Hi...without opening the back cover and without removing the battery , is it possible to enter download mod and using ODIN to flash the skyrocket ? I don't want to open the back cover...
Thanks
mahanddeem said:
Hi...without opening the back cover and without removing the battery , is it possible to enter download mod and using ODIN to flash the skyrocket ? I don't want to open the back cover...
Thanks
Click to expand...
Click to collapse
Yeah you can enter download mode just be turning your phone off normally and holding volume up and down while plugging it into the computer. Also, holding the power button for around 10 seconds or so simulates a battery pull anyways.
Yes, you can.
Just shut down your phone.
Make sure it's power off, hold both VOL UP & VOL DOWN, then plug in the USB
Can I also restart the phone in download mod using adb command from cmd ?
mahanddeem said:
Can I also restart the phone in download mod using adb command from cmd ?
Click to expand...
Click to collapse
Yeah
ADB reboot download
Is the command you're looking for. Enter in windows command prompt with your phone plugged in, assuming you've already set up your computer with ADB and such.
Sent from my SGH-T989 using xda premium
yoft1 said:
Yeah
ADB reboot download
Is the command you're looking for. Enter in windows command prompt with your phone plugged in, assuming you've already set up your computer with ADB and such.
Sent from my SGH-T989 using xda premium
Click to expand...
Click to collapse
YES you're so great .. thanks .
so :
1.Make sure ADB and stuffs(plus phone USB driver) are installed and running correctly
2.Enable USB debug from phone
3.Connect USB to PC and phone
4.run command from Windows start menu
5.cmd
6.adb reboot download
I hate pressing those candy buttons that's why I like adb...
Another question : should I run ODIN , connect USB cable to PC only , put phone in download mod THEN connect it to the other end of USB ? is that the right sequence ?
mahanddeem said:
YES you're so great .. thanks .
so :
1.Make sure ADB and stuffs(plus phone USB driver) are installed and running correctly
2.Enable USB debug from phone
3.Connect USB to PC and phone
4.run command from Windows start menu
5.cmd
6.adb reboot download
I hate pressing those candy buttons that's why I like adb...
Another question : should I run ODIN , connect USB cable to PC only , put phone in download mod THEN connect it to the other end of USB ? is that the right sequence ?
Click to expand...
Click to collapse
Yeah you can enter download mode just be turning your phone off normally and holding volume up and down while plugging it into the computer.
Click to expand...
Click to collapse
means 'put phone in download mode BY connecting other end of USB.'
That is the only change from how you asked it.
mahanddeem said:
YES you're so great .. thanks .
so :
1.Make sure ADB and stuffs(plus phone USB driver) are installed and running correctly
2.Enable USB debug from phone
3.Connect USB to PC and phone
4.run command from Windows start menu
5.cmd
6.adb reboot download
I hate pressing those candy buttons that's why I like adb...
Another question : should I run ODIN , connect USB cable to PC only , put phone in download mod THEN connect it to the other end of USB ? is that the right sequence ?
Click to expand...
Click to collapse
As the user above me said, download mode only works if your phone is connected to your computer in the first place. So go ahead and plug your phone into your computer and then enter download mode. Also, adb isn't going to be giving your phone any commands if it isn't plugged in
yoft1 said:
As the user above me said, download mode only works if your phone is connected to your computer in the first place. So go ahead and plug your phone into your computer and then enter download mode. Also, adb isn't going to be giving your phone any commands if it isn't plugged in
Click to expand...
Click to collapse
Sure thing...So Odin will it work if the phone is already connected via usb and in download mod by adb command ?
mahanddeem said:
Sure thing...So Odin will it work if the phone is already connected via usb and in download mod by adb command ?
Click to expand...
Click to collapse
Yup, that's how it's supposed to work
Related
Just got my G2x, and I'm excited to install one of the ROMs. I'm trying to install the ClockworkMod Recovery Flasher following the instructions in this tread http://forum.xda-developers.com/showthread.php?t=1056847 but "APX Device" isn't being detected. I have the LG driver installed on the computer. Can someone please help me out?
anjuice said:
Just got my G2x, and I'm excited to install one of the ROMs. I'm trying to install the ClockworkMod Recovery Flasher following the instructions in this tread http://forum.xda-developers.com/showthread.php?t=1056847 but "APX Device" isn't being detected. I have the LG driver installed on the computer. Can someone please help me out?
Click to expand...
Click to collapse
When trying to install the APX driver are you being sure to remove the phone battery, hold volume up+down together, and then plug the phone into the computer? You have to keep both volume buttons held down until the device is recognized. Then you go into device manager on your computer and right click on the APX device and update the driver software from there. Point the driver installation to the APX folder that was unzipped with the nvflash tool. The computer will find the appropriate driver and install it.
phburks said:
When trying to install the APX driver are you being sure to remove the phone battery, hold volume up+down together, and then plug the phone into the computer? You have to keep both volume buttons held down until the device is recognized. Then you go into device manager on your computer and right click on the APX device and update the driver software from there. Point the driver installation to the APX folder that was unzipped with the nvflash tool. The computer will find the appropriate driver and install it.
Click to expand...
Click to collapse
Ahhh, yeah.. Sadly the computer won't recognize it when I hold the volume up+down together and plug it into the computer. Battery is taken out before I attempt it. It's really weird . I was following the directions from the thread down to the T. Thanks a lot for the help!!
Does your computer recognize the phone when you plug it in with the power on? As in can you use usb storage or tethering? If so it should recognize it in apx.
Sent from my Nexus Prime using XDA Ultimate App
anjuice said:
Ahhh, yeah.. Sadly the computer won't recognize it when I hold the volume up+down together and plug it into the computer. Battery is taken out before I attempt it. It's really weird . I was following the directions from the thread down to the T. Thanks a lot for the help!!
Click to expand...
Click to collapse
I wonder if you try uninstalling all drivers for the phone (LG drivers and apx drivers) and install them fresh?
phburks said:
I wonder if you try uninstalling all drivers for the phone (LG drivers and apx drivers) and install them fresh?
Click to expand...
Click to collapse
It seems I haven't installed the APX driver. I do have the One-Click-G2x-recovery-flasher-06-16.rar, and inside is an APX folder with a bunch of .dll files. Are those what I'm supposed to use?
Alright it seems I was able to install the APX driver, thanks for all the help! It was odd... to put it in APX mode I left the battery in and held the power button plus the volume up and down buttons.. Weird.
anjuice said:
Alright it seems I was able to install the APX driver, thanks for all the help! It was odd... to put it in APX mode I left the battery in and held the power button plus the volume up and down buttons.. Weird.
Click to expand...
Click to collapse
Were you using a USB port on your computer or through a hub? You cannot use a hub to flash most phones. Because it worked with your battery it appears that the USB port you used is not supplying the required 5 volts, 500ma it is supposed to supply. Sounds like you were on an unpowered hub and it did not pass through power from the computer as it should.
jboxer said:
Were you using a USB port on your computer or through a hub? You cannot use a hub to flash most phones. Because it worked with your battery it appears that the USB port you used is not supplying the required 5 volts, 500ma it is supposed to supply. Sounds like you were on an unpowered hub and it did not pass through power from the computer as it should.
Click to expand...
Click to collapse
That's possible. I used the USB port that's installed in the front of my tower. Thanks for the explanation!
Virtualbox VM not recognizing phone
I'm using the VirtualBox VM method to flash clockworkmod recovery from this post: [RECOVERY] G2x ClockworkMod flash for Mac. I have completed steps 1-7 and everything seems to be in working order. However, once I pull the battery and hold down the volume up and volume down then plug in the USB. Nothing happens. The phone never turns on nor is recognized by Virtualbox VM. What am I doing wrong?
mylomine said:
I'm using the VirtualBox VM method to flash clockworkmod recovery from this post: [RECOVERY] G2x ClockworkMod flash for Mac. I have completed steps 1-7 and everything seems to be in working order. However, once I pull the battery and hold down the volume up and volume down then plug in the USB. Nothing happens. The phone never turns on nor is recognized by Virtualbox VM. What am I doing wrong?
Click to expand...
Click to collapse
The phone doesn't turn on. You will hear a beep that the phone tried to connect to the computer. Usually driver installation fails. You then go to the control panel, find the device under USB Devices and then direct Windows to manually install the driver from the APX directory. The screen on the phone doesn't show anything until AFTER a successful flash of the recovery (counter-intuitive but that is how it works). If you are using a VB VM setup, you need to make sure the USB ports are assigned to your virtual machine first.
Have one Nexus 5 with "no command " showing on screen so i tried to flash it with Nexus root toolkit, phone froze and after that its dead and when i try to plug it on comp i just get USB composite device with yellow triangle in device manager. Phone is currently dead , not able to enter download mode, no bootloader mode, not showing anything on charger and not turning on.
Any ideas or suggestions please.
Try to update drivers from device manager if its showing a triangle when u connect ur phone! and install [pda net drivers ..
try this method it worked for me! while connecting to charger not on pc or lappy wall charger press Vol+ and Vol- and power button at the same time and connect it to the charger!!
pranavmali said:
Try to update drivers from device manager if its showing a triangle when u connect ur phone! and install [pda net drivers ..
try this method it worked for me! while connecting to charger not on pc or lappy wall charger press Vol+ and Vol- and power button at the same time and connect it to the charger!!
Click to expand...
Click to collapse
Thanks for the reply but the phone does not turn on no matter how i try to connect it and pda net driver need the phone to has enabled USB debugging which i can not do on a dead phone
Try removing battery from the back just the connector and plug it to ur PC don't attach the battery!
Hi guys. I come here in search for help as I already tried possibly all the methods and unbrick solutions that I saw to fix my Oneplus One. Basically when I turn it on it gets stuck on "1+ powered by android" screen. I can't go to Recovery Mode and I can only enter the Fastboot mode if I'm not connected to PC. It doesn't get recognized when I connect it to PC unless I press the "Vol. up + Power" button combination. After this, it gets recognized on windows' device manager as "Qualcomm HS-USB QDLoader 9008" and the phone gets in a mode that doesn't show anything on the screen and apparently necessary to do what's described in this post. This was the last thing that I've tried after I tried several other solutions.
Thanks in advance to anyone who might help me. I love this phone and I hate just the thought of buying a new one.
Twody said:
Hi guys. I come here in search for help as I already tried possibly all the methods and unbrick solutions that I saw to fix my Oneplus One. Basically when I turn it on it gets stuck on "1+ powered by android" screen. I can't go to Recovery Mode and I can only enter the Fastboot mode if I'm not connected to PC. It doesn't get recognized when I connect it to PC unless I press the "Vol. up + Power" button combination. After this, it gets recognized on windows' device manager as "Qualcomm HS-USB QDLoader 9008" and the phone gets in a mode that doesn't show anything on the screen and apparently necessary to do what's described in this post. This was the last thing that I've tried after I tried several other solutions.
Thanks in advance to anyone who might help me. I love this phone and I hate just the thought of buying a new one.
Click to expand...
Click to collapse
Why not just enter into fastboot,install fastboot drivers in pc and connect device in fastboot mode to pc and flash cos13?
Mr.Ak said:
Why not just enter into fastboot,install fastboot drivers in pc and connect device in fastboot mode to pc and flash cos13?
Click to expand...
Click to collapse
I already intalled fastboot drivers and put the phone in fastboot mode. When I plug the phone to the PC it doesn't get recognized. Can you tell me how to install the fastboot drivers? Maybe I missed something.
Twody said:
I already intalled fastboot drivers and put the phone in fastboot mode. When I plug the phone to the PC it doesn't get recognized. Can you tell me how to install the fastboot drivers? Maybe I missed something.
Click to expand...
Click to collapse
https://forum.xda-developers.com/showthread.php?t=2588979
Which windows you're using?
Mr.Ak said:
https://forum.xda-developers.com/showthread.php?t=2588979
Which windows you're using?
Click to expand...
Click to collapse
Yes, that was the one I installed. I'm using windows 10 x64.
Twody said:
Yes, that was the one I installed. I'm using windows 10 x64.
Click to expand...
Click to collapse
Try using win7.
PS: did you launched the tool with administrator privileges?
I download the latest adb and fastboot drivers from Android Studio site under command line tools.
Here is a good Article on how to configure the drivers on your machine.https://www.xda-developers.com/adb-fastboot-any-directory-windows-linux/
I accidentality flashed a wrong oreo Chinese firmware on my international mate (nxt-L29), with that I'm stuck with booth bootloader and FRP lock ("enable OEM unlock" option in developer mode sitting is greyed).
in attempt to resolve this problem I'm asked to put USB ports setting on Manufacture mode in ProjectMenu witch i can't access via *#*#2846579#*#* code on phone.
it shows nothing.
help please....
is there any other method to enable Manufacture mode in usb setting like adb command ?????
note:
when i was in the upgrade mode (phone off, press the tow volume button up and down then connect the micro usb cable) i noticed the device respond to ADB commands and it's detected but unauthorized.
is there a way to make adb works.
tarekcod said:
note:
when i was in the upgrade mode (phone off, press the tow volume button up and down then connect the micro usb cable) i noticed the device respond to ADB commands and it's detected but unauthorized.
is there a way to make adb works.
Click to expand...
Click to collapse
you need to activate usb debugging first in the setting then it will give authorized
ceriqdesign said:
you need to activate usb debugging first in the setting then it will give authorized
Click to expand...
Click to collapse
I'm talking about the upgrade mode here.
tarekcod said:
I'm talking about the upgrade mode here.
Click to expand...
Click to collapse
Haha..#2nd post you said about adb unauthorized..so i respond to the question..
Hi,
My oneplus 8 is notshowing the Qualcomm HS-USB QDLoader 9008 in device manager,therefore i can't usethe unbrick tool,any help or advice please
Install the latest Qualcomm drivers
GraveDigger176 said:
Install the latest Qualcomm drivers
Click to expand...
Click to collapse
Where from please
stavros67 said:
Where from please
Click to expand...
Click to collapse
From this thread............https://forum.xda-developers.com/oneplus-8/how-to/op8-unbrick-tool-to-restore-device-to-t4085877
GraveDigger176 said:
From this thread............https://forum.xda-developers.com/oneplus-8/how-to/op8-unbrick-tool-to-restore-device-to-t4085877
Click to expand...
Click to collapse
Hi,
I press volume up & volume down together,insert cable to pc,the phone is not showing up on device manager,and sometimes the phone goes into fastboot mode?
USB debugging enabled on your phone ?
GraveDigger176 said:
USB debugging enabled on your phone ?
Click to expand...
Click to collapse
Yes,it will not show up Qualcomm HS-USB QDLoader 9008 in device manager,seems to make no difference what drivers i download,seem convinced there is something not right with the phone.
That's right what it shows QDLOADER 9800 what phone you tmo or international\india version
Use different pc or laptop
GraveDigger176 said:
That's right what it shows QDLOADER 9800 what phone you tmo or international\india version
Use different pc or laptop
Click to expand...
Click to collapse
I have the oneplus 8,i have tried a different pc,with the same results.Both pc's recognise the phone,and i can transfer files accross,it will just not show QDLOADER 9800 in device manager.
The phone must be completely shutdown before the cable is inserted.
1: power phone down
2: start your msm app and have it ready
3: hold both volume up and down at the same time and do not release
4: plug USB cable (that is already attached to the PC) into the phone
Your phone will not show any indication that it has powered but you should see it in the MSM tool as well as the device manager.
Juxto2010 said:
The phone must be completely shutdown before the cable is inserted.
1: power phone down
2: start your msm app and have it ready
3: hold both volume up and down at the same time and do not release
4: plug USB cable (that is already attached to the PC) into the phone
Your phone will not show any indication that it has powered but you should see it in the MSM tool as well as the device manager.
Click to expand...
Click to collapse
Have tried this countless times on two different pc's,it does not show up on msm or device manager.Also the when pressing and holding said buttons the phone will sometimes go into fastboot mode.
Try the following, power up your phone let it boot, if is finish with booting plug in your phone with the USB cable and look whether USB debugging is showing in status bar at the left bottom of the screen. If it shows USB debugging open CMD command window and type "adb reboot edl" and see what happens. Before you should start your msn tool that you can tap the enrum button maybe this works
Sorry,bottom of which screen
The phone shows in device manager when powered on and connect to the usb cable as " universal Serial Bus devices - IN2013,then when i try and go into edl mode the device manager does not see it's connected.