Database Info

[Q] HTC Inspire AT&T no carrier

I just flashed to LeeDroid V3.2.1 on my HTC Inspire. Upon install I have been unable to connect to the AT&T network to place any phone or data connections. I have attempted to change the radio/ril but have seen none of them take care of this issue, when I go through setup to select a carrier, I actually have no company to choose from. Hopefully you can assist me. Thanks in advance

stretch0r said:
I just flashed to LeeDroid V3.2.1 on my HTC Inspire. Upon install I have been unable to connect to the AT&T network to place any phone or data connections. I have attempted to change the radio/ril but have seen none of them take care of this issue, when I go through setup to select a carrier, I actually have no company to choose from. Hopefully you can assist me. Thanks in advance
Click to expand...
Click to collapse
I recently flashed to this rom as well with the same phone without issues. When you say "setup a carrier" i assume you are going to settings --> wireless and networks --> Mobile Networks --> Network Operators and then in here either going "search networks" or "select automatically"?
If this yields no results then I would recommend rolling back to prior rom and then attempting flash again.
If this doesn't work perhaps go back to stock then re-root and attempt flash again.
I know going back to stock can fix a lot of issues such as sound, reception, slow downloads that's why I recommend that option. Also, stock radio should work fine.
I hope this helps and good luck!
EDIT: Also look at the APN settings here is a link to it for your phone could be something there.

I also was going to suggest taking a look at the APN settings.

Sorted this issue out with a web due moment, I had the cover off and didn't realize it had a pair of contacts that were required to have the sim card seated. Sometimes It's the simplest answers.
Thanks for the help
Sent from my HTC Inspire using XDA app

no mobile data with new roms

Hi, I flashed cyanogenmod 7.2 the other night and everything went great, no problems. Today I wanted to try a couple different roms, I tried Buglees Beast and Codename Android 3.2, both flashed fine but I have no mobile data on either of them. If I restore back to Cyanogenmod everything works fine. Does anyone have any ideas why this may be? Thanks
Just reflashed bugless beast and still same thing, no mobile data. Then flashed cm 9.0 everythin great. I would still like to try the other roms if I can get them to work.

When u flash another ROM and u will have no data connection, go to; settings/more/mobile networks/access point name/ and check if there is access point name of the network u on, if not y need to make APN for ur network.

you have to input your specific carrier settings, check it by going to the carrier website, there should be a section where they list all the necessary settings for the internet to work. you can input it by going to settings->under wireless and networks, choose more->mobile networks->Access point names->menu button, and click on more. after inputting, make sure you enable it. hope this helps. if still doesn't work, try a new radio.

Billchen0014 said:
you have to input your specific carrier settings, check it by going to the carrier website, there should be a section where they list all the necessary settings for the internet to work. you can input it by going to settings->under wireless and networks, choose more->mobile networks->Access point names->menu button, and click on more. after inputting, make sure you enable it. hope this helps. if still doesn't work, try a new radio.
Click to expand...
Click to collapse
Thanks, that was the problem. There was already one in there, but it wasn't the right one,. Got the info from their website and it works great. Thanks again.

HTC Thunderbolt on PPC with 3g without using CDMAWS paid version

Ok everybody, after a few days of tinkering around with the help of many different forums and threads (sorry, i cant possibly start thanking individuals cuz i went through so many threads) i finally got my htc thunderbolt on PPC with 3g working. this is how
1.) remove the 4g sim card (if you have it) from the thunderbolt
2.) aquire all of the drivers you need for the thunderbolt and DM mode (hint, use htc sync)
3.) on the phones dialer dial ##3424# and press send
4.) hit the button that says reboot to modem+diag mode
5.) when your phone is plugged into the computer, has all the drivers installed, and is picked up in the device manager as 2 com ports
A.) The voice, text, and 1x com port is the htc diagnostic
B.) the 3g/4g com port is htc diagnostic 9k
6.) aquire a copy of cdmaws (2.7 is fine, there is a cracked version floating around, just use google no warez links
7.) open up cdmaws and connect to the non 9k port and connect
8.) go to the security tab and input your spc (000000) and click send, should say unlocked
9.) go to the other tab and under R-UIM Config make sure you select NV only then click write
9.) write all your nam settings, mdn, min, sid, nid, imsi and etc etc (other posts here at xda have all the details) repeat for name 2
10.) go to the other tab and under prl make sure it says universal and nam1
11.) click write and locate your pageplus evdo prl file (i used 51720) repeat for nam2
12.) go to the main tab and click disconnect but DO NOT CLOSE CDMAWS!!!!!!!
13.) connect the 9k port and repeat steps 8-12 but dont read, just write (all of your settings should still be on the screen)
14.) close cdmaws after all the settings are written to the phone
15.) find a copy of qpst 2.7 build 366 (again, google is your friend) and install it
16.) open up qpst configuration and click add new port
17.) find your non 9k com port click it once then click ok
18.) at the top go to start clients->service programming
19.) click ok then click read, click ok on the pop up that comes up
20.) go straight to the m.ip tab and create a new profile (or edit the one that shows up if it shows up) make it look like the screenshots i have below
21.) write the profile
22.) go to the PPP config tab and put *your 10 digit page plus phone number*@vzw3g.com for your nai and *your 10 digit phone number*@dun.vzw3g.com for teth. nai. password is vzw for um and an tab.
23.) close service programming and select the com port in configuration and remove it, close qpst configuration
24.) get a copy of dfs tools (demo is perfectly fine)
25.) see screenshots included at bottom of post
26.) make sure you start with the non 9k port, write what you need. and change ports to the 9k port without closing dfs tools, write everything to the 9k port (to be sure i pressed write for everything about 30 times but i may have been a bit excessive
27.) now activate the thunderbolt on your pageplus account by taking the last digit off of the imei number and they'll take it.
28.) insert ANY sim card into the sim card slot (NOT A VERIZON 4G ONE) i used a old nextel one to be honest
29.) turn on phone and dial *#*#4636#*#* and click phone information. change to cdma auto (prl) and close out.
30.) make a phone call and BAM 3g picks up and authenticates
Sorry if this guide isnt easy to follow, im not too good with wording things, lol. but it gives enough info for others to help including me.
also make sure under wireless and networks-> mobile networks-> that data roaming is allow for all trips, network mode is cdma only, and system select is automatic b
feel free to post to this thread with any shortcuts, questions, or comments

Screenshot with 3g
Sent from my thunderbolt on ppc with 3g

Speedtest
Sent from my thunderbolt on ppc with 3g

Thunderbolt 3g
Thanks for the hard work you have done deathrow1993 ,I have been around in circles with this, It looks like you have come up with the answer. I have 2 questions for you.. 1: I have CDMAWS 3.9 a little different from the one you have..You mention go to the other tab and under R-UIM Config make sure you select NV only. In CDMAWS 3.9 the R-UIM config is on the main tap and there is also the button that gives the option of CDMA or CDMA2 or EDVO etc. and another button that gives the option of NAM1 and NAM2 .. Do I write to NAM1 and NAM2 under CDMA and CDMA2 and EDVO?? The last question 2: on the program page of DFS CDMA you have 765 2385692 in several fields is this the phone # thanks for all your work with this. I have had the 1X working for a bit now but getting tired of the slow speeds. Again thanks to you everybody else that has contributed to this... Merry XMAS

ehsiii said:
Thanks for the hard work you have done deathrow1993 ,I have been around in circles with this, It looks like you have come up with the answer. I have 2 questions for you.. 1: I have CDMAWS 3.9 a little different from the one you have..You mention go to the other tab and under R-UIM Config make sure you select NV only. In CDMAWS 3.9 the R-UIM config is on the main tap and there is also the button that gives the option of CDMA or CDMA2 or EDVO etc. and another button that gives the option of NAM1 and NAM2 .. Do I write to NAM1 and NAM2 under CDMA and CDMA2 and EDVO?? The last question 2: on the program page of DFS CDMA you have 765 2385692 in several fields is this the phone # thanks for all your work with this. I have had the 1X working for a bit now but getting tired of the slow speeds. Again thanks to you everybody else that has contributed to this... Merry XMAS
Click to expand...
Click to collapse
Thats my cell phone number. Forgot to edit the pictures i guess. If you have cdmaws 3.9 and its the paid version in order to get 3g go to the evdo tab and put yourphone#@vzw3g.com for all fields and vzw as the password. Then have pageplus do a esn reset and a data reset and 3g should work. If its not the paid version then the evdo tab wont write. It sounds like you already have talk and text working? also make sure if you write something (nv only, nam settings, m.ip, and ppp settings, anything) make sure you write to both nam1 and nam2.

Thanks a bunch for your tutorial. I am going to try to flash my spare tbolt to PPC and have been reading everything that I could find.

ph19971207 said:
Thanks a bunch for your tutorial. I am going to try to flash my spare tbolt to PPC and have been reading everything that I could find.
Click to expand...
Click to collapse
no problem. just make sure youre on the stock rom so you can get diagnostic mode working. after everything is flashed i know its safe to flash a custom rom and even a new radio. i was on a bamf rom after 3g started working i then upgraded my radio from .9 to .19 and everything stuck. if you have any questions just keep me posted

deathrow1993 said:
no problem. just make sure youre on the stock rom so you can get diagnostic mode working. after everything is flashed i know its safe to flash a custom rom and even a new radio. i was on a bamf rom after 3g started working i then upgraded my radio from .9 to .19 and everything stuck. if you have any questions just keep me posted
Click to expand...
Click to collapse
Deathrow you can still get into diag mode with ICS roms and probably other non sense ones as well. Google "GScript Lite" and you can put your phone in diag mode without the reboot. I am with PPC too and love sense roms for ease of programming your phone without ever hooking it up to a computer but have run into losing data when flashing roms.

gimmeitorilltell said:
Deathrow you can still get into diag mode with ICS roms and probably other non sense ones as well. Google "GScript Lite" and you can put your phone in diag mode without the reboot. I am with PPC too and love sense roms for ease of programming your phone without ever hooking it up to a computer but have run into losing data when flashing roms.
Click to expand...
Click to collapse
thank you for this information. I've heard of this before but i've personally never used it or looked to far into it.

deathrow1993 said:
thank you for this information. I've heard of this before but i've personally never used it or looked to far into it.
Click to expand...
Click to collapse
You are welcome, it's actually pretty easy to use and you don't have to reboot your phone.

Hi deathrow1993,
Thank you very much for your brief and simple tutorial...finally my Thunderbolt get 3G here in Jakarta.

deathrow1993 said:
no problem. just make sure youre on the stock rom......any questions just keep me posted
Click to expand...
Click to collapse
Thanks again for your tips. I currently have voice and SMS working...Still trying to get data tho...

deathrow1993 if you ever make it near PDX I'm buying you a beer!
Process worked (took me awhile to find all the tools).
I haven't got a non-vzw-LTE SIM card yet so I have the Verizon one in there (wife's phone...keeps the phone from complaining) and it at least functions with text/voice for her.
I suspect it will start snagging 3G once I get the random SIM card in there.
Best part was that this avoided having to use the paid version of CDMA Workshop (their DEMO version you can download lets you mod only the CDMA pages, not the EVDO). I really didn't want to part with $99 just to program a used phone that isn't even mine
Thanks again! Learned a lot!

HTC Thunderbolt on Page Plus/w Voice/Text/MMS/Web
..Finally, after a week of trying to get data to work, IT WORKS!! HTC Thunderbolt on Page Plus 55$plan, Voice/Text/MMS/Web at 1xCDMA. I started with the tips from this thread and others alike, used cdmaws2.7, DFS4103, QPST366, and WirelessWorkshop dotcom. To be honest, it was the WirelessWorkshop remote software and the Technical help from them(Dwane was his name) that got this working. I could never get the com ports/diag driver's installed correctly. I thought they were but they weren't and WirelessWorkshop(Dwane the tech dude) connected to my pc through teamviewer and fixed my problem with the ports and drivers! Way more than I expected him to do since I only paid to use the software remotely. Before he fixed my pc I could only write to the htc diagnostic modem, not the 9K..So CHeers to him and the rest of y'all that have helped out...
Now I need to get 3G working. I did run across this from another site's thread but I don't know if it works to fix 3G cause there are no other references to it:
QUOTE
" page plus tb nam settings nam 1 and nam 2.
ppp user: [email protected]
ppp pass: 2618560F9EAC7232341CC4
M.ip profiles
nai: [email protected]
t nai: [email protected]
na: 918F5CFC5097AD0C3EB9064505C86572
aaa: 3466A134861121F7B96C03D8352F66EB "
I am not sure if changing the "vzw" pass to one of these would work or not.. Has anyone else seen this and does it work to connect 3G?

Hmm...
I popped in a non-4G-LTE SIM card yet still no 1x or 3G data (no MMS or anything).
Any words of insight here?

After having everything working(voice,sms,mms,data1x) for almost a week, I tried to get 3G to work and now I have no data or mms at all...I have tried to re-flash and re-flash, gone over all the settings a thousand times, but nothing...
Brandon314159, wish I could offer some advice but I find myself also asking for help now... The last three times I called PPC and had them reset my data, I still haven't gotten it back yet..

ph19971207 said:
After having everything working(voice,sms,mms,data1x) for almost a week, I tried to get 3G to work and now I have no data or mms at all...I have tried to re-flash and re-flash, gone over all the settings a thousand times, but nothing...
Brandon314159, wish I could offer some advice but I find myself also asking for help now... The last three times I called PPC and had them reset my data, I still haven't gotten it back yet..
Click to expand...
Click to collapse
I'm thinking the APN may be wrong on my Thunderbolt (still verizon?) because it wasn't a setting I had to change in this process?
I will have some more time here soon to look at it and see if I can figure it out..

I don't think the sim card really matters much but I'm using the verizon sim because it holds the PRL. 3G data is working for me, you need to be able to write your specific keys to the phone using DFS. This took me a while to figure out but eventually I got my hands on a droid incredible and was able to use it for my source to setup the thunderbolt. I am not sure if there is any other way to work around this or not but it worked for me.
Edit: It may be that you need to do all the programming as stated by the OP before you do the activation or have an ESN reset thru PPC.
Originall Posted by Brandon314159
Click to expand...
Click to collapse
I'm thinking the APN may be wrong on my Thunderbolt (still verizon?) because it wasn't a setting I had to change in this process?
I will have some more time here soon to look at it and see if I can figure it out..
Click to expand...
Click to collapse
EDIT: I was wrong about the sim card but if you have a new one that was NEVER programmed before, then it will work with the 4G LTE sim card.
I had 2 used & 1 new sim card but I could only get the NEW one to work correctly with 3G. Sorry if I lead anyone in the wrong direction.

I am only finding one port (9k) since I upgraded to ICS. Does anyone have a similar issue or could this be another problem?

trojanbrutha said:
I am only finding one port (9k) since I upgraded to ICS. Does anyone have a similar issue or could this be another problem?
Click to expand...
Click to collapse
I have found This rom here to be the most useful in setting things up to where you can reboot to diag mode and then set everything else up as stated in the OP. Once you are finished, flash the rom of your choice but don't go thru with the vzw activation process so all of your settings will stick. They may still stick, I don't know for certain as I have never allowed it to finish.

[Q] Lost data signal randomly, what can I do? (solved)

I was walking around school today, listening to slacker radio. Out of no where, the music stopped. I looked at my phone, and it said there was no signal. I didn't think much of it. I figured there was some sort of outage. When I got home and put my SIM in my old phone, I found it did indeed have a data signal. So I put my SIM back into my galaxy and again, no data. I can still make calls and send mms, but I can't connect to the internet, my email, the store etc. I have tried flashing between the stock ICS rom and CM9. I don't know what else to do. I was going to try flashing a different kernel, but would that even make a difference? Can someone help me?
Also, I did check the settings to make sure data was turned on and all that jazz.

same hir a couple week ago .i have my data connection.. and evry day i always flaahing and testing a new rom. and my data betwork.is still working.. but 1 week aho i lost my data connection.. i also try to flash stock rom.. and re activate my data network but still not working
Sent from my GT-S5360 using xda app-developers app

Well, I tried re-flashing the kernel, with no results. My next step is gonna be flashing a new modem unless someone else has a better idea.

thetouchablegod said:
Well, I tried re-flashing the kernel, with no results. My next step is gonna be flashing a new modem unless someone else has a better idea.
Click to expand...
Click to collapse
Try fixing permissions. Also are you sure TMOB didn't cut your data for some reason?

hechoen said:
Try fixing permissions. Also are you sure TMOB didn't cut your data for some reason?
Click to expand...
Click to collapse
I'm not on TMOB. I had to unlock my phone so I could get it on a local carrier. It worked fine for a day, then just quit.
Just tried fixing permissions; does not help.

thetouchablegod said:
I'm not on TMOB. I had to unlock my phone so I could get it on a local carrier. It worked fine for a day, then just quit.
Just tried fixing permissions; does not help.
Click to expand...
Click to collapse
Fixing permissions never hurts anything. It's good to at least once a week anyway. The next thing I would try is checking your APN to make sure it matches what your carriers settings are. Flashing another modem wouldn't hurt anything either but if the one you had was working fine I'd look at the APN setting first.

hechoen said:
Fixing permissions never hurts anything. It's good to at least once a week anyway. The next thing I would try is checking your APN to make sure it matches what your carriers settings are. Flashing another modem wouldn't hurt anything either but if the one you had was working fine I'd look at the APN setting first.
Click to expand...
Click to collapse
Lol, what is that, and where do I find it?

thetouchablegod said:
Lol, what is that, and where do I find it?
Click to expand...
Click to collapse
Stands for Access point name:
All Hail Wiki
You can find it under settings>wireless networks more>mobile networks>Access Point Names. You'll have to do a google search for your carriers correct APN settings. Just make sure they match if not hit left soft key. New APN and enter the correct info. Then left soft key again to save it. Then select it and reboot.

hechoen said:
Stands for Access point name:
You can find it under settings>wireless networks more>mobile networks>Access Point Names. You'll have to do a google search for your carriers correct APN settings. Just make sure they match if not hit left soft key. New APN and enter the correct info. Then left soft key again to save it. Then select it and reboot.
Click to expand...
Click to collapse
You sir are a genius. Thank you a ton. I called my carrier, and got the settings. My phone works great. Now to try new roms.

"Set preferred network type" defaulting to GSM only after a reboot

I recently tried to fix my GPS issues by trying out some previous OPO modem files, I ended up just reflashing the 33R one though as none helped. I now have a more annoying issue since doing this.
My network, Three UK uses LTE/WCDMA, so in the *#*#4636#*#* menu it is best to set "Set preferred network type:" to LTE/WCDMA, but after a reboot this changes to GSM every time, resulting in no signal at all.
I did some googling and found that some people had been able to edit their build.prop to change this default value, I changed the values as seen in the attached image. Unfortunately after a reboot it now only changes to WCDMA only and not LTE/WCDMA only. Does anyone know what changes I would have to make to make it change to LTE/WCDMA only?
Thanks.

If someone could upload their default build.prop that would also be useful.

oscarandjo said:
I recently tried to fix my GPS issues by trying out some previous OPO modem files, I ended up just reflashing the 33R one though as none helped. I now have a more annoying issue since doing this.
My network, Three UK uses LTE/WCDMA, so in the *#*#4636#*#* menu it is best to set "Set preferred network type:" to LTE/WCDMA, but after a reboot this changes to GSM every time, resulting in no signal at all.
I did some googling and found that some people had been able to edit their build.prop to change this default value, I changed the values as seen in the attached image. Unfortunately after a reboot it now only changes to WCDMA only and not LTE/WCDMA only. Does anyone know what changes I would have to make to make it change to LTE/WCDMA only?
Thanks.
Click to expand...
Click to collapse
Are you saying that you have no 2g signal/gsm signal on that phone? But you have 2g reception in your area , right?

maskelisuvari said:
Are you saying that you have no 2g signal/gsm signal on that phone? But you have 2g reception in your area , right?
Click to expand...
Click to collapse
Three has no 2G network at all, 3G/H+/LTE only. With it set to "GSM only" I have no signal at all.
I just need to set it to WCDMA/LTE and it works perfectly. The default config (after a reboot) that came with the phone works great too but it's changed to GSM only after flashing modems.
I've just flashed stock system.img, boot.img and modem using fastboot from the 33R fastboot zip but it's still not working as I'd like.

maskelisuvari said:
Are you saying that you have no 2g signal/gsm signal on that phone? But you have 2g reception in your area , right?
Click to expand...
Click to collapse
I'd appreciate it if you uploaded your build.prop

oscarandjo said:
Three has no 2G network at all, 3G/H+/LTE only. With it set to "GSM only" I have no signal at all.
I just need to set it to WCDMA/LTE and it works perfectly. The default config (after a reboot) that came with the phone works great too but it's changed to GSM only after flashing modems.
I've just flashed stock system.img, boot.img and modem using fastboot from the 33R fastboot zip but it's still not working as I'd like.
Click to expand...
Click to collapse
I got it , i am sorry i cant help you ,since i dont have 4g.Otherwise i can give you my build.prop to check.

maskelisuvari said:
I got it , i am sorry i cant help you ,since i dont have 4g.Otherwise i can give you my build.prop to check.
Click to expand...
Click to collapse
I don't think you need to. Just go to phone, press *#*#4636#*#*, press phone info and tell me whats in Set preferred network type, if it's what I think it is, upload your build.prop and I'll be very happy

oscarandjo said:
I don't think you need to. Just go to phone, press *#*#4636#*#*, press phone info and tell me whats in Set preferred network type, if it's what I think it is, upload your build.prop and I'll be very happy
Click to expand...
Click to collapse
That's a testing area, you shouldn't use it for setting parameters.
Anyway, try to go to setting --> mobile network setting and set the preferred network type there.

oscarandjo said:
I don't think you need to. Just go to phone, press *#*#4636#*#*, press phone info and tell me whats in Set preferred network type, if it's what I think it is, upload your build.prop and I'll be very happy
Click to expand...
Click to collapse
Its set to TD-SCDMA,GSM/WCDMA and LTE.Do you still want my buid.prop? I can give it to you , if you want.

maskelisuvari said:
Its set to TD-SCDMA,GSM/WCDMA and LTE.Do you still want my buid.prop? I can give it to you , if you want.
Click to expand...
Click to collapse
Yes that would be great.

Vonnegut said:
That's a testing area, you shouldn't use it for setting parameters.
Anyway, try to go to setting --> mobile network setting and set the preferred network type there.
Click to expand...
Click to collapse
I know that, but after rebooting the settings change to GSM only. I wanted to see what his was set to to see if his build.prop would be good for this. Build.prop seems to override that setting,

oscarandjo said:
I know that, but after rebooting the settings change to GSM only. I wanted to see what his was set to to see if his build.prop would be good for this. Build.prop seems to override that setting,
Click to expand...
Click to collapse
Ok, so the next question is..did you install the ColorOS beta ROM?

oscarandjo said:
I know that, but after rebooting the settings change to GSM only. I wanted to see what his was set to to see if his build.prop would be good for this. Build.prop seems to override that setting,
Click to expand...
Click to collapse
I had the same problem, after you change 4 or 5 times it finally is fixed

If I am correct, the OnePlus One is not CDMA compatible. If I am wrong on this, please correct me and I'll go pick one up for Verizon right now...
Sent from my iPod touch using Tapatalk

r3pwn said:
If I am correct, the OnePlus One is not CDMA compatible. If I am wrong on this, please correct me and I'll go pick one up for Verizon right now...
Sent from my iPod touch using Tapatalk
Click to expand...
Click to collapse
Sorry but no you are correct. If it worked for Verizon, then my life would be easier

this works but requires root, it works for dual sim as well, the settings will "stick" (save and apply) after a reboot. and PLEASE NOTE that of course you change the "3" to your preferred network
https://forum.xda-developers.com/galaxy-s4-sprint/general/how-to-fix-network-signal-gsm-sim-t3720534