Database Info

qtek s200 unable to start after update failure

Hello,
it was updating the ROM of my s200 and failure to load, since then it only leaves the welcome screen and it does not get to load SO never.
I have read threads of xda-developers, download romupdate, mtty and ntrw, with romupdate i connect with s200, but I cannot restore the ROM.
Also I have tried it the other way around: to overturn a new ROM in card SD and to put it in s200 so that carge of automatic form, but does not make case. Attached log of romupdate, in seems that it connect thes200 and in a while it even says to me that puts the SD card. If attempt the command usb says that this to me in usb already. somebody has been able to happen of this point? Thanks and greetings.
Sorry for my english.
-------------------------
IPL 2.09
SPL 2.20
------------------------
Cmd>info 0
GetDeviceInfo=0x00000000
Prophet
Cmd>info 1
GetDeviceInfo=0x00000001
2.20.0000
Cmd>info 2
GetDeviceInfo=0x00000002
+ SD Controller init
- SD Controller init
+StorageInit
***** user area size = 0x7AC00000 Bytes
HTCSPROQTK35 ¤RHTCE
Cmd>usb
I already connect to USB!
Cmd>l
clean up the image temp buffer at 0x8C100000 Length 0x03900000
BOOTLOAD_PAGE_TABLE_BASE_C_VIRTUAL= 0x8C080000
Clear image temp buffer done .
MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
Cmd>d2s 80000000 02000000
Invalid command : d2s 80000000 02000000
For a help screen, use command ? or h
Cmd>r2sd all
R2SDBackup() Pls. insert SD card !!
Cmd>r2sd all
***** user area size = 0x7AC00000 Bytes
R2SDBackup() - Download type = 5
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
You didn't get the proper security level to download a specific image
Cmd>

[REF]Recover HTC Touch from tricolors RUU boot-loader (Mtty)[ONLINE]

This is the tricolor RUU boot-loader:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
1) Disable USB in your ActiveSync program.
2) Download and run the mtty.exe
3) Change the port to "USB" & Flow control to "RTS/CTS"
4) Press <Enter> once and you should able to see "Cmd>"
5) Issue the following command:
Code:
[B]Cmd>password BsaD5SeoA[/B]
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDInit - SD ver1.0
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDInit: ACMD41 wait for power up bit timeout
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDInit - SD ver2.00
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Card status error in response. MMC_STAT = 4000
SDInit: ACMD41 wait for power up bit timeout
g_cKeyCardSecurityLevel = FF
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
HTCST
[B]Cmd>ruurun 0[/B]
[B]Cmd>ResetDevice[/B]
if no luck, please try information and method from CyZeek bro, http://forum.xda-developers.com/showthread.php?t=379318

any chance of flashing ?
wdata &
erase &
rbmc functions ?

Still stuck at the 'smart mobility' screen if I don't enter bootloader

1) Simultaneous press and hold "Power" and "Camera" key.
2) Press "Reset" once with the stylus and then release all keys.

mkhattab said:
Still stuck at the 'smart mobility' screen if I don't enter bootloader
Click to expand...
Click to collapse
then I think you have to try flash a original ROM suit your device in boot-loader.

also doesn't work...
I think I need to find a way to downgrade SPL or even re-install my existing SPL (2.20)

i just learnt that very important before to flash ROM:
REMOVE SD Card (Maybe only MicroHCSD, but I think better to remove all SD Card)

Hi Andrew,
I just bought my Touch and got stuck at this screen when trying to upload a new ROM to it.
Thanks for this tip, man. I've saved me.
Regards!
Paulo.

TyTN II is frozen at the Smart Mobility screen and restarts constantly
My TyTN II is frozen at the Smart Mobility screen and restarts constantly. I have tried soft restart, hard restart and nothing changes. When it happened I had to soft reset my phone after my "Phone in the phone" stopped working proplerly. I hit the soft reset button and the it just freezes in Smart Mobility and then restarts, vibrates, freezes and etc.. Soft restet does not do anyting, hard reset goes through the process of cleaning and reseting and then nothing, the same problem keeps coming up. Does anyone have any ideas?

did you tried to flash an original ROM from manufacturer in the tricolor boot-loader ? i think this is the only way to make it work again first, although I didn't tried b4.
i think the root cause is, your ROM is incomplete or corrupted, you can't update any 3rd party ROM because only special 'blank' boot-loader will eat 'em. so, what you need to do is to find an original ROM suit your hardware.

What works on the Hermes
Downloading the original rofrom my carrier AT&T & installing has worked atleast 4 to 5 times for me.

Continue...
How to flash back the original HTC ROM ?
Or, when your ROM data have problem, it can boot to tricolors boot-loader only.
1, Make sure your HTC Touch is on the tricolors RUU boot-loader, and being connected to your PC.
2, download and run the ROM image from HTC site, it works for my HTC Touch (Soft Black)
http://www.dopodasia.com/download/RUU_Elfin_DOPODASIA_WWE_2.20.707.1B_4.1.13.51_03.07.90_BLUE_Ship_Reduced.exe
3, Suppose it can regonize your Touch.

4, Continue and let it goes through the process in your Touch and your PC.
5, Congratulations !
6, ROM version 2.20.707.1B is flashed to your HTC Touch.

thanks but i stuck at end tooo
i have same problem and was following ur tips from begining......after that cmd stuff......now i have black screen with writen on it smart mobility.....and i tried every way to come back to boot loader but failed so stuck no where......need ur help....

Big Thanks
I WAS STUCK AND WITHOUT UR ARTICLE AND DETAIL DESCRIPTION I WOULD BE LOST ......i do not know much but always fingring my hard and software and than running for help...... ur whole description is master piece plz add one point there.....if u need to have a bootloader screen another way is ......... 1..switch power off...2.take usb out...3.press camera button... 4.put usb back.....it will be bootloader screen.... chheersss...

tintin007 said:
i have same problem and was following ur tips from begining......after that cmd stuff......now i have black screen with writen on it smart mobility.....and i tried every way to come back to boot loader but failed so stuck no where......need ur help....
Click to expand...
Click to collapse
You can enter bootloader by doing this:
Hold down the camera button and reset device with the stylus. Release the reset and continue holding the camera button until you see a tricolor bootloader screen.

NEED HELP
i was stuck on bootloader after flashing rom and with help in this thread i manage to flash and now problem is i am un able to flash a rom with more free space....... when i try i stuck on screen with a penguin and saying ipl spl loading and nothing happens.........can some one help...plz

keep trying sometimes it takes a few trys b4 you cana cutally get to the blank white screen after completing the CID unlock

andrewloh said:
This is the tricolor RUU boot-loader:
1) Disable USB in your ActiveSync program.
2) Download and run the mtty.exe
3) Change the port to "USB" & Flow control to "RTS/CTS"
4) Press <Enter> once and you should able to see "Cmd>"
5) Issue the following command:
Code:
[B]Cmd>password BsaD5SeoA[/B]
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDInit - SD ver1.0
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDInit: ACMD41 wait for power up bit timeout
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDInit - SD ver2.00
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Card status error in response. MMC_STAT = 4000
SDInit: ACMD41 wait for power up bit timeout
g_cKeyCardSecurityLevel = FF
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
HTCST
[B]Cmd>ruurun 0
Cmd>ResetDevice[/B]
Click to expand...
Click to collapse
I’m truing your method and as I understood I have to copy rom file on SD card and fallow your instructions.
I have 2GB SD card
I copy file to SD card it ELF0ING.nbh
Booted to three color mode and follow your instructions and that what I got and it’s stays at ) present.
password BsaD5SeoA
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDInit - SD ver2.00
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Card status error in response. MMC_STAT = 4000
SD Ver2.00: Low Capacity
SD clock to 24MHz
***** user area size = 0x78000000 Bytes
SDInit---
SDInit OK
g_cKeyCardSecurityLevel = FF
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
HTCST
Cmd>ruurun 0
Cmd>ResetDevice

what rom is the original rom for my touch if my spl and ipl are IPL 2.20.0002
SPL 2.20.0000

fixed the wifi driver is not loaded...

i make this thread because i never found a solution anywhere on the internet about this damn thing.....
so here is the steps i did.
It worked with SPL (USPL) 1.16 by jockyw.
1.boot the vox in bootloader [while the phone is off, hold camera button and plug-in usb]
2.open mtty with usb port. [if u dont see usb port search about it on forum]
3.enter "password BsaD5SeoA" without quotes
4.run the "emapiWlanMac" command [just to test]
5.run the "emapiTest" command [i dont know]
6.run the "emapiWlanEERW" command [i dont know]
7.run the "emapiInit" command [i beleive that this ressurect my wifi]
8.rerun "emapiWlanMac" command" it should be diffrent output.[if it worked]
9.run the "ruurun 0" to load the os after reboot[if u dont do that u will be on the bootloader again after reboot]
10.run the "ResetDevice" to reboot.
And Cheers!!!!
anyway this is the way it worked for me!

Hello akumalol:
-When you enter the commands did you receive a echo or nothing?
-The "password BsaD5SeoA" is standard, do you know if there's another for HTC Tornado?
Best regards,

you should see echo...
i think you have to enter right password to execute commands..

If I enter "info 2" I see echo, but when I enter "password BsaD5SeoA" I don't see echo, and I also I don't receive for the other one commands.
Any idea? maybe wrong password for my Tornado? How can you can the password?

hey dude i am not expert on bootloader, even in htc devices... i cant help u on that.. soz... it is just the way I fixed it on my vox.. maybe you can find it helpfull later... ;D

Hello!
I would like to ask you, I am prompted to enter emapiTest after MTTY
+ emapiTest
1. Power on WLAN
2. Reset WLAN
3. Switch MUX to WLAN
5. Init WLAN SDIO interface
6. DeviceID Test
DeviceID = 7030101
NOT EEPROMless configuration!
DeviceID [H2-H1-L2-L1] = F40D0080-B6FA0684-20000000-98C
-emapiTest
After the order is not the ID into 7,030,101 will WIFI?
By the way, my phone is a juno

I am a Chinese, and English is not good, sorry!
I would like to know where these orders are obtained?

sorry man cant help you... it worked on my vox this way...
and i dont really understand what are u trying to tell...

表于 2009-8-30 11:44 PM 只看该作者
Cmd>password BsaD5SeoA
Pass.
+ SD Controller init
- SD Controller init
SDHost controller change to mode 6
+StorageInit
SDInit+++
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDInit - SD ver1.0
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
g_cKeyCardSecurityLevel = 0
Type (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
HTCST
Cmd>emapiWlanMac
Notice: This MAC address takes effect only when your platform is EEPRON-less configuration. Please use (emapiTest) to verify it !
Copying GSM DATA image to SDRAM:00004000
Wlan data header ++++++++++++++++++++
Signature : 0xEE1251
UpdateStatus : 0x1
UpdateCount : 0x1
BodyLength : 0x2D9
BodyCRC : 0xFAE9B2E8
aDieId(0) : 0x0
aDieId(1) : 0x0
aDieId(2) : 0x0
aDieId(3) : 0x0
countryID : 0x0
dwWifiFlag : 0x1
Wlan data header --------------------------
0x00000008
0x00000000
0x00000028
0x00000032
0x00000000
0x00000000
Cmd>emapiTest
+emapiTest
1. Power on WLAN
2. Reset WLAN
3. Switch MUX to WLAN
5. Init WLAN SDIO interface
6. DeviceID Test
DeviceID = 7030101
NOT EEPROMless configuration!
DeviceID[H2-H1-L2-L1] = F40D0080-B6FA0684-20000000-98C
-emapiTest
Cmd>emapiWlanEERW
Copying GSM DATA image to SDRAM:00004000
Wlan data header ++++++++++++++++++++
Signature : 0xEE1251
UpdateStatus : 0x1
UpdateCount : 0x1
BodyLength : 0x2D9
BodyCRC : 0xFAE9B2E8
aDieId(0) : 0x0
aDieId(1) : 0x0
aDieId(2) : 0x0
aDieId(3) : 0x0
countryID : 0x0
dwWifiFlag : 0x1
Wlan data header --------------------------
Wrong format
Cmd>emapiInit
+emapInit default WALN EEPROM data
0. GSM data checksum value = 0x5475928D
1. GSM data checksum value = 0x5475928D
2. GSM data checksum value = 0x5475928D
Initialize wlan data success
-emapInit
Cmd>emapiWlanMac
Notice: This MAC address takes effect only when your platform is EEPRON-less configuration. Please use (emapiTest) to verify it !
Copying GSM DATA image to SDRAM:00004000
Wlan data header ++++++++++++++++++++
Signature : 0xEE1251
UpdateStatus : 0x1
UpdateCount : 0x1
BodyLength : 0x2D9
BodyCRC : 0xFAE9B2E8
aDieId(0) : 0x0
aDieId(1) : 0x0
aDieId(2) : 0x0
aDieId(3) : 0x0
countryID : 0x0
dwWifiFlag : 0x1
Wlan data header --------------------------
0x00000008
0x00000000
0x00000028
0x00000032
0x00000000
0x00000000
Cmd>ruurun 0
Cmd>ResetDevice

The results obtained above, phone still can not find wlan

Cmd>emapiInit
+emapInit default WALN EEPROM data
0. GSM data checksum value = 0x5475928D
1. GSM data checksum value = 0x5475928D
2. GSM data checksum value = 0x5475928D
Initialize wlan data success
-emapInit
That is weird... it says "Initialize wlan data success"...
I dont know man... try playing with emapitest commands... and find some more bootloader info/commands for ur phone... good luck

akumalol said:
i make this thread because i never found a solution anywhere on the internet about this damn thing.....
so here is the steps i did.
It worked with SPL (USPL) 1.16 by jockyw.
1.boot the vox in bootloader [while the phone is off, hold camera button and plug-in usb]
2.open mtty with usb port. [if u dont see usb port search about it on forum]
3.enter "password BsaD5SeoA" without quotes
4.run the "emapiWlanMac" command [just to test]
5.run the "emapiTest" command [i dont know]
6.run the "emapiWlanEERW" command [i dont know]
7.run the "emapiInit" command [i beleive that this ressurect my wifi]
8.rerun "emapiWlanMac" command" it should be diffrent output.[if it worked]
9.run the "ruurun 0" to load the os after reboot[if u dont do that u will be on the bootloader again after reboot]
10.run the "ResetDevice" to reboot.
And Cheers!!!!
anyway this is the way it worked for me!
Click to expand...
Click to collapse
after enter“emapiTest”,it make a error.what i ca see on the phone was “0%”.it just like rebuilding the system .i can not restar my phone ……finally,i have to rebuild my system .my phone is htc c750(shadow ).and i want to know which system you use.

As u can see this is the vox forum. so i used htc vox aka htc s710

can you tell me how the tool works ? maybe i would understand What should I do.When you fixing your phone ,was there a Rom ?

my herald in only bootloader mode???!

I was trying to upgrade my herald with this file and oldest:
HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe
RUU_Herald_HTC_WWE_1.8.405.1_02.71.90_Ship.exe
but i give a error:
Error 300
Invalid Update Tool
my ipl is 1.08.0001
mtty information:
Code:
Cmd>password BsaD5SeoA
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
PL_SDSetSlotNumber() - MPUIO_SDIF_SEL1=0, MPUIO_SD_IF_SEL=0
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDInit - SD ver1.0
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
PL_SDSetSlotNumber() - MPUIO_SDIF_SEL1=0, MPUIO_SD_IF_SEL=0
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDInit - SD ver1.0
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
GetDeviceCID: Error - InitDecoder
g_cKeyCardSecurityLevel = FF
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
RUURUN fail
HTCSF
Cmd>
now my herald only goto bootmode
what can i do?
please help
thanks very much

This happened to me once before.
I got my hands on the latest official tmobile wing rom, (you can snag it off the tmobile.com , or someone has it on here.)
connect ppc to pc via active sync
wait for all that crap to connect
open the ruu
and it should flash back to stock.
If not, then hard reset ppc, see if that does anything.
then do the previous.
hope this helps.

Don't post 4 new threads, all about you. You posted 3 threads in the ROM Development section, and I don't think you're "Developing" a ROM. And you posted the same thread in both the ROM Development AND the Herald forums.
I know you're stuck, but just post one thread, in the right location, and then someone will help you. Posting 4 threads doesn't make a difference.

Don't post 4 new threads, all about you. You posted 3 threads in the ROM Development section, and I don't think you're "Developing" a ROM. And you posted the same thread in both the ROM Development AND the Herald forums.
I know you're stuck, but just post one thread, in the right location, and then someone will help you. Posting 4 threads doesn't make a difference.
Click to expand...
Click to collapse
yes you right but:
ok whats exactly i mus to do for my device?
thanks sir

Obviously he doesn't know or he would have given you the solution. Unfortunately I don't have the solution either. You're probably going to have to Goldcard it. Search for it.
He is right though, cross-posting is a big no-no.

[Q]

i buy this chines gps from ebay..its running win ce 6.0 ... i use a modified script to acces all my navcore that i instaled. the problem is i don`t know the command for exit...this script was for mio but it works on my gps but the exit button doesent work...the script look like this:
ICONXPBUTTON
x = -8
y = -16
Command = "\Storage Card\MioAutoRun\Programs\Utils\mspower.exe"
SizeNormal = 80
SizePushed = 70
ScaleAlpha = 100
IconNormal = ..\Icons\ff.ico
ScaleAlpha = 100
IconPushed = ..\Icons\ff_.ico
i change the path...still not working....i need the command to exit from a window
i want to be able to exit my script once i hit the exit button