Messing around with odin.. big mistake - Verizon Droid Charge

My phone was acting up so I decided to odin back to stock and take it from there...
However, while odin'ing back (using http://forum.xda-developers.com/showthread.php?t=1111486) the process stalled at factoryfs or somethin like that so I searched around and found this thread http://forum.xda-developers.com/showthread.php?t=928191 where apparently the same thing happened. So OP said they unplugged and plugged back in and reflashed and got it working. I tried this, but I can't get the phone back into dl mode or to boot or to even charge I'm guessing. Wtf happened?
The battery was in if it matters for anything

Make sure when your in Odin , and you click PDA , that you right click on cI510_vzw .... that you right click on it and click " extract here" . Then select the PIT file and make sure repartition is the only thing checked. I just went through the same thing 5 mins ago and I have it back up running
Sent from my VS910 4G using XDA

And I had to leave battery out , volume down while plugging in usb to get into download mode. don't forget to put battery back in
Sent from my VS910 4G using XDA

I had everything in odin running correctly I'm pretty sure. Only repartition was checked, the md5 file was the one running through odin. I unplugged it while it was flashing and I can't get back into download mode (holding vol key down) and the phone won't power on.

Don't check the "repartition" checkbox unless you have the PIT file selected. You more than likely wiped out the partition information on the phone when you did that.
And another thing... doing a repartition with the PIT file isn't always necessary, it's only needed a small 5% of the time.
Do you need a good clean download of the EP4D ODIN image?

trparky said:
Don't check the "repartition" checkbox unless you have the PIT file selected. You more than likely wiped out the partition information on the phone when you did that.
And another thing... doing a repartition with the PIT file isn't always necessary, it's only needed a small 5% of the time.
Do you need a good clean download of the EP4D ODIN image?
Click to expand...
Click to collapse
I believe that Odin stops if you don't have a PIT file and select repartition.

It stopped me several times but I finally got it figured out . It wouldn't flash without a pit file selected with repartition selected
Sent from my SCH-I510 using XDA

It's time to give Verizon a call and get a replacement.

The short answer is you need to take the phone into verizon and get a replacement. Rule number 1 of Odin is you never unplug the phone while it's flashing. Sorry that it happened. :/

Endless2232 said:
The short answer is you need to take the phone into verizon and get a replacement. Rule number 1 of Odin is you never unplug the phone while it's flashing. Sorry that it happened. :/
Click to expand...
Click to collapse
Went ahead and did that today... Apparently I'm going to get a CPO phone because the CS lady on the phone said it happened because I downloaded an app.... Sigh. Thanks for the replies.

Glad they treated you good LOL I got someone who was an asshole
Sent from my SCH-I510 using XDA

Hovo said:
Went ahead and did that today... Apparently I'm going to get a CPO phone because the CS lady on the phone said it happened because I downloaded an app.... Sigh. Thanks for the replies.
Click to expand...
Click to collapse
Verizon is not going to give you a brand new phone, unless you're 15 days since you purchase the device. After 15 days, every replacement will be CPO.

haha I learned the never unplug a device while it is flashing with my old ipod video 5g. Funny thing is itunes locked up in the middle of the flash... Dead as a door nail. Damn you crapple.

Glad you got a replacement. I had the same kind of thing happen to me, thought I was screwed. However, I took my sd card out and plug it into a card reader on my laptop. Put the eclipse ROM directly on it and reinstalled card back into my phone. Booted into CWM reinstalled ROM and worked like a charm. Just for future reference it's worth a shot. Or if you just want to keep your phone.

Related

Samsung Droid Charge Bricked

ok droid charge was rooted went to restore back to stock unrooted (was going to sell it) tried to flash using Odin with the pit file and stock one Odin went about half way and had a error phone turned off i tried to get the phone back into download mode to restart the process but i can't get the phone into download mode also i can't get the phone to boot up no Samsung logo nothing any help would be greatly appreciated the phone will not do anything at all i need help i have tried p3 Samsung pst method but still nothing
thanks
dustin4863 said:
ok droid charge was rooted went to restore back to stock unrooted (was going to sell it) tried to flash using Odin with the pit file and stock one Odin went about half way and had a error phone turned off i tried to get the phone back into download mode to restart the process but i can't get the phone into download mode also i can't get the phone to boot up no Samsung logo nothing any help would be greatly appreciated the phone will not do anything at all i need help i have tried p3 Samsung pst method but still nothing
thanks
Click to expand...
Click to collapse
just curious what methode are you using to enter download mode? Did you try recovery for giggles?
i have tried both download mode and recovery and just trying to let it boot up normal and it will not do anything in all three just a black dead screen
Try leaving the battery in when you go to download mode. Also leave it in when flashing.
if it wont even power on in any way or go into the download mode you might be bricked...I did this before and I had to exchange it at Verizon..luckily since it wouldnt turn on they couldnt tell what I did to it...hope you can get your issue resolved
Ha a true brick. Finally someone using the terminology correctly. A buddy of mine has this happen with his galaxy s. He got it exchanged in store no questions asked. btw Sorry to hear about your phone
Sent from my ADR6350 using XDA App
1/2 Brick
Hi
Sorry to hear about your issue. I am at half brick now. Been at multiple spots learning here but never completely no visability! 3/4, 7/8, right now in a flash it does not see my phone (no network) data side is fine but can not get or receive calls. It is not the SIM card (according to VZW). Data side works fine 4G etc, emails but no phone. A great PDA but not a phone. No one has answers but I belive to be a cp_modem.bin issue download hangs at around 98% in what does a boot 2nd boot on the screen in the download then says:
Wait, VIA Booting ..
VIA rest done. ..
Downloading to VIA...
To everyone the {Kangfuscius.tar} has helped me when I thought all hope was lost, even in a partial download it helped to bring me back.
Any suggestions on files for the phone tab in ODIN all I can think of is, it can't get worse. The FEDEX guy kow knows me by name between the Fascinate's and now I guess the Charge.
Any help appreciated,
norm883
norm883 said:
Hi
Sorry to hear about your issue. I am at half brick now. Been at multiple spots learning here but never completely no visability! 3/4, 7/8, right now in a flash it does not see my phone (no network) data side is fine but can not get or receive calls. It is not the SIM card (according to VZW). Data side works fine 4G etc, emails but no phone. A great PDA but not a phone. No one has answers but I belive to be a cp_modem.bin issue download hangs at around 98% in what does a boot 2nd boot on the screen in the download then says:
Wait, VIA Booting ..
VIA rest done. ..
Downloading to VIA...
To everyone the {Kangfuscius.tar} has helped me when I thought all hope was lost, even in a partial download it helped to bring me back.
Any suggestions on files for the phone tab in ODIN all I can think of is, it can't get worse. The FEDEX guy kow knows me by name between the Fascinate's and now I guess the Charge.
Any help appreciated,
norm883
Click to expand...
Click to collapse
I don't know why your phone is booting into 'VIA' mode and don't even know what that is so I couldn't say a fix other than odining the usual stock rom/pit combo (leaving the battery in when flashing in odin also and uncheck the 'auto reboot' option)... also phone tab/button is NOT supposed to be touched in odin, only PDA, PIT if needed, and Start
Where did it fail in the Odin flash? The only way you should be bricked is if it failed while flashing boot.bin or sbl.bin, otherwise, it should still go to download mode. Have you tried using one of the Force Download Mode jigs/dongles that the GSM models use to get into download mode?
i don't recall where it failed at but it will not not respond to anything with batt or without where can i find the gsm software i will give it a try before i call insurance a link or anything would be great
what gsm models are equivalent to the charge
dustin4863 said:
i don't recall where it failed at but it will not not respond to anything with batt or without where can i find the gsm software i will give it a try before i call insurance a link or anything would be great
what gsm models are equivalent to the charge
Click to expand...
Click to collapse
Infuse 4g or SGS 2 unlocked.
Sleek69 said:
Infuse 4g or SGS 2 unlocked.
Click to expand...
Click to collapse
SGS2 is not equivalent. Just search for galaxy s download jig and i'm sure you'll find what I'm talking about. It is the same thing for all the SGS phones, and some have said it works on the 4G versions of the phones as well.
dustin4863 said:
ok droid charge was rooted went to restore back to stock unrooted (was going to sell it) tried to flash using Odin with the pit file and stock one Odin went about half way and had a error phone turned off i tried to get the phone back into download mode to restart the process but i can't get the phone into download mode also i can't get the phone to boot up no Samsung logo nothing any help would be greatly appreciated the phone will not do anything at all i need help i have tried p3 Samsung pst method but still nothing
thanks
Click to expand...
Click to collapse
Hi, I had the same thing happen to my first Charge. I could not boot my phone even to the samsung logo, so I searched around the Internet. Somehow I think it was the Captivate trick worked. I took out sim, battery, sdcard>plugged in usb to computer>held up and down volume together>put in battery; miraculously it went to download. I tried every other combination beforehand and none worked, so I know this method works.
Unfortunately this was before we had IMNUTS Pit file and a odin flash would not change anything so I could not recover and I flashed a Pit that was not for the Charge. Wrong answer! After that it was in the non-boot state again but the same method above would not work any longer. If your phone does not work with the method above, maybe something went wrong with the repartition and pit file. That is just a guess though!
well the jig hasn't worked yet i am running right at 300k tomorrow i am going to get a 1k and add that in also and see if that helps. also pulling all the cards and the battery didn't work either. this is not looking good i am up for any ideas that anyone has
thanks
dustin
Hey guys found a way to unbrick Samsung droid charge and revert back to stock.
1. Download and install Odin found here ( http://forum.xda-developers.com/show....php?t=1085190 ) unzip and open
2.Download this file and unzip ( CI510_VZW_EE4_ALL_ONE-LTE-CP_REV03_user_CL1014954.tar.md5.7z) from here ( http://www.multiupload.com/6WJ2SFUKO6 ) or original thread where i found this file is from here ( http://androidflip.com/android-2-3-4...talling-guide/ )
3. set phone to download mode, do this by taking battery of phone, plug phone into computer and hold Volume down, a Yellow triangle with a working android will appear.
4. Click on odin you will see your phone come up under ID:COM, now do not click on anywhere but on PDA thats where you will have to find the file you downloaded on step 2 and make sure is the unzipped file. once u find it, click on open then start.
5. Be patient this can take up some time, once is done the box will turn green and say pass, at this time your phone will no longer have the Yellow triangle and you can unplug and place the battery back in and turn phone on.. once again be patient when turning phone on it will take a little while to complete.
i tried this and it does work, my Droid charge was bricked and now it works.
Thanks to xda-developers where i was able to find odin and also thanks to androidflip.com where i was able to find the Droid Charge stock rom to flash it back using odin.
Hope this helped everyone needing help.
dustin4863 said:
well the jig hasn't worked yet i am running right at 300k tomorrow i am going to get a 1k and add that in also and see if that helps. also pulling all the cards and the battery didn't work either. this is not looking good i am up for any ideas that anyone has
thanks
dustin
Click to expand...
Click to collapse
Dustin, were you able to get it working? I'm in the same boat. Right after boot.bin it failed. Which was within seconds after hitting the start button in Odin. Verizon won't honor my warranty, because I didn't buy the phone from them.
Hard Brick Fixed
If you are truly hard bricked (no download mode, no power, no nothing), you can get it fixed for $40 at mobiletechvideos.com. I flashed a file that didn't work unless I took off the md5 extension. Big mistake. After trying absolutely everything, including surfing the internet for a day, spending almost $20 to get 2 day delivery for a USB Jig that did absolutely nothing, I sent my phone to mobiletechvideos.com. Josh brought it back from the dead; don't know how, but it was the best $40 I ever spent! I think there aren't any reviews because there haven't been enough newbies like me who just can't wait for Gingerbread and bricked their Samsung Charge. Putting my review there tonight...should be first one. The reviews from all the other phones he has unbricked convinced me to try and I'm glad I did.
Many people have hard bricked their phones trying to downgrade. Give the jig a shot, but don't hold out much hope.
Personally I think there is something being overlooked during the downgrade process... Too many people are hard-bricking during the process for it to be coincidence.
Oh yes
mgsparro said:
If you are truly hard bricked (no download mode, no power, no nothing), you can get it fixed for $40 at mobiletechvideos.com. I flashed a file that didn't work unless I took off the md5 extension. Big mistake. After trying absolutely everything, including surfing the internet for a day, spending almost $20 to get 2 day delivery for a USB Jig that did absolutely nothing, I sent my phone to mobiletechvideos.com. Josh brought it back from the dead; don't know how, but it was the best $40 I ever spent! I think there aren't any reviews because there haven't been enough newbies like me who just can't wait for Gingerbread and bricked their Samsung Charge. Putting my review there tonight...should be first one. The reviews from all the other phones he has unbricked convinced me to try and I'm glad I did.
Click to expand...
Click to collapse
Doing so NOW! For the same issue. My PC decided to spontaneously reboot during ODIN while flashing a ROM on My Droid Charge. Josh was quick to respond to EVERY single annoying question I had about their service. So I am doing so. If it works, I'll tell you, I'm adding a link to their site in my signature on every forum I'm a member of, even forums I have for my daughter's schooling hahaha! They deserve the references just for being quick to respond. Thanks for the info man, props to you.

ODIN doesn't actually install Files

ODIN doesn't seem to want to install any kind of odin file that I put into it on my phone.
It gets stuck at dbdata.rfs and then it just remains there for over 2 minutes.
Tried to pop the battery back in once it got there, but that didn't work either.
Also can't get into recovery, by pressing volume down + power key.
You should know my phone died 2 days ago, and I used ODIN to bring it back to life. By died I mean it would bootloop to the recovery and then it finally gave me the bootloader=7 error after which it would just boot into the samsung recovery and nothing else.
Does this mean I will be stuck with a phone that I cannot root or backup or even install a custom rom?
thizzmaster said:
ODIN doesn't seem to want to install any kind of odin file that I put into it on my phone.
It gets stuck at dbdata.rfs and then it just remains there for over 2 minutes.
Tried to pop the battery back in once it got there, but that didn't work either.
Also can't get into recovery, by pressing volume down + power key.
You should know my phone died 2 days ago, and I used ODIN to bring it back to life. By died I mean it would bootloop to the recovery and then it finally gave me the bootloader=7 error after which it would just boot into the samsung recovery and nothing else.
Does this mean I will be stuck with a phone that I cannot root or backup or even install a custom rom?
Click to expand...
Click to collapse
try leaving the battery in for the whole flash, also recovery is volume up+home button+power
blazing through on my 4G Droid Charge
I also tried leaving the battery in for the whole flash process as well, for some reason ODIN is super slow even on my comp which is not the least bit slow for the specs(3.8ghz amd 545 with 4 gb of ram ddr1666) so I do not know why it would be so slow either. when the flash is done it says 134:00 minutes and whatever rom I flash doesn't actually get flashed, it just sticks to the stock ram.
i can't even install a recovery on the phone either, and can't even get root for some reason, maybe the one click root i am using might be outdated or something.
actually just tried to do the recovery mode, but it only got me to the samsung recovery not the clockworkmod recovery. even after I had a successful flash of the odin for the recovery portion.
Are you using the PDA section? Leaving repartition UNchecked?
i was using the phone section, but whats the difference, isn't it all the same? and yes i was leaving the partition unchecked.
thizzmaster said:
i was using the phone section, but whats the difference, isn't it all the same? and yes i was leaving the partition unchecked.
Click to expand...
Click to collapse
that's your problem right there, DO NOT use any section except PDA and PIT for flashing stuff with Odin... try again with it in PDA and you should be able to boot into it and it'll work fine
PHONE SECTION = BAD! NEVER EVER use the phone section! It can cause some seriously bad issues, the most problematic being the infamous brick(unrecoverable).
thizzmaster said:
maybe the one click root i am using might be outdated or something.
Click to expand...
Click to collapse
These don't work for the Charge.
Sent from my Droid Charge running GummyCharged 2.0
thizzmaster said:
i was using the phone section, but whats the difference, isn't it all the same? and yes i was leaving the partition unchecked.
Click to expand...
Click to collapse
...Have you not read ANY of the tutorials??? If you want to brick you're phone (you'd be one of the few and the proud, because you really have to try to do it), then keep on using the phone section and have a $500 paperweight.
hazard209 said:
...Have you not read ANY of the tutorials??? If you want to brick you're phone (you'd be one of the few and the proud, because you really have to try to do it), then keep on using the phone section and have a $500 paperweight.
Click to expand...
Click to collapse
Haha. We should let him brick it.
Sent from my Droid Charge running GummyCharged 2.0
That was a little mean on my part... But come on people, please read thoroughly through the tutorials, how to's, and OPs before posting about a problem. Actually even before doing ANYTHING to your phone. Use the search, it's there for a reason. Users and Devs have taken the time to compile all of this for you and you've just wasted their time and insulted them by ignoring it.
Ok. Done ranting. Thizzmaster, sorry for the outburst. For future reference always use the PDA section for .tar.md5 files for your Charge. It matters and there is a difference.
Last time i checked, Most of these superphones are actually super pda's with phone capabilities.

[Q] S II Epic Touch 4G ODIN Re-partition issue.

I have majorly screwed up, I think.
1) Tried to root my phone.
2) Ran ODIN.
3) Accidentally had the "Re-partiton" tab checked and pressed Start.
4) ODIN hung for a while and then closed.
5) Now my phone will just do nothing. Bricked ??
6) If i power on, i see the blue light but the screen stays blank
7) I have taken out the batt as well but nothing.
8) I was trying to get i back to download mode but the light goes blue like the phone is turning on and then it blinks once and stays blue. And the screen is still blank.
Any help on what I can do at this point ?
I have tried to plug in the USB and see if ODIN recognizes it at all but nothing.
Damn Default Re-Partition in ODIN
Same thing happened to me. Had my phone rooted fine and was flashing new Clockwork Kern and Epic Touch 4G .pit I did the same thing. Done everything and still can't find a solution. Please Help? Thanks!
I did the same exact thing with the same result. Have you guys found a solution yet? I feel so stupid for not realizing I did that.
I am so sorry.....but your phones have died .
Sent from my GT-S5830 using XDA App
There IS a PIT file somewhere around here that could help you out if you repartition with the PIT file and also at the same time flash a recovery/stock ROM. Worst case, buy a USB JIG to force the phone into download mode.
Product F(RED) said:
buy a USB JIG to force the phone into download mode.
Click to expand...
Click to collapse
I just bought one last night, waiting for it to come in the mail. I'll post results after I use it.
Well, while waiting for my jig to come in the mail I figured I'd give going to Sprint a shot. I brought in my phone, apparently since I had activated the phone, my insurance carried over to it. They asked me if I could leave it for two hours so I did. Since I essentially wiped the hard drive they couldn't find out why it wouldn't turn on and just gave me a new one. Problem solved.

How I fixed my totally bricked Infuse

Here's the scenario.
I flashed AOKPb40 when I wasn't home. My phone was stuck on the Samsung boot screen. I tried 3 finger recov... no good. Still stuck on boot screen. Removed battery, waited a few minutes, 3 finger... still stuck on boot screen. I figured I'd wait till I get home and Odin back to stock. By time I got home my battery was dead. It wouldn't charge. It was on the charger for 2 hours and no go. I plugged the USB into PC and entered download mode. I figured what the hell... lets give it a shot. Launched Odin, started JScotts UCLB-Root-Modded Odin Package. Everything was running then... boom. Phone shut down right in the middle of FACTORYRFS. Pulled battery and tried the whole thing again... guess what... same thing. So I put my phone back on the charger and my screen showed a phone icon with a triangle with an exlcamation point and a PC icon. I thought "Oh Crap".
So here is how I fixed it.
I downloaded qkster's Heimdall One-Click package. I read up on how to use Heimdall and I was taken to a download page to download Heimdall suite. After many failed attempts to load the Heimdall package in Heimdall Front End, I kept getting a file size error. I googled the error and found qkster's re: to a guy with the same problem. Turns out the One-Click package is self executable, no need for the Heimdall front end suite. So I launched qkster's Heimdall package and it actually completed the flash! However, when the phone rebooted I was shown a partial CWM recov menu. I hit reboot and it kept taking me to the same CWM menu.
Now that I can get past the screen with the phone-caution-pc thing I tried using Odin with JScott's UCLB package. Odin finally worked all the way through, but with the same result as Heimdall, CWM Recov loop. I figured I was missing boot loaders. Flashed through Odin and still no good.
I now went all the way back to stock using GTG's Ultimate Unbrick. Voila! My phone is back! Holy toledo, 4 hours of trouble shooting and I finally have a working phone again.
Summary, Odin doesn't complete and you're stuck, here's what to do.
Use qksters Heimdall
http://forum.xda-developers.com/showthread.php?t=1629079
If stuck in Recov loop. Use GTG's Ultimate Unbrick
http://forum.xda-developers.com/showthread.php?t=1116251
I hope my long painful recovery story will help someone out.
Sounds like you just needed an unbrick solution with a pit file for repartition. You could have used just the UCLB3 Unbrick with the pit file, and you would have been set.
http://forum.xda-developers.com/showthread.php?t=1705260
Still, glad you worked it out. This is why it's a good thing that we have many options that work via Heimdall and Odin. When one isn't doing it on your phone, just try another. We just have to be careful not to call our way of fixing it the only right way or the best way. Several ways exist, so we truly have an unbrickable device. Well, unbrickable as long as you don't bork a bootloader flash.
Edit: By the way, that phone-caution-pc thing is still download mode.
Sent from my SGH-I997 using Tapatalk 2
Well said jscott, and glad you got it working. I would also add, that it would appear from the initial symptoms, that maybe you just lost recovery. Several roms, including uniporn have packages that can fix that. In the uniporn thread it is in post 3.
Also, I think there is a good lesson here too for others and that would be that it would be extremely wise to know your way around Odin and heimdall before embarking on that very first flash.
Again, this is just for future reference should someone read this later on. Glad to hear you are back up and running.
Sent from my SGH-I997 using Tapatalk 2
Good work.
As Yuma have stated, when you lost recovery, flashing this kernel would have brought you back to working cwm to flash the rom also:
http://forum.xda-developers.com/showpost.php?p=25526654&postcount=3
And when you have completed the uclb3, you could have finished it with the boot loader flash and then do a factory reset. After that, flash which every insecure kernel to get back recovery to flash what ever you wanted.
As long as you can get back into download mode, you can use any of the restore process.
Thanks all for the follow up. The biggest problem was the dead battery. After I finally got this sicker up and running with the phone plugged in my battery was at 8%. The damn thing kept crashing while in download mode. But yes, this is not the only way. I had to use qksters heimdall to at least get the phone to boot. Once I got to boot into the recovery boot loop issue I used gtg unbrick.
If it wasn't for all the posts and threads from you guys I would've been screwed. Oh, and to top it all off, xda was down when I first started down the road. Long freaking day!
Sent from my SGH-I997 using xda premium
I've been in that situation. Easiest solution is to just get a fully charged battery
Sent from my SGH-I997
jscott30 said:
Sounds like you just needed an unbrick solution with a pit file for repartition. You could have used just the UCLB3 Unbrick with the pit file, and you would have been set.
http://forum.xda-developers.com/showthread.php?t=1705260
Still, glad you worked it out. This is why it's a good thing that we have many options that work via Heimdall and Odin. When one isn't doing it on your phone, just try another. We just have to be careful not to call our way of fixing it the only right way or the best way. Several ways exist, so we truly have an unbrickable device. Well, unbrickable as long as you don't bork a bootloader flash.
Edit: By the way, that phone-caution-pc thing is still download mode.
Sent from my SGH-I997 using Tapatalk 2
Click to expand...
Click to collapse
The first problem I had was Odin was crashing during the factoryrfs stage. That's why I tried heimdall. I just needed something to get loaded so I could start flashing. I didn't think about going straight to uclb, would've saved me a step or two
Sent from my SGH-I997 using xda premium
tx240sx said:
The first problem I had was Odin was crashing during the factoryrfs stage. That's why I tried heimdall. I just needed something to get loaded so I could start flashing. I didn't think about going straight to uclb, would've saved me a step or two
Sent from my SGH-I997 using xda premium
Click to expand...
Click to collapse
If you were using something like my earlier rooted UCLB3 Odin options, those don't have a pit. Those aren't intended as much as an unbrick/restore option as they are for a quick way to get to rooted UCLB3. Hanging on factoryfs.rfs suggests you needed repartitioning, and the UCLB3 Unbrick provides this, since it has a pit file. The other Odin package wasn't working because you needed a pit file to restore in your situation. That's why the GTG Unbrick ended up fully restoring your phone; it has a pit. It or the UCLB3 Unbrick should have worked to "unbrick" your phone right after the first failed Odin attempt. Also, as noted by Yuma and qkster, an option available before that first Odin flash was to restore just the kernel/recovery. That option became unavailable after the first failed Odin flash. Still, many options are available, and we're glad you found a combination that worked.
Sent from my SAMSUNG-SGH-I997 using Tapatalk 2
infuse reboot?????
is there an easier way to fix this issue? Honestly I could care less about the phone I have over 1000 pictures and videos I would like to save. is there a way to ge them off of the phones memory with it rebooting over and over?
You might be better off starting your own thread and give some details like what is phone doing, which ROM, what did you try to fix it, etc.
Sent from my SGH-I997 using xda premium
infuse rebooting
psal217050 said:
You might be better off starting your own thread and give some details like what is phone doing, which ROM, what did you try to fix it, etc.
Sent from my SGH-I997 using xda premium
Click to expand...
Click to collapse
I have done everythig possible that can be done taking the battery out, charging it from wall charger and charging it from usb port. letting it wait for 2 days before messing with it. One day it went one step further to the white screen where the at&t logo forms and then it reboots again. I have not done a master reset or whatever its called because I want my pics of videos and contacts. The phone has been in the otter box from day one so it looks brand new and its over a year old. I could care less about the phone once I get my pics and videos off of it I will not mess with it again. Is it possible to save pics videos and contacts? I am not sure what you mean when you ask which ROM.
rocafella23 said:
I have done everythig possible that can be done taking the battery out, charging it from wall charger and charging it from usb port. letting it wait for 2 days before messing with it. One day it went one step further to the white screen where the at&t logo forms and then it reboots again. I have not done a master reset or whatever its called because I want my pics of videos and contacts. The phone has been in the otter box from day one so it looks brand new and its over a year old. I could care less about the phone once I get my pics and videos off of it I will not mess with it again. Is it possible to save pics videos and contacts? I am not sure what you mean when you ask which ROM.
Click to expand...
Click to collapse
Okay, since you don't want to do your own thread. Read the information in the following link and follow it to the letter. This should put you back to stock and if everything works right, you will be able to get your info off the phone.
http://forum.xda-developers.com/showthread.php?t=1524081
If you don't know how to put the phone in download mode, take your battery out, hold down the volume +/- buttons but no power button, put the batter back in and then plug the USB (connected to a computer that has the drivers from the link installed) into the phone. Do not disconnect the phone otherwise, you may end up with a brick.

[Q] Soft Brick Help

Alright, first off, PLEASE DON'T MURDER ME. I've been researching for hours and can't come up with a fix. My buddy was doing something stupid to his Droid Charge and soft bricked it. I'm a webOS guy, so I don't know much about rooting on android, and I don't belong here, but I'm usually pretty good at fixing stuff. Not this. I don't know what he did.
With the battery in, you can't do anything. With it out and plugged in to the pc, you can push vol down to get to downloading mode. I tried some java program OneClick, didn't work. I tried Odin, that was confusing as heck. Under PDA I got the charge's tar, but it wouldn't go past initializing.
Anyone willing to step by step troubleshoot with me? He's paying me to fix it, I can split it via paypal? (Am I allowed to say that?) Just feel bad, he's going on vacation tomorrow. Fail.
OK first download this: http://www.imnuts.org/downloads/cha...L_ONE-LTE-CP_REV03_user_CL706183_ship.tar.md5
Open ODIN, plug in phone with download mode. Once phone is in download mode, put in the battery. Click PDA and put that .md5 file in. Make sure that bootloader, phone, and csc are unchecked.
Check Auto Reboot and F. Reset Time. Everything else (besides PDA) should be unchecked. Hit start, and it should finish in like 5 minutes and boot up by itself. There will be two OTA updates he will have to get.
Also make sure to put the battery back in before flashing.
Sent from my SCH-I510 using Xparent Red Tapatalk 2
http://www.imnuts.org/downloads/charge/odin/charge.pit. He may also need this pit file that goes in the pit section of Odin. Good luck.
Sent from my Galaxy Nexus using xda premium
Please help, this pit may have hard bricked my phone
sasquatch080 said:
http://www.imnuts.org/downloads/charge/odin/charge.pit. He may also need this pit file that goes in the pit section of Odin. Good luck.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
I also am having issues with my droid charge being (was) soft bricked. Now it might be hard bricked. I installed the pit and is was successful, at least odin told me it was. However now my phone will not do anything. I cannot get the screen to so much as flash a glimmer of light. Hold up and plug into computer....nothing. Just try to power on...nothing. Try to go into cwm, nothing.
I am not sure what I did to start all my problems as I have flahsed ROMs with ODIN multiple times with no issue. Yesterday though it just did not take for some reason and not only that nothing would take. After failing to flash multiple ROMs that I have used many times before, I tried the "Packaged Rom that includes custom Kernel,ROM,CWM" mentioned here. http://forum.xda-developers.com/showthread.php?t=1160580 This worked, sort of.
This would get me into CWM but would be stuck on a boot loop back to CWM no matter what i tried. Custom .zip roms, stock .zip roms, etc.
SO thats when I tried the pit mentioned in this thread......now the phone is 100% unresponsive.
Can anyone please tell me if this can be recovered? And also can anyone tell me what I may have done wrong?

Categories

Resources