Hi,
My xoom MZ600 (3G UDMA) does not boot after ICS OTA.
ICS hangs on tiles animation. Shows flying tiles looping forever.
Debug mode is off and xoom is not rooted.
Driver does not install in XP because xoom does not boot. It stalls with the message 'Installing PCM', so I can't use adb. Fastboot command shows a 'waiting for device' message
I did a wipe reset and erased cache from recovery I tried to install Team eos with a usb drive from recovery mode but I get errors.
I'm stuck...
Any help would be greatly appreciated.
Thanks!
When the message waiting for devices appears, press power and vol up.
Once moto logo appears, press vol down, this should hold for 20 seconds, and your fast boot commands should go thru.
Sent from my MZ601 using Tapatalk 2
thank you wesamothman,
I know how to enter fastboot.
Once in fasbood mode what should I do?
I tried to boot from usb but I get errors.
Thanks again!
Related
Hi there,
I have a rooted and unlocked UK T-Mobile Atrix.
After following the CM7 Beta instructions up to this point:
While in Recovery install CM7 from internal storage
After installation select Data Wipe/Factory Reset
Then Wipe Cache Partition
Reboot system now
Watch awesome boot animation.
I rebooted, but have not seen the awesome boot animation (and I so want to see it) and am now stuck on the initial Dual Core splash screen.
I noted from a couple of posts in the CM7 thread that using Tenfar's CWM may be the cause of the issue.
Unfortunately I am unsure what to do now to fix my mistake and get a rom on the phone and boot it.
Please can someone help?
Thanks
Well...i got the same problem, maybe more worst....i`m stuck on S E logo for 7-10 seconds and after is rebooting again alone and again, i`m not able to go to xrecovery mode and as well i cannot to stay connected on my computer with the phone...is any chance to repair my phone or is time to drop on my recycle bin? Thanks!
I managed to find a solution (should have searched harder...) I followed these instructions here "code(.)google(.)com/p/atrix-dev-team/wiki/BackupRestore"
Flashing CWM Recovery via Fastboot
Download the latest CWM recovery from Downloads section (recovery-cwm-ext4.img)
Power off phone
Put phone into fastboot (Power + Vol Down Button)
Press Volume Up button to select Fastboot
Connect phone via USB cable
Open Command Prompt from your fastboot directory
Type "fastboot flash recovery recovery.img" (no quotation marks)
Type "fastboot reboot"
Followed by pressing volume down during the reboot, then pressing volume down repeatedly until Android Recovery appears on screen then pressing up. This allowed me to reapply the CM7 rom and all was good.
I'm not sure if this helps you Hellspawm, but good luck.
BLESS YOU! you helped out a noob in distress I had the exact same problem and it's fixed now.
Couple of days ago I opened up my TF and saw it was stuck on the bootup screen. Since then I have tried multiple times to format /system and do a factory restore in CWM and tried reflashing EOS JB and RaymanFX JB. Both times the TF boots so it shows the blue bar on boot sliding across to show it updated and then dies and reboots and gets stuck on the bootup screen. Is there a way to fix this?
And the loading screen I'm talking about is the one that says eee pad in cursive and "Powered by Nvidea Tegra" on the bottom.
Thanks.
did you flash kernal from RaymanFX
If you are ready flash kernal just go back CWR and selected "Boot recovery" in misc menu
waiting little bit long in the first time but it'll be login successful, it's my experience ^^
note: and flash google app too "gapp"
leonly1232 said:
did you flash kernal from RaymanFX
If you are ready flash kernal just go back CWR and selected "Boot recovery" in misc menu
waiting little bit long in the first time but it'll be login successful, it's my experience ^^
note: and flash google app too "gapp"
Click to expand...
Click to collapse
Isn't the kernel built into the ROM? I guess I will give that a try.
It is better to clean isntall.
Format /data etc.
then isntlal the rom
or download Super Wipe Full form ARHD: http://forum.xda-developers.com/showthread.php?t=1245892
good luck :]
Do not use super wipe...
Install twrp 2.2.1(recovery)
Use that recovery to wipe internal memory, cache, dalvik and everything else..
Now do a fresh installation of CM10 or eos jb... mind u cm10 gives better audio then eos and cm10 has kernel inbuilt which is better than eos kernel...
Sent from my Transformer using xda app-developers app
Basically wiped and formatted everything and downloading CM10 right now. Hopefully this will work.
Tablet has booted into CM and everything seems to be working again. Thanks guys!
Asus Transformer TF101 struck on start screen
Hi,
My Asus Transformer is struck at welcome screen, when I try to reboot with power and volume down buttons, it's saying rebooting but struck at the
following screen
OS will cold boot in 10 seconds if no input is detected
Press <VOL_Down> to change mode
Press <VOL_UP> to confirm mode ( when I press vol_up to confirm mode), I get the following message below
Platform pre OS boot configuration....
Cold-booting Linux
Any help is truly appreciated.
shrihan0 said:
Hi,
My Asus Transformer is struck at welcome screen, when I try to reboot with power and volume down buttons, it's saying rebooting but struck at the
following screen
OS will cold boot in 10 seconds if no input is detected
Press <VOL_Down> to change mode
Press <VOL_UP> to confirm mode ( when I press vol_up to confirm mode), I get the following message below
Platform pre OS boot configuration....
Cold-booting Linux
Any help is truly appreciated.
Click to expand...
Click to collapse
Welcome to the forum!
Are you rooted, or are you still stock?
If you are rooted, what recovery are you running?
If you are stock, I would try flashing the latest (.27) firmware for your version (SKU). Download from the Asus support site, unzip it ONCE (it will still be a zip) and put that on a microSD formatted for FAT32. Then hold VOL DOWN and POWER until you see the small white text. Release both buttons and hit VOL UP to enter RCK (recovery) to trigger the flash of the stock firmware.
Hi folks,
I had installed kitkat 4.4.4 with recovery-clockwork-6.0.4.4-a700, then I decided to try the lollipop 5.1.1 with CM 12.1 and from there I got stucked with a cycle of reboot. It starts, with at centre ACER logo green and top "Bootloader Version JB-653b3d3 (Unlock Mode)" then it comes the CYANOGENMOD and after 5 sec it reboots. If I connect the USB, it is popping out the message (windows 7) that device is connecting but in this little time there is not enough time to establish the connection before it reboots!
I tried to go to the recovery with Press [vol-] + [power], Once the tablet vibrated, let go [power] and keep [vol-], Now the tablet vibrates a second time, let go [vol-] and press [vol+] quickwith, it comes: "Bootloader Version JB-653b3d3 (Unlock Mode)", second row "Entering boot menu" and nothing happen... it does not come the menu of the 6.0.4.4 anymore. I tried to connect the USB cable as well but it is not recognised (ADB DEVICES empty list).
Not sure if anyone is still on the A700 but any help would be very much appreciated!
tuscan72 said:
Hi folks,
I had installed kitkat 4.4.4 with recovery-clockwork-6.0.4.4-a700, then I decided to try the lollipop 5.1.1 with CM 12.1 and from there I got stucked with a cycle of reboot. It starts, with at centre ACER logo green and top "Bootloader Version JB-653b3d3 (Unlock Mode)" then it comes the CYANOGENMOD and after 5 sec it reboots. If I connect the USB, it is popping out the message (windows 7) that device is connecting but in this little time there is not enough time to establish the connection before it reboots!
I tried to go to the recovery with Press [vol-] + [power], Once the tablet vibrated, let go [power] and keep [vol-], Now the tablet vibrates a second time, let go [vol-] and press [vol+] quickwith, it comes: "Bootloader Version JB-653b3d3 (Unlock Mode)", second row "Entering boot menu" and nothing happen... it does not come the menu of the 6.0.4.4 anymore. I tried to connect the USB cable as well but it is not recognised (ADB DEVICES empty list).
Not sure if anyone is still on the A700 but any help would be very much appreciated!
Click to expand...
Click to collapse
I guess minimal version for CWM are:
CM 10 JB CWM 6.0.1.5 minimum
CM 11 4.4 Kit Kat CWM 6.0.4.4 minimum
CM 12 LP 5 Lolipop CWM 6.0.5.0+
You should try to plug it in fastboot mode even if it does not appear in the adb devices list and flash CWM 6.0.5.0 with something like
fastboot flash recovery recovery6050image.img
I know the post is ageing but I have something similar with an A700, except I can get into a broken recovery:. I can perform some operations but no 'wipe cache' action for example, it reboots.
If I plug it in fastboot mode, it doesn't appear in the 'adb devices' list but I can flash different recoveries (but not sideload any ROM).
Some helpful files if you need them (latest A700 CM ROM have 6.0.5.0 recovery associated with the latest 2016 august ROM)
http://download.cyanogenmod.org/?device=a700
http://acer.shreps.fr/
if you can't get to recovery then you need to manually boot to fastboot / usb protocol to try a different one.
the directions are only a couple threads away from this one
So I downloaded an app called "Quick Reboot [ROOT]", and I selected the "fastboot mode" option.
I restarted my device thinking it would go to fastboot mode, but it's stuck at "Starting RSD mode 3".
My computer doesn't recognize the device and pressing volume up + power only makes the Xoom get stuck at the red M logo with no text.
I'm a novice and I'm not sure what to do, any help is greatly appreciated.
Thanks in advanced.
Go to fastboot or recovery by pressing vol down 3 sec`s after u see the Motorola Logo.
delete cache and try booting up again.
I was installing the fulmics 3.5 rom with magisk option. The magisk was not working correctly so I attempted to update, but received an error that the image was already modified. So I reinstalled fulmics this time with just super user.
Once in rom, I went to su and clicked the uninstall option and rebooted and was going to flash the magisk zip. However, I am stuck at LG logo when booting up.
My phone launches the LG boot logo, switches to the "cannot check for corruption please lock bootloader" screen and back to the booting animation with the LG logo. I can tell it's the booting animation because the brightness goes down.
I cannot get the phone to go into download or recovery mode. I press volume down and power and upon LG logo I release power and press again. Same with volume up.
Adb or fastboot does not recognize device and USB drivers are installed. I'm assuming this is because it isn't in fastboot or debug mode?
Am I bricked or can I get out of this?
EDIT 3: I used this guide to restore functionality. https://forum.xda-developers.com/lg...-mode-lgup-t3565508/post71239406#post71239406
I'm able to see my phone with LG UP while it is trying too boot. I can't proceed though because it says the model is unknown.
EDIT: Yes, USB drivers are installed.
EDIT 2: I can get into Fastboot now by plugging in cable and holding vol -, but fastboot reboot recovery is not working.