my tablet is stuck on the home locked screen and from looking around on the net and the person i got the tablet from didnt give me the sd card and when i hold the power and volume up down the android guy with red sign and the exclamation point over his chest comes up and was told i need to download the software i need to an sd card..
if anybody could help thanks or steer me i the right direction.
MOD EDIT: REMOVED EMAIL
Related
hi all
i got a magician from a friend to play with but when i got it i only saw it starting up and then by align screen it would boot further
ive went to the wiki and checked ive i could find the combo for hard reseting this phone(whitout succes) i managed to find how to get in bootloader so i checked it
when i go in the bootloader my screen doesnt light on(is this normal because my other devices do this)
further it says v1.02 on the bottom of the screen
now ive tried to insatl the dutch t mobile rom from the wiki but i get a connection error
now ive seen that updating this phone doesnt go like on a blackstone\rhodium and it has something to do with a sd card in it?
i have the gap for sd card but not one in it(is this nessacary?)
after the connection errors i cant even see the align screen anymore it goes straight to bootloader when i press only the on button and getting out the battery for a minute and put it back in also brings me to the boortloader when i press the power button:S (now its working and i can get to align screen again:S)
can someone please help me fix this phone
best regards mini
You have Rome. You need from T-Mobils Rome:
- ms_. nbf
- nk.nbf
- radio_. nbf
All that in the folder suspended below copy. The device in the boat mode bring (On top the left and right key + power) Then you are able to do him flashen.
thanks for the reply
got a exe file to use but going to try to extract it when im home and hope i get those files from it
stil not working
tried it a couple of times but i always get this message
btw in bootloader it says v1.02 on the bottom
and strating in bootloader doesnt work at all for updating because the program doesnt see the phone:S
i have to get it started up to the point of align screen then connect it to comp with activesync
then i got those screens
when i start the phone i see the next things on the phone in spalsh screen
r1.12.00
g1337.42
d1.12.00
i dont have a memorycard in it dont know ive thats nessacary
best regards miniterror
one more with the back sticker so it really is a magician
If is a Magician. The mistake 101 means which does not fit the ID. What you can still try to protect your Rome and more than 416 bits, a Big Storage Rome to flashen. You can make this everything about memory map. You find instructions here.
ok i dont get it at all so i'll throw away the phone
thanks anyway for trying to help me
Hi everyone. I am hoping that you will be able to help me because I am not getting any joy from the seller of my tablet. (Letsgomobile Hong Kong)
I am wanting to install the windows drivers for my Zenithink ZT-180 but having problems.
I am holding the round menu button down whilst I power up the Tablet and it shows a small android icon with a triangle containing an '!' inside the triangle on the screen of the tablet and if I press the menu button again it comes up with Android e2 and a mini menu which includes
Reboot
SD card update
clear Cache
and reset to factory settings
But when I plug it into my computer it detects device and is identifying it as Android Eclair.. and it wont accept the drivers included in Burntool 7.2..
looking at the guides on the net it appears that the device should be identifying its self as SEC SOC Test Board..!
Note I have tried several computers running xp,vista and win 7 and all do the same thing
Can anyone advise where I am going wrong? or is it that the tablet is faulty?
if you need any more info let me know
Many thanks in advance
Ken
please someone help me out I feel like I'm fishing aroud in the dark here as android is new to me despite being a Boffin with windows. Sorry I know I haven't posted here before but I have been a member for 4 years.
USB Driver
Hi,
I had to update my ZT180 yesterday because it suddenly did not want to switch on aymore.
I had trouble getting my XP pc to recognise it and finally worked when I used a mini USB cable in the OTG port on the ZT. You have to make sure you are realy pressing the front button before you switch on, and then you will only see the blue light - nothing on the screen.
I tried with a mini USB adapter on a regular USB cable but it did not work. The proper cable came with my Nokia phone.
Here is a link to a good description of the process and a picture of the cable. ...dreambeta.com/support/zenithink-zt-180
Hi thanks for the advice but I am pressing the correct buttons but can't get the blue light to turn from green and instead it comes up on the screen with a triangle a small android and an "!" in the triangle???? pressing the home (round) button brings up a menu...I dont seem to be able to stop it booting into android can it be that the device has been locked????
Hey guys, I recently bricked my tablet by fiddling around with the "format SD card" option in the settings menu. I thought I was formatting a secondary SD (which I later found out wasn't even installed) and it looks like I formatted the system SD card instead. The thing now hangs at a black screen with "A N D R O I D _" displayed at the top left hand corner.
Here is the tablet itself:
http://www.cectunlocked.com/9.7-Inc...2-WiFi-Android-Market-Camera-800MHz-Apad.html
Scroll down a bit to see all the system specs.
Could anyone point me in the right direction to find a proper ROM and flash utility for this tablet. There seem to be so many clones out there and it's a bit overwhelming. Not sure which one is which. Any help at all would be greatly appreciated. Thanks.
Ok, how about recovery mode? I've tried powering on with the power+home buttons held down, but nothing.
I have a Coby Kyros 7127, I cannot get it to get past the android cycle of the startup. Once the power on button is depressed, Coby appears, then it goes to android and that is where it stays... it cycles and does not go past that stage. I can depress the reset button and it resets. I can also depress the power button and sound button and it will stay on Coby, however in the bottom left corner, in blue, it says "The Device Enter Fastboot Mode, Please Connect USB To PC or Reset The Device, Waitting......."
I have watched many of the videos and cannot figure this out, I have tried many of the things online - the issue is, I cannot get the tablet to get far enough along in the boot sequence for my computer to display the tablet and run adb. This tablet is for my grandaughter and we were hoping to have it for her to use.
We would like to make it work like many of the videos state... any help is appreciated.
Were in the same boat. Here's some tips...
melw25 said:
I have a Coby Kyros 7127, I cannot get it to get past the android cycle of the startup. Once the power on button is depressed, Coby appears, then it goes to android and that is where it stays... it cycles and does not go past that stage. I can depress the reset button and it resets. I can also depress the power button and sound button and it will stay on Coby, however in the bottom left corner, in blue, it says "The Device Enter Fastboot Mode, Please Connect USB To PC or Reset The Device, Waitting......."
I have watched many of the videos and cannot figure this out, I have tried many of the things online - the issue is, I cannot get the tablet to get far enough along in the boot sequence for my computer to display the tablet and run adb. This tablet is for my grandaughter and we were hoping to have it for her to use.
We would like to make it work like many of the videos state... any help is appreciated.
Click to expand...
Click to collapse
I am in the same boat! If you download ClockWorkMod from here on xda which you can do on this forum its the 2nd post from a guy named "the_kwa" you can save CWM on your SD card and use ADB commands to boot to into CWM. Once there you can try to do a factory reset. If that doesn't work, then you have gotten to where I am.
In short, you need to find a custom ROM for the tablet. I have scoured the interwebs trying to find one and the only place that seems to have them is a site called: Kyros Tablet Zone or KTZ. Now, if you are willing to pay $12 for a ROM from them, then your done. Tablet will be back up and running & your good.
My MID7127 is dead too. If you do decide to purchase a ROM from KTZ let me know and I'll talk you through how to install it step by step. If your willing to maybe share that rom with me and get mine going again! Let me know. bacause I was about to post this same issue until I found your post.
Either way let me know & hit the thanks button if that helped you out.
so my friend got his kid a tablet for Xmas its a Maylong M270 and his youngest got ahold of it and put a pattern lock on the tablet lol but anyways im trying to access the bootloader this tablet come with a keyboard and has no other buttons on it but a power button im hoping the bootloader is unlocked and i can do a reset there but how do i access it usually it like volume down and power or some but theres no buttons lol im frustrated anyone got any ideas...
gangs aggatn
tmathews1988 said:
so my friend got his kid a tablet for Xmas its a Maylong M270 and his youngest got ahold of it and put a pattern lock on the tablet lol but anyways im trying to access the bootloader this tablet come with a keyboard and has no other buttons on it but a power button im hoping the bootloader is unlocked and i can do a reset there but how do i access it usually it like volume down and power or some but theres no buttons lol im frustrated anyone got any ideas...
Click to expand...
Click to collapse
ugg...
tmathews1988 said:
ugg...
Click to expand...
Click to collapse
Don't bump your own thread please. Read the rules of XDA as you obviously need to do so.
Have you tried unlocking it through the gmail account?
they did not setup a gmail account on the device they only had it for a few hours at this point and the makers Maylong are providing 0 support
How to factory reset the Maylong m270
1. get firmware here
http://www.maylonggroup.com/Tablets/M270CQ1/M-270CQ_Ver 1.5.6.zip
2. Unzip and copy contents of folder to a clean sdcard
3. insert sdcard into the tablet and power on.
4. Wait until screen says 100% and tells you to remove media.
5. enjoy!!
tmathews1988 said:
they did not setup a gmail account on the device they only had it for a few hours at this point and the makers Maylong are providing 0 support
Click to expand...
Click to collapse
That download only gets to about 10% and fails. Does anyone happen to have a copy of this firmware. Ive tried numerous ones but the touch screen doesnt work. I had the same pin-lock problem and the screen worked before