Having a strange issue that I am not quite sure why is happening. I've been having a heck of a time attempting to access SD card with USB, as when I would connect it to my Windows Vista 64 Bit system the USB would constantly connect and disconnect, or my phone would simply never recognize that the USB was connected, or in more recent cases it simply goes into a boot loop or loads into the boot loader. On a hunch I decided to disable USB debugging and no more issues, except for I can't use adb obviously. I have been using my computer to customize my kindle fire, I wonder if that has something to do with it, perhaps the USB driver for adb is causing the issue? Has anyone else seen this issue? Solution? Thanks.
Update: I've come to the conclusion that there is a bad connection. I found that if I take the back cover off and connect the USB to the computer, it would work fine, but if I put any pressure on the battery it would disconnect and reconnect once the pressure was removed. I went ahead and sent out for a warranty replacement.
Related
Yes I know some will say install drivers or slide down the notifications.
But the problem is when I plug in, there isn't any notification for you to switch to disk drive mode.
Everything was working fine last week. There was no problems detecting my phone on my home and any PC at work. I have drivers install in my computer and can do adb commands
But now, when I plug in, it only shows the charging light.
I have done the following
On and off the USB debug option
Reboot phone
Try a 4 micro USB cable
Tried different USB slots on the computers
Use usbdeview and delete all HTC drivers and resinstall also not working
Remove my micro SD card and reinsert.
All doesn't work.
Strangely, one thing does. When I plug in the PC and I need to reboot, with my phone still plug in my PC. The notification will appear and I can do all things normally. But once I unplug and plug in again, same problem. Only can be solved with next reboot with phone plug in before hand. If windows is already loaded, it cannot be detected.
I though it was the rom. But I went to boot loader and same thing. It shows fastboot AC. If I do the reboot windows method, it will show fastboot USB .. will show fastboot AC if I replug in
I am starting to think my USB port on my phone is faulty.. any ideas?
Try plugging it and wait for a long time. Since I formated my computer it takes like 10-15min for my phone to show up after I plugged it. No idea what's causing it though.
Done that , charged it for 1hr plus, same
Best thing is try different cable, there is some issue with htc cable your pc sometime dont recognize phone, Other thing you can do it is keep ur phone connected to pc then boot your phone to Hboot or bootloader or fast boot, your pc will recognize your phone with generic driver.
jasminthoria said:
Best thing is try different cable, there is some issue with htc cable your pc sometime dont recognize phone, Other thing you can do it is keep ur phone connected to pc then boot your phone to Hboot or bootloader or fast boot, your pc will recognize your phone with generic driver.
Click to expand...
Click to collapse
hmm tried 4 cables.. same results..
Using the same cable, tried my mum's desireHD.. no problems detecting the USB each time..
Bootloader mode, it shows Fastboot AC
instead of Fastboot USB.. unless reboot my windows..
Oh i tired another micro SD card, same results.. :/
why mess with cables... AirDroid.
connect your phone to the pc via wifi.
direct link to the market: goo.gl/9YG73
but if you must connect via cable for something... have you checked the most obvious place? (sounds like you probably have but just in case...)
settings > connect to pc > default connection type
Mainspring said:
why mess with cables... AirDroid.
connect your phone to the pc via wifi.
direct link to the market: goo.gl/9YG73
but if you must connect via cable for something... have you checked the most obvious place? (sounds like you probably have but just in case...)
settings > connect to pc > default connection type
Click to expand...
Click to collapse
it cant even be detected, no notifications mate..
Flashed ROM......
Mine is doing the same thing. It didn't start until I flashed the new ROM. When in Windows, I just un-plug it, and re-plug it. Then it shows up immediately. But it always seems to show in flashboot.
UnixSlayer said:
Mine is doing the same thing. It didn't start until I flashed the new ROM. When in Windows, I just un-plug it, and re-plug it. Then it shows up immediately. But it always seems to show in flashboot.
Click to expand...
Click to collapse
hmm i even revert back to my original 1.35.707.1 RUU...
still not working.. i guess its time to claim warranty
try switching off firewall or/and antivirus i had same problem with eset 5 blocking phone so i put the stings to learning mode then plugged phone in and it created a new rule and shows up,then change setting back to what it was originally on
jonpickles70 said:
try switching off firewall or/and antivirus i had same problem with eset 5 blocking phone so i put the stings to learning mode then plugged phone in and it created a new rule and shows up,then change setting back to what it was originally on
Click to expand...
Click to collapse
and if that isn't working try it with HTC sync. which gives you the drivers of the device.
I got the same problem... any idea...
please help me..
Is there where USB cannot be recognized issue? If this is, I have a simple solution which took me forever to figure out.
I know this method sounds ridiculous, but give it a try. Unplug your charger connected to your computer/laptop and plug it in to a different outlet. Replug the USB with your phone connected, give it a sec, and it should work.
what operating system is your PC running? I was gonna say perhaps it might be a faulty USB port...
i have the same problem
What I do is go to devices and printers and then android phone then properties then hardware and disable the reenable the drivers. As soon as you reenable the drivers it should show up in disk mode. Hope this helps. This is the only phone I've had this problem with.
Recently we have been getting in stock i997's that are having USB issues connecting to the computer. As always we enable USB debugger and connect to the computer however now the units are going into charge mode a few seconds after connecting to the computer and shutting the device down. Once we disconnect the device from the computer it automatically restarts.
Here is what we have done so far with no luck:
-Enable USB debugging
-Disable USB debugging & enable mass storage
-*#7284# was set to USB=PDA, changed to Modem & back to PDA
-*#9090# Didn't see any relevant options
-Slightly bending the USB port
I don't think it is a hardware issue but a software issue that needs to be configured. Any help would be very much appreciated!!
USB
Get it as stock as you can with software. If the USB still does not connect correctly then it is a hardware issue. There was never a problem in any stock rom with USB connectivity.
Just my thoughts. It may not be the phone but the connection-- Computer, cable, oops,-- or drivers.
I'm facing the same problem !
I too have the same problem very weird tried several time stock have no issue in connection. this issue occur after few days not immediately and no regular pattern so can't say what's going on. right now my phone while put on charge shows charging but when un plug it still have 1% as charge no battery put to charge message shows up, tried with charger, usb to computer.
I also noticed before that charging stops and only come in effect when you pull the battery and plug the cable put the battery it will start the phone automatically and charge start up.
Can't ever put in charge in switch off mode as every time it automatically switch on my phone.
I tried several time these step 1. Go back to stock by heimdall , 2. heimdall kernal flash for red cwm, 3 wipe, format, fix permission 4. flash
couple of days work smoothly then problem reoccurs
Did you try mtp mode like with media player mode
Sent from my SGH-I997 using xda premium
RDomke said:
Get it as stock as you can with software. If the USB still does not connect correctly then it is a hardware issue. There was never a problem in any stock rom with USB connectivity.
Just my thoughts. It may not be the phone but the connection-- Computer, cable, oops,-- or drivers.
Click to expand...
Click to collapse
Thanks RDomke for the reply.
We already flashed UCKD5 with no luck. Would there be anything else we could do? I agree that it may be hardware if stock doesn't work but we have been getting in too many units out of box with this issue. Not saying that it isn't possible to be hardware, just seems like it's something that could be software related.
SOLVED
RDomke said:
Get it as stock as you can with software. If the USB still does not connect correctly then it is a hardware issue. There was never a problem in any stock rom with USB connectivity.
Just my thoughts. It may not be the phone but the connection-- Computer, cable, oops,-- or drivers.
Click to expand...
Click to collapse
RDomke,
Many thanks as we have solved the issue with your advise. The 1st unit we were testing did in fact have a bad usb port. Once properly diagnosed we tested another by flashing it back to stock and then performing a factory reset. Once done issue was solved and worked on many other with same issue.
i'm trying to connect my shield to my computer to do some basic android development (i have an app, it works on other devices, want to test it on the shield).
my problem is, when i plug it into the computer, nothing happens. to clarify, i don't mean that the drivers don't install correctly and then i can't do anything. what is happening is actually nothing. the computer (windows 8) does not recognize anything is happening, the device manager does not see any new devices even after scanning for hardware changes.
the shield is in development mode, and has usb debugging turned on, but i don't get any response anywhere. the shield does at least appear to charge over the usb cable, but that's it. listing adb devices also provides no output.
do you guys have any idea what might be going on that the device isn't recognized on any level that i can tell?
It sounds like either the USB port or the cable you're using is faulty.
Have you tried switching USB ports, to see if it's recognized then? And have you tried using a different cable?
joshuarivera said:
i'm trying to connect my shield to my computer to do some basic android development (i have an app, it works on other devices, want to test it on the shield).
my problem is, when i plug it into the computer, nothing happens. to clarify, i don't mean that the drivers don't install correctly and then i can't do anything. what is happening is actually nothing. the computer (windows 8) does not recognize anything is happening, the device manager does not see any new devices even after scanning for hardware changes.
the shield is in development mode, and has usb debugging turned on, but i don't get any response anywhere. the shield does at least appear to charge over the usb cable, but that's it. listing adb devices also provides no output.
do you guys have any idea what might be going on that the device isn't recognized on any level that i can tell?
Click to expand...
Click to collapse
If youre just trying to connect thru adb you need the universal naked driver. If the shield isnt being mounted try a different usb port and make sure youre using the shield cable as well. My samsung cable will charge it but i cant transfer data with it.
Did this get solved?
Did this ever get solved? I have the same issue. I have tried everything everywhere has said to do with no luck.
I think I've exhausted my options, hopefully somebody here has an idea.
From day 1, my TF300T has been unable to connect to a PC. At first I thought it was because one of my cats chewed on the USB cable before I could try (it still charged, just no PC connection) so I didn't do anything while it was still under warranty.
Since then, I've tried 3 different cables, multiple PCs and a Macbook, and I can't get anything out of it. It's not detected at all by the computer - no unknown device, no prompt for drivers, no device connected sound when I plug it in. No reaction on the tablet either, whether USB debugging is on or not. I also tried replacing the USB port on the tablet, but got the same thing. I doubt it's a driver issue since I'm not getting anything at all on either end of the connection.
It DOES connect to the dock ok, and all the dock functions seem to work. I've tried connecting the USB cable to both the tablet directly and the dock, and I get nothing from either port.
I'd really like to be able to flash custom ROMs on it, and I can't find a working way to root or flash it without a functioning USB connection. Could it be the third-party USB cables giving me problems, and if so, is there one that actually works? And if not, is this just a lost cause?
I've had my OPO for a little over 7 months now. My issue began when I had my desktop at a friend's house and plugged my phone into a USB 3.0 port to grab some videos off the phone when the phone suddenly shut off and would not turn back on. I thought it was bricked somehow but after leaving it plugged into a USB 2.0 port for some time, the charging screen came on and I was able to turn the phone on, but since then both OTG and MTP/PTP transfer doesn't work. If/when the phone is plugged into a computer, it gives an error and Device Manager shows
"Port_#0001.Hub_#0004 Unknown USB Device (Port Reset Failed)" and I'm not only able to charge the phone with one out the dozens of micro usb cables I have. I've tried several cables and a handful of different computers and OSs (Windows 7,8,8.1,10, Ubuntu 15.04, Kali Linux) all to the same result.
I'm running COS 12.1-YOG4PAS3JL, rooted, and have TWRP installed. The phone doesn't show up when in Fastboot mode or the bootloader either. Nothing changes when I disable or enable USB Debugging as well. With DriveDroid if I set the USB system to "Standard Android" the phone reboots and that seems like the closest I've been able to get to any kind of progress. I've gone through unbricking threads as well as Googled until my fingers bled but I'm yet to find anyone with a similar situation where the phone isn't bricked, the micro usb port isn't broken, I can't pick between MTP or PTP mode (USB Connection just says USB is now disconnected), and I'm not running a custom ROM. I tried replacing the micro usb on the phone so I now know that it wasn't that that's been messed up but I'm not sure where to go from here. Any suggestions or help is greatly appreciated.