My wife has a Huawei M860 as do I. Anywho, hers has a shattered glass screen. Phone still works.But please know this shattered screen causes such an irritation that it cant be healthy.
Theres no sign of a replacment anytime soon. Pieces of glass are missing now. Question is
Can I remove the glass chunk by chunk and let her just use it without glass till I get a newer phone? Will removing the glass disable whats left of her touch action?
First time posting. Srry if im in the wrong area or breaking rules. Been searching online for hours to no avail.
A message in a bottle
It is possible, but very model-dependent and I'm unsure for your device.
Modern touch phones use a sheet of glass and a thin 'digitiser' layer underneath to register the electrical capacitance of your touches. In some phones these are two separate entities, however in a lot of phones they are 'bonded' together.
Chances are if you're already missing glass pieces, they aren't bonded. I would recommend leaving as much glass in place as you can and possibly sealing the front with clear 'contact' (book cover) or a screen protector, as it affords the digitiser some protection. You don't want to have to replace both if you don't need to.
Good luck!
Just leave it be .You could break your display
Sent from my GT-S5570 using XDA
Thank you for your replies. If I can remove the glass I am not worried about putting the digitizer in danger. Its an old fone that will be replaced all together. I relize if I remove the glass it will be more exsposed.
Thats not the concern. Just wondering if without the glass will it still reconize touch? Not worried about hurting the sensitive display either. I got confidents in my hamd skills. Do things like this all my life. I can be carefull
A message in a bottle
Like I said above, you'll need to research whether the glass and digitiser are fused, or separate entities. If they're separate, you should be fine.
Sent from my HTC Vivid
Like juzz suggested earlier, you should get a screen protector to cover the glass - especially since you mentioned that chunks were missing. There are probably sharp exposed edges that themselves will continue to scratch her.
Thank you all for the advise. Im off to research. Again thxs
A message in a bottle
mythnet00 said:
My wife has a Huawei M860 as do I. Anywho, hers has a shattered glass screen. Phone still works.But please know this shattered screen causes such an irritation that it cant be healthy.
Theres no sign of a replacment anytime soon. Pieces of glass are missing now. Question is
Can I remove the glass chunk by chunk and let her just use it without glass till I get a newer phone? Will removing the glass disable whats left of her touch action?
First time posting. Srry if im in the wrong area or breaking rules. Been searching online for hours to no avail.
A message in a bottle
Click to expand...
Click to collapse
Awesome! Thanks for much for all your hard work
Related
What do I use to remove the scratch? thx.
slikr said:
What do I use to remove the scratch? thx.
Click to expand...
Click to collapse
I see a kit for ipod for that exact thing a few years ago - maybe its worth asking.
i dropped my diamond and the screen has a very nasty looking scratch along the botto of the screen.
please advise what i can do to fix or do i have to replace it for a new touch screen.
if i need a new screen where in th uk is the best place to have it re fitted
thanks
I think it's called Displex scratch remover or similar - try it out it will fill the hairline scratch and make it invisible.
salada2k said:
I think it's called Displex scratch remover or similar - try it out it will fill the hairline scratch and make it invisible.
Click to expand...
Click to collapse
Are you sure this will work? Displex melts a bit of the acrylic plastic on most screens so that it fills up the scratches. Last I heard, the Diamond's screen is glass.
OnePointOh said:
Are you sure this will work? Displex melts a bit of the acrylic plastic on most screens so that it fills up the scratches. Last I heard, the Diamond's screen is glass.
Click to expand...
Click to collapse
If its the screen I'd be carefull applying anything as you risk the display becomes blurred (same reasons thet don't remove scratches on glasses). If it's made of glass maybe consult a car repair shop reparing wind screens. Let's hear what you find out.
OnePointOh said:
Are you sure this will work? Displex melts a bit of the acrylic plastic on most screens so that it fills up the scratches. Last I heard, the Diamond's screen is glass.
Click to expand...
Click to collapse
The outer layer is not glass. It's the layer underneath the digitizer that is glass. Have you noticed that you can indent the screen when you touch it, say, with the stylus? That should prove it for you.
As far as the displex goes I personally haven't tried it as I use a screen protector (which on a side note I have ruined today as my stylus has developed a sharpness that has scratched the crap out of it). So the idea is to replace it when it's gone bad with a new one. If you've scratched the actual outer surface then you could look at replacing it (I'm not sure how you'll go about doing that) or you could try the displex.
Attention: use only on non-coated surfaces and plastics; when used on mobile phones, treat only the transparent portions of the display lens. Not for use with touch screen displays.
JayZee2 said:
Attention: use only on non-coated surfaces and plastics; when used on mobile phones, treat only the transparent portions of the display lens. Not for use with touch screen displays.
Click to expand...
Click to collapse
Uh-oh... Haha I think I recommended Displex to someone before... I've seen people use it on GPS displays and it worked fine, even with touch screen... But if they say no, don't risk it.
looks like it will have to be a new screen,
is the outher screen a seprrate part to the glass section of the screen ??
does anyone know where i can have it replaced in the uk?
If your going to replace it then I'd have a go at polishing it first and see what happens. What you got to loose.
I once used a bit of Brasso on the screen of my car headunit, got the scratches out a treat.
silkw0rm said:
looks like it will have to be a new screen,
is the outher screen a seprrate part to the glass section of the screen ??
does anyone know where i can have it replaced in the uk?
Click to expand...
Click to collapse
If you're going to have a new screen anyway I'd first experiment with some of the various proucts discussed. If it works you save the repair, if not then no harm done as you'l get a new dispaly (at the cost of a new TD likely).
update
managed to get hold of a new screen for a reasonable price too
link
http://www.mobilefun.co.uk/product/17042.htm?referer=FR_PROD-PR-P-17042
now can someone please direct me to where i can have this fitted,
or better still if you know how to change the screen can you please show me instructions of this and tools required.
regards
silkw0rm said:
update
managed to get hold of a new screen for a reasonable price too
link
http://www.mobilefun.co.uk/product/17042.htm?referer=FR_PROD-PR-P-17042
now can someone please direct me to where i can have this fitted,
or better still if you know how to change the screen can you please show me instructions of this and tools required.
regards
Click to expand...
Click to collapse
Search for the tech. manual on the net. It explains step by step how to do it. Good luck with it. I cannot recall where I found it, but even somewhere in xda is a link I think.
http://www.pdacenter.ru/razborka/raz...touch-diamond/
it was in my housing replacement thread before...
very difficult job from what i can tell for replacement
almost as annoying as iphone DIY since it has the most annoying housing ever
this may sound stupid but it is stuff that works
take a piece of microfiber cloth
a banana
toothpaste
and any glass cleaner
1st take a small piece of banana and rub it on the screen for about 3 minutes and take your microfiber cloth and whipe it off... (do not use water) and do not use paper towel or toilet paper!!!!(it will ruin the screen
now flip your microfiber to the clean side and set it down...
take your tooth paste (white colgate is the best) and rub it over the screen for 5 minutes again take the clean side of microfiber and rub off the toothpaste... it will smell minty for a couple of days but eventully it will go away!!!
please try this it works take the time it will work and again do not use any water!!! that means dont put water on cloth and wipe off
hope it helps
htcfanboi said:
this may sound stupid but it is stuff that works
take a piece of microfiber cloth
a banana
toothpaste
[..]
hope it helps
Click to expand...
Click to collapse
Right... I can understand using tooth paste, but a fricking bannana? How funny is that? I honestly would like to see a guy polishing his £350 phone with that.
You've made my day
Ps. I'd suggest using a carrot and then a potato afterwards
COuld be the small amount of acids in it.
A lemon may be too strong. Banana has a fine 'polishing' structure too.
it works man.... banana is my friend......
delicious too
htcfanboi said:
it works man.... banana is my friend......
delicious too
Click to expand...
Click to collapse
Hehe, My apologies then, I'm gonna give it a go as soon as I spot the first scratch
This topic has clues for replacing the screen. I have not concluded an manual for chancing it yet but reading this whole topic gives you the big picture how it is done. Questions are always welcome and I try to answer them with my knowledge. This 1st post gives you 2 links to follow for pics about changing screen and my own starting point for chancing my own screen.
Has anyone bought and installed a digitizer+screen set which is on sale at ebay? I could not post direct link to ebay because I'm a newbie on these forums. You can find the product searching ebay with these keywords "I9000 digitizer". My galaxy's screen cracked and I need an replacement. Both screen and glass broke. I think that this set includes them both. There is also told in the questions that the set infact includes amoled display and not LCD as the title says.
Second question is that does someone have an service manual somewhere. Would be nice to know how to break apart my phone when replacing screen.
Third question is that doesn't samsung vibrant and galaxy s share the same chassis but different screen with more capacitive buttons. Could it be possible to install vibrant's screen to galaxy s?
PS. The way my galaxy brokedown is very funny. I lay down my phone on the kitchen table and the screen cracked. I was like OMFG when I heard the cracking noise. Phone was like 13 days old. Samsung does not repair it with warranty because they think that it wasn't an manufacturing defect. They said that I have dropped my phone and that's the way it broke. That could not be the case because I handled it like a baby. I would have to pay 255€ for new screen and digitizer. Hell no!! I'm a student so that sum does not fit with my wallet.
New screen installed, see posts http://forum.xda-developers.com/showpost.php?p=7683527&postcount=37 and http://forum.xda-developers.com/showpost.php?p=7710572&postcount=40
Edit: Ebay's prices have rised noticeable in the last couple of months. At the moment the price for these screens is around 100$. I found this site which sells them for 60£. http://www.shineyourmobile.co.uk/ProductDetails.aspx?pid=8128
pekkala89 said:
Second question is that does someone have an service manual somewhere. Would be nice to know how to break apart my phone when replacing screen.
Click to expand...
Click to collapse
There are 2 videos on the net, both on youtube I think. Just search "i9000 Disassembly" and you'll find one of them.
The Galaxy S has a serious design flaw as the glass goes around the home button (and the call ear/speaker) so it's very vulnerable there to shattering. I had my phone in the pocket and suddenly when I take it out I see it cracked right next to the home button. What had I done during the time it got cracked? The only possible explanation was carrying a _small_ speaker that then probably hit it. I was so surprised when I saw it cracked because even a speaker hit, when I lifted it up, is hard to consider cracking the screen.
So international model Galaxy S owners, be careful at the bottom and top of the screen. They're the weak points of the glass. For me only the glass cracked and not the screen so it will be interesting to see how much it will cost to fix.
Schmich said:
So international model Galaxy S owners, be careful at the bottom and top of the screen. They're the weak points of the glass. For me only the glass cracked and not the screen so it will be interesting to see how much it will cost to fix.
Click to expand...
Click to collapse
I think that you can't change only the glass. Amoled screen is so thin and I believe it's glued pretty thight to the glass. Separating them may be impossible without tearing the amoled.
the same...
i had a similar unfortunate event ... my screen cracked when i hit the phone to the metallic frame of a chair (it slipped out of my hand )...
it cracked exactly like you people said... near the home button.
i ordered the display + digitizer and i anxiously await its arrival to see if i can replace the damaged one.
it is quite tricky to dissassemble the display part but hope to succed...
keep you posted with the outcome
respect
pekkala89 said:
I think that you can't change only the glass. Amoled screen is so thin and I believe it's glued pretty thight to the glass. Separating them may be impossible without tearing the amoled.
Click to expand...
Click to collapse
Yeah that's my fear but I presume they just heat up the glue. That's how some industries do for other products. I think dental bracers (& its glue) have a different technique as well. So, will be interesting to see.
gallaxya said:
i ordered the display + digitizer and i anxiously await its arrival to see if i can replace the damaged one.
Click to expand...
Click to collapse
Where did you order it from?
If you were asked to pay more than $250 for screen replacement, then why don't you send it to Samsung in Korea? They will replace your SAMOLED for mere USD $100ish and ship it back to you for free (or may be not). This way you get a genium quality from original manufacturer and absolutely no hassles!
I dropped mine from around 4ft onto a concrete floor and its fine. Maybe I just got lucky.
Digitizer+Samoled set ordered from ebay. I should get it in two weeks. If possible I try to take pictures of the changing process and make an manual. I hope it's not glued tight to the chassis.
please do, i have some f***ing little scratches all over the screen, thought it was supposed to be scratch resistant.
Worst part is that it's in it's protective pouch all the time (maybe that's the probleme, dirt/dust might get trapped and rub against the screen).
Got my digitizer and amoled screen t
oday. I will report back if its a hard job or not to replace it.
Sent from my GT-I9000 using XDA App
yrizan said:
Got my digitizer and amoled screen t
oday. I will report back if its a hard job or not to replace it.
Sent from my GT-I9000 using XDA App
Click to expand...
Click to collapse
I tried to remove broken screen for 2 hours and no luck. Removing the motherboard is problematic because power button is glued to the chassis so I could only turn the motherboard aside and not remove it completely. I tried also to remove metal edge but I could only separate it from the left and right edge, not from top and bottom. I hope you have better luck and report how you managed to overcome my problems.
pekkala89 said:
I tried to remove broken screen for 2 hours and no luck. Removing the motherboard is problematic because power button is glued to the chassis so I could only turn the motherboard aside and not remove it completely. I tried also to remove metal edge but I could only separate it from the left and right edge, not from top and bottom. I hope you have better luck and report how you managed to overcome my problems.
Click to expand...
Click to collapse
Sorry to say got in to the same problems
Looks like the phone is build around the screen. Be careful with the metal ring, on top and bottom its between the screen and chassis, so if you brute force to much the screen cracks even more. The screen is glued to the chassis all around with superglue. I am not sure if its even possible to repalce the screen. It let me thinking that samsung wont repair broken galaxys , just replace them.
Ill keep working on the phone and keep trying, but compared to changing the screen on iphone is this like changing the screen on a iphone as a blind man without arms.
People thinking of buying this screen kit on eBay, don't do it. Just contact samsung for a repair.
Ill keep you posted.
I got the screen off.
No need to loosen the metaling ring around. The screen in dropped in the chassis from the front.
On the mainboard, just pop off the screen cable, long and flat next to the SD card slot.
The next step is very strange, just use brute force and crack the screen off the chassis, start from the top
When you get around the home button, be careful. Samsung has clued 2 sensors to the screen and chassis for back and option button. Best thing to do here is bend the screen back a little and cut loos the sensors from the digitizer with a sharp knife/scalpel. Samsung has used insane amount of clue on this phone.
Both the digitizer and amoled screen was clued to the chassis.
The next step is to clean off all the clue, buy loads of glue. Fill the chassis with glue and press the new screen on.
Wish me luck.
Ill keep you posted.
Making me a bit scared reading this thread, I`ve just bought phone Insurance just in case.Good luck fitting your replacement screens, sounds a bit daunting.
YES!!!
New screen in place and everything is working perfectly. Took about 3 hours first time (give or take). Its possible to do it a lot faster. The biggeste problem is the glue. Melting at about 120 celsius, but i was scared to heat the glas as i didnt know how much heat the mainbord could stand. All in all a pain in the a**, but doable.
I can also confirm this screen from ebay to be an orginal samsung amoled screen.
Best of luck too others trying a screen replace.
Sent from my GT-I9000 using XDA App
amoled or samoled though?
My mistake. Its a samoled screen
Sent from my GT-I9000 using XDA App
Awesome!!! thanks for the review
did you manage to snap a few pictures meanwhile you were working in your phone?
Im sorry, no pictures
The charger is missing to my canon camera, new one incomming from ebay. I'll post pictures next time ill change the screen ;-)
Sent from my GT-I9000 using XDA App
I have a samsung infuse from AT&T and recently dropped my phone.
The glass is completely cracked; however, the touch screen is working like normal.
Is there a way to replace the cracked glass only?
If it is possible, does anyone have instructions or a guide on how to fix the cracked glass?
Or, would I just have to file a claim with AT&T Insurance?
Thank you!
Your most likely going to have to claim insurance on your phone from my research the glass is not replaceable !!!
Sent from my SGH-I997 using xda premium
Kdog71588 said:
Your most likely going to have to claim insurance on your phone from my research the glass is not replaceable !!!
Sent from my SGH-I997 using xda premium
Click to expand...
Click to collapse
Really?
https://www.google.com/search?rlz=1...e&ie=UTF-8&q=samsung+infuse+glass+replacement
Well damn guess you can but I guess it depends upon how brave you are to start ripping into your phone and if your comfortable with small electronics
Sent from my SGH-I997 using xda premium
Either of you go through with this yet? Would be curious to hear how it went...
I've looked around online, and everything I'm seeing says the digitizer, LCD, and outer glass are one fused together piece on the Infuse:
http://www.youtube.com/watch?v=MZI6d59ufSc
Even though eBay sellers have the Infuse outer glass for sale separately, it seems like pulling the glass off of the LCD/digitizer without destroying it is going to be extremely difficult. Even if you get the old glass off without damage, you still need to figure out how to attach the new glass to it.
Then what??????
Sent from my SGH-I997 using xda premium powered by The Dark Knight ICS
Kdog71588 said:
Either of you go through with this yet? Would be curious to hear how it went...
I've looked around online, and everything I'm seeing says the digitizer, LCD, and outer glass are one fused together piece on the Infuse:
http://www.youtube.com/watch?v=MZI6d59ufSc
Even though eBay sellers have the Infuse outer glass for sale separately, it seems like pulling the glass off of the LCD/digitizer without destroying it is going to be extremely difficult. Even if you get the old glass off without damage, you still need to figure out how to attach the new glass to it.
Then what??????
Sent from my SGH-I997 using xda premium powered by The Dark Knight ICS
Click to expand...
Click to collapse
http://www.repairsuniverse.com/samsung-infuse-i997-take-apart-repair-guide.html
This must be the instructions to remove outer screen because I have seen a video to replace the digitizer and screen assembly and it just popped off after removing some ribbon cables. I am waiting for outer screen ,outer casing and battery cover to arrive from China. Cost $30 with shipping. Will look brand new on outside if it works. I'll let you guys know how I make out.
Edit....After removing top glass with razor blade as it is fused to LCD with glue I lost response to touch. Ordered new LCD and digitizer with bezel (plastic frame that screen is attached to and circuit board mounts on) . I am not sure if I could get it to work if I could glue or fuse new top glass back on. Scratched the heck out of it anyways. Live and learn, if anyone else had better luck I would like to know.
I had great luck with mine. I started by heating the outer glass with a blow dryer and used a card from a regular deck of playing cards starting from top to bottom of the screen to get it started. After i got it about half way i didn't even use the blow dryer anymore just allot of playing cards. You have to be extremely careful on the top right of the LCD not to damage the ribbon for the digitzer. I got a few minor scratches on the LCD from shards of old glass but you can only see them if the screen is off and you look really hard. It pretty much looks brand new now. I just used thin double sided tape on the outside edges of the new glass for now as i haven't found a permanent way to hold down the glass yet. I will probably leave it that way so next time it breaks i don't have to go through the long process of separating the glass from the LCD again. In my opinion it was well worth the $10 and the labor to replace just the outer glass rather than the $130-$150 for the replacement LCD/digitizer and outer glass.
Thanks for trying.
cbroadsword said:
I had great luck with mine. I started by heating the outer glass with a blow dryer and used a card from a regular deck of playing cards starting from top to bottom of the screen to get it started. After i got it about half way i didn't even use the blow dryer anymore just allot of playing cards. You have to be extremely careful on the top right of the LCD not to damage the ribbon for the digitzer. I got a few minor scratches on the LCD from shards of old glass but you can only see them if the screen is off and you look really hard. It pretty much looks brand new now. I just used thin double sided tape on the outside edges of the new glass for now as i haven't found a permanent way to hold down the glass yet. I will probably leave it that way so next time it breaks i don't have to go through the long process of separating the glass from the LCD again. In my opinion it was well worth the $10 and the labor to replace just the outer glass rather than the $130-$150 for the replacement LCD/digitizer and outer glass.
Click to expand...
Click to collapse
Hey thanks for trying, braveheart. I'm gonna try that too. Dont have a 100 to spend on the pair.
Can you make a guide of that? I think it will help alot of users. You can get pictures from internet and mark the critical points which will help in separation.
broken screen. Help!!! .
Month back, dropped my phone(2-3 times).
Now stuck with unusable mobile.
Can somebody suggest,where I can get its lcd [email protected]+ digitilizer, on cheap price.
The screen on my Skyrocket became recently cracked. The cracks begin at the very top and make really small, tight cracks, then it spiderwebs down the front of the phone into bigger pieces of glass. Towards the top, the smaller pieces of glass have begun to fall out. It's not really dangerous, but I am kinda nervous of cutting my finger one of these times.
I've been searching on Google and Youtube to find an answer to my question, but I can't seem to find a real, definitive answer. I want to know if the glass/lens of the digitizer can be safely removed from the rest of the digitizer?
I know all the tricks of using a heat gun, and a little scraper, but I also heard that the digitizer itself is like 1mm thick and VERY delicate?
So I went ahead and bought the glass off of Ebay for like $7. Then I received the glass in the mail, and got kinda apprehensive of doing it.
Another question: If I successfully remove all the old glass, how do I secure the new lens to the digitizer? Is there some sort of glue I need, or is it friction from the chrome trim ring?
Yupp i think it can be done
Sent from my Renovate HTC
Afrojoe said:
Yupp i think it can be done
Sent from my Renovate HTC
Click to expand...
Click to collapse
Damn. You got that research and stuff?
demonblod said:
The screen on my Skyrocket became recently cracked. The cracks begin at the very top and make really small, tight cracks, then it spiderwebs down the front of the phone into bigger pieces of glass. Towards the top, the smaller pieces of glass have begun to fall out. It's not really dangerous, but I am kinda nervous of cutting my finger one of these times.
I've been searching on Google and Youtube to find an answer to my question, but I can't seem to find a real, definitive answer. I want to know if the glass/lens of the digitizer can be safely removed from the rest of the digitizer?
I know all the tricks of using a heat gun, and a little scraper, but I also heard that the digitizer itself is like 1mm thick and VERY delicate?
So I went ahead and bought the glass off of Ebay for like $7. Then I received the glass in the mail, and got kinda apprehensive of doing it.
Another question: If I successfully remove all the old glass, how do I secure the new lens to the digitizer? Is there some sort of glue I need, or is it friction from the chrome trim ring?
Click to expand...
Click to collapse
Good luck man.....i tried and its a PITA!!!! Haha my dumbass ended up cracking my digitizer/LCD so i had to shell out another $130 for a new one......i hope u have better luck than me tho.....
Sent from my SGH-I727 using xda app-developers app
jyazzie110 said:
Good luck man.....i tried and its a PITA!!!! Haha my dumbass ended up cracking my digitizer/LCD so i had to shell out another $130 for a new one......i hope u have better luck than me tho.....
Sent from my SGH-I727 using xda app-developers app
Click to expand...
Click to collapse
That's EXACTLY what I'm worried about. But I guess my screen is done for either way. It's terribly cracked and falling apart now, so it can't get much worse.
demonblod said:
That's EXACTLY what I'm worried about. But I guess my screen is done for either way. It's terribly cracked and falling apart now, so it can't get much worse.
Click to expand...
Click to collapse
In the accessories section a guy claims to have done it and used double sided tape to put the glass back on......idk tho i heated it up so much i burned my finger wen i touched the glass and i still couldn't separate it from the digitizer.....id say just buy a new digitizer......it isnt hard to replace.....i bought the digitizer alone without the housing around it and saved about $25.....
Sent from my SGH-I727 using xda app-developers app
Nope. It didn't work. I broke it. I kept using my heatgun, but the stupid adhesive just wouldn't give up. I turned up the heat a little bit, and suddenly a section of the digitizer just blew up into a dull green color. I guess that means I fried the pixels. Even after I burned the digitizer, the adhesive was still very strong. I think this is actually impossible. In order to loosen the adhesive, you would have to achieve a temperature far past the point of damaging the digitizer.
Another concept:
I had MANY small pieces of glass. I kept thinking "I wish I had nice, big pieces of glass. Then this would go so much faster". When I did try to lift a larger chunk of glass, the combined tension of the adhesive over the whole surface area caused the piece of glass to flex and crack.
So when you try to remove a large piece of glass, it then breaks into a hundred tiny pieces of glass and you're screwed even more.
demonblod said:
Nope. It didn't work. I broke it. I kept using my heatgun, but the stupid adhesive just wouldn't give up. I turned up the heat a little bit, and suddenly a section of the digitizer just blew up into a dull green color. I guess that means I fried the pixels. Even after I burned the digitizer, the adhesive was still very strong. I think this is actually impossible. In order to loosen the adhesive, you would have to achieve a temperature far past the point of damaging the digitizer.
Another concept:
I had MANY small pieces of glass. I kept thinking "I wish I had nice, big pieces of glass. Then this would go so much faster". When I did try to lift a larger chunk of glass, the combined tension of the adhesive over the whole surface area caused the piece of glass to flex and crack.
So when you try to remove a large piece of glass, it then breaks into a hundred tiny pieces of glass and you're screwed even more.
Click to expand...
Click to collapse
Exactly wat happened to me.....so u gettn a new digitizer or just a whole new phone?
Sent from my SGH-I727 using xda app-developers app
hi
i want to know if only the exterior glass of nexus 5 can be replaced. My phone has a cracked screen but the touch response, colors etc everything works fine so only the outer glass (gorilla glass?) is damaged. I want to know if only that can be replaced as LG ask around 150$ to replace the whole component.
can i order this? is this possible?
http://www.ebay.com/itm/C-Front-Out...-Google-Nexus-5-D820-D821-Tools-/171311153201
Thanks
Bump??
im pretty sure they are fused together and if you replace 1, you replace both.
Unfortunately you will have to replace the whole thing. When my screen broke It was functional completely aside from the proximity sensor (due to shattered glass). I tried taking it apart afterwards to no avail.
Well, you'll maybe be able to replace only the touch screen (without the LCD) but it wwill not be easy has you'll probably need to heat it to be able to remove the glue, etc.
Probably better to buy a lcd + touch screen :/
ohh
so the ebay item i linked is completely useless?
Thanks for your help guys
It's not impossible to try and replace only the glass. A friend of mine has done this with his galaxy note, which also has a glued screen+digitizer+glass assembly. However, the replacement glass is pretty bad and reflective and dust has started gathering beneath it. The touchscreen was also affected: some areas don't respond so well anymore.
I've replaced just the glass on a different phone. It's the biggest pain ever. You'd have to separate the glass via a heat gun, while trying not to break the digitizer. Then remove the glue. Then adhere the new glass to the digitizer with loca adhesive. Loca is hard to deal with, bubbles, and can get into other components ruining them. It must be cured with a uv light. And even if you can pull it off, no way will it be 100%. Strange glares and whatnot. Some try to do it with double sided tape, but that leaves a gap between the glass and digitizer, which causes strange touch responses or it'll be totally unresponsive. And be prone to break the glass easily without loca. Trust me pay the $150 and let lg replace the whole assembly.
Lokke9191 said:
I've replaced just the glass on a different phone. It's the biggest pain ever. You'd have to separate the glass via a heat gun, while trying not to break the digitizer. Then remove the glue. Then adhere the new glass to the digitizer with loca adhesive. Loca is hard to deal with, bubbles, and can get into other components ruining them. It must be cured with a uv light. And even if you can pull it off, no way will it be 100%. Strange glares and whatnot. Some try to do it with double sided tape, but that leaves a gap between the glass and digitizer, which causes strange touch responses or it'll be totally unresponsive. And be prone to break the glass easily without loca. Trust me pay the $150 and let lg replace the whole assembly.
Click to expand...
Click to collapse
It's too bad it's like this. Probably the most likely thing to break on a phone and they make it so difficult to fix and compared to the price of the phone, expensive to fix. Certain things should just be easily fixable. Oh well, such is life.