search for network providers. When I searched for networks, most of the times my phone fails to find ATT in the list of available networks. I do have 4 bars on my phone though. I dont see the network provider name in the status bar so I dont know where it is connected currently.
My current hypothesis is that my phone is unable to connect/register to the ATT network and so I dont get 4G speeds.
Does that make sense?
Dhanvi
Click to expand...
Click to collapse
Just so you know A small H by your signal bar means 4g. I am on AT&T and all I have to do is uncheck those boxes and reboot and data and MMS works fine
From my locked down superchargedV6 1.425ghz A "What tha duce?"
daavvis said:
Just so you know A small H by your signal bar means 4g. I am on AT&T and all I have to do is uncheck those boxes and reboot and data and MMS works fine
From my locked down superchargedV6 1.425ghz A "What tha duce?"
Click to expand...
Click to collapse
Yep. I'm aware that a H is 4G. I see an 'E' next to the signal bar. I did have an 'H' right after I installed my ROM but since today I'm only seeing 'E' .
I'll try flashing the CM10 ROM and check if that fixes my issue. If not, I'll copy over an apns-config.xml from an ICS install and replace my current one with that just in case.
try changing network mode by an awesome app called "Network" by phillip
in market .... it is simple & best option
shardul.phatak said:
try changing network mode by an awesome app called "Network" by phillip
in market .... it is simple & best option
Click to expand...
Click to collapse
Thanks for the tip. I'll try that. Looks like a reflash (of the same ROM) solved the problem for me though. Its back to 'H' for me. I still haven't tried to flash CM10.
Thanks for your help guys.
Hello there, i just got this phone 3 weeks ago and since i have wifi i didnt test the 3g conection before. i activated a data pack and i just realized that my 3g doesnt come on at all. the screen shows 4g left side of the signal strengh but it doesnt work at all. i got at&t version. i confirmed with my carrier and i did activate data, they even helped me to set up the apn but is still not working. can you helpe me? thanks!
PD: they said they couldnt have done more because they dont support that type of device
Does it say 4G or 4G LTE? The at&t icons are a bit different I'd you're not used to them.
4G = hspa
4G LTE = LTE
So if you're getting the 4G icon you are actually getting 3G hspa speeds.
Sent from my Evita
If another carrier besides AT&T, you will need to find the APN settings for your carrier and manually enter it into Settings>Mobile network settings>Access point names. Select "New APN" and enter the correct settings for your manufacturer.
The 4G icon simply means a network is present, it doesn't mean you are connected to it.
thank you for helping people. whel actualy i wouldnt mind getting 3g network access, the point is that i dont have internet access at all. i called my carrier (Claro - El salvador) and they helped me to set up the apt but is still not working. i was wondering if there is something else i could try to fix this
nevermind, i finally fixed it
Please share the fix so the information is available for anyone who might have the same problem in the future.
Sent from my Evita
Please share the fix so the information is available for anyone who might have the same problem in the future.
Click to expand...
Click to collapse
sorry. well, first i did master reset, once done i set up an apn (carrier provides you with this info), then went to mobile network > network operators > select automatically. once the device found the "CLARO" network i turned data on and got internet service.
Thankyou, these threads live on long after we're finished with them so it's important to have the information readily available for future troubleshooters.
Sent from my Evita
tolonuia said:
sorry. well, first i did master reset, once done i set up an apn (carrier provides you with this info), then went to mobile network > network operators > select automatically. once the device found the "CLARO" network i turned data on and got internet service.
Click to expand...
Click to collapse
I'm guessing you either had not entered the APN info exactly correctly the first time. Or also, after entering the APN you actually have to select it as the "active" one on the list of APNs (making sure it has the colored dot next to it). Maybe it did need a factory reset, but this shouldn't be necessary just to change APN.
Happy you got it figured out.
I bought an Unlocked Canadian S6 recently, and it just won't let me connect to the LTE network.
Model Numer : SM-G920W8
Android Version : 5.0.2
Baseband : G920W8VLU1AOCG
Connecting to the LTE is not even an option. When I go in the Network Options, I get the choice between :
-WDCMA/GSM (auto connect)
- WDCMA only
- GSM only
I know for a fact that I am in the coverage zone, so no need to ask that silly question
I've tried different SIM cards, played in the options a bit, and factory reset the phone about 5 times now, yet nothing seems to work.
Also, when I try to do the update, it just reboots and gives me an Android logo and a failed Icon
I've only seen one other post like this from a carrier's support website, but no solutions were found.
**Update : For a reason, after a recovery, it will connect to the LTE for a bit or until next boot, then go back to what it is now.
First question, who did you buy the phone from? Second, Is it second hand? By default, Wind mobile does not allow the LTE option to be displayed in system settings as they as a carrier don't have LTE. It is blocked by the CSC setting for the carrier. As for other carriers It should leave you the option to connect in settings where you say it is not. If it is a Wind phone, You would need to change the CSC to enable the LTE selection. There is a method to force LTE even without option in settings, but I think it is removed in the latest firmware. Try dialing *#2263# in the dialer. It may bring you to menu that will allow you to select LTE. This is not a permanent method though as it will need to be done every boot. The other way, (If you are in fact a Wind/Mobilicity phone) is to enter dialer and enter *#272*IMEI# with IMEI being your devices unique code. If at all possible, take a full nand and Titanium Backup before doing this and be sure to transfer everything off the phone to a PC. This method wipes everything and I mean everything off the phone buy is a surefire way to enable LTE.
Yes, it was second hand. I didn't ask who was his carrier simply because it was unlocked.
I'll try it tomorrow, thanks for the information
Here is the menu you will see when you type the *#272*imei# code into your dialer. The codes are the carrier names. Mine which is GLW is Wind, BMC is Bell, RWC is Rogers, etc.
Maybe there is no LTE in your area...
roydok said:
Maybe there is no LTE in your area...
Click to expand...
Click to collapse
It would still be visible in the Settings/Mobile Networks/Network Mode menu which it is not. His problem is more than that.
BCSC said:
First question, who did you buy the phone from? Second, Is it second hand? By default, Wind mobile does not allow the LTE option to be displayed in system settings as they as a carrier don't have LTE. It is blocked by the CSC setting for the carrier. As for other carriers It should leave you the option to connect in settings where you say it is not. If it is a Wind phone, You would need to change the CSC to enable the LTE selection. There is a method to force LTE even without option in settings, but I think it is removed in the latest firmware. Try dialing *#2263# in the dialer. It may bring you to menu that will allow you to select LTE. This is not a permanent method though as it will need to be done every boot. The other way, (If you are in fact a Wind/Mobilicity phone) is to enter dialer and enter *#272*IMEI# with IMEI being your devices unique code. If at all possible, take a full nand and Titanium Backup before doing this and be sure to transfer everything off the phone to a PC. This method wipes everything and I mean everything off the phone buy is a surefire way to enable LTE.
Click to expand...
Click to collapse
Sweet! It works :good: Thanks man
Now, would you have any ideas on why the update won't work? I didn't get much into it yet, but I will soon.
I'm not sure why it wouldn't update, but now that you have changed the CSC you can download the update and flash with Odin. Pick your carrier and go to town. The guy running the following thread runs his own firmware host. He's got amazing DL speeds. Usually takes me 6 or so minutes to do the 1.6gb file. http://forum.xda-developers.com/showthread.php?t=3086387
I'm having the same issue.
Scurbs said:
Sweet! It works :good: Thanks man
Now, would you have any ideas on why the update won't work? I didn't get much into it yet, but I will soon.
Click to expand...
Click to collapse
Connected with someone selling a G920W8 version. LTE is disabled and the codes aren't working. Can you reaffirm which unlock code worked for you? I'm on Fido, what LTE network are you using?
hi BCSC
Thanks for the details. I searched complete net and read all articles but nothing set me up with the proper thing. i read your solution i dialled *#2263# and all i got is service mode and in that i went to band selection , LTE and the all ....... Yes and its showing LTE in mobile data. THanks so much.
But now another issue, network is showing perfect but no outgoing and incoming calls.
in incoming its showing busy and on outgoing its not connecting to another phone.
And, Lte is not showing in mobile networks, There only 3 options still are showing.
Mine is same Wind S6 but i had to use in India.
Let Me know
Thanks once again
Cheeerzzzzz
Varun
Picking LTE from the service mode will note make it visible from the settings menu. Its more of a workarpund instead of a way of permanently enabling it. As for the issue of no out/in calls, my best guess is that it could be due to which LTE bands are being used or are available in India. Unfortunatly I have no way to test that option. I only was successful in getting the Wind LTE option on Canadian carriers.
Sent from my SM-G935W8 using XDA-Developers mobile app