Database Info

[Q] Getting Back to stock WW Rom

Whats the best way to get back to a stock rom after using a custom rom from US region. Obviously I'm rooted and CWM installed. If I put the ww rom on the sd card and rename in asus\update to higher number it tells me there is an update, but when it tries to install it, it jsut goed back into CWM. Should I unroot 1st so it will the run the normal recovery? or is there any way I can convet a stock rom to a CWM .zip file to get back. If I point CWM at the zip file, it does some stuff then fails on me. Anyone able to point me and anyone whos interested in the right way to do this without bricking our devices
I am on a custom 3.1
Should I unroot using the blob in the 3.1 rom, and the try running the update from asus/update directory? I am just afraid of getting to a point where I can't go back or forwards, because I will lose clockwork to put a custom rom back. The nandroid backup I did before installing the 3.1 wont restore saying it has a bad MD5, so this has been no help to me
Cheers
Thanks

Wrong forum.

singlebyte said:
Wrong forum.
Click to expand...
Click to collapse
^This Anyway, I flashed back to Prime v1.3r2, then pushed the blob from 8.2.3.9.
Sent from my HTC Eva 4G using Tapatalk

Ok So I fo;;owed the unroot tutorial, using the blob from the US 3.1
open cmd promt window type the following and return after each.
\cd
\cd AndroidSDK\platform-tools\
adb devices
*adb your device make sure it is hooked up and id'ing your transformer.*
adb push blob /data/local
adb shell
*at the # type the following*
dd if=/data/local/blob of=/dev/block/mmcblk0p4
*wait a few mins to be safe*
now reboot the device, on reboot you should see a progress bar indicating the flashing of the “blob” file. this will remove the clockwork recovery and put your tablet into BOOTLOOP this is ok.
But one I get to this the tablet boots into android, all sign of CWM and root have gone, but I now cant flash a WW rom on top. If I place in ASUS\UPDATE on the SD, it see the update and reboots. I get a big android with cogs that spin for a while then it stops with a big exclamation mark. If I try doing by renaming to EP101_SDUPDATE.zip on the root and doing power up volume down etc, then i get the android with cogs, and the same happens.... HELP I'm stuck!!

Ok I managed to finally get back to ww .13, for some reason .9 would not work, it locked up as explained above. On restoring .13, I hade to do a factory reset as load of things were crashing all over. But that's fine. At lease now I can return as stock. If anyone has to do the same and is struggling, pm me by all means

wilx said:
Ok I managed to finally get back to ww .13, for some reason .9 would not work, it locked up as explained above. On restoring .13, I hade to do a factory reset as load of things were crashing all over. But that's fine. At lease now I can return as stock. If anyone has to do the same and is struggling, pm me by all means
Click to expand...
Click to collapse
Are you planning on sending it back or something?

bigmo7 said:
Are you planning on sending it back or something?
Click to expand...
Click to collapse
Yes as I have a horrible creek on the LHS where the case is moving. I also now going to swap for a keyboard version

[SOLVED] Soft Brick... Can't install ROMS and pushing does not work.

First of all I decided to install CM10 without making a backup on TWRP 2 (clever Kyle). Then when it was stuck on the bootanimation for about an hour, I got annoyed and looked through the forums for help. "Factory reset, clear caches before installing etc" So I deleted the ROM, factory reset via TWRP, deleted both cache and then tried to install CM10. Failed.
Then I tried to mount the SD card to my computer to try to find other ROMS to install. Viper and Energy both failed. I then tried CM10, Viper and Energy with CWM 5.8, and the installation of all gets aborted almost instantly, which I am guessing means that it failed on there as well. I then tried ADB, and pushing keeps failing. Does anybody have any ideas at all on how to get just any ROM onto the phone so that I can get the official 4.1 update again (my phone was on 4.1 before trying CM10, so the HBOOT is most likely 4.1 as well). Any advice would be greatly appreciated, because having a £350 paperweight is not what I particularly want, especially considering I have another 9 months contract to run and no spare phone on the same network as my current contract.

kylepont said:
Any advice would be greatly appreciated
Click to expand...
Click to collapse
When you say that installing ROMs fails and adb pushing fails, you should tell us what error messages you get.
If you can still get into bootloader, you're probably going to be fine.
First, check that you can mount your sdcard in recovery. I don't mean mount onto your PC over USB, but just mount the sdcard partition onto the root filesystem.
If you can not get into recovery, re-flash one.
If recovery can not mount the sdcard, then you have to go to the sticky on how to fix unmountable sdcard. It involves flashing a stock recovery and then clearing storage from bootloader.
If your recovery is good and your sdcard is mountable, adb pushing should work. If it doesn't, post error messages. Make sure your sdcard is mounted before you try to push fils to it.
In recovery, format system, data, cache, but not sdcard. Then flash a zip. Then boot back into bootloader/fastboot and fastboot flash the boot image that comes with the rom. (Did you do this last step when flashing other roms?)
If this does not work not for you, describe in detail what you do and what you see. If it does work out, I suggest you make a nandroid backup so you can get back to this state, and S-off the device.
-Jobo

touch of jobo said:
If this does not work not for you, describe in detail what you do and what you see.
Click to expand...
Click to collapse
Sometimes a print screen can speak louder than words. This is the problem, I followed the tutorial posted specifically for my phone and that didn't work. (I used a dropbox link because I could only upload 640 x 640 according to the attachments screen, so you can see the full picture here)
www(dot)dropbox(dot)com/s/ei0y16oar828dh4/Picture1(dot)png
EDIT: I used platform-tools instead of tools because Google decided to move the adb application to that folder in the most recent update

Re: [Q] Soft Brick... Can't install ROMS and pushing does not work.
kylepont said:
Sometimes a print screen can speak louder than words. This is the problem, I followed the tutorial posted specifically for my phone and that didn't work. (I used a dropbox link because I could only upload 640 x 640 according to the attachments screen, so you can see the full picture here)
www(dot)dropbox(dot)com/s/ei0y16oar828dh4/Picture1(dot)png
EDIT: I used platform-tools instead of tools because Google decided to move the adb application to that folder in the most recent update
Click to expand...
Click to collapse
Have you flashed the boot.img?
fastboot flash boot boot.img
Sent from my One S using Tapatalk 2

usaff22 said:
Have you flashed the boot.img?
fastboot flash boot boot.img
Click to expand...
Click to collapse
boot.img? (Noob question incoming, prepare your anuses) What is a boot.img and why do I need it?

kylepont said:
Sometimes a print screen can speak louder than words.
Click to expand...
Click to collapse
You get this:
cannot stat 'ROM.zip': No such file or directory
..because either you have not mounted your /sdcard partition, but more likely because you dont have ROM.zip in your working directory.
Either move ROM.zip to the same directory where adb sits, or use:
adb push C:\full\path\to\rom.zip /sdcard/
Also, is the file youre trying to push actually named 'ROM.zip' or something else, like ViperOneS_2.1.0.zip or so..
Edit:
kylepont said:
boot.img? (Noob question incoming, prepare your anuses) What is a boot.img and why do I need it?
Click to expand...
Click to collapse
The flashing instructions for your ROM will likely state that you have to 'flash the boot image (or boot.img or kernel) in fastboot before booting into the rom.
You can find a file named 'boot.img' inside your rom zip. You have to flash that in fastboot. You can do it before or after flashing the rom, but you must do it before booting into the rom.

kylepont said:
usaff22 said:
Have you flashed the boot.img?
fastboot flash boot boot.img/QUOTE]
boot.img? (Noob question incoming, prepare your anuses) What is a boot.img and why do I need it?
Click to expand...
Click to collapse
Extract the boot.img file from the ROM. Place it in your adb folder. Boot into bootloader, select fastboot and connect to PC. Type command fastboot flash boot boot img
Click to expand...
Click to collapse

touch of jobo said:
You get this:
cannot stat 'ROM.zip': No such file or directory
..because either you have not mounted your /sdcard partition, but more likely because you dont have ROM.zip in your working directory.
Either move ROM.zip to the same directory where adb sits, or use:
adb push C:\full\path\to\rom.zip /sdcard/
Also, is the file youre trying to push actually named 'ROM.zip' or something else, like ViperOneS_2.1.0.zip or so..
Click to expand...
Click to collapse
All the boxes are ticked on the TWRP Mount screen, including System and SD card. And yes, I did make sure that it is:
1) in the same folder as the adb
2) called ROM.zip. I tried re-naming it CM10.zip and tried that in the adb and still no luck, without without the .zip file suffix.
And usaff22, does that involve unzipping the ROM that I am using?

Okay, so the boot.img was flashed successfully. I then went back onto TWRP, tried to flash the zip and it failed...

kylepont said:
I did make sure that it is [...] called ROM.zip. I tried re-naming it CM10.zip and tried that in the adb and still no luck, without without the .zip file suffix.
Click to expand...
Click to collapse
It can not find the local file. Make sure the file is not actually called 'ROM.zip.zip' (with 2x .zip ... you seem to have extensions hidden for most types but it shows .zip).
kylepont said:
Okay, so the boot.img was flashed successfully. I then went back onto TWRP, tried to flash the zip and it failed...
Click to expand...
Click to collapse
Which version of TWRP? I don't use it, but I read that the latest version has issues and you should use the previous version (2.2.0? I dont know).
Also, does it say anything interesting when it fails?
Before flashing the zip, did you format your system, data, cache partitions?

EDIT: After repeatedly trying to adb push, I finally got CM10.zip.zip onto the phone. Flashing took a bit longer than last time, but booting took no time at all. Thank you touch of jobo and usaff22, your advice was a lot of help.
touch of jobo said:
It can not find the local file. Make sure the file is not actually called 'ROM.zip.zip' (with 2x .zip ... you seem to have extensions hidden for most types but it shows .zip).
Click to expand...
Click to collapse
Ah, putting .zip.zip fixed that error, but has now given me a new one: protocol failure
touch of jobo said:
Which version of TWRP? I don't use it, but I read that the latest version has issues and you should use the previous version (2.2.0? I dont know).
Click to expand...
Click to collapse
TWRP v.2.3.3.0. Do you recommend an older build then, or do you think that CWM is a better tool for the job? (I have that on standby)
touch of jobo said:
Before flashing the zip, did you format your system, data, cache partitions?
Click to expand...
Click to collapse
I haven't done that again... Should I do that again? All that is on the system is the boot.img and the CM10.zip folder

kylepont said:
Ah, putting .zip.zip fixed that error, but has now given me a new one: protocol failure
Click to expand...
Click to collapse
I can't help with that adb error. Never seen it. Try searching the forums for it. Sorry. Also, I don't use Windows, so I don't know about driver versions and things.
kylepont said:
TWRP v.2.3.3.0. Do you recommend an older build then, or do you think that CWM is a better tool for the job? (I have that on standby)
Click to expand...
Click to collapse
TWRP and CWM are both fine for flashing ROMs, just not this specific version of TWRP. Since I dont use it myself, I dont know the exact version numbers, but read around a bit and you'll find what worked for others.
Maybe flashing a different recovery will even get rid of your protocol error.
If you've made nandroid backups (I guess you havent or we wouldnt be here.. sorry) you should stay with the same recovery (same 'brand', not same version) or you can't restore them.
kylepont said:
I haven't done that again... Should I do that again? All that is on the system is the boot.img and the CM10.zip folder
Click to expand...
Click to collapse
The CM10.zip should be on your sdcard, not your system partition. You dont need the boot img at all on your device. You need it on your PC in order to fastboot flash it.
Before flashing a ROM you should wipe your 'system', 'data', and 'cache' partitions, but not your 'sdcard' partition. Only if you flash (a newer version of) the same ROM you have operational, then you can sometimes flash without wiping. This is called 'dirty flashing'. But this does not apply in your case.

Successful flash of CyanogenMod, thanks for the help.
I would like to thank touch of jobo and usaff22 for their help, I just hope that somebody else will see this thread and get all of the answers that they need.

Re: [Q] Soft Brick... Can't install ROMS and pushing does not work.
kylepont said:
I would like to thank touch of jobo and usaff22 for their help, I just hope that somebody else will see this thread and get all of the answers that they need.
Click to expand...
Click to collapse
I would rename the zip to something else like sense.zip, place it on the desktop and do adb push C:\Users\username\Desktop\sense.zip /sdcard/
Make sure you use backward slashes for the PC file location, and forward slashes for the phone paste location.
This way we are also providing the full path on the PC.
Also make sure you use the latest adb from the SDK website. You don't need the whole thing, just the platform-tools bit, and replace the files in the new folder with the old one.
Sent from my One S using Tapatalk 2

Oh, while you're here, another problem has come about. Mounting the SD card will not work, and I can't replace it with a new SD card because... Well, there is no removable cover. I know how to fix it, I've read enough on here to find that out, but the only thing that I am missing is a stock recovery image for the S4 version (CID is ORANG001 if that is required) so if anybody knows a link for this then that will be greatly appreciated.

kylepont said:
Oh, while you're here, another problem has come about. Mounting the SD card will not work, and I can't replace it with a new SD card because... Well, there is no removable cover. I know how to fix it, I've read enough on here to find that out, but the only thing that I am missing is a stock recovery image for the S4 version (CID is ORANG001 if that is required) so if anybody knows a link for this then that will be greatly appreciated.
Click to expand...
Click to collapse
You might be able to find an RUU lying around on one of the websites which give RUUs such as androidfiles.org/ruu
I tried looking, but no sign of an orange RUU. An easy way to overcome this would be to change your CID to HTC__001 and use an unbranded RUU.

kylepont said:
the only thing that I am missing is a stock recovery image for the S4 version (CID is ORANG001 if that is required)
Click to expand...
Click to collapse
You can extract the recovery image from any RUU or OTA. Recoveries do not depend on carrier.
But .. if you can see your sdcard from within recovery (when 'choosing' a zip to flash, or from an adb shell or so) and from within Android, then you do not have The Unmountable Sdcard Issue and you should not go through that process. Only if you get an 'Unable to mount /sdcard' error in recovery.

touch of jobo said:
If you can see your sdcard from within recovery (when 'choosing' a zip to flash, or from an adb shell or so) and from within Android, then you do not have The Unmountable Sdcard Issue and you should not go through that process. Only if you get an 'Unable to mount /sdcard' error in recovery.
Click to expand...
Click to collapse
So I just use the stock recovery of any RUU I can find lying around for the HTC One S?
usaff22 said:
I tried looking, but no sign of an orange RUU. An easy way to overcome this would be to change your CID to HTC__001 and use an unbranded RUU.
Click to expand...
Click to collapse
How do I change the CID? Because knowing me, I'll screw it up and brick it if that is possible.

kylepont said:
So I just use the stock recovery of any RUU I can find lying around for the HTC One S?
Click to expand...
Click to collapse
Yes. You can use the recovery image from any RUU or OTA.
But first make sure you need it. The stock recovery thing is only to fix the situation where your sdcard is unmountable and you get that error in recovery.
kylepont said:
How do I change the CID? Because knowing me, I'll screw it up and brick it if that is possible.
Click to expand...
Click to collapse
This is the thread: http://forum.xda-developers.com/showthread.php?t=1671643
It involves extracting, hex-editing, and flashing a critical part of your device. If you make the slightest mistake you have a brick. However, if you read carefully and double check every step, it's not difficult. Many have done it. Read the thread.
Once you have supercid, you may as well get s-off as well. (This is the thread: http://forum.xda-developers.com/showthread.php?t=2155135 ) That way you can always flash anything.
Whatever you decide to do, before you start on anything, read all the instructions to the end, so that you're sure you can complete the process before you start. Also, before you start any process, try to understand what each step does and why it is necessary. That may involve a lot of reading and searching, but that is a Good Thing in the end.

touch of jobo said:
Yes. You can use the recovery image from any RUU or OTA.
But first make sure you need it. The stock recovery thing is only to fix the situation where your sdcard is unmountable and you get that error in recovery.
Click to expand...
Click to collapse
It is unmountable. I tried CWM and TWRP to no avail. Also, I have HBOOT version 2.15 which I heard is a bugger to work with. Also, I got the ZIP file for the stock 4.1, and I read that the stock recovery is in the firmware folder, but I cannot access it. (https://www.dropbox.com/s/kyn9sb5x7gpd7fr/Picture2.png) Then, I tried to get to the CID, following the instructions that you gave me, and I didn't get very far (https://www.dropbox.com/s/g6ik0i3los7unde/Picture3.png)

[Q] What Options for Flashed TF300T?

I bought a used TF300T, 16GB
Unlocked
It has TWRP 2.4.4.0, JB 4.2 bootloader, and EnergyROM 3/28 10.6.1.8
Kernel 3.1.10-g59bc3cb
I was wondering if I should leave it alone, or restore it to factory. Is that even possible?
If I keep it as it is, how do I update?
I knew I should have bought a virgin Asus, lol.
Thanks for any info!

You can restore it to factory by flashing a stock Asus blob in recovery (I recommend using the 10.6.1.8 ROM since that was the last one on your tablet). It will wipe all data, including whatever's on the internal storage. Once you get that set up, flash the OTA updates incrementally to avoid issues (there are only two updates to flash). You just have to download them (one at a time) and put them in /sdcard/ (that's where you start upon opening the file manager) -- be sure to unzip the downloaded file once, so you end up with another zip, and don't unzip that one. Reboot, and the tablet should notify you of an update. Repeat for the second update, and you should be exactly where you want to be.
All the blobs you need should be on Asus' website. If you need more help, there are lots of "how to flash back to stock" threads with instructions. Just read carefully, and if you decide to flash a custom recovery when you're done, DO NOT flash one with "-JB" at the end of it or you could brick your tablet. You will need a recovery that ends in "-42". Be absolutely sure, because there are 3 different bootloaders for the TF300, and flashing one from either of the other bootloaders will brick your tablet.

EndlessDissent said:
...You just have to download them (one at a time) and put them in /sdcard/ (that's where you start upon opening the file manager) -- be sure to unzip the downloaded file once, so you end up with another zip, and don't unzip that one. Reboot, and the tablet should notify you of an update. Repeat for the second update, and you should be exactly where you want to be...
Click to expand...
Click to collapse
That isn't doing anything. Is it because I have TWRP? Should I flash from TWRP?
Oh, I couldn't find the exact restore thread for my tablet
Perhaps you could point me?
Thanks again!

skank_boy said:
That isn't doing anything. Is it because I have TWRP? Should I flash from TWRP?
Oh, I couldn't find the exact restore thread for my tablet
Perhaps you could point me?
Thanks again!
Click to expand...
Click to collapse
That part of the instructions requires the stock recovery, which you should have if you flashed the stock blob as per the first sentence.

EndlessDissent said:
That part of the instructions requires the stock recovery, which you should have if you flashed the stock blob as per the first sentence.
Click to expand...
Click to collapse
Okay, I will try again. Maybe three times the charm. Thanks!

skank_boy said:
Okay, I will try again. Maybe three times the charm. Thanks!
Click to expand...
Click to collapse
You've flashed the stock blob in TWRP twice already? You're not flashing TWRP afterwards, are you? I've flashed a stock blob in TWRP, and I had the stock recovery afterwards. Are you rebooting into Android after you flash it?

I tried to flash, it failed....BUT this time it worked (??!!) lol.
Obviously I wasn't doing something right, but I have now. I installed 10.6.1.8, now on to the next in the normal manner.
Thanks again!

(Solved) Soft-bricked, but unable to flash anything but CWM.

Hello, I seem to have soft bricked my tf700.
​I flashed a newish pacman nightly in CWM (after wiping data/cache/dalvik cache), which completed with no errors, then I flashed the corresponding GAPPS. But my device became stuck in the pacman boot intro.
​So I tried flashing slimkat which led to my device not getting past the first bootup screen (where you can enter recovery if pressing the corresponding buttons).
​After this screw-up I stupidly hit the wipe data button on the bootloader. I then tried doing the method of using fastboot to erase system, cache, and all that so I could flash system blob of the newest asus US SKU (that is correct for a US bought tf700 right?). Either this or wiping the data caused me to have a different bootloader as pictured below as I no longer have the android button and it does not ask me to press volume up to access recovery (the only way to access recovery is by hitting the wipe data button in bootloader).
​I can still fastboot flash CWM, but trying to flash TWRP does not work as it finishes but going into recovery causes the tablet to just restart. Trying to flash asus stock as above would always give me an error like the one pictured below. Similar errors occur if trying to flash any rom inside CWM via an external sd card.
​I do not have access to adb as i believe i dont have usb debugging enabled since the pacman rom or any other rom did not ever start. It just gives me the device not found error even after manually installing the drivers on two different computers.
Cant seem to get these pics to load, but copying the url and pasting it works.
http://imgur.com/AaU0GMt
http://imgur.com/vDTVa4B

You probably flashed the wrong Rom. Try flashing the >right< stock Rom and go from there. Double check everything you flash.

tylerleo said:
You probably flashed the wrong Rom. Try flashing the >right< stock Rom and go from there. Double check everything you flash.
Click to expand...
Click to collapse
Whats the "right" rom here? Talking about the original asus stock rom? I have now tried the the pacman nightly, pacman release, slim kat release, clean rom release, an ICS asus stock rom, and two different versions of the jellybean asus stock rom. These were either done in CWM via internal sd card, external sd card, or done through fastboost flash system blob and flash zip.

gio3505 said:
Whats the "right" rom here? Talking about the original asus stock rom? I have now tried the the pacman nightly, pacman release, slim kat release, clean rom release, an ICS asus stock rom, and two different versions of the jellybean asus stock rom. These were either done in CWM via internal sd card, external sd card, or done through fastboost flash system blob and flash zip.
Click to expand...
Click to collapse
Whatever Rom came on the device,(Good thing to have, da) I'm not familiar with this device.

tylerleo said:
Whatever Rom came on the device,(Good thing to have, da) I'm not familiar with this device.
Click to expand...
Click to collapse
As far as i know, i have installed the stock rom, or atleast multiple versions of it with no success as it gives me an error stating something like staging or system when trying to write it.

gio3505 said:
As far as i know, i have installed the stock rom, or atleast multiple versions of it with no success as it gives me an error stating something like staging or system when trying to write it.
Click to expand...
Click to collapse
Hmm, I'd Download a stock Rom for the device offline, take on the sd card and put it on there real quick and try to flash that, if not, you probably bricked your device. I wouldn't know how to fix it beyond that. Ask the dev that made the Rom were everything that went south and an email to cwm wouldn't hurt either

I am also not sure if I need to have my external sd card formatted a certain way or download a specific CWM to allow flashing the stock rom. Ive spent over 10 hours trying to figure this out, very frustrating.

I have run CWM 6.0.4.6, CWM 6.0.4.7, and older versions to see if I could flash the stock rom with no luck. I have also tried different versions of TWRP but they always hang and reboot my tf700. I get errors ranging from status 6, status 7, cannot mount data, cannot mount staging, and cannot mount system. I am completely lost on what I can do. I have even tried a seperate sdcard to see if maybe the one I was originally using was bad with no luck. GG :/

gio3505 said:
I have run CWM 6.0.4.6, CWM 6.0.4.7, and older versions to see if I could flash the stock rom with no luck. I have also tried different versions of TWRP but they always hang and reboot my tf700. I get errors ranging from status 6, status 7, cannot mount data, cannot mount staging, and cannot mount system. I am completely lost on what I can do. I have even tried a seperate sdcard to see if maybe the one I was originally using was bad with no luck. GG :/
Click to expand...
Click to collapse
You gotta stop flashing stuff and slow down!
During all of this you never posted your bootloader version, so you may have been on the wrong bootloader to begin with - who knows.
When you hit the Wipe Data in the bootloader menu you caused the BL do write a wipe data command to the misc partition, causing the tablet to boot to recovery each time you booted (I'm guessing here) and then interrupting it. Usually, with CWM installed, it eventually sorts it out and executes the wipe data command, but that takes hours! You just have to leave it alone.
Hard to tell where you are now since you flashed all kinds of stuff since then.
Can you still boot into the bootloader and have a fastboot connection?
What's the BL version number?
If you boot, what does it boot into?
The picture links are broken - at least in Tapatalk. Post them again?

berndblb said:
You gotta stop flashing stuff and slow down!
During all of this you never posted your bootloader version, so you may have been on the wrong bootloader to begin with - who knows.
When you hit the Wipe Data in the bootloader menu you caused the BL do write a wipe data command to the misc partition, causing the tablet to boot to recovery each time you booted (I'm guessing here) and then interrupting it. Usually, with CWM installed, it eventually sorts it out and executes the wipe data command, but that takes hours! You just have to leave it alone.
Hard to tell where you are now since you flashed all kinds of stuff since then.
Can you still boot into the bootloader and have a fastboot connection?
What's the BL version number?
If you boot, what does it boot into?
The picture links are broken - at least in Tapatalk. Post them again?
Click to expand...
Click to collapse
Yes, the pictures are broken. You can still copy paste the url though. Couldnt figure out why it wouldnt work.
The tablet boots into the first screen that states it is unlocked, but does not go any further.
There is no bootloader version on the top left when holding down power + volume down.
I can still get to the place where it allows me to wipe data or fastboot, but the android icon to boot into android is now gone.
adb does not recognize my device even after manually installing the drivers, but fastboot works fine.
Is there any other way to find my bootloader version?

gio3505 said:
Yes, the pictures are broken. You can still copy paste the url though. Couldnt figure out why it wouldnt work.
The tablet boots into the first screen that states it is unlocked, but does not go any further.
There is no bootloader version on the top left when holding down power + volume down.
I can still get to the place where it allows me to wipe data or fastboot, but the android icon to boot into android is now gone.
adb does not recognize my device even after manually installing the drivers, but fastboot works fine.
Is there any other way to find my bootloader version?
Click to expand...
Click to collapse
Maybe you want to edit your post with the urls then.... Makes it easier for people trying to help...
You're seriously messed up, I think. I see a USB icon in there which would indicate that your bootloader is ancient. But then it says: "starting USB fastboot protocol".
Is that after you selected the USB icon?
Anyway, I think you're only chance is buster99's method to get it back. Did you try that already?
http://forum.xda-developers.com/showpost.php?p=44244313&postcount=12
Naturally you have to extract the system blob from the 10.6.1.14.10 US Asus firmware, but then you can try to fastboot flash it with buster's method.
Good luck!

berndblb said:
Maybe you want to edit your post with the urls then.... Makes it easier for people trying to help...
You're seriously messed up, I think. I see a USB icon in there which would indicate that your bootloader is ancient. But then it says: "starting USB fastboot protocol".
Is that after you selected the USB icon?
Anyway, I think you're only chance is buster99's method to get it back. Did you try that already?
http://forum.xda-developers.com/showpost.php?p=44244313&postcount=12
Naturally you have to extract the system blob from the 10.6.1.14.10 US Asus firmware, but then you can try to fastboot flash it with buster's method.
Good luck!
Click to expand...
Click to collapse
Its starts the usb fastboot automatically if no input is selected. I had a different bootloader up until i tried that thing that buster did. It always gives me an error like cant write to system or something if i try it.

gio3505 said:
Its starts the usb fastboot automatically if no input is selected. I had a different bootloader up until i tried that thing that buster did. It always gives me an error like cant write to system or something if i try it.
Click to expand...
Click to collapse
Which blob did you flash with buster's method?
I'm afraid you flashed something totally incompatible with your tablet...
You did not generate your nvflash blobs sometime prior to this, did you?

berndblb said:
Which blob did you flash with buster's method?
I'm afraid you flashed something totally incompatible with your tablet...
You did not generate your nvflash blobs sometime prior to this, did you?
Click to expand...
Click to collapse
I flashed the asus stock rom downloaded from their website. The US version as it was bought in the US (right? 0.o). I hadnt heard of nvflash before trying to install a rom so i did not make a backup.

gio3505 said:
I flashed the asus stock rom downloaded from their website. The US version as it was bought in the US (right? 0.o). I hadnt heard of nvflash before trying to install a rom so i did not make a backup.
Click to expand...
Click to collapse
Are you sure you downloaded the correct firmware? For the TF700?
Do you still have the original zip you extracted the blob from?
Post the exact file name please.

berndblb said:
Are you sure you downloaded the correct firmware? For the TF700?
Do you still have the original zip you extracted the blob from?
Post the exact file name please.
Click to expand...
Click to collapse
US_epaduser10_6_1_14_10_UpdateLauncher (2)
or
US_epaduser_VER104425UpdateLauncher
or
US_epad_user_9_4_5_30_20120907_UpdateLauncher
Ive downloaded a lot of different versions from the asus website. The last one came from a forum post listing older firmware, which I have tried a lot of different ones.

gio3505 said:
US_epaduser10_6_1_14_10_UpdateLauncher (2)
or
US_epaduser_VER104425UpdateLauncher
or
US_epad_user_9_4_5_30_20120907_UpdateLauncher
Ive downloaded a lot of different versions from the asus website. The last one came from a forum post listing older firmware, which I have tried a lot of different ones.
Click to expand...
Click to collapse
You flashed all of those blobs???
In which order?
With what result?
Jeez - I think you're done for...
Sorry mate, but gotta catch some sleep now. Maybe somebody else has a bright idea...

berndblb said:
You flashed all of those blobs???
In which order?
With what result?
Jeez - I think you're done for...
Sorry mate, but gotta catch some sleep now. Maybe somebody else has a bright idea...
Click to expand...
Click to collapse
I flashed the newest one first, and it gave me one of those errors that wouldnt allow me to flash it, and i tried the others with the same result. So technically i didnt flash any of them. I have been able to flash some roms, but they wouldnt boot so i would be stuck where i was when i started.

gio3505 said:
I flashed the newest one first, and it gave me one of those errors that wouldnt allow me to flash it, and i tried the others with the same result. So technically i didnt flash any of them. I have been able to flash some roms, but they wouldnt boot so i would be stuck where i was when i started.
Click to expand...
Click to collapse
Right stop flashing random stuff - you have combinations of JB4.2.1, JB4.1.1 and ICS 4.0.3 just listed there.
Let me put a call out to @lj50036 who may be able to save you but if you have messed the bootloader up with no nvflash backups you are not going to be happy with the result. If you can still get to the bootloader screen then he can perform miraculous superhero acts and *maybe* save your device.

gio3505 said:
I flashed the newest one first, and it gave me one of those errors that wouldnt allow me to flash it, and i tried the others with the same result. So technically i didnt flash any of them. I have been able to flash some roms, but they wouldnt boot so i would be stuck where i was when i started.
Click to expand...
Click to collapse
Shoot me an email at [email protected]
We can use hangouts see if there is a solution to your issue ...
Thx Josh

[RESOLVED] HELP.. Boot Loop With TWRP and L install

Hi
Earlier I installed TWRP via Philz and that worked fine.
I then reset my phone and flashed Bigxie's Android L, again this worked fine.
I flashed the new radio for the same thread and that worked fine.
I then downloaded CF-Root from here:
http://download.chainfire.eu/363/CF-Root/CF-Auto-Root/CF-Auto-Root-hammerhead-hammerhead-nexus5.zip
Ran the Windows Batch file all seemed to go well. Bootloader was unlocked and the big red android appears on screen.
Phone booted back to TWRP, a script ran and then my phone started constantly booting the the TWRP screen.
All I'm getting is teamwin flashing up.
If I power off it goes back to this loop.
Any way I can get this working again ?
Not worried about any data.. I've got all I need backed up.
Thanks

albert_htc said:
Hi
Earlier I installed TWRP via Philz and that worked fine.
I then reset my phone and flashed Bigxie's Android L, again this worked fine.
I flashed the new radio for the same thread and that worked fine.
I then downloaded CF-Root from here:
http://download.chainfire.eu/363/CF-Root/CF-Auto-Root/CF-Auto-Root-hammerhead-hammerhead-nexus5.zip
Ran the Windows Batch file all seemed to go well. Bootloader was unlocked and the big red android appears on screen.
Phone booted back to TWRP, a script ran and then my phone started constantly booting the the TWRP screen.
All I'm getting is teamwin flashing up.
If I power off it goes back to this loop.
Any way I can get this working again ?
Not worried about any data.. I've got all I need backed up.
Thanks
Click to expand...
Click to collapse
dont use root toolkits.
flash the factory img via fastboot. then flash twrp again, flash a kernel that allows root, then flash the latest supersu.

Thanks for the reply.
Just want to claify to make sure I don't make it worse..
I've got the L image from Googles site, do I extract the factory.img from that ?
Then flash it using :
fastboot flash factory factory.img
Thanks

Think I may have made things worse..
I extracted the tgz file and while browsing double clicked the flash all batch file.
:silly: Not sure how the hell I clicked it twice.. but it's doing something.. .hopefully not killing my phone.
Any suggestions how I did myself out of this hole..

albert_htc said:
Think I may have made things worse..
I extracted the tgz file and while browsing double clicked the flash all batch file.
:silly: Not sure how the hell I clicked it twice.. but it's doing something.. .hopefully not killing my phone.
Any suggestions how I did myself out of this hole..
Click to expand...
Click to collapse
i dont think hitting it twice will do anything. but you might have to flash the img files separate, as in the flash-all is giving some ppl issues.

simms22 said:
i dont think hitting it twice will do anything. but you might have to flash the img files separate, as in the flash-all is giving some ppl issues.
Click to expand...
Click to collapse
Found out how I've managed to double click.. The trackpad on my laptop is playing up.
I'll have to remember to use a USB mouse with it.
The phone has just rebooted and is coming back up.
Thanks for the advise.. looks like it's working.
I'll start a new thread with a couple of follow up questions.
Thanks

simms22 said:
i dont think hitting it twice will do anything. but you might have to flash the img files separate, as in the flash-all is giving some ppl issues.
Click to expand...
Click to collapse
When doing this, is there any specific order to follow when flashing all the .img files separately? I am also getting errors stating recovery.sig and boot.sig are missing. Does installing separate also take care of this?

Jmurf said:
When doing this, is there any specific order to follow when flashing all the .img files separately? I am also getting errors stating recovery.sig and boot.sig are missing. Does installing separate also take care of this?
Click to expand...
Click to collapse
it appears that the flash-all is having issues and skipping. so by flashing them all individually, you will make sure to flash them all.