Hello.
I have a problem with a Touch HD2. Sometimes, when I send a message, it doesn't get sent until I restart / reboot the phone. When I do, all the messages gets sent at the same time.
I had the same problem with a Touch HD some months ago.
Anyone know how to fix this?
Thanks for help.
Gissan said:
Hello.
I have a problem with a Touch HD2. Sometimes, when I send a message, it doesn't get sent until I restart / reboot the phone. When I do, all the messages gets sent at the same time.
I had the same problem with a Touch HD some months ago.
Anyone know how to fix this?
Thanks for help.
Click to expand...
Click to collapse
hmm, interesting one, what is your device currently set to for sending messages, i.e. GSM, GPRS?
Have you recently updated rom, radio or changed ril?
Have you tried running automatic setup again?
Can you provide more info please
Yeah, could be a radio problem or your phone not logging onto local masts.
Try a manual roam,.... Go to your network selection, search for available networks, then pick a network you are not on, ideally a network that uses a diff network frequency band thing. So if your nwtwork uses 900 research one that uses 1800 or vice verser. When you select this 'wrong' network it sould give you some kind of error and you should lose all network coverage. Then re select your correct network.
Try power cycling,... Turn off your phone, remove SIM & Battery, hold power button for 5 - 10 seconds. Then put everything back in and turn on.
Last one,... Go onto internet on handset, load a page you have never been on before that has alot of data on it, amazon or something, while its trying to load the page pull the battery out. Then power cycle as above.
I worked for Vodafone Cust services about 8 yrs ago,.... those 3 things usually sorted network issues.
+1
I have exactly the same problem on my HD2.
It's very occasional, and just a soft reset is necessary and everything's fine again.
I don't know why this happens.
Thanks
Franky
Hello dear community,
I have a strange issue with my HTC ONE S:
HOME button activate on itself and loop(switch from miniatures to home page). After a while the three buttons are de activated.
Interrupt any activity you can have.
Not due to hand/finger misuse: it can happen phone lying on a desk…
Remark: It happens only when GSM/3G signal is very low. Plane mode solve the issue, but then it is hard to phone...
you can find a demo of buttons deactivated here(http removed I can't post links):
youtu.be/gfzBbMPHqjE
Do you have similar situations?
Do you think I should send it back to supplier? Or a baseband update could help if I'm patient?
Versions:
Android: 4.0.3
HTC Sense: 4.0
Software number: 1.53.401.2
HTC SDK API level: 4.11
HTC Extension version : HTCExtension_403_1_GA_4
Kernel version: 3.0.8-01500-ge2a40ab
Baseband version: 0.15.31501S.19_10.12.31501S.06L
Browser version: WebKit/534.30
OK, I suppose I'm alone in this situation...
Looks like a good return reason.
Some Antennas are directly behind the snsitivie buttons (below the lower plastic cap) so maybe some are misaligned and cause interference bad enough to trigger the buttons. You mention of using flight mode to cease the problem kind of makes me think this might be the case.
Im getting similar issue. Had this twice, thought its because of "shock", had this while driving and using maps, but just had it in my hands...
Any info about this problem?
issue gone
Hi,
The bug didn't happen since 4 days now.
I travelled by car on 350km using GPS, sms...
No more issue even with low signal.
pierre.grand said:
Hi,
The bug didn't happen since 4 days now.
I travelled by car on 350km using GPS, sms...
No more issue even with low signal.
Click to expand...
Click to collapse
you did any fix? or it disapiered itself?
Stiflerlv said:
you did any fix? or it disapiered itself?
Click to expand...
Click to collapse
Hello,
at the beginning I did 2 factory reset but the bug still happened.
Then no other change.
what I can notice is that the radio signal level is changing all the time between very different value even if not moving...I think there is some kind of radio instability...
EDIT: "WCDMA Only" setting is the key! That disables EDGE that is the source of problem.
Home screen button problem
Hi,
I'm also having this problem and am about to get my third replacement One S. I started a thread about it on the Vodafone forum which a few other people have now replied to with the same issue, although no one as yet can figure out exactly what's going on. I too think that it has something to do with the antenna being located near to the home button, as the problem seems to show itself every time I make an EDGE connection. HTC are apparently investigating my issue and have asked me to send them a bug report.
I'm not allowed to post the link to the Vodafone thread on here however you can find it by typing "htc one s home button problem" into Google.
After today I stopped believing its releated to H/3G signal change.
I just unlocked my phone (gps/wifi/mobile data - all OFF) and right after unlocking home button glitched... Didnt do anything...
Im gonna go for exchange soon
P.S. question - how are phones exchanged for you guys? They take it and send to service center, or just exchange right away? How it works? Never done that
I'm with Vodafone and they just offered to exchange it as soon as I explained the problem to them (I was within 7 days of having received it). The second phone had the same issue though so they then agreed to replace that as well, but they then sent me a reconditioned phone by mistake, so I'm now waiting for a fourth phone.
Hi
I did some testing and this issue is linked 100%, to EDGE. When "WCDMA only" is set : no issue.
HTC ONE S is unusable on EDGE network...
Hello
i instantly register on XDA forum because i have exactly the same issue with my HTC One S.
I have it since four weeks, i was very satisfied but this issue appears to my parent's house. Exactly the same issue: HOME button activate on itself and loop(switch from miniatures to home page). After a while the three buttons are de activated.
I returned at home and the issue disappears!
I confirm the pierre.grand's observations: i'm in EDGE to parent's house and WCDMA at home.
How to alarm HTC on this disturbing issue? I hope an update firmware will be soon...
Loop Problem
i have the exact same problem, but it seems that
the problem wont go away after turning off edge (mobile data)
Anyhow, it seems like its acting up when i shake the phone?
any ideas ?
Thanks for all help
BR
Kim
Kimsa said:
i have the exact same problem, but it seems that
the problem wont go away after turning off edge (mobile data)
Anyhow, it seems like its acting up when i shake the phone?
any ideas ?
Thanks for all help
BR
Kim
Click to expand...
Click to collapse
It looks like the problem on my phone is when edge/3g or wifi is connected
When i turn of wifi and edge/3g the phone acts pretty nice!.
Is this related to firmware or hardware, ?
if its fw its no use compling to my the store, HTC Support does not "know anything about this error...".
Has anyone experienced this problem, and tried flashing costum rom?
do the problem still follow?
Thanks for all help.
br
Kim
I have the same problem. But I have installed Trickdroid 1.0,
CWF did not solve the problem.
cu goohnie
Phone returned.
But they sent it back to me syaing there is no problem. They made a firmware upgrade.
I'm now waiting for it.
Do you have some feedbacks?
How long did it take for the problem to appear? I'm always on EDGE with Wi-Fi on (due to TMOUS' lousy coverage at my home) and I haven't had any problems.
Nick L said:
How long did it take for the problem to appear? I'm always on EDGE with Wi-Fi on (due to TMOUS' lousy coverage at my home) and I haven't had any problems.
Click to expand...
Click to collapse
It's happening on EDGE used as data connection: that means no WIFI.
The signal has to be low(problem doesn't occur if signal is correct) and the phone has to be switching very often between EDGE and 3G.
Then when it is in EDGE, the issue occurs.
If you try to switch off the screen, it takes screenshots(HOME combination with POWER button, normal behaviour since HOME button activates all the time).
If you put you finger on the HOME button, the flickering stops.
After a while, the buttons deactivate on their own and the touch screen works fine.
Then you can switch the screen off and then on the buttons are back.
after a while if you are in the same location the issue reappears(difficult to give you the exact frequency since it's linked to sognal force it depens on the place you are standing).
I was using a back cover at the beginning and it makes the issue more present, I suppose this is because of the reduction of signal that happens...
At home I have a great signal, then even if I force EDGE only I get no problem...
pierre.grand said:
It's happening on EDGE used as data connection: that means no WIFI.
The signal has to be low(problem doesn't occur if signal is correct) and the phone has to be switching very often between EDGE and 3G.
Then when it is in EDGE, the issue occurs.
If you try to switch off the screen, it takes screenshots(HOME combination with POWER button, normal behaviour since HOME button activates all the time).
If you put you finger on the HOME button, the flickering stops.
After a while, the buttons deactivate on their own and the touch screen works fine.
Then you can switch the screen off and then on the buttons are back.
after a while if you are in the same location the issue reappears(difficult to give you the exact frequency since it's linked to sognal force it depens on the place you are standing).
I was using a back cover at the beginning and it makes the issue more present, I suppose this is because of the reduction of signal that happens...
At home I have a great signal, then even if I force EDGE only I get no problem...
Click to expand...
Click to collapse
Tried to make the problem show up (select WCDMA only, let it connect and then switch to auto and let it drop to EDGE) and nothing happened. Also had a few "natural" 3G-2G drops with no problem. US phones could be different (different bands) though.
I have exactly the same problem.
It's happend only on edge, 2g mode.
That might be problem with more phones. People please check your mobiles, switching only on 2g(gsm) mode and turning off wifi.
My phone always gets mad when the single data packet is send.
Unfortunatly that makes phone unusable for me, in work i have only GSM coverage, the same in home. I can use internet only in the places where is WCDMA or wifi.
People better check your phones, nobody knows when phone may fail you if you'll be in GSM coverage only.
Hi guys,
I have a i727 skyrocket use in Germany. (unlock phone)
The network provider is Vodafone.de.
The phone works fine if you only use it in 2G network both call and data. (stock rom by using *#2263# or *#*#4636#*#*, CM9 rom by select 2g only, or *#*#4636#*#*)
But when I turn it to 3g network, problem happened. (both in WCDMA only or WCDMA preferred)
It appears like, when you power on/restart the phone, at first you can see 4G (stock) or H+/H/3G (CM9) icon and the data arrows flash. At this period you can make calls or browse website. But after maybe 30 seconds or 1 minute, when 4G or H icon gets stable. Then you can’t make calls out and if you use another phone to call it, the voice tells you the number you called can not be connected. And also the data was stopped; the browse shows network problem/times out or the same kinds of notice.
Then I use “GSM Signal Monitoring”, try to find out some regular patterns. I found when the signal switch from one base station to another, at first the phone functions is ok, and later when the signal is stable, the phone dead, and maybe several minutes after, when the phone switch to another station, the phone function works again, then about 30 seconds later, dead again. But in all this periods the signal is quite good. (around -60~-80 dBm)
At first I think maybe is the problem about RADIO.
So I try to flash many different RADIOs (T989, T989D, I727R, I757M, I9210, I9210T, E120K, E120S both from stock 2.3 or 4.0 and both with or without RIP), but they all didn’t solve the problem.
And also I try different ROMs (stock 2.3, 4.0; I727R 2.3, 4.0; T989 4.0, CM9; CM10), and the combination with the radios above, but still didn’t work.
Then I noticed some threads about the fast dormancy, I have tried to turn the fast dormancy off or on. But still didn’t work.
Also I noticed about different 3G data forms (HSPA+, HSUPA, HSDPA, UTMS), then I used *#301279# on stock rom to fix the 3g data form in only one kind or only use UTMS, but still didn’t work.
And later I found it is not about the data connection, it is only about the 3G network no matter about the data is on or off, when you switched to WCDMA, then, when the signal stable, you can’t make calls out or receive calls in, and even the signal bar seems great from the begin to the end.Another thing is if you making a call at the first “alive” period, then before you hang up the phone, it all works. Also if you use some online radio software keep the data flow, and the phone will not “dead”, only when the phone is idle, and later after sometime, the signal “dead”.
And the SIM card works fine in other phones in 3G network.
I have tried this in my home and office. In the office the signal always switched to different stations, so it looks a little better. But at home, the signal always stays in one or two stations, so it much easier to see when signal stable, the phone dead.
This problem confused me already 1 month, I tried everything I found and everything I can image. But everything didn’t work. At this moment, I only can use it under 2G networks.:crying::crying::crying:
I am sorry about my English; I try to explain these clearly.
Really hope someone can help me.
tjxboy said:
Hi guys,
I have a i727 skyrocket use in Germany. (unlock phone)
The network provider is Vodafone.de.
The phone works fine if you only use it in 2G network both call and data. (stock rom by using *#2263# or *#*#4636#*#*, CM9 rom by select 2g only, or *#*#4636#*#*)
But when I turn it to 3g network, problem happened. (both in WCDMA only or WCDMA preferred)
It appears like, when you power on/restart the phone, at first you can see 4G (stock) or H+/H/3G (CM9) icon and the data arrows flash. At this period you can make calls or browse website. But after maybe 30 seconds or 1 minute, when 4G or H icon gets stable. Then you can’t make calls out and if you use another phone to call it, the voice tells you the number you called can not be connected. And also the data was stopped; the browse shows network problem/times out or the same kinds of notice.
Then I use “GSM Signal Monitoring”, try to find out some regular patterns. I found when the signal switch from one base station to another, at first the phone functions is ok, and later when the signal is stable, the phone dead, and maybe several minutes after, when the phone switch to another station, the phone function works again, then about 30 seconds later, dead again. But in all this periods the signal is quite good. (around -60~-80 dBm)
At first I think maybe is the problem about RADIO.
So I try to flash many different RADIOs (T989, T989D, I727R, I757M, I9210, I9210T, E120K, E120S both from stock 2.3 or 4.0 and both with or without RIP), but they all didn’t solve the problem.
And also I try different ROMs (stock 2.3, 4.0; I727R 2.3, 4.0; T989 4.0, CM9; CM10), and the combination with the radios above, but still didn’t work.
Then I noticed some threads about the fast dormancy, I have tried to turn the fast dormancy off or on. But still didn’t work.
Also I noticed about different 3G data forms (HSPA+, HSUPA, HSDPA, UTMS), then I used *#301279# on stock rom to fix the 3g data form in only one kind or only use UTMS, but still didn’t work.
And later I found it is not about the data connection, it is only about the 3G network no matter about the data is on or off, when you switched to WCDMA, then, when the signal stable, you can’t make calls out or receive calls in, and even the signal bar seems great from the begin to the end.Another thing is if you making a call at the first “alive” period, then before you hang up the phone, it all works. Also if you use some online radio software keep the data flow, and the phone will not “dead”, only when the phone is idle, and later after sometime, the signal “dead”.
And the SIM card works fine in other phones in 3G network.
I have tried this in my home and office. In the office the signal always switched to different stations, so it looks a little better. But at home, the signal always stays in one or two stations, so it much easier to see when signal stable, the phone dead.
This problem confused me already 1 month, I tried everything I found and everything I can image. But everything didn’t work. At this moment, I only can use it under 2G networks.:crying::crying::crying:
I am sorry about my English; I try to explain these clearly.
Really hope someone can help me.
Click to expand...
Click to collapse
Why are u flashing radios for other phones???? That cud be ur problem right there.....try flashing a modem/radio for the i727 skyrocket
Edit: try flashing one of these radios for the SKYROCKET.....if that dnt work u may need to warranty ur phone out and get it replaced.
http://forum.xda-developers.com/showthread.php?t=1785999
Sent from my SGH-I727 using xda app-developers app
jyazzie110 said:
Why are u flashing radios for other phones???? That cud be ur problem right there.....try flashing a modem/radio for the i727 skyrocket
Sent from my SGH-I727 using xda app-developers app
Click to expand...
Click to collapse
because from the begining the original rom and radio have this problem,
then i have to try some other radios,
hope may solve this problem.
but neither the stock nor other ROM/RIDAO works. ............
jyazzie110 said:
Why are u flashing radios for other phones???? That cud be ur problem right there.....try flashing a modem/radio for the i727 skyrocket
Edit: try flashing one of these radios for the SKYROCKET.....if that dnt work u may need to warranty ur phone out and get it replaced.
http://forum.xda-developers.com/showthread.php?t=1785999
Sent from my SGH-I727 using xda app-developers app
Click to expand...
Click to collapse
Thanks for your help.
I have already tried most of them in this thread before.
nothing changed..T_T
tjxboy said:
Thanks for your help.
I have already tried most of them in this thread before.
nothing changed..T_T
Click to expand...
Click to collapse
I did the same as you, tried a lot of rom/kernel/radio combination without any luck.
Im not in US too, and I notice something that when it happens the network type changes from HSPDA to Unknown, but my carrier ID still there.
I Think that is happening maybe because I don't have a LTE signal here and the phone tries to connect to something in that band frequency and it somehow "hear" something in that frequency then lock it up there.
I notice that if i got into the radio menu *#2263* ( depending on the rom u r using) and set it to be just gsm. I will always get calls and data, but in eDGE speed and it sucks... If i set it to WCDMA only it eventually get signal drops. And the last choice is that Auto mode that I think got the LTE enable. I think if we could select the WCDMA preferred/ GSM option of the radio i727ruxfl3 it would solve our problems, but it appears to be an invalid solution.
Ive been looking around to learn how to change the radio code but no lucky yet...
filipeangelo said:
I did the same as you, tried a lot of rom/kernel/radio combination without any luck.
Im not in US too, and I notice something that when it happens the network type changes from HSPDA to Unknown, but my carrier ID still there.
I Think that is happening maybe because I don't have a LTE signal here and the phone tries to connect to something in that band frequency and it somehow "hear" something in that frequency then lock it up there.
I notice that if i got into the radio menu *#2263* ( depending on the rom u r using) and set it to be just gsm. I will always get calls and data, but in eDGE speed and it sucks... If i set it to WCDMA only it eventually get signal drops. And the last choice is that Auto mode that I think got the LTE enable. I think if we could select the WCDMA preferred/ GSM option of the radio i727ruxfl3 it would solve our problems, but it appears to be an invalid solution.
Ive been looking around to learn how to change the radio code but no lucky yet...
Click to expand...
Click to collapse
In my case, the network type changes from HSPA+:15-->UTMS:3-->HSPA:11, then stop changing. If you send some internet request immediately after this, the network type will change back to UTMS:3--> HSPA+:15 again. But If you do nothing, after some time, the network fully dead.....Only when the phone switches to anther station, the network type changes again. Because I noticed this, I tried to fixed the network type in HSDPA:9 or UTMS:3, but the network still will die when the signal stable.
In my place, we do have a LTE network, but the frequency here is different from north america. And my problem is only in WCDMA, so I think it is not related with LTE network.
As I said, it works well in 2G network both in GPRS and EDGE; and in 3G, the signal is also strong, nearly full bar.
Maybe my case is a little different from yours.
But in your case, I think you can use *#*#4636#*#*, to lock the signal in WCDMA only or WCDMA preferred, it is the same as you use *#2263#, only the words is a little different.
WCDMA only in *#*#4636#*#* = WCDMA preference in *#2263#
WCDMA preference in *#*#4636#*#* = WCDMA/GSM preference in *#2263#
You can try to test whether your theory is right.
tjxboy said:
In my case, the network type changes from HSPA+:15-->UTMS:3-->HSPA:11, then stop changing. If you send some internet request immediately after this, the network type will change back to UTMS:3--> HSPA+:15 again. But If you do nothing, after some time, the network fully dead.....Only when the phone switches to anther station, the network type changes again. Because I noticed this, I tried to fixed the network type in HSDPA:9 or UTMS:3, but the network still will die when the signal stable.
In my place, we do have a LTE network, but the frequency here is different from north america. And my problem is only in WCDMA, so I think it is not related with LTE network.
As I said, it works well in 2G network both in GPRS and EDGE; and in 3G, the signal is also strong, nearly full bar.
Maybe my case is a little different from yours.
But in your case, I think you can use *#*#4636#*#*, to lock the signal in WCDMA only or WCDMA preferred, it is the same as you use *#2263#, only the words is a little different.
WCDMA only in *#*#4636#*#* = WCDMA preference in *#2263#
WCDMA preference in *#*#4636#*#* = WCDMA/GSM preference in *#2263#
You can try to test whether your theory is right.
Click to expand...
Click to collapse
Im using SuperHeavy JB rom and Blaze LF4 radio that is the best combination i got so far. I still get network lockouts but its not as common as other combos. My theory is that the radio connects to some band then it loses the signal and somehow it doesn't detect that the signal is lost.
Cause I was looking at the *#*#4636#*#* and the uplink still sending data, but it doesn't get a response back.
filipeangelo said:
Im using SuperHeavy JB rom and Blaze LF4 radio that is the best combination i got so far. I still get network lockouts but its not as common as other combos. My theory is that the radio connects to some band then it loses the signal and somehow it doesn't detect that the signal is lost.
Cause I was looking at the *#*#4636#*#* and the uplink still sending data, but it doesn't get a response back.
Click to expand...
Click to collapse
Yes, I am quite agree with your theory.
I noticed the same thing as you mentioned,
When the signal is dead,
you still can see the phone send some request to the network,
but no respond.
So I think it maybe influenced by the fast dormancy.
Maybe the phone and the network have some problem in fast dormancy policy.
Then I use the way which was described in the forum, add some information into the database.
But unluckly, still didn't work.
I will try your combinations to see if something changes.
Thanks a lot.
filipeangelo said:
Im using SuperHeavy JB rom and Blaze LF4 radio that is the best combination i got so far. I still get network lockouts but its not as common as other combos. My theory is that the radio connects to some band then it loses the signal and somehow it doesn't detect that the signal is lost.
Cause I was looking at the *#*#4636#*#* and the uplink still sending data, but it doesn't get a response back.
Click to expand...
Click to collapse
report:
I just tried this combination, SuperHeavy rom (V6.0SR, based on CM10), and blaze 4g LF4 radio. But still the same, the signal dead after the signal is stable. T_T
You can see a H on the bar, and the signal if full.
But when you use "ping" in *#*#4636#*#*, the result is "Fail:IP addr not reachable"
...................................
Here are two screenshots.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
The first is when the signal is satble, have a "H" icon on the bar and the network connection is "stop".
At this moment, you can see good signal, but you can't make any calls, and no data.
The second is just when the phone switched to another base station, have a "H+" icon, at the first short moment, everything works find.
But, several seconds later, the "H+" turns to "H", then, every communication down.
tjxboy said:
Here are two screenshots.
The first is when the signal is satble, have a "H" icon on the bar and the network connection is "stop".
At this moment, you can see good signal, but you can't make any calls, and no data.
The second is just when the phone switched to another base station, have a "H+" icon, at the first short moment, everything works find.
But, several seconds later, the "H+" turns to "H", then, every communication down.
Click to expand...
Click to collapse
I wipe everything and started a new installation. The rom version is a gingerbread one. I thought what the heck i will do the downgrade, better a working phone with an old OS the a great OS with non working phone.
I tried the Nexusmod 4.3.1 with the radio i727UCLA3. Its been just 4hrs tethering but so far so good. Give it a try.
Another thing is looking down the web i found that more ppl are having this issue, but they are using other devices such as nexus,and they fixed by simple softwares updates, I might not be the same problem but it gave me hope that it could be software related not hardware as I ve started to suspect.
tjxboy said:
Here are two screenshots.
The first is when the signal is satble, have a "H" icon on the bar and the network connection is "stop".
At this moment, you can see good signal, but you can't make any calls, and no data.
The second is just when the phone switched to another base station, have a "H+" icon, at the first short moment, everything works find.
But, several seconds later, the "H+" turns to "H", then, every communication down.
Click to expand...
Click to collapse
Hey Im trying a new thing, I took out the SD card and changed the SIM card. I have installed the CM JB 4.1.2 nightly,after that i let it settle for 10min before I do anything in the room. Well since yesterday i got data and calls whenever I want.
You should try.
filipeangelo said:
I wipe everything and started a new installation. The rom version is a gingerbread one. I thought what the heck i will do the downgrade, better a working phone with an old OS the a great OS with non working phone.
I tried the Nexusmod 4.3.1 with the radio i727UCLA3. Its been just 4hrs tethering but so far so good. Give it a try.
Another thing is looking down the web i found that more ppl are having this issue, but they are using other devices such as nexus,and they fixed by simple softwares updates, I might not be the same problem but it gave me hope that it could be software related not hardware as I ve started to suspect.
Click to expand...
Click to collapse
Thanks.
I tried the same you said, still the same problem....
T_T
filipeangelo said:
Hey Im trying a new thing, I took out the SD card and changed the SIM card. I have installed the CM JB 4.1.2 nightly,after that i let it settle for 10min before I do anything in the room. Well since yesterday i got data and calls whenever I want.
You should try.
Click to expand...
Click to collapse
The same I tried, took out SIM card (no install TF card), install clean ROM, restart, let it settle for half an hour, then, insert SIM card.
Unfortunately, still the same.
But I found some thing, when I use my frineds' SIM card which from other network provider (O2, E-plus in Germany), and the phone in their 3g network seems works well.....
So maybe this only about the phone and the vodafone network, maybe some compatible problem. It is really disappointed.
I contacted with vodafone company but no reply yet.
I think maybe the only way I can use this phone properly is to change to another network. T_T