Database Info

Stuck at screen adjusting!! (Broken screen on p3600)

Hi i recently got this htc p3600 with broken touchscreen, the lcd is fine but the touchscreen have some cracks in it.
I don't know anything about what versions of roms etc is in it. All i know is that windows mobile's in it.
When i start up the phone i get a green windows mobile screen witch says that i should click anywhere on the screen to calibrate the screen. I do htat because i can't do anything else and then this X shows up and i am suopposed to click on it in order to calibrate the screen.
I'm doing this, first in the middle then it moves to each corner but when i clicked all the corners i goes back to the middle nad starts over agaiN!!
I've clinged this stupid X for like 15 minutes now but nothing seems to happen!! Whats the problem? Can it be locked to the sim-card i've inserted??? Please help me!

guess you will have to replace the digitizer.othewise, you may try connect it with active sync and delete the call program from auto run - hopefully theres some default cal data in it.

Don't really understand what you're saying, im new to this phone and i got i broken. ALready ordered a digitizer but i want to test it out now. Tried to add a calibration value to the registry but i cant do anything because its locked.
So i think enableing rapi will o the trick but i cant start the phone to start the enable rapi program :/:/
Is there any other way to bypass this screen? Like killing the process with some taskmanager??

go search for remotecalibration.exe

How do you bypass first setup/screen alignment?

I've got a MDA which has a broken lcd. Its just cracked slightly, but still displays fine. I did a Clear Storage and now the phone has reset and is giving me the "tap here to set up your device" wizard. I need to bypass this and any screen alignment that may come up since the LCD touch feature no longer works. I've done it before when I got the phone, but I cant find the thread nor remember the steps.
Any help is appreciated.

you really can't. i heard theres a way you can flash a rom where the config has already been done, but i don't remember where i saw it

fzzyrn said:
you really can't. i heard theres a way you can flash a rom where the config has already been done, but i don't remember where i saw it
Click to expand...
Click to collapse
create a file on the root of your storage card called welcome.not

TylerC161 said:
I've got a MDA which has a broken lcd. Its just cracked slightly, but still displays fine. I did a Clear Storage and now the phone has reset and is giving me the "tap here to set up your device" wizard. I need to bypass this and any screen alignment that may come up since the LCD touch feature no longer works. I've done it before when I got the phone, but I cant find the thread nor remember the steps.
Any help is appreciated.
Click to expand...
Click to collapse
I believe this should help you.
http://www.freewarepocketpc.net/ppc-download-my-mobiler-v1-2.html
At least I hope it does.

Just create a file named WELCOME.NOT on your storage card and do a hard reset.

HI , I had this problem with all my old crashed PPC ,,, so delete this file and reboot ,,, /Windows/Startup/Welcome.exe
U can use the "Activesynce Explorer to browse the Windows Directory
Enjoy..........

use "Remote screen alignment" tool and bypass your start screen easily. search this tool in forum. you will get it easily..
Regards

welcome.not and http://www.freewarepocketpc.net/ppc-...iler-v1-2.html
THANK YOU SO MUCH kfletch and le_cactus. I'm not sure which of these worked since I did both but the welcome screen FINALLY went away. it took a while. i had to install the Mobiler software and I had problems getting my ActiveSync up but I created the welcome file by going to the desktop of my pc, right click, new , text document, i changed the default name "New Text Document.txt to Welcome.not" then I right clicked to copy it. Next---Once the Microsoft Activesync came up, I clicked on Explore --> My Windows Based Device ---> Storage Card then I selected paste to paste the welcome.not file. After this it gets a little tricky because your device has to sync again to filter the file back down to the phone. This took a while. Then after a few resets, the Mobiler software finally read 'connected', then it gives you a screen shot of your mobile device, i did a soft reset a few MORE times and it worked. It's not as cut and dry as previous posts made it sound. it's a pain in the butt.
My touch screen (T-Mobile Wing) stopped working after I used it in the bathroom while in the bathtub (I don't know what the heck I was thinking), well later that day the screen stopped working and the genius at tech support had me do a hard reset and software upgrade, which did NOT help. (whatever you do, don't call tech support, especially if the white dot beneath the battery is another color---you're screwed!!!)--AFTER tech support messes up your phone they won't bother to help you if they think it's due to water damage! I'm going to see if I can locate the forum regarding reloading the touch screen drivers. I think that may be the problem.

thanks dear I try i350 gSMART and working.

how do you select "YES" when mymobiler tries to install on the phone?
my screen is also broken, and i bypassed the welcome screen, but when i tried to install mymobiler, i cannot let the phone install remote.exe
any help?

this is ur answer
go to this its my room iam build it and not have align screen
http://forum.xda-developers.com/showthread.php?t=546422

Thanks a lot folks from XDA! I had screen broked and this works just fine! Cingular 8125 WM5. tks

ah_hin said:
how do you select "YES" when mymobiler tries to install on the phone?
my screen is also broken, and i bypassed the welcome screen, but when i tried to install mymobiler, i cannot let the phone install remote.exe
any help?
Click to expand...
Click to collapse
Buy a not broken screen

HTC TYTN(Hermes 200)
Hi there i have an HTC TYTN, happens that i'm suposed to have the same problem (maybe broken screen).
The phone was working fine untill today.
I can't bypass the screen alignment; i tryed both ways.
What can i be doing wrong?
Thanks in advance.

Bypassing with "logic"
Hi there;
In my case; i found a way to bypass it.
My screen has a 4mm scratch in the top left of the screen.
so i just pressed the bottom of the cursor (NOT IN THE MIDDLE WHERE IT'S SUPPOSED TO PRESS - "in the top left cursor" - where the scratch is)
after that i could use my phone again.
Also after this try finding the correct registry screen alignment and save it.
It will work properly.

welcome.not works for TyTN II with unresponsive touch screen . Blank micro SD card with just one blank file welcome.not. You can insert the sd card just before you hard reset

It worked in OMNIA II and passed the screen calibration..Thanks a lot guys!!!

stuck on loading splash screen

Hi, first let me say im sorry if this has already been covered somewhere, i have spent all day searching the wiki and forum to no avail. If the solution is already here please point me in the direction and delete this thread.
I have just flashed my kaiser from the original vodafone WM6 ROM to Dutty's WM6.1 Hybrid v2 5.2.19716/5.2.19700. At first everything seemed fine, then when i tried to restore the backup id created with sprite backup it restored, reset and now wont get past the loading screen. It shows the vodafone splash screen then duttys htc screen then goes back to vodafone.
I used Hardspl 3.29 before flashing. I tried hard reseting which made no difference. i cant get into the bootloader (tried the camera, power reset thing loads) and i cant connect to my pc as it wont go past the splash screen.
I had a look at MTTY but it doesnt give the options described in the instructions and after reading the warnings about MTTY decided i shouldnt mess around with what i dont understand.
Any help will be greatly apreciated, i love my phone and the idea that ive just broken it scares the crap out of me.
Thanks
Sandy

sandyfsx said:
Hi, first let me say im sorry if this has already been covered somewhere, i have spent all day searching the wiki and forum to no avail. If the solution is already here please point me in the direction and delete this thread.
I have just flashed my kaiser from the original vodafone WM6 ROM to Dutty's WM6.1 Hybrid v2 5.2.19716/5.2.19700. At first everything seemed fine, then when i tried to restore the backup id created with sprite backup it restored, reset and now wont get past the loading screen. It shows the vodafone splash screen then duttys htc screen then goes back to vodafone.
I used Hardspl 3.29 before flashing. I tried hard reseting which made no difference. i cant get into the bootloader (tried the camera, power reset thing loads) and i cant connect to my pc as it wont go past the splash screen.
I had a look at MTTY but it doesnt give the options described in the instructions and after reading the warnings about MTTY decided i shouldnt mess around with what i dont understand.
Any help will be greatly apreciated, i love my phone and the idea that ive just broken it scares the crap out of me.
Thanks
Sandy
Click to expand...
Click to collapse
first, are you SURE you can't get into bootloader?
I know it sounds stupid, but try REALLY pushing the camera button in while pushing the stylus into the reset hole. Once you get to the bootloader (tri-color screen), try flashing a different ROM
good luck

mbarvian said:
first, are you SURE you can't get into bootloader?
I know it sounds stupid, but try REALLY pushing the camera button in while pushing the stylus into the reset hole. Once you get to the bootloader (tri-color screen), try flashing a different ROM
good luck
Click to expand...
Click to collapse
I agree here a lot of people don't realize the Camera button is a two stage button. It stops at Half-Press then you can push again to get Full Press. You need a Full Press to get into bootloader.

Just to clarify.
Press and hold the camera button and at the same time insert stylus in reset hole and hold until bootloader comes up.
In other words, do not let up until bootloader shows. It should take around 2-3 seconds.

yea ive been doing that. After trying many times i have found that holding the camera button down for around 2 minutes after the htc dutty series screen comes up brings up a white screen with the error message;
"the device is unable to boot either because you have turned off the device incorrectly or tried to install an application from an untrusted source. press send to reset or any other key to cancel"
The message dissapears if i let go of the camera button, and resets back to the vodafone screen and stays there. If i press the send button same thing happens (just an idiot check but the send button is the green pick up button right?) ive tryed the enter button and both soft keys but all to the same result. I have tried holding down each button on that screen as well and the error message stays as long as i hold the button but when i let go it just goes back to the vodafone splash screen and stays there.
I have tried holding the stylus with the camera button all the way through to this error message, doesnt seem to make a difference.
just to clarify, ive done what you suggest and still cant get into the bootloader.
Thanks for any help, this is driving me mad.

hold the camera button and use the stylus to press the reset button, and continue holding the camera button until the bootloader screen pops up.
i used to let go the camera button as soon as the screen go black, but then it just reset the device instead of going into the bootloader...

oh forgot to mention. Shotly after the dutty series screen comes up i get the window appearing sound but nothing comes on screen. suggests to me that maybe its trying to tell me whatswrong but i can see what it is. maybe, i dunno..

theclueless said:
hold the camera button and use the stylus to press the reset button, and continue holding the camera button until the bootloader screen pops up.
i used to let go the camera button as soon as the screen go black, but then it just reset the device instead of going into the bootloader...
Click to expand...
Click to collapse
Im holding the camera button for around 2 minutes before it does anything, then i get the above error message.

Do you have a storage card installed?

yes. tried taking it out and doing the same thing. no different.
anything else i could try?

sandyfsx said:
Im holding the camera button for around 2 minutes before it does anything, then i get the above error message.
Click to expand...
Click to collapse
OK But are you also holding your stylus in the Reset Hole?
If yes, And you can't get into Bootloader, well I think you are "boned"

Yes im doing that. Boned? really? What about the error message that eventually comes up? isnt there anything i can do from there? Any other way of reseting it so maybe the bootloader works?
And if its really broken, do you recon my network will send me another or have i just properly voided the warranty?

I can´t get by the align screen?

Hi, would be really glad to get some help to get by the align screen!
The display is a little scratchy but it works, now 2 questions:
1: is there a way to using the computer or somthing to get rid of the align screen
Had this problem once before after installing a new rom, but then it worked out after many tries, but now it seems impossible just keep hunting the cross
2: Can you change the plasic over the touch screen (i have a HTC touch diamond)
Tnx in advance /would like to try the now rom - http://forum.xda-developers.com/showthread.php?t=521941

Can you connect via active sync?
If so you can use MyMobiler to connect and click to align.
Or I also found this:
http://pdaphonehome.com/forums/sams...02003-skip-align-screen-after-hard-reset.html
not sure what it is, but it might help...

fnx for the fast reply, tried my mobiler and i see the screen on my computer but i cant use the mouse to align - still need to push on the screen on the mobile... and i cant get by the align screen, ill guess ill try the other link u had there! tnx again

Unplug the phone and just hit the power button off for a couple seconds and hit it back on.
If that doenst get you out of align screen just reboot the device and when it starts back up and gets stuck at align screen just plug it into your computer and wait till it syncs with active sync. Now use the computer to delete welcome.lnk from device memory/windows/startup folder. Unplug the phone and reboot the phone again.
Let me know if this helps you out.
Ryan

tnx, for the help, i used the program on the first link and it worked - guess deleting the welcome.lnk work aswell!!! Now to the second question, can you replace the scratched plastic? i cant use the upper right corner on the touchscreen, kinda annoing to not be able to press the x or ok botton there....
Tnx again

cant find windows folder when i connect it to the pc? program dont work anymore so i guess its only to delete the welcome.lnk left but cant find it on my device?`what to do, cant get pas align screen...

Hit back home or "hang up". If you cant figure out how to use your phone, frankly, replacing the screen is probably gonna be to difficult for you to deal with yourself. Take it to a repair shop or get a new one.

Nothing works... just keep hunting the cross on align screen, cant get past it using the program on the link, and not buy pressing power button on and off, tried every button on the phone aswell, and cant find windows folder when connecting to active sync!!! so any ideas would be apprechiated

make sure in the folder option onthe pc you allow the pc to see hidden files and folders
windows is a system folder and they really dont like people pising about with it
so just enabling the "show hidden files and folders" in the option should show the windows folder also you may run into and issue were you cant delete the file you need to as its prtected. to get round this you need to download total commander on ur phone then navigate to windows folder and delete the file
totalcommander will erase anything you want as itll get round the protection

Hi, tanks for all the help, but it starts to get really annoying.... tried everything you guys have told me, but nothing work Found the windows folder but i cant delete the welcome.lnk as you told me! cant install total commander because i cant get past align screen - what to do? tnx again

look for an program called everywan for the pc
its a bit like my mobiler but itll show you memort processes running on the phone all you have to do is quit the welcome head app then you can get into phone. then use total commander to delete the file
this will need to be done one everyhard reset

[Q] GSM6711A Update?

Hello everyone !
The phone I ordered just got here.
its the same thing as sharper image 202tsi.
Buy dot com has the same phone. you can see it there. (im not allowed to post direct links)
The SW version
GSM6711A-R10-080305-NEPTUNE
Hardware version
GSM6711A_1.4
Device Information
System - smartphone
Producer - AMOI Eletronics
System Version 5.02
The box says its got GPS. But Im not able to figure out how to use it
Is there an update for this phone?
Any thing about this phone will be really helpful to me
Thanks

I have not been able to figure it out either.. checked purehitech website too.. they have nothing on the site...
there is no info on this phone anywhere!!!!

i was trying to reset the phone because it had user code and find that presing:
power + camera the screen went to download
power + left and right soft keys and back button makes clear storage
power + home, left and right soft keys goes to usb calibration.
i didnt find gsp on the phone.
hope this is useful because i didnt find anithing either.

Thx for the post Lennyomar
Your post helped me Hard Reset my Sharper Image PUERHITECH 202TSI phone that I bought from ebay locked with a password and couldn't figure out for the world how to hard reset the darn thing.
Step one
1. Power + left + right + back(next to the right soft key) buttons while system is still powered on.
Keep trying till you see the screen change to blue with the words "Clear Storage"
2. I had to press the letter "Y" (I think it helped?) and the "ENTER" button at the right corner of the keypad.
The screen turns black for a few seconds comes on with the sharper image logo and stays there re-imaging the phone. After about 2 minutes of waiting, voila! WinMo oh my GOD 6. Pretty ancient but it worked.
Now if someone can help me uograde to WINMO 6.5 would be great.

I realize this is an old thread, but just in case anyone is following it: I downloaded and installed EnableGPS (google it) which was made for an HTC phone, but it worked to enabel the internal GPS on this phone. I now have an active internal GPS that works with NoviGPS and will hopefully work with others. Now if I can only determine if there is WiFi (there are references in the registry) and get it enabled, then I will be so-o-o happy!
Amoi 6711 or Alcatel 202TSI or VDA-GPS or....

This device is similiar to toshiba g710 and vda-gps so there is no hidden wifi sorry... there is no possibilitiy to have wifi... but tell me about this gps trick you did? where did you found it?

The file is attached. Use at your own risk, but it worked for me, GPS is now accessable. Try also downloading and installing GpsTest from Chartcross. It will show you your working GPS. Enjoy!

It does not work for me it shows gps in garmin xt bud doesnt find any satellite