Hello,
it was updating the ROM of my s200 and failure to load, since then it only leaves the welcome screen and it does not get to load SO never.
I have read threads of xda-developers, download romupdate, mtty and ntrw, with romupdate i connect with s200, but I cannot restore the ROM.
Also I have tried it the other way around: to overturn a new ROM in card SD and to put it in s200 so that carge of automatic form, but does not make case. Attached log of romupdate, in seems that it connect thes200 and in a while it even says to me that puts the SD card. If attempt the command usb says that this to me in usb already. somebody has been able to happen of this point? Thanks and greetings.
Sorry for my english.
-------------------------
IPL 2.09
SPL 2.20
------------------------
Cmd>info 0
GetDeviceInfo=0x00000000
Prophet
Cmd>info 1
GetDeviceInfo=0x00000001
2.20.0000
Cmd>info 2
GetDeviceInfo=0x00000002
+ SD Controller init
- SD Controller init
+StorageInit
***** user area size = 0x7AC00000 Bytes
HTCSPROQTK35 ¤RHTCE
Cmd>usb
I already connect to USB!
Cmd>l
clean up the image temp buffer at 0x8C100000 Length 0x03900000
BOOTLOAD_PAGE_TABLE_BASE_C_VIRTUAL= 0x8C080000
Clear image temp buffer done .
MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
Cmd>d2s 80000000 02000000
Invalid command : d2s 80000000 02000000
For a help screen, use command ? or h
Cmd>r2sd all
R2SDBackup() Pls. insert SD card !!
Cmd>r2sd all
***** user area size = 0x7AC00000 Bytes
R2SDBackup() - Download type = 5
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
You didn't get the proper security level to download a specific image
Cmd>
This is the tricolor RUU boot-loader:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
1) Disable USB in your ActiveSync program.
2) Download and run the mtty.exe
3) Change the port to "USB" & Flow control to "RTS/CTS"
4) Press <Enter> once and you should able to see "Cmd>"
5) Issue the following command:
Code:
[B]Cmd>password BsaD5SeoA[/B]
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDInit - SD ver1.0
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDInit: ACMD41 wait for power up bit timeout
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDInit - SD ver2.00
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Card status error in response. MMC_STAT = 4000
SDInit: ACMD41 wait for power up bit timeout
g_cKeyCardSecurityLevel = FF
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
HTCST
[B]Cmd>ruurun 0[/B]
[B]Cmd>ResetDevice[/B]
if no luck, please try information and method from CyZeek bro, http://forum.xda-developers.com/showthread.php?t=379318
any chance of flashing ?
wdata &
erase &
rbmc functions ?
Still stuck at the 'smart mobility' screen if I don't enter bootloader
1) Simultaneous press and hold "Power" and "Camera" key.
2) Press "Reset" once with the stylus and then release all keys.
mkhattab said:
Still stuck at the 'smart mobility' screen if I don't enter bootloader
Click to expand...
Click to collapse
then I think you have to try flash a original ROM suit your device in boot-loader.
also doesn't work...
I think I need to find a way to downgrade SPL or even re-install my existing SPL (2.20)
i just learnt that very important before to flash ROM:
REMOVE SD Card (Maybe only MicroHCSD, but I think better to remove all SD Card)
Hi Andrew,
I just bought my Touch and got stuck at this screen when trying to upload a new ROM to it.
Thanks for this tip, man. I've saved me.
Regards!
Paulo.
TyTN II is frozen at the Smart Mobility screen and restarts constantly
My TyTN II is frozen at the Smart Mobility screen and restarts constantly. I have tried soft restart, hard restart and nothing changes. When it happened I had to soft reset my phone after my "Phone in the phone" stopped working proplerly. I hit the soft reset button and the it just freezes in Smart Mobility and then restarts, vibrates, freezes and etc.. Soft restet does not do anyting, hard reset goes through the process of cleaning and reseting and then nothing, the same problem keeps coming up. Does anyone have any ideas?
did you tried to flash an original ROM from manufacturer in the tricolor boot-loader ? i think this is the only way to make it work again first, although I didn't tried b4.
i think the root cause is, your ROM is incomplete or corrupted, you can't update any 3rd party ROM because only special 'blank' boot-loader will eat 'em. so, what you need to do is to find an original ROM suit your hardware.
What works on the Hermes
Downloading the original rofrom my carrier AT&T & installing has worked atleast 4 to 5 times for me.
Continue...
How to flash back the original HTC ROM ?
Or, when your ROM data have problem, it can boot to tricolors boot-loader only.
1, Make sure your HTC Touch is on the tricolors RUU boot-loader, and being connected to your PC.
2, download and run the ROM image from HTC site, it works for my HTC Touch (Soft Black)
http://www.dopodasia.com/download/RUU_Elfin_DOPODASIA_WWE_2.20.707.1B_4.1.13.51_03.07.90_BLUE_Ship_Reduced.exe
3, Suppose it can regonize your Touch.
4, Continue and let it goes through the process in your Touch and your PC.
5, Congratulations !
6, ROM version 2.20.707.1B is flashed to your HTC Touch.
thanks but i stuck at end tooo
i have same problem and was following ur tips from begining......after that cmd stuff......now i have black screen with writen on it smart mobility.....and i tried every way to come back to boot loader but failed so stuck no where......need ur help....
Big Thanks
I WAS STUCK AND WITHOUT UR ARTICLE AND DETAIL DESCRIPTION I WOULD BE LOST ......i do not know much but always fingring my hard and software and than running for help...... ur whole description is master piece plz add one point there.....if u need to have a bootloader screen another way is ......... 1..switch power off...2.take usb out...3.press camera button... 4.put usb back.....it will be bootloader screen.... chheersss...
tintin007 said:
i have same problem and was following ur tips from begining......after that cmd stuff......now i have black screen with writen on it smart mobility.....and i tried every way to come back to boot loader but failed so stuck no where......need ur help....
Click to expand...
Click to collapse
You can enter bootloader by doing this:
Hold down the camera button and reset device with the stylus. Release the reset and continue holding the camera button until you see a tricolor bootloader screen.
NEED HELP
i was stuck on bootloader after flashing rom and with help in this thread i manage to flash and now problem is i am un able to flash a rom with more free space....... when i try i stuck on screen with a penguin and saying ipl spl loading and nothing happens.........can some one help...plz
keep trying sometimes it takes a few trys b4 you cana cutally get to the blank white screen after completing the CID unlock
andrewloh said:
This is the tricolor RUU boot-loader:
1) Disable USB in your ActiveSync program.
2) Download and run the mtty.exe
3) Change the port to "USB" & Flow control to "RTS/CTS"
4) Press <Enter> once and you should able to see "Cmd>"
5) Issue the following command:
Code:
[B]Cmd>password BsaD5SeoA[/B]
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDInit - SD ver1.0
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDInit: ACMD41 wait for power up bit timeout
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDInit - SD ver2.00
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Card status error in response. MMC_STAT = 4000
SDInit: ACMD41 wait for power up bit timeout
g_cKeyCardSecurityLevel = FF
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
HTCST
[B]Cmd>ruurun 0
Cmd>ResetDevice[/B]
Click to expand...
Click to collapse
I’m truing your method and as I understood I have to copy rom file on SD card and fallow your instructions.
I have 2GB SD card
I copy file to SD card it ELF0ING.nbh
Booted to three color mode and follow your instructions and that what I got and it’s stays at ) present.
password BsaD5SeoA
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDInit - SD ver2.00
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Card status error in response. MMC_STAT = 4000
SD Ver2.00: Low Capacity
SD clock to 24MHz
***** user area size = 0x78000000 Bytes
SDInit---
SDInit OK
g_cKeyCardSecurityLevel = FF
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
HTCST
Cmd>ruurun 0
Cmd>ResetDevice
what rom is the original rom for my touch if my spl and ipl are IPL 2.20.0002
SPL 2.20.0000
Hello I have a Fuze with the stock ROM and am trying to get USB DUN working on GNU/Linux with wvdial. I have tried the following wvdial.conf and some variations of it all with the same problem. I keep getting error code 16 "The modem has hung up" when dialing. If anyone could post a working wvdial.conf for their ATT phone that would be great. I can post the exact error log or anything else if needed. Thanks.
Edit:
Same problem as in this thread:
http://forum.xda-developers.com/showthread.php?p=2609673
[Dialer Defaults]
Modem = /dev/ttyUSB0
ISDN = off
Modem Type = Analog Modem
Baud = 460800
Init = ATZ
Init2 = ATZ+CGDCONT=1,"IP","ISP.CINGULAR"
Init3 =
Init4 =
Init5 =
Init6 =
Init7 =
Init8 =
Init9 =
Phone = *99#
Phone1 =
Phone2 =
Phone3 =
Phone4 =
Dial Prefix =
Dial Attempts = 1
Dial Command = ATDT
#Ask Password = on
Password = CINGULAR1
Username = [email protected]
Auto Reconnect = off
Abort on Busy = off
Carrier Check = on
Check Def Route = on
Abort on No Dialtone = on
Stupid Mode = on
Idle Seconds = 0
Auto DNS = on
Now this is what I call a bump.
Hello
I have a problem with my HTC Herald. When I want to upload the ROM by RUU get the error [244]. In MTTY when I type the command [set 32] I get:
set 32
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
PL_SDSetSlotNumber() - MPUIO_SDIF_SEL1=0, MPUIO_SD_IF_SEL=0
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDInit - SD ver1.0
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SD clock to 24MHz
***** user area size = 0xF400000 Bytes
SDInit---
SDInit OK
GetDeviceCID: Error - InitDecoder
g_cKeyCardSecurityLevel = 0
HTCE
Cmd>
Try to install the ROM from the memory card also failed. I used a 256MB MicroSD card formatted in FAT32. I have installed HardSPL.
Data from the tri-color bootloader:
IPL 4.17.0001
SPL 4.70.Yang
Let me add that before the hard-reset the phone to work properly.
Sorry ... I use Google Translator
Hello all ,
I linked a serial cable to my allwinner a20 based Android Tv box.
It can not pass after the boot logo and next is all what it display in serial console.
Somebody pelase help i need to reisntall linux on it ,if you knwo any u boot keys that i have to press on the uboot serial consoel pelase help.I tryed to press ransom keys but i see nothin.
Here is all i see when it start:
====================================
HELLO! BOOT0 is starting!
boot0 version : 3.0.0
dram size =512
sum=0x9c3bd8cf
src_sum=0x9c3bd8cf
Ready to disable icache.
Jump to secend Boot.
[ 0.133]
U-Boot 2011.09-rc1-dirty (Nov 08 2013 - 11:06:32) Allwinner Technology
[ 0.141]version: 1.1.0
[ 0.144]pmbus: ready
axp read error
probe axp20x failed
axp_probe error
boot_clock = 912
dcdc2_vol = 1400
axp set dcdc2_vol to 1400 failed
dcdc3_vol = 1250
ldo2_vol = 3000
ldo3_vol = 2800
ldo4_vol = 2800
power_start = 0
storage_type = -1
usb_recovery = 0
find power_sply to end
fel key old mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
[ 0.293]DRAM: 512 MiB
relocation Offset is: 15b27000
user_gpio config
user_gpio ok
DRV_DISP_Init: opened
[ 0.560]boot_disp.output_type=2
[ 0.563]boot_disp.output_mode=5
[ 0.567]boot_disp.auto_hpd=1
workmode = 0
[ 1.871]NAND: NAND_UbootInit
NB1 : enter NAND_LogicInit
nand : get id_number_ctl from script, 3
not burn nand partition table!
NB1 : nftl num: 3
init nftl: 0
NB1 : NAND_LogicInit ok, result = 0x0
[ 2.381]sunxi flash init ok
In: serial
Out: serial
Err: serial
--------fastboot partitions--------
-total partitions:12-
-name- -start- -size-
bootloader : 1000000 1000000
env : 2000000 1000000
boot : 3000000 1000000
system : 4000000 20000000
recovery : 24000000 2000000
databk : 26000000 2000000
misc : 28000000 1000000
private : 29000000 1000000
sysrecovery : 2a000000 21000000
data : 4b000000 40000000
cache : 8b000000 17000000
UDISK : a2000000 0
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_nand
key 0
recovery key high 6, low 4
cant find fstbt value
Fastboot detected, will boot fastboot
to be run cmd=run setargs_nand boot_fastboot
the user data'magic is bad
WORK_MODE_BOOT
board_status_probe
sunxi_bmp_display
WORK_MODE_BOOT
[ 2.509]Hit any key to stop autoboot: 0
run usb fastboot
sunxi_fastboot_init
recv addr 0x41000000
send addr 0x582580a8
delay time 0
usb init ok
------------------------------------------------------------------
After this nothing .Please help me
After searching all google and reading documantation ,I contacted the box seller and he gied me the files i neeeded.
I used a image file named sun7i_A20v2.0_android_sugar-ref001_2014.09.04_TakenYBSJ.img and a windwos software to flash it via usb named PhoenixPacketV333
To flash teh device you muist hava a serial console to the box (veru easy to do if you have the cable ) ,and keep pushed the key 2
on serial consle (putty) while powering the device ,so it enter in fel mode ( something like recovery mode ,it accept usb connection) .Then oyu need a usb male to male cable to conect the android tv box usb port to the windows usb port ,and start flasing using the PhoenixPacketV333 software.
If somebody needs more help or files just write here I check daily .
have a nice day all!