Database Info

[GUIDE] DXKP9 Asian Gingerbread Update

WARNING: Please read thorugh the whole post!!
Guide:
1. Flash DXKF1 (download & extract files first) using ODIN:
- Open ODIN check Re-Partition, Auto Reboot, F.Reset Time
- Click PIT button choose: latona_20110114.pit
- Shutdown phone
- Simultaneously click and hold Vol.Down+Home+Power buttons (Download Mode)
- Connect phone to PC via Data Cable. (make sure ID:COM box in Odin highlighted yellow)
- Click ODIN's Start button
- Wait for "PASS!" to appear on top left corner of ODIN
- After PASS! click reset button (Re-Partition should be unchecked)
- Click PDA button and choose: I9003DXKF1-REV08-ALL-low-CL1020446.tar.md5
- Click PHONE button and choose: MODEM_I9003DXKB2_REV_00_CL863799.tar.md5
- Click CSC button and choose: GT-I9003-CSC-MULTI-OLBKB2.tar.md5
- Click Start and wait for "PASS!"
2. After reboot do not setup just shutdown and enter Download Mode.
3. Flash DXKP9 as PDA through ODIN:
- Open ODIN
- Click PDA button and choose: I9003DXKP9_I9003OLBKP7_I9003DXKP7_HOME.tar.md5
- Conect phone to PC via Data Cable (make sure ID:COM box in Odin highlighted yellow)
- Click Start button and wait for "PASS!"
4. After reboot, shutdown
5. Simultaneously click and hold Vol.Up+Home+Power buttons to enter Recovery Mode
6. Using volume buttons choose "wipe cache partition" and pres Home button
7. Choose "wipe data/factory reset" and press Home button
8. Choose "reboot system now" and press Home button to Reboot the phone
9. Complete phone setup dialogue, and test everything: Wifi,2G,3G,Mail Notification,GPS.
10. DONE!!
Download:
http://hotfile.com/dl/134002692/7f75...7_XME.zip.html
Mirrors :
http://www.mediafire.com/?35hz2fkzaiklll3(Recommended)(180MB)(No Password)
http://www.multiupload.com/1PQLH31F3L
Download Size : 200.5 MB
Password : samfirmware.com
Feedback Thread
Credits: lohengrin04(He posted this guide, I just made minor changes.)
The purpose of this thread was to help those who needed help flashing DXKP9.
This guide should work with no problems
Some of you which after flashing the PIT file your phone wont respond(Means when turn on only vibration then black screen), just remove annd re-insert your battery a couple of times and it will work out fine
ENJOY!!

Thanks will update the download thread with this
Edit : Updated OP of DXKP9 with this thread
Thanks

rohit_rocks said:
Thanks will update the download thread with this
Edit : Updated OP of DXKP9 with this thread
Thanks
Click to expand...
Click to collapse
No problem

can anyone pls pls pls post resumable link for dxkf1 or any dx fw through which i can upgrade to dxkp9????? my net is s#itty and dcs so cant download through hotfile

Mirrors for I9003DXKF1 : http://www.multiupload.com/DBMOCN6VPV

@Crazbanditz: Your mediafire link is error. Please edit link with
Code:
http://www.mediafire.com/?35hz2fkzaiklll3
cix18 said:
can anyone pls pls pls post resumable link for dxkf1 or any dx fw through which i can upgrade to dxkp9????? my net is s#itty and dcs so cant download through hotfile
Click to expand...
Click to collapse
It is here
Code:
http://www.mediafire.com/?s8rw6qknkssjm82

Thread updated!! Thanks!!

No feedback for this?

have anyone try this???

Thread UPDATED!!

can i flash DXKP9 after flashing XXKPE?

christopher2018 said:
can i flash DXKP9 after flashing XXKPE?
Click to expand...
Click to collapse
You can flash.

I bricked my phone :-(
Hi, I was in KPH - Cranium v3. I follow the above instruction to flash the KF1.
But my phone was bricked right after the below steps. Anyway to 'rescue' it? Turn on / down vol+home+power / up vol+home+power only give a vibration and blank screen.
1. Flash DXKF1 (download & extract files first) using ODIN:
- Open ODIN check Re-Partition, Auto Reboot, F.Reset Time
- Click PIT button choose: latona_20110114.pit
- Shutdown phone
- Simultaneously click and hold Vol.Down+Home+Power buttons (Download Mode)
- Connect phone to PC via Data Cable. (make sure ID:COM box in Odin highlighted yellow)
- Click ODIN's Start button
- Wait for "PASS!" to appear on top left corner of ODIN
---------- Post added at 05:44 PM ---------- Previous post was at 05:29 PM ----------
Nevermind. After taken out battery for several times. I finally flashed to KF1. Thx.

sonyu2011 said:
Hi, I was in KPH - Cranium v3. I follow the above instruction to flash the KF1.
But my phone was bricked right after the below steps. Anyway to 'rescue' it? Turn on / down vol+home+power / up vol+home+power only give a vibration and blank screen.
1. Flash DXKF1 (download & extract files first) using ODIN:
- Open ODIN check Re-Partition, Auto Reboot, F.Reset Time
- Click PIT button choose: latona_20110114.pit
- Shutdown phone
- Simultaneously click and hold Vol.Down+Home+Power buttons (Download Mode)
- Connect phone to PC via Data Cable. (make sure ID:COM box in Odin highlighted yellow)
- Click ODIN's Start button
- Wait for "PASS!" to appear on top left corner of ODIN
---------- Post added at 05:44 PM ---------- Previous post was at 05:29 PM ----------
Nevermind. After taken out battery for several times. I finally flashed to KF1. Thx.
Click to expand...
Click to collapse
Sorry for the late reply. But yeah. Some of our phones, after flashing the PIT file would not respond for awhile. So yea, just remove and reinsert the battery a couple of times. AND TADA!!

where are the files for PDA, PHONE, CSC buttons. on extracting only one md5 file. should i use in PDA button what about pit file

acero2011 said:
where are the files for PDA, PHONE, CSC buttons. on extracting only one md5 file. should i use in PDA button what about pit file
Click to expand...
Click to collapse
Erm. All u gotta do is read my instructions clearly. It has all ur answers in it
Sent from my GT-I9003

If im alrdy on stocj dxkp1 i just start flashing dxkp9 over right? Its fresh out of the box, still charging, havent done anything to it yet
Sent from my GT-i5801 using XDA App

whats the difference between XXKPQ and DXKP9, are there any major changes?

Sorry for being inactive for a long time guys, I have been trying to finish my homework. I am only 13. So yea, guys, please post feedback about this method!! Thx!

Works
Cheers
Sent from my i9003 powered by Poseidon's Rom/Dxkp9 Junior + UC kernel

Samsung Galaxy SL Flash problem?

Samsung Galaxy SL Flash problem?
i have put .pit file using odin now my mobile wont start.i rooted my Galaxy sl and was trying to flash a rom by using this thread http://forum.xda-developers.com/showthread.php?t=1004622 but after 7th step i don't know what to do so i restart my phone and it wont start.please help

jagwant said:
Samsung Galaxy SL Flash problem?
i have put .pit file using odin now my mobile wont start.i rooted my Galaxy sl and was trying to flash a rom by using this thread http://forum.xda-developers.com/showthread.php?t=1004622 but after 7th step i don't know what to do so i restart my phone and it wont start.please help
Click to expand...
Click to collapse
After 7th step just switch off phone by pulling out battery. Then go to download mode & then start from 8th step. It is as simple as that. Dont worry

vishal24387 said:
After 7th step just switch off phone by pulling out battery. Then go to download mode & then start from 8th step. It is as simple as that. Dont worry
Click to expand...
Click to collapse
i am from india and i don't know which files to load in CSC,PDA Bootloader Phone
http://forum.xda-developers.com/showthread.php?t=1707712 i have downloaded this rom
can i just start my phone without flashing a new rom please help

jagwant said:
i am from india and i don't know which files to load in CSC,PDA Bootloader Phone
http://forum.xda-developers.com/showthread.php?t=1707712 i have downloaded this rom
can i just start my phone without flashing a new rom please help
Click to expand...
Click to collapse
I am also from India. In india DDLF2 rom is latest official firmware. Download DDLF2 rom from here.
http://forum.xda-developers.com/showthread.php?t=1741370

vishal24387 said:
I am also from India. In india DDLF2 rom is latest official firmware. Download DDLF2 rom from here.
http://forum.xda-developers.com/showthread.php?t=1741370
Click to expand...
Click to collapse
what about CSC,PDA,Bootloader,Phone files are they included in this rom
is there any that i can just start my phone without flashing a new rom please help

Look buddy u have to understand flashing procedure in detail. First you have to download XXKPE rom. Download XXKPE rom from here.
http://hotfile.com/dl/145780524/f7d1f45/I9003XXKPE.zip.html
Download odin software from here
forum.xda-developers.com/attachment.php?attachmentid=1254464&d=1344665129
Now follow following procedure
1. Unzip XXKPE firmware zip file.
2. Run Odin software.
3. Check Re-Partition, Auto Reboot and F. Reset
Time.
4. Click PIT button and select this file:
latona_20110114.pit
5. Set it to download mode : Press Volume
down + OK first, then hold Power button.
6. Connect USB cable and the program will
detect the phone's Com number.
7. Click Start button to download the PIT file to
phone.
8. After it is Done Click on Reset button
[Partition box should be unchecked
automatically]
9. Click PDA button and select this file:
CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click PHONE button and select this file:
MODEM_I9003XXKPE_REV_00_CL1041909.tar
11. Click BOOTLOADER button and select this
file:
APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
12. Click CSC button and select this file: GT-
I9003-CSC-MULTI-OXAKPE.tar
13: You should unplug usb cable, remove
battery, insert battery and bring it back to
download mode. I have never been able to
bring it to download mode with usb plugged in.
14. Click Start button to flash these files to
phone.
15. Do not touch anything till you see PASS on
the program window.
16. Factory reset
Click to expand...
Click to collapse
Now when ur phone will start u can see that XXKPE rom is flashed on ur phone successfully.
Now next step is to flash DDLF2 rom. Unzip DDLF2 zip file. You will get I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5 file having size nearly 300-350 mb. So just turn off phone & go to download mode again. Run odin & select this .md5 file in pda option & then flash it. Thats it buddy. When ur phone will turn on you will observe DDLF2 rom is flashed on ur phone

vishal24387 said:
Look buddy u have to understand flashing procedure in detail. First you have to download XXKPE rom. Download XXKPE rom from here.
http://hotfile.com/dl/145780524/f7d1f45/I9003XXKPE.zip.html
Download odin software from here
forum.xda-developers.com/attachment.php?attachmentid=1254464&d=1344665129
Click to expand...
Click to collapse
after that

jagwant said:
after that
Click to expand...
Click to collapse
See above post. I have given all steps.

vishal24387 said:
See above post. I have given all steps.
Click to expand...
Click to collapse
thanks i will this rom next morning.
but i have flashed this rom http://forum.xda-developers.com/showthread.php?t=1707712
now my phone is stuck in rebooting loop

jagwant said:
thanks i will this rom next morning.
but i have flashed this rom http://forum.xda-developers.com/showthread.php?t=1707712
now my phone is stuck in rebooting loop
Click to expand...
Click to collapse
Dont worry just do what I have said buddy

vishal24387 said:
Look buddy u have to understand flashing procedure in detail. First you have to download XXKPE rom. Download XXKPE rom from here.
http://hotfile.com/dl/145780524/f7d1f45/I9003XXKPE.zip.html
Download odin software from here
forum.xda-developers.com/attachment.php?attachmentid=1254464&d=1344665129
Now follow following procedure
1. Unzip XXKPE firmware zip file.
2. Run Odin software.
3. Check Re-Partition, Auto Reboot and F. Reset
Time.
4. Click PIT button and select this file:
latona_20110114.pit
5. Set it to download mode : Press Volume
down + OK first, then hold Power button.
6. Connect USB cable and the program will
detect the phone's Com number.
7. Click Start button to download the PIT file to
phone.
8. After it is Done Click on Reset button
[Partition box should be unchecked
automatically]
9. Click PDA button and select this file:
CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click PHONE button and select this file:
MODEM_I9003XXKPE_REV_00_CL1041909.tar
11. Click BOOTLOADER button and select this
file:
APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
12. Click CSC button and select this file: GT-
I9003-CSC-MULTI-OXAKPE.tar
13: You should unplug usb cable, remove
battery, insert battery and bring it back to
download mode. I have never been able to
bring it to download mode with usb plugged in.
14. Click Start button to flash these files to
phone.
15. Do not touch anything till you see PASS on
the program window.
16. Factory reset
Click to expand...
Click to collapse
Now when ur phone will start u can see that XXKPE rom is flashed on ur phone successfully.
Now next step is to flash DDLF2 rom. Unzip DDLF2 zip file. You will get I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5 file having size nearly 300-350 mb. So just turn off phone & go to download mode again. Run odin & select this .md5 file in pda option & then flash it. Thats it buddy. When ur phone will turn on you will observe DDLF2 rom is flashed on ur phone
Click to expand...
Click to collapse
i have done the same procedure on firnd's i9003, but next firmware was JPKPH[instead of DDLF2] 2.3.6,... with it's .tar.md5... now my friend is experiencing some cell signals drop, with call drop and sms sending fail..! any resolution for this..!!

Unable to install LF2

Hello friends,
I had been running LF2 for the past few months successfully but i had installed Frankenstein's Mod which i did not prefer over stock due to stability issues. Now when i reflashed LF2 with the PIT file, My device doesnt boot up and keeps restarting after showing the Samsung page. I had to install XXKPQ which is Serbian i suppose to successfully recover my device and it updated to LE4 via Kies.
I am having stability issues now with LE4 and extremely poor battery life.
Please can anybody guide me how do i get back my LF2 again so please tell me which ROM should i Flash before
Thank you!

ronak_143 said:
Hello friends,
I had been running LF2 for the past few months successfully but i had installed Frankenstein's Mod which i did not prefer over stock due to stability issues. Now when i reflashed LF2 with the PIT file, My device doesnt boot up and keeps restarting after showing the Samsung page. I had to install XXKPQ which is Serbian i suppose to successfully recover my device and it updated to LE4 via Kies.
I am having stability issues now with LE4 and extremely poor battery life.
Please can anybody guide me how do i get back my LF2 again so please tell me which ROM should i Flash before
Thank you!
Click to expand...
Click to collapse
If you want stability and battery life, perhaps XXKPQ is for you.. the best ROM in my opinion is XXKPQ and JPKPH
Sent from my GT-I9100 using xda premium

Ok guys i've found out the solution for those who want their default indian roms in their devices
DDKP1 with PIT->then DDKP3 with PIT->Install BAM kernel then connect to KIES to get LF2 easily

ronak_143 said:
Ok guys i've found out the solution for those who want their default indian roms in their devices
DDKP1 with PIT->then DDKP3 with PIT->Install BAM kernel then connect to KIES to get LF2 easily
Click to expand...
Click to collapse
That's great that you found it!
Sent from my GT-I9100 using xda premium

saywhatt said:
That's great that you found it!
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
Alas, it failed though. It does a factory reset every time i restart the phone Any suggestions how to repair this now

ronak_143 said:
Alas, it failed though. It does a factory reset every time i restart the phone Any suggestions how to repair this now
Click to expand...
Click to collapse
I think you need a clean install from scratch.
Here the guides on how to --> http://forum.xda-developers.com/showthread.php?t=1133787

ronak_143 said:
Ok guys i've found out the solution for those who want their default indian roms in their devices
DDKP1 with PIT->then DDKP3 with PIT->Install BAM kernel then connect to KIES to get LF2 easily
Click to expand...
Click to collapse
You will need following before beginning installation:
1) Flsher Program + PIT (ODIN3 + Latona.PIT)
2) Firmware: I9003XXKPE
3) Firmware: I9003DDLF2 (http://www.hotfile.com/dl/161660941/8fd61ef/I9003DDLF2_I9003ODDLF2_INU.zip.html)
STEPS:
1) Open ODIN. Connect ur phone in download mode. just flash Latona.PIT file with Re-Partition selected.
2) Once flashed, Ur phone will reboot automatically but will show only black screen with background light. Do not worry. Open the back cover, remove the battery, insert battery and boot again in download mode.
3) Close ODIN. Open it again. Now we will be installing XXKPE.
i) Select Latona.PIT File in ODIN. (Make sure the "Re-Partition" is unchecked once you have selected PIT file)
ii) Select "APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5" in bootloader.
iii) Select "CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5" in PDA.
iv) Select "MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5" in PHONE.
v) Select "GT-I9003-CSC-MULTI-OXAKPE.tar.md5" in CSC.
Now flash it.
this will successfully install XXKPE on ur device. Once your flash is complete, ur device will boot and will ask for initial config. U can set it or just power off ur device and boot again in download mode.
Now will install DDLF2.
i) Select Latona.PIT File in ODIN. (Make sure the "Re-Partition" is unchecked once you have selected PIT file)
ii) Just select "I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5" in your PDA and flash.
U are now on DDLF2.

pranshah said:
You will need following before beginning installation:
1) Flsher Program + PIT (ODIN3 + Latona.PIT)
2) Firmware: I9003XXKPE
3) Firmware: I9003DDLF2 (http://www.hotfile.com/dl/161660941/8fd61ef/I9003DDLF2_I9003ODDLF2_INU.zip.html)
STEPS:
1) Open ODIN. Connect ur phone in download mode. just flash Latona.PIT file with Re-Partition selected.
2) Once flashed, Ur phone will reboot automatically but will show only black screen with background light. Do not worry. Open the back cover, remove the battery, insert battery and boot again in download mode.
3) Close ODIN. Open it again. Now we will be installing XXKPE.
i) Select Latona.PIT File in ODIN. (Make sure the "Re-Partition" is unchecked once you have selected PIT file)
ii) Select "APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5" in bootloader.
iii) Select "CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5" in PDA.
iv) Select "MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5" in PHONE.
v) Select "GT-I9003-CSC-MULTI-OXAKPE.tar.md5" in CSC.
Now flash it.
this will successfully install XXKPE on ur device. Once your flash is complete, ur device will boot and will ask for initial config. U can set it or just power off ur device and boot again in download mode.
Now will install DDLF2.
i) Select Latona.PIT File in ODIN. (Make sure the "Re-Partition" is unchecked once you have selected PIT file)
ii) Just select "I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5" in your PDA and flash.
U are now on DDLF2.
Click to expand...
Click to collapse
Works perfectly Thank you!

[Q] Galaxy S i9003 stuck at boot loop!!

My Samsung Galaxy SL i9003 is bricked. My Phone enters into both Recovery and Download Mode. I have tried to flash phone with I9003XXKPQ as mentioned in steps given in Misledz's Thread http://forum.xda-developers.com/showthread.php?t=1133787 . But, its not working for me.
Can you suggest me what firmware should i try? I am new here so could anyone help me on this, Please?

Your phone's not bricked since you can still go to download mode.. go to download mode and flash a firmware the stock one
Sent from my GT-I9300 using xda premium

saywhatt said:
Your phone's not bricked since you can still go to download mode.. go to download mode and flash a firmware the stock one
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
Which version of stock firmware would you suggest? I just want my Phone back to life.

amritunsung said:
Which version of stock firmware would you suggest? I just want my Phone back to life.
Click to expand...
Click to collapse
If you have read Misledz's thread thoroughly in the first place you should be ok...try XXKPE

wee2wee said:
If you have read Misledz's thread thoroughly in the first place you should be ok...try XXKPE
Click to expand...
Click to collapse
I have 1). Flashed with XXKPE including latona.pit file.. (Failed.. Still rebooting).
2). Flashed with XXKPE and then flashed with XXKPQ.. (Failed.. Still rebooting)

amritunsung said:
I have 1). Flashed with XXKPE including latona.pit file.. (Failed.. Still rebooting).
2). Flashed with XXKPE and then flashed with XXKPQ.. (Failed.. Still rebooting)
Click to expand...
Click to collapse
Set your phone to "download" mode, connect phone to computer..Run Odin3_v3.04...click "PIT" only, select "latona_20110114.pit" click start..after finished, phone will turn screen off..
Take out your battery and put it back after a few seconds, go to download mode again, start Odin3_v3.04,
1. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
2. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
3. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
4. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar ...click start..wait for it to finish...disconnect from computer..your phone will reboot itself
If you want to install new update/value pack, I used DDLF2(get it here: http://forum.xda-developers.com/showthread.php?t=1004647)...go to download mode, connect your phone to the computer,start Odin3_v3.04,select/click pda..look for the "I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar"..click start..wait for it to finish...disconnect from computer..your phone will reboot itself...

wee2wee said:
Set your phone to "download" mode, connect phone to computer..Run Odin3_v3.04...click "PIT" only, select "latona_20110114.pit" click start..after finished, phone will turn screen off..
Take out your battery and put it back after a few seconds, go to download mode again, start Odin3_v3.04,
1. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
2. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
3. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
4. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar ...click start..wait for it to finish...disconnect from computer..your phone will reboot itself
If you want to install new update/value pack, I used DDLF2(get it here: http://forum.xda-developers.com/showthread.php?t=1004647)...go to download mode, connect your phone to the computer,start Odin3_v3.04,select/click pda..look for the "I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar"..click start..wait for it to finish...disconnect from computer..your phone will reboot itself...
Click to expand...
Click to collapse
Did as you said, but same problem still exists. Is this due to any hardware problem? I have read from other users about it as it maybe a Motherboard issue.

Bootloader & PDA
I need to download PDA- CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar & BOOTLOADER- APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar but i m tired of searching these two files. plz can anyone give me the link to download these?

aurtho09 said:
I need to download PDA- CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar & BOOTLOADER- APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar but i m tired of searching these two files. plz can anyone give me the link to download these?
Click to expand...
Click to collapse
follow z3x site you will gat it .

[Q] Downgrade to DDLF2 from cm10A3

Hi, I am on cm10 alpha 3, and i want to go back to gingerbread ddlf2 value pack, as described in http://forum.xda-developers.com/showthread.php?t=2174127&highlight=odin.
I gone to download mode, and flash latona_20110114.pit file in pit in odin, and when odin finished, phone can't start, just show black screen (little brighter then when is off). After removing battery i managed to go to download mode, but don't know now what. Can pleas someone help me!

osamslova said:
Hi, I am on cm10 alpha 3, and i want to go back to gingerbread ddlf2 value pack, as described in http://forum.xda-developers.com/showthread.php?t=2174127&highlight=odin.
I gone to download mode, and flash latona_20110114.pit file in pit in odin, and when odin finished, phone can't start, just show black screen (little brighter then when is off). After removing battery i managed to go to download mode, but don't know now what. Can pleas someone help me!
Click to expand...
Click to collapse
This is how you do it. go make some hot coffee, a pack of cigarette if you smoke, and some cookies and then do the following:
1. get the firmware ready. it is advisable using XXKPE as base.
2. run Odin3 v1.83
3. click Re-Partition, Auto Reboot and F. Reset Time.
4. press PIT and choose file: latona_20110114.pit
5. on your phone; go to download mode : press Volume down + Home (middle button), and power. (hold until you saw the green robot )
6. connect USB cable to your SL, wait until its connected you can check it in Odin.
7. click start
8. when its done, press reset [Partition box will automatically not selected] your SL will go blank (its ok its normal)
9. pull your SL from cable, open its battery, put it on again, and go back to download mode like on step #5 and reconnect is cable to SL until connected.
10. press BOOTLOADER choose file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
11. press PDA, choose file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
12. press PHONE, choose file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
13. click CSC choose file: GT-I9003-CSC-MULTI-OXAKPE.tar
14. click start
15. dont touch anything until its done. (its a perfect time to drink that coffee & eat some cookies while you wait)
16. if its done your SL will reboot by itself and start the first boot.
17. do a Factory reset by pressing *2767*3855#
18. most FW GB needed to be flashed at least twice. so you need to flash it again. all you need to do just repeat step 10 -16, for the second flash, there is no need to flash latona_20110114.pit again.
19. after your XXKPE up and running. turn it off again. go to download mode & flash DDLF2 you only need to put DDLF2 file into PDA and click start to update from XXKPE to DDLF2 no need to flash bootloader/phone/csc again.
20. after its done. your SL will automatically rebooted again into DDLF2
Enjoy! cheers. simple thanks wont hurt! :good:
WARNING!!: Re-Partition only selected during latona.pit. if you got into step No.9, make sure Re-Partition not selected. :victory: