I just picked up a used LG O3D P925 that has no connection to any network (well wifi works). When I tried to update using the LG mobile update tool. I had a no success detecting automatically so I clicked recovery and manually entered the IMEI and S/N. Soon I got a failure error. Prior to this I read a thread about OTA firmware updates but I have no button for OTA update.
I tried rooting using megatron (windows version) and installed the LG drivers but windows keeps detecting new hardware and wants me to install drivers. When I click run it just says "daemon started" and I wait for a couple of minutes and .... nothing. When I check the apns either none are listed or I get a message about "reorganizing internal processes. please try again later " ...
I contacted someone who had their phone replaced by carrier for same issue. Possibly the carrier has blocked the phone from network? ...O I hope not
.... Help !?
is it a stock rom goto play store dl get ril what does it say. sounds like bad based band
Post-:
Rom:
Baseband:
RIL:
GetRIL says "unknown RIL found" (gives me an md5sum)
for Baseband it says XMM6360
then there are 3 options to DL but since I don't have root I am unable to DL these updates ... says " no permission".
here is the info from about:
LG- P925g
Android Version 2.2.2
Baseband Version L6260_MODEM_SIC_01.1042.00
Kernal Version 2.6.35.7
Build number FRG83G
Software Version LGP925g-V10c-JUL-20-2011
ok I have succeeded getting root using Unlock Root. Now when I open getRIL and select a RIL to DL the "ok" button is "greyed out" or not available, just the cancel button. So after I cancel and select another RIL to DL & install I get the superuser permisson granted message followed by a message that says "The system partition needs to be writable.... and back to the greyed out ok and cancel choice.
vumanizer said:
GetRIL says "unknown RIL found" (gives me an md5sum)
for Baseband it says XMM6360
then there are 3 options to DL but since I don't have root I am unable to DL these updates ... says " no permission".
here is the info from about:
LG- P925g
Android Version 2.2.2
Baseband Version L6260_MODEM_SIC_01.1042.00
Kernal Version 2.6.35.7
Build number FRG83G
Software Version LGP925g-V10c-JUL-20-2011
Click to expand...
Click to collapse
I see imei could have been damaged uhm try updating to V20C see if it helps
How to Update
Offline Update
V20C_00.kdz
Megatron Root
Recovery
if you do this and still no network try This its for LG Optimus Black but may work on p925g. Also Make sure phone not in airplane mode.
Thanks for your help decomfg .
I tried flashing but it seems I'm still having trouble with this computer recognizing this device. Here is the log file:
[R&D Test Tools Log File]
18:04:24 : Start fn_StartUpgrade
18:04:24 : Extract kdz file
18:05:26 : kdz decrypt Success
18:05:38 : Extract file Success.
18:05:38 : LGMobileDL Load.
18:05:38 : Port = -1
18:05:38 : Connection check start.
18:05:38 : Port(or Device) Not Found!
18:05:40 : Finish All test
when you try to flash the kdz do u put the phone in download mode try this guide
http://forum.xda-developers.com/showthread.php?t=1491870
you want part 3
xstokerx said:
when you try to flash the kdz do u put the phone in download mode try this guide
http://forum.xda-developers.com/showthread.php?t=1491870
you want part 3
Click to expand...
Click to collapse
I seem to get hung up on the step where you check the device manager for current active "COM" ports. When I connect the USB (holding vol up + power) I get OMAP4430 appearing for a second under ports and I get the "windows has detected new hardware" flashing on and of simultaneously. The phone doesn't seem to want to boot into download mode and it doesn't vibrate after 3 seconds.
vumanizer said:
Thanks for your help decomfg .
I tried flashing but it seems I'm still having trouble with this computer recognizing this device. Here is the log file:
[R&D Test Tools Log File]
18:04:24 : Start fn_StartUpgrade
18:04:24 : Extract kdz file
18:05:26 : kdz decrypt Success
18:05:38 : Extract file Success.
18:05:38 : LGMobileDL Load.
18:05:38 : Port = -1
18:05:38 : Connection check start.
18:05:38 : Port(or Device) Not Found!
18:05:40 : Finish All test
Click to expand...
Click to collapse
Delete All Lg Drivers and Software Run CCleaner and clean registry then reinstall LG PC Suite IV
CCleaner
PC Sync
On The Phone Goto Settings/Applications/Debugging/ Make sure ADB is ticked and then try flash it again try a diff usb port also make sure its not plugged into a usb hub. if it fails again i think the problem is with pc not the phone
Try connect device without battery and with holding vol up. Then after device is connected (wait 20 sec wile holding vol up) reinsert battery and start update.
Sent from my LG-P920 using XDA
if it keeps connecting and the disconneting try this. attach usb cable to PHONE only then take your battery out, then put battery back in and quickly press volume up button and then attach usb cable to PC. keep hold of volume up button all time dont let go and install all drivers omap, usb driver etc.
hope it helps
I have managed to make things worse ... :crying:
Now my phone is stuck on the AT&T boot screen. The only way I can power off is to remove the battery.Yes I tried flashing the v20P kdz after I thought I could do much worse.
I no longer have a problem getting my computer to recognize the drivers. I'm not sure if I flashed the v20C kdz without a problem or not. I thought I was able to root and things were ok except that I still had no network connectivity. I don't recall exactly what I tried next but I think I lost root somehow and some of the installed apps began misbehaving. I also noticed that superuser was not installed. I tried to root again but couldn't. I treid to flash a kdz again but again not very successfully. I also tried repairing the IMEI using this guide http://forum.xda-developers.com/showthread.php?t=1734330
I flashed the CP ? but didn't manage to restore the imei.
Now I when I power on I get the AT&T animation ... I tried to flash back to the 20C kdz without and luck. Now I have no idea where to go from here and would be grateful for some input.
try updating again but let the process fully complete http://forum.xda-developers.com/showthread.php?t=1244490
If you were stuck on the art boot screen after flashing v20p you should have don't a hard reset and wiped all data. I had the same issue when going from v10k to v20p. As far as the no signal goes I'm not sure but it could be a bad radio or it could have been stolen and deactivated by AT&t
Sent from my LG-P925 using Tapatalk 2
Related
If you did something like install custom recovery on your lg optimus one and failed, you would get a black screen saying..
fastboot mode started
udc_start()
If this happens...
Relax.. Your phone is not bricked.. There are many ways to fix it... This method of unbricking should be done as a last resort because it erases all your data...
Charge your phone before proceeding even if the backlight is always on while charging..
Things required:
Kdz updater:
http://forum.xda-developers.com/showpost.php?p=8651505&postcount=1
Stock ROM:
http://forum.xda-developers.com/showthread.php?t=865479
USB cable, Windows PC with administrator account,LG united mobile drivers(google for it if you don't find it in the "Add or remove programs" window in the control panel)..
First disable all LGE modems under modems from Windows device manager in the Control Panel..
Make sure you have LG united mobile drivers installed.. Or just google for it..
Then press and hold both the back(return) button and the volume up button and simultaneously connect the USB cable..
The phone should light up and say Emergency mode!! in a green background.. If it goes to Emergency mode, it can be fixed... If it doesn't I'm sorry, search for an other forum or give it to the LG service center...
Now decompress the 7z file you downloaded using WinZip, WinRar etc., install msxml.msi from the uncompressed directory and run KDZ_FW_UPD.exe (With administrator rights by right clicking and selecting run as administrator).
In the dialog box, select Type : 3GQCT and PhoneMode: DIAG, select the kdz file and flash the stock ROM... It would take about 15 minutes.. If the kdz updater crashes, change compatibility mode or restart the computer and phone or do something till it works (Retry retry retry)...
For most of you it would probably say PHONE WAS NOT FOUND!.... If so, then follow all the steps said above, but this time, shake the life out of your phone after connecting the USB till the lines "PHONE WAS NOT FOUND!" stops appearing... If it does appear again retry for endless times or restart the computer or check if any modem drivers are active or try it in an another computer...
From here on, follow any one choice:
Choice 1:
Note: There is a fat chance for this choice to not work and for you to go back to the very first line of this thread...
If you want your phone to have all the data before you bricked it, just disconnect the USB when the phone shows the charge screen as if you are charging the phone while it is switched off.. (This was discovered accidentally by me so try it at your own risk ) After disconnecting try to power on the normal way and it should work and the phone should be like it was never bricked.. If it doesn't boot, retry flashing from the start.. If it starts and all your data is restored root it, install titanium backup and backup all your apps and data and save the contents of sdcard\titaniumbackup to your pc.. Then copy all you want in your sdcard to your pc.. Then redo all the steps without disconnecting till the kdz flasher says FINISHED.. This is because if you disconnect the usb in the middle, only half the rom would be installed which is unstable.. After installing the full rom, root it, and install titanium backup and copy all the copied content back to sdcard\titaniumbackup and restore them using titanium backup.. That's it..
Choice 2:
If you do not want the data and if you need to do a risk-free unbrick, then flash with the kdz updater and wait till it says FINISHED.. That's it..
Now that you know how to unbrick, try installing what bricked your phone again but this time in the correct way... GOOD LUCK...
AND FINALLY.... ONE MORE STEP.... PRESS THE "THANK" BUTTON IF I HELPED YOU IN ANY WAY...
where do you get kdz?
ljohnson1981 said:
where do you get kdz?
Click to expand...
Click to collapse
Links have been included...
ganesh3s3 said:
If you did something like install custom recovery on your lg optimus one and failed, you would get a black screen saying..
fastboot mode started
udc_start()
If this happens...
Relax.. Your phone is not bricked.. There is a way to fix it...
First disable lg modem from windows device manager..
Make sure you have lg universal driver installed.. Or just google for it..
Charge your phone before proceeding even if the backlight is always on..
Things required:
Kdz updater:
forum.xda-developers.com/showpost.php?p=8651505&postcount=1
Stock rom:
forum.xda-developers.com/showthread.php?t=865479
Usb cable, windows pc
Then press and hold both the back(return) button and the volume up button and simultaneously connect the usb cable..
The phone should light up and say Emergency mode!! in a green background..
Then decompress the 7z, install msxml.msi from the uncompressed directory and run KDZ_FW_UPD.exe (Has administrator).
Select Type : 3GQCT and flash the stock rom... It would take about 15 minutes.. If the kdz updater crashes, change compatibility mode or restart or do something till it works...
If you want your phone to have all the data before you bricked it, just disconnect the usb when the phone shows the charge screen as if you are charging the phone while it is switched off.. (This was discovered accidentally by me so try it at your own risk) After disconnecting try to power on the normal way and it should work and the phone should be like it was never bricked.. If it doesn't boot retry flashing from the start.. If it starts and all your data is restored root it, install titanium backup and backup all your apps and data and save the contents of sdcard\titaniumbackup to your pc.. Then copy all you want in your sdcard to your pc.. Then redo all the steps without disconnecting till the kdz flasher says FINISHED.. This is because if you disconnect the usb in the middle, only half the rom would be installed which is unstable.. After installing the full rom, root it, and install titanium backup and copy all the copied content back to sdcard\titaniumbackup and restore them using titanium backup.. That's it..
If you do not want the data and if you need to do a riskfree unbrick, then flash with the kdz updater and wait till it says FINISHED.. That's it..
Now that you know how to unbrick it, try installing what bricked your phone again but in the correct way... GOOD LUCK...
THANK ME IF I HELPED YOU...
Click to expand...
Click to collapse
i tried this but got msg:
[R&D Test Tools Log File]
12:20:25 : Launching SW update
12:20:25 : Unpacking KDZ
12:20:31 : KDZ file extraced
12:20:32 : Files were extracted.
12:20:32 : LGMobileDL Load.
12:20:32 : Port = 3
12:20:32 : Connecting to phone
12:20:37 : PHONE WAS NOT FOUND!
12:20:39 : ===FINISHED===
what to do????? i am using xp64....... what do you mean by (Has administrator).
Please help or i to go LG service center???
Thanks in advance
maxupload said:
i tried this but got msg:
[R&D Test Tools Log File]
12:20:25 : Launching SW update
12:20:25 : Unpacking KDZ
12:20:31 : KDZ file extraced
12:20:32 : Files were extracted.
12:20:32 : LGMobileDL Load.
12:20:32 : Port = 3
12:20:32 : Connecting to phone
12:20:37 : PHONE WAS NOT FOUND!
12:20:39 : ===FINISHED===
what to do????? i am using xp64....... what do you mean by (Has administrator).
Please help or i to go LG service center???
Thanks in advance
Click to expand...
Click to collapse
By (has administrator) I meant to run kdz with administrator user account rights..
And for your phone not found problem, did you uninstall everything that I listed? If so then you should shake the phone more vigorously from plugging your phone to usb till the phone is found, seriously. If it is still not found, review if you have followed my instructions without leaving a single one out and retry till you suceed... Best of luck... Any more help.. Ask me.
ganesh3s3 said:
By (has administrator) I meant to run kdz with administrator user account rights..
And for your phone not found problem, did you uninstall everything that I listed? If so then you should shake the phone more vigorously from plugging your phone to usb till the phone is found, seriously. If it is still not found, review if you have followed my instructions without leaving a single one out and retry till you suceed... Best of luck... Any more help.. Ask me.
Click to expand...
Click to collapse
when i try to run updater as administrator in winxp 64 it is asking for password ??? i didint set any password...and default user have administrator right without any password....what to do.....bit tense please help me out..... please
maxupload said:
when i try to run updater as administrator in winxp 64 it is asking for password ??? i didint set any password...and default user have administrator right without any password....what to do.....bit tense please help me out..... please
Click to expand...
Click to collapse
Ok if you can't run it as an administrator try skipping that step and try connecting your phone without admin till your is found.. Try SHAKING...
If it doesn't work.. Take your phone and equipment to your friends home which has admin rights...try till you suceed because it usually is a painfree process.. You can fix your phone if it goes to emergency mode... Dont worry.. feel free to ask for help...
Did my P500 Dead?
Hi there,
I had LG P500 with firmware 2.2.1 10e. And The 2.2.1 cannot be root. So i down it to 2.2 and 10b indian. And I use thunderg....recovery from xda. And then i update it vai recovery by applying update.zip and finally i had 2.3.1. It work great but the camera not work, So i decided to down to 2.2 but while i update using kdz updater It just running to param : 36....it stop and show upgrade error. While my phone in emergency mode i removed battery and open it back. It just show Lg logo and at the moment all my home...back...button light was always blink , it just keep at lg logo screen!!! ....
. Too much sorry for my English cuz it not my native i come from Cambodia. And too much much and more thank if you could help me.
SmartLCN said:
Hi there,
I had LG P500 with firmware 2.2.1 10e. And The 2.2.1 cannot be root. So i down it to 2.2 and 10b indian. And I use thunderg....recovery from xda. And then i update it vai recovery by applying update.zip and finally i had 2.3.1. It work great but the camera not work, So i decided to down to 2.2 but while i update using kdz updater It just running to param : 36....it stop and show upgrade error. While my phone in emergency mode i removed battery and open it back. It just show Lg logo and at the moment all my home...back...button light was always blink , it just keep at lg logo screen!!! ....
. Too much sorry for my English cuz it not my native i come from Cambodia. And too much much and more thank if you could help me.
Click to expand...
Click to collapse
Try my above method again and again and if it doesn't work try an another firmware or on an another computer... If nothing works then stick with the 2.3 if you can boot into recovery...
LG P500 does not care
Hello everybody I'm new to the portal, I had tried to update my phone, he was given an error now will not turn anyone knows how to help me I thank you
hug
Doors it show any error when booting or wont even switch on... If it lights up, Try my method...
Sent from my LG-P500 using XDA Premium App
i know it says for lg optimus one but is there a way that it will work for lg optimus v?
still stuck in android logo even after following all the procedures
can anyone help me
eventhough i had successfully change the firmware of phone, it still boot loop in androind logo i dont know what to do
ty
maxupload said:
i tried this but got msg:
[R&D Test Tools Log File]
12:20:25 : Launching SW update
12:20:25 : Unpacking KDZ
12:20:31 : KDZ file extraced
12:20:32 : Files were extracted.
12:20:32 : LGMobileDL Load.
12:20:32 : Port = 3
12:20:32 : Connecting to phone
12:20:37 : PHONE WAS NOT FOUND!
12:20:39 : ===FINISHED===
what to do????? i am using xp64....... what do you mean by (Has administrator).
Please help or i to go LG service center???
Thanks in advance
Click to expand...
Click to collapse
i have got same probem
lg drivers installed, LGE modem disabled
win xp 32bit
It may work on Optimus V... Try it out...
Sent from my LG-P500 using XDA Premium App
alphamale20 said:
can anyone help me
eventhough i had successfully change the firmware of phone, it still boot loop in androind logo i dont know what to do
ty
Click to expand...
Click to collapse
Try my method and say if it works... Reflashing the firmware should do it...
Sent from my LG-P500 using XDA Premium App
guys pls help....emergency mode is not comming when iam pressing that key combination..i think i bricked my phone.....help plss...
i unbricked my phone..still i cant believ i did that.......spend one complete day for it.....in KDZ updater you should select emergency mode instead of DIAG.....dont forget to disable the LG modem in device manager...and also make sure that your downloaded firmware file is working......best of luck guys....
alxbsl96 said:
guys pls help....emergency mode is not comming when iam pressing that key combination..i think i bricked my phone.....help plss...
Click to expand...
Click to collapse
Either you completely bricked your phone or there is no charge left in it... Try charging for sometime and Try...
pkosnovsky said:
i have got same probem
lg drivers installed, LGE modem disabled
win xp 32bit
Click to expand...
Click to collapse
Try shaking more or try it in all three modes where you selected diag ... try every combo till you succeed... Best of luck....
Hey, so, my LG update never finished, and I followed this guide: http://forum.xda-developers.com/showthread.php?t=1180331
But I do not have XP, and the KDZ program doesn't work on Windows7 (I have both 64 and 32 bit)
So I googled around a bit, managed to get a recovery thing loaded on the phone (ClockworkMod Recovery v3.0.2.4)
Then, I tried installing Cyanogen, which I've heard good things about.
I followed this guide perfectly: http://wiki.cyanogenmod.com/wiki/LG_G2x:_Recovery_and_CyanogenMod
The only thing that didn't match the guide was the result of rebooting the device from the recovery menu.
The phone still shows the:
S/W Upgrade
Please wait
while upgrading...
screen. =\
http://forum.xda-developers.com/showthread.php?t=1180331
once you're on that software update screen, you have to try everything known to man to finish the update. no matter what rom or recovery you flash, it won't get past that screen until you get the update flashed correctly.
crazythunder said:
http://forum.xda-developers.com/showthread.php?t=1180331
Click to expand...
Click to collapse
Thanks for linking me to the page I said I already tried, and explained why it wouldn't work.
DerNalia said:
Thanks for linking me to the page I said I already tried, and explained why it wouldn't work.
Click to expand...
Click to collapse
it does work on win7,for some. maybe doing a clean install of your os might help. make a backup to dvd or external hard drive first. that way you can just restore after you update. or get a hold of someone with an xp pc. or call lg.
crazythunder said:
it does work on win7,for some. maybe doing a clean install of your os might help. make a backup to dvd or external hard drive first. that way you can just restore after you update. or get a hold of someone with an xp pc. or call lg.
Click to expand...
Click to collapse
There has to be another way. I hate re-installing OSes. and LG is pretty useless when it comes to fixing things.
I did try installing "XP Mode" but the update failed to install.... and apparently there isn't a version of Virtual PC that can run the XP Mode Hard Disk without having been installed via windows update. =\
DerNalia said:
There has to be another way. I hate re-installing OSes. and LG is pretty useless when it comes to fixing things.
I did try installing "XP Mode" but the update failed to install.... and apparently there isn't a version of Virtual PC that can run the XP Mode Hard Disk without having been installed via windows update. =\
Click to expand...
Click to collapse
if there was "another way" someone would have posted it.
if you absolutely intend on fixing it yourself, you need to try everything possible. if you're looking for an easy way out, not gonna happen. have you tried it on win7? it's worked for some people.
crazythunder said:
. have you tried it on win7? it's worked for some people.
Click to expand...
Click to collapse
Yeah. I've tried my balls off =(
I've discovered that the KDZ program will unfreeze if I unplug the phone from USB while it's updating. (I waited a few hours to make sure this would be safe).
I'm using Windows XP Professional 64bit.
I get this:
[R&D Test Tools Log File]
02:12:23 : Launching SW update
02:12:23 : Unpacking KDZ
02:12:24 : KDZ file extraced
02:12:25 : Files were extracted.
02:12:25 : LGMobileDL Load.
02:12:25 : Port = -1
02:12:25 : Connecting to phone
02:12:25 : PHONE WAS NOT FOUND!
02:12:27 : ===FINISHED===
I have to reboot the phone before the KDZ program will do anything other than the above log.
But then KDZ freezes again. and.. the process repeats. So... It seems that there is some connection issue between KDZ, and the Phone in my version of windows.
EDIT:
something else I noticed:
When I plug me phone into the comupeter: it shows
LGE CDMA Composite USB Device : Ready to use
Unidentified Device : ( ) Installing driver software
Unidentified Device : ( ) Installing driver software
could this be part of the problem?
I tried installing the drivers linked to from the thread that claims to fix this issue, but it said that I had newer ones.
That I had version 3.0.2 and that was never than 3.2 =\
EDIT2:
In device manager, the unknown device is this: USB\VID_1004&PID_6000_DIAGInterface
EDIT3:
Somehow one of the unidentified devices identified itsself.
LGE CDMA USB Serial Port (COM3) : Ready to use
I would try XP 32-bit if you can. Crazythunder is right. At this point, you need to either get the KDZ flasher to work, or send your phone to LG.
DerNalia said:
I've discovered that the KDZ program will unfreeze if I unplug the phone from USB while it's updating. (I waited a few hours to make sure this would be safe).
I'm using Windows XP Professional 64bit.
I get this:
[R&D Test Tools Log File]
02:12:23 : Launching SW update
02:12:23 : Unpacking KDZ
02:12:24 : KDZ file extraced
02:12:25 : Files were extracted.
02:12:25 : LGMobileDL Load.
02:12:25 : Port = -1
02:12:25 : Connecting to phone
02:12:25 : PHONE WAS NOT FOUND!
02:12:27 : ===FINISHED===
I have to reboot the phone before the KDZ program will do anything other than the above log.
But then KDZ freezes again. and.. the process repeats. So... It seems that there is some connection issue between KDZ, and the Phone in my version of windows.
EDIT:
something else I noticed:
When I plug me phone into the comupeter: it shows
LGE CDMA Composite USB Device : Ready to use
Unidentified Device : ( ) Installing driver software
Unidentified Device : ( ) Installing driver software
could this be part of the problem?
I tried installing the drivers linked to from the thread that claims to fix this issue, but it said that I had newer ones.
That I had version 3.0.2 and that was never than 3.2 =\
EDIT2:
In device manager, the unknown device is this: USB\VID_1004&PID_6000_DIAGInterface
EDIT3:
Somehow one of the unidentified devices identified itsself.
LGE CDMA USB Serial Port (COM3) : Ready to use
Click to expand...
Click to collapse
This was my hangup at one point also. In order to have your phone recognized again download the latest LG g2x drivers from LG, uninstall current drivers, reboot PC, install new drivers and then try update tool again.
Sent from my LG-P999 using XDA App
I was flashing the latest recovery mod but it failed and i accidentally rebooted the phone. Now it is bricked. Stuck at fastmode enabled. udc_start().
I am trying the flash the original firmware via tha KDZ but after launching the update KDZ throws me an error...Extract File Error
[R&D Test Tools Log File]
19:24:37 : Launching SW update
19:24:37 : Unpacking KDZ
19:24:40 : KDZ file extraced
19:24:40 : Extract file error
19:24:42 : ===FINISHED===
I tried with two Stock Roms...
Please help me in this....
Basically on a windows machine you download kdz updater and uncompress it as it is a zip file.
Download from here.
This is what I did on an xp laptop.
I had to down load the drivers from the official lg site. when here you enter the code that is on the box the phone came in or under the battery.
Chose the your county and laguage from the drop down box at the top right of the dialogue box. Then from the middle you can choose the drivers. For some reason I had to find the files and click on them to install the driver.
Ok once you decompress kdz updater there are three seperate files to work with. 1. windows enabler. 2. msxml.msi 3.KDZ_FW_UPD.exe
You will also need to download the right file to restore with,You can find it with google.
Please check here the The_ERROR thread wich explains it very well:
[ROMS] Original LG Firmware list.
Install msxml now.
Now you have to boot the phone into rescue mode. On Lg Optimus One turn phone off even if it means taking out the battery.
Press power - volume up - back (this button is next to the home button).
Connect to usb now.Computer found new hardware and installed four drivers.
Then open device manager. Left click my computer - properties - device manager. You need to disable the lg modem driver. Left click on it and disable.
Now launch kdz updater. There will be a drop box on left set to 3gspt or similiar. on the right drop box set to diag. The long box just above the info box with a file at the side lets you browse to find restore file. e.g. V10a.00.kdz.
Double click the button below and let it do it's thing. Took 15min. My phone shut down and came up with an error at the last minute. Anyway I rebooted and all was good.
Everything was the way I left it. Just had to re-root.
My only real problem was getting the kdz installer to see the phone.
After installing the drivers restart pc. If it finishes quickly and just before saying finished it says phone not found try removing all phone related drivers including nokia pc suite and the lg suite and remove and reinstall the drivers.
LITTLE ADVICE :You should use some search and keep your eyes open
Two threads related to this are there on the first page itself.
i need help stuck on emergency mode and computer wont recognize phone it did a at the beginning but when connecting I got partition error table on LGMDP, also got an error on KDZ saying someting with error code 1002 ... please help don't wanna take out the battery cause i'm afraid i would have officially bricked it as in it wouldn't start back up! please willing to try anything at the moment!
Just follow the steps which I mentioned above and everything will be alright.
Sent from my LG-P500 using XDA App
help me..!!
m also struck on emergency mode
i have try to flash using kdz...(v20d.00)
but my phon is not detecting..
i try to install drivers..but when i plug my device it says drivers not found..
please help me...!!
is it any hardware problem of pc /phone...??
rahulgharat95 said:
m also struck on emergency mode
i have try to flash using kdz...(v20d.00)
but my phon is not detecting..
i try to install drivers..but when i plug my device it says drivers not found..
please help me...!!
is it any hardware problem of pc /phone...??
Click to expand...
Click to collapse
No, i suggest you do not use kdz updater, it had high chances of bricking your phone.
Sent from my LG-P500 using xda app-developers app
Junior Einstein said:
No, i suggest you do not use kdz updater, it had high chances of bricking your phone.
Sent from my LG-P500 using xda app-developers app
Click to expand...
Click to collapse
ok...
but do u have any solution for this..??
Junior Einstein said:
No, i suggest you do not use kdz updater, it had high chances of bricking your phone.
Sent from my LG-P500 using xda app-developers app
Click to expand...
Click to collapse
It once bricked my phone too when I removed battery in emergency mode. But after that I used it many times and it worked flawlessly.
You can definitely use kdz, when you know what are you doing.
Sent from my LG-P500
williamcharles said:
I was flashing the latest recovery mod but it failed and i accidentally rebooted the phone. Now it is bricked. Stuck at fastmode enabled. udc_start().
I am trying the flash the original firmware via tha KDZ but after launching the update KDZ throws me an error...Extract File Error
[R&D Test Tools Log File]
19:24:37 : Launching SW update
19:24:37 : Unpacking KDZ
19:24:40 : KDZ file extraced
19:24:40 : Extract file error
19:24:42 : ===FINISHED===
I tried with two Stock Roms...
Please help me in this....
Click to expand...
Click to collapse
this is exactly what happens for me and it seems there is no solution for it!!!!!!
same problem here can someone help me with lg-D605
This is only for people who have corrupted baseband issues (no signal, ? battery icon, and baseband is listed as unknown); if you are stuck at the s/w upgrade screen, you want another thread.
If you are stuck with a corrupted baseband and are unable to flash a .kdz through the updater, keep reading. I have only tried this on xp, and I have tried it with the kdz software updater and uptext_mod2.
1. Set up your drivers, hold volume down, and plug the phone in.
2. Open your device manager, go to modems, and disable the LGE android modem, leave device manager open
3. Start either KDZ_FW_UPD or UpTestEX_mod2_marwin, load the correct .kdz (v21e_00.01.kdz worked for me) and select cs_emergency, it should say Launching SW Update, then Unpacking KDZ
4. As soon as the next group of lines fills in (starting with KDZ file extracted, ending with Call fn_StartUpgrade, enable the LGE android modem in device manager
5. It will give you several lines with wParam and lParam numbers, and disconnect and reconnect once, then when it is finished, it will show the LG logo. Put your battery back in and boot, it should work, if not, try another .kdz (v21y_00.kdz would not work for me).
I used this to fix my g2x with a corrupted baseband, recorrupted it and uncorrupted it again to verify it works. Thanks to kosh2thamax for the cs_emergency idea,
i tried this but it stopped with this msg "MOD UPtestEX MCF has stopped...." anything i need to do to keep it working? thanks.
arcalim said:
i tried this but it stopped with this msg "MOD UPtestEX MCF has stopped...." anything i need to do to keep it working? thanks.
Click to expand...
Click to collapse
got mine fixed with KDZ offline update, on old XP 32bit machine, my newer XP is nogo i think its a driver issue,,, hope this help,,,, just keep at it.
this method is working for me too
http://forum.xda-developers.com/showthread.php?t=1619932
hey, i downloaded v21y_00.kdz because v21e_00 was not working and switched usb also. This time it worked. Just want to thank you very very much. Whew, I was ready to give up and spend the money for a new phone. Keep it up.
Please help... I'm trying to update v20 f800k to v30e pie using uppercut but something went wrong... To cut it all short, My phone is no longer connection to pc in download mode and not visible in device manager
I have tried to uninstall and reinstall all neccessary lg drivers.
All i get is the korean text
"waiting for connection"
Unknown B92 "now on B61 after numerous battery pullout"
Unknown / E / L / RO
yemkoid said:
Please help... I'm trying to update v20 f800k to v30e pie using uppercut but something went wrong... To cut it all short, My phone is no longer connection to pc in download mode and not visible in device manager
I have tried to uninstall and reinstall all neccessary lg drivers.
All i get is the korean text
"waiting for connection"
Unknown B92 or B93 or B94
Unknown / E / L / RO
https://drive.google.com/open?id=1AD4MVQfzADgdoH80xb6-zxNNID0tTU2f
Click to expand...
Click to collapse
put this .dll in the common folder, let's see if it happened by chance. https://mega.nz/#!qV9WzQSQ!Z0Zkpm-m3LJ01tLthzfE9puNmYlbsOoZR5N-f2VS_mw extract and rename LGUP_common.dll
bernavaldiesel1 said:
Does lgup recognize it? What drivers do you have installed? Let's see if I can help.
If you remove the battery and put it back, does the phone turn on?
Click to expand...
Click to collapse
Thanks for the reply. From all my problem descriptions, and with picture of the phone still turning on to download mode...
I installed,
LGUP_Install_Ver_1_14_3
LGMobileDriver_WHQL_Ver_4.4.2
LGBridge_Setup
UPPERCUT_1.0.0.0
...and despite changing to different usb c, the phone is not any visible to pc nor lgup or device manager.
The main problem i'm facing now are the errors on download mode.
Unknown B92
Unknown / E / L / RO
yemkoid said:
The main problem i'm facing now are the errors on download mode.
Unknown B92
Unknown / E / L / RO
Click to expand...
Click to collapse
put this .dll in the common folder, let's see if it happened by chance. https://mega.nz/#!qV9WzQSQ!Z0Zkpm-m3LJ01tLthzfE9puNmYlbsOoZR5N-f2VS_mw extract and rename LGUP_common.dll
if it works, install the latest version of android 8 for your model with lgup not with uppercut, run the lgup exe.
https://forum.xda-developers.com/v20/how-to/guide-lg-v20-to-life-t3827732/amp/
bernavaldiesel1 said:
put this .dll in the common folder, let's see if it happened by chance. https://mega.nz/#!qV9WzQSQ!Z0Zkpm-m3LJ01tLthzfE9puNmYlbsOoZR5N-f2VS_mw extract and rename LGUP_common.dll
if it works, install the latest version of android 8 for your model with lgup not with uppercut, run the lgup exe.
https://forum.xda-developers.com/v20/how-to/guide-lg-v20-to-life-t3827732/amp/
Click to expand...
Click to collapse
I already placed the common dll for f800k prior to flashing oreo which is the same file and oreo kdz i used to update from nougat.
still, pc isn't making any sound of connection of phone been connected
Also the LGflashtool from the second link i already tried earlier. COM41 is not recognised since the phone doesnt communicate with the ports, so not visible to Device manager
yemkoid said:
I already placed the common dll for f800k prior to flashing oreo which is the same file and oreo kdz i used to update from nougat.
still, pc isn't making any sound of connection of phone been connected
Also the LGflashtool from the second link i already tried earlier. COM41 is not recognised since the phone doesnt communicate with the ports, so not visible to Device manager
Click to expand...
Click to collapse
If you remove the battery and put it back, is the phone still the same? The cell phone cannot be turned on, so it is a brick. I will go looking for possible solutions, and consider the possibility of using another PC or try to install updates for your PC if it is not already installed.
When i remove and reinsert and then using the vol- & power button combo the phone is still entering download mode with the Unknown / E / L / RO error
Maybe i'll try another pc and give back reply soonest Thanks
I think I have a similar problem that I solved. I wanted to try to flash the root on 9 android, but it didn’t work, the smartphone stopped showing in download mode and in the device manager, but it was detected in fastboot mode. I'm not sure that I showed the same errors, since the stripes on the screen did not allow me to examine the text. Flash recovery https://androidfilehost.com/?fid=11410932744536982447 through fastboot mode, and in recovery-> format data, flash firmware in zip format from 995 https://forum.xda-developers.com/v20/development/vs995-verizon-lg-v20-stock-oreo-rooted-t3845669. After that, the smartphone was detected in download mode and I reflashed it. (I have f800l)
I guess i'm quiet unlucky now in my own case because i am not rooted and no fastboot stuff.
I'm only able to get to Factory Reset menu using the VOL- and POWER BUTTON and releasing the power button and press again POWER BUTTON once lg logo appears.
Also I'm able to get to a SELECT MENU that contains MA-USB(WIFI) DL, POWER OFF, PHONE INFO, BACK by tapping the VOL- or POWER BUTTON like 6 to 7 times repeatedly while in download mode.
Neither of those helping the situation
yet the value of B kept on decreasing now on B59. May that is for the battery? Unknown BATTERY59