Hello all
I downgraded my Qtek 2020 from WM2005 to WM2003 SE.
But now I can't make TomTom 5 recognize my Bluetooth GPS.
In WM 2005 it workes great, but I have the backlight problem, so I come back to 2003 SE thinking that that problem was over, but I was mistaken.
I paired my GPS ok and made the outbond to COM5, but still TomTom don't see my GPS.
I also searched this forum and try'd some of the solutions, but no hope.
Can some one help me with this.
Guys and gals,
I'm using my infrared Stowaway keyboard frequently, because you can type fast . I have been using it with all versions of wm 6 that I have installed until now. Now with wm 6.1 I have big problems, because this keyboard causes my prophet to hang. I like to know if other people have the same problem or found a solution. What is so different between 6.0 and 6.1 that causes my keyboard stops working?
Any answer will be appreciated and any solution even more!
Does anyone know if it is possible to change the bt stack used in 6.1 back to the 6.0 one without downgrading to wm 6.0.
I have some strange problems with 6.1 and my bt car kit. With normal 6.1 stack my kaiser crashed after calling over bt. With 6.1 and jetware kaiser doesn't crash but I can't make outgoing calls over bt device.
With 6.0 I had none of these probs.
Hi,
I do have the same experience with my Vario 3 running WM 6.1 and the VW Premium Carkit which uses the rSap protocol...
Any solutions in the meantime with WM 6.1??
regards from berlin
I installed Profiles for Windows mobile on WM 6.0 and it worked well, then I upgraded my Cruise to WM 6.1, I reinstalled Profiles, but now I have a problem: when I change the profile from a single bip to normal mode, the sms tone doesn't change. Any suggestion?
I had a great little app on my Touch Diamond that enabled Bluetooth whenever it was on external power (great for linking to the car bluetooth headset). However, it doesn't seem to work on the HD2.
Having searched the forum, I found this update:
http://www.kixass.net/bluepower/
but again, it doesn't seem to work on the HD2.
I know I can create a front screen button to turn on bluetooth, but I will forget to turn it off when I leave the car, and drain the battery (senility )
Anyone help ?
did you install .net cf 3.5 on your hd2??
One of the first things I did !
Interesting app... did you change the settings to ensure that your HD2 uses net cf3.5 at all times? I remember that there were some registry settings that needed to be made to make sure it does not revert back to 2.0 even after installing 3.5
Thanks for the suggestions mouki and eskasi.
Used netcfcfg to ensure 3.5 is used by default (and overidden for the application), but still no joy.
I tried this on a Topaz running a Leo based ROM... no joy too... I suspect its because of WM6.5.... Was your Diamond running a WM6.5 ROM or 6.1?
It was 6.1. I did upgrade to 6.5 when I was messing about with it, but didn't test this app, before I reverted to 6.1.
Maybe Kixass, or some more competent techie than me is lurking, and will see this post, and amend bluepower for 6.5
Maybe it's because the HD2 uses the broadcom Bluetooth Stack, like the Touch Pro2 does, and apparently it's not a proper implementation compared to the original MS Bluetooth drivers and therefore some bluetooth apps break (like BlueInput.. -_-). I think the Topaz and the Blackstone don't use broadcom and so it isn't broken.
are there other solutions to this? I would also like to have the bluetooth on when the phone is on power...