Related
I tried to flash DlevROM INFUSE EDITION from ClockWorkMod and I get stuck in a boot loop.
I've downloaded a return to stock rom, transferred the zip to external sd but I can't seem to locate it on the "install zip from sdcard" screen.
What am I doing wrong? My phone is totally out of commission until I flash a new rom.
I've literally clicked on every folder in "install zip from sdcard" trying to figure out where the rom is.
When I click on "external_sd" it doesn't find any files. Am I looking in the wrong place?
Please help!!! My phone is totally out of commission! Thanks.
You have to wipe all of your data after flashing a new ROM. This is the most common cause of boot loops.
Also make sure you are useing the correct clock work mod version (infuse version). Useing a version made for another phone causes partition and file location mix ups.There is a 100% working one for the infuse somewhere on this fourm. I just can't find the link because I'm on mobile.
Sent from my Google Nexus S using XDA App
noahk11 said:
You have to wipe all of your data after flashing a new ROM. This is the most common cause of boot loops.
Also make sure you are useing the correct clock work mod version (infuse version). Useing a version made for another phone causes partition and file location mix ups.There is a 100% working one for the infuse somewhere on this fourm. I just can't find the link because I'm on mobile.
Sent from my Google Nexus S using XDA App
Click to expand...
Click to collapse
Thanks for the quick reply - however, since I'm in a boot loop, is it even possible to change the clockwork mod version?
Also, now when I go to "choose zip from sdcard" it says "no app2sd partition found." I can't click on it at all now.
delfinparis said:
Thanks for the quick reply - however, since I'm in a boot loop, is it even possible to change the clockwork mod version?
Also, now when I go to "choose zip from sdcard" it says "no app2sd partition found." I can't click on it at all now.
Click to expand...
Click to collapse
Still need help or did u resolve this?
drewneeb said:
Still need help or did u resolve this?
Click to expand...
Click to collapse
I totally need help - can't seem to do anything to fix. Any suggestions would be appreciated. Thanks in advance
Can you get into cwm at all?
Sent from my SAMSUNG-SGH-I997 using xda premium
ppalbicke said:
Can you get into cwm at all?
Sent from my SAMSUNG-SGH-I997 using xda premium
Click to expand...
Click to collapse
Yes, I'm in CWM right now.
try going into "mounts and storage" and "unmount /sdcard". its worked for me before
drewneeb said:
try going into "mounts and storage" and "unmount /sdcard". its worked for me before
Click to expand...
Click to collapse
It shows both as unmounted (sdcard and sd-ext) and it won't allow me to mount either. Here's the message when I try to mount sdcard.
can't mount /dev/block/mmcblk0p1 (or /dev/block//mmcblk0) (invalid argument) Error mounting SDCARD:!
delfinparis said:
It shows both as unmounted (sdcard and sd-ext) and it won't allow me to mount either. Here's the message when I try to mount sdcard.
can't mount /dev/block/mmcblk0p1 (or /dev/block//mmcblk0) (invalid argument) Error mounting SDCARD:!
Click to expand...
Click to collapse
i had sent u a pm but just ignore it..
go here
http://forum.xda-developers.com/showthread.php?t=1116251&highlight=gtg+ultimate+unbrink
download his unbrick file and follw direction exactly.
Instructions:
1.To begin, download the modified recovery from the link above and extract it anywhere on your computer to find a file named recovery.
2.That done, using a root explorer, mount your system partition as read/write.
3.Once the system partition is mounted, copy the recovery you extracted to /system/bin. Reboot your device into recovery.
4.Once in recovery select, Reinstall Packages
when youre done all that go ahead and boot phone up. download rom manager and hit the very first button. then tap galaxs i9000.
do as it says and use wifi to install package. plz its better to be safe then have to do all this again. then download dlev rom infuse edition and place in sdcard. then boot into recovery...
1: select "wipe data/factory reset"
2: select "wipe cache partition"
2: go to "advanced" and "wipe dalvick cache".
3: install .zip from sdcard
4:
---------- Post added at 08:24 AM ---------- Previous post was at 07:44 AM ----------
any progress?
drewneeb said:
try going into "mounts and storage" and "unmount /sdcard". its worked for me before
Click to expand...
Click to collapse
drewneeb said:
i had sent u a pm but just ignore it..
go here
http://forum.xda-developers.com/showthread.php?t=1116251&highlight=gtg+ultimate+unbrink
download his unbrick file and follw direction exactly.
Instructions:
1.To begin, download the modified recovery from the link above and extract it anywhere on your computer to find a file named recovery.
2.That done, using a root explorer, mount your system partition as read/write.
3.Once the system partition is mounted, copy the recovery you extracted to /system/bin. Reboot your device into recovery.
4.Once in recovery select, Reinstall Packages
when youre done all that go ahead and boot phone up. download rom manager and hit the very first button. then tap galaxs i9000.
do as it says and use wifi to install package. plz its better to be safe then have to do all this again. then download dlev rom infuse edition and place in sdcard. then boot into recovery...
1: select "wipe data/factory reset"
2: select "wipe cache partition"
2: go to "advanced" and "wipe dalvick cache".
3: install .zip from sdcard
4:
---------- Post added at 08:24 AM ---------- Previous post was at 07:44 AM ----------
any progress?
Click to expand...
Click to collapse
Sorry - just woke up.
Quick question - where is the file marked "recovery"? I only see in that download Odin and the three files that use with with Odin. Did you want me to follow his instructions first with Odin and then yours? Thanks.
Are you on the correct CWM version? It seems like the partition tables inside of CWM are messed up.
Also consider the ultimate unbrick software it's a one click thing that will send you back to stock.
Sent from my Google Nexus S using XDA App
Yes it is you just need to go into fastboot mode (volume up + power) and flash recovery from your computer again.
Sent from my Google Nexus S using XDA App
delfinparis said:
Sorry - just woke up.
Quick question - where is the file marked "recovery"? I only see in that download Odin and the three files that use with with Odin. Did you want me to follow his instructions first with Odin and then yours? Thanks.
Click to expand...
Click to collapse
ok... my bad i forgot a few steps...
follow all of gtgs unbick instructions then the rest.
here is a direct link to the recovery file... but since xda wont let me post outside links yet... :{ go to google and search "MODIFIED 3E RECOVERY INFUSE ADDICTIVE TIPS"
It should be first link.. open it.
go down to requirements and click on "Modified 3e Recovery" download and unzip that file
Voila u have the recovery file!!!!
Now follow instructions I have u after gtgs.
u will have to have a root explorer to complete "My instructions."
cm10 for sky a830 .......everything is working fine .....but if you find any bug notify me
Rom download address ::::::::-------
https://www.dropbox.com/sh/b5xdg3dgrwq7thh/jIrUxFS8Cc
for k and s version patches are in this link
hassantalal11 said:
cm10 for sky a830 .......everything is working fine .....but if you find any bug notify me
Rom download address ::::::::-------
https://www.dropbox.com/sh/b5xdg3dgrwq7thh/jIrUxFS8Cc
for k and s version patches are in this link
Click to expand...
Click to collapse
This just Hour Rom Final really?
did you flash it?
yes i have flashed it.and this rom is working like charm
uploading new rom.......wait for 1 hour
:fingers-crossed:
I know noobish question, but ive been trying for 2+ hours now without any luck..so can you tell me how to install this? these are the steps I currently follow
reboot phone to fastboot (phone is already rooted)
use fastboot to run CWM (6.0.3.1)
select wipe cache
select factory reset/wipe userdata
select mount and storage-> format sdcard/system partition
select advanced->wipe dalvic cache
select instal zip from sd card-> install from sd card-> select the downloaded zip file
zip file installs...
select go back
select reboot system now
and now when the phone restarts, I see a black screen that says
VEGA
the brightest star in the SKY
Pantech
and it just stays stuck there....
Note that I previously installed official 4.1.2 on my device....
thanks in advance.
death_relic0 said:
I know noobish question, but ive been trying for 2+ hours now without any luck..so can you tell me how to install this? these are the steps I currently follow
reboot phone to fastboot (phone is already rooted)
use fastboot to run CWM (6.0.3.1)
select wipe cache
select factory reset/wipe userdata
select mount and storage-> format sdcard/system partition
select advanced->wipe dalvic cache
select instal zip from sd card-> install from sd card-> select the downloaded zip file
zip file installs...
select go back
select reboot system now
and now when the phone restarts, I see a black screen that says
VEGA
the brightest star in the SKY
Pantech
and it just stays stuck there....
Note that I previously installed official 4.1.2 on my device....
thanks in advance.
Click to expand...
Click to collapse
you will need to install official icecream sandwich if want to install this rom...
link isn't working?
Zeuik said:
This just Hour Rom Final really?
did you flash it?
Click to expand...
Click to collapse
Please update link with latest update
I want rom for the sky vega a860 and the procedure also please tell me ????
Please i need your help about :
my phone is samsung galaxy i9003
my software now is jelly bean 4.1.2
I need to update my phoen to jb 4.2.2
can any one help me ??
i posted this thread in Q and A and no one help me
Please i need help
all i need to update my phone from android 4.1.2 to 4.2.2
please help me
Thanks ,,,
Hey bro follow this to make clean install (but this will wipe your data)
DO IT AT YOUR OWN RISK
1- make sure you have kies installed or just install galaxy sl usb drivers (thanks to Zulfauzi).
2-Download odin3 v1.85 from the attachments.
3-Download full DDLF2 from here (thanks to (thanks to sgatechwork).
4. Run Odin3 v1.85.
5. Check Re-Partition, Auto Reboot and F. Reset Time.
6. Click PIT button and select this file: latona_20110114.pit
7. Set it to download mode : Press Volume down + OK first, then hold Power button.
8. Connect USB cable and the program will detect the phone's Com number.
9. Click Start button to download the PIT file to phone.
10. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir].
11. Click PDA button and select this file: CODE_I9003DDLF2_CL1153545_REV08_user_low_ship.tar.md5.
12. Click PHONE button and select this file: MODEM_I9003DDLE1_REV_00_CL1149304.tar.md5.
13. Click BOOTLOADER button and select this file: APBOOT_I9003DDLF2_CL1153545_REV08_user_low_ship.tar.md5.
14. Click CSC button and select this file: GT-I9003-MULTI-CSC-ODDLF2_RST.tar.md5.
15: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!].
16. Click Start button to flash these files to phone.
17. Do not touch anything till you see PASS on the program window.
18. Factory reset.
19. [To fix issues that pertain] Reflash from steps 9 -15 again, No need of latona at this point.
thanks to Misledz for the instructions (original thread here)(I only edited file names).
Now download any Jb 4.2.2 rom and carefully follow the OP instructions.
I suggest CM10.1 A8 by dhiru1602 (thanks to him), rom is verry stable and smooth.
if I helped you please hit the "thanks" button
Best regards
ASMI1 said:
Hey bro follow this to make clean install (but this will wipe your data)
DO IT AT YOUR OWN RISK
1- make sure you have kies installed or just install galaxy sl usb drivers (thanks to Zulfauzi).
2-Download odin3 v1.85 from the attachments.
3-Download full DDLF2 from here (thanks to (thanks to sgatechwork).
4. Run Odin3 v1.85.
5. Check Re-Partition, Auto Reboot and F. Reset Time.
6. Click PIT button and select this file: latona_20110114.pit
7. Set it to download mode : Press Volume down + OK first, then hold Power button.
8. Connect USB cable and the program will detect the phone's Com number.
9. Click Start button to download the PIT file to phone.
10. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir].
11. Click PDA button and select this file: CODE_I9003DDLF2_CL1153545_REV08_user_low_ship.tar.md5.
12. Click PHONE button and select this file: MODEM_I9003DDLE1_REV_00_CL1149304.tar.md5.
13. Click BOOTLOADER button and select this file: APBOOT_I9003DDLF2_CL1153545_REV08_user_low_ship.tar.md5.
14. Click CSC button and select this file: GT-I9003-MULTI-CSC-ODDLF2_RST.tar.md5.
15: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!].
16. Click Start button to flash these files to phone.
17. Do not touch anything till you see PASS on the program window.
18. Factory reset.
19. [To fix issues that pertain] Reflash from steps 9 -15 again, No need of latona at this point.
thanks to Misledz for the instructions (original thread here)(I only edited file names).
Now download any Jb 4.2.2 rom and carefully follow the OP instructions.
I suggest CM10.1 A8 by dhiru1602 (thanks to him), rom is verry stable and smooth.
if I helped you please hit the "thanks" button
Best regards
Click to expand...
Click to collapse
Thanks for your reply
but there's another method about updating by CWM RECOVERY
do you know how this method done ?
dr_amjad said:
Thanks for your reply
but there's another method about updating by CWM RECOVERY
do you know how this method done ?
Click to expand...
Click to collapse
yes there is another way if you have recovery installed. Just tell us what ROM you are on (your 4.1.2 ROM name) and try to find out if you have CWM recovery(volume up+home+power). Let us know this this then we will proceed.
@ASMI1 :He is on a 4.1.2 OS means he have a custom ROM and re-partioning is not mandatory because he is comming for a CM10 base.
mustafahussain said:
yes there is another way if you have recovery installed. Just tell us what ROM you are on (your 4.1.2 ROM name) and try to find out if you have CWM recovery(volume up+home+power). Let us know this this then we will proceed.
@ASMI1 :He is on a 4.1.2 OS means he have a custom ROM and re-partioning is not mandatory because he is comming for a CM10 base.
Click to expand...
Click to collapse
Thank you very much mr mustafa
i download the ROM from video on youtube and this is link of video
http://www.youtube.com/watch?v=VqypSD3JBJk
It's CM 10 Alpha 3
And in the video there's a download link of the Rom and this is the link which in the video
http://forum.xda-developers.com/showthread.php?t=1868074
by the way : when i click power key there is an option called : Reboot
when i click on Reboot tell me that i can Reboot my phone and recovery and download mode
Thanks for your reply
If you like the jelly bean 4.1.2 (CM10) by Dhiru, surely you'll like the CM10.1 version.
It is in here. Review it for more details.
You will need the latest CM10.1 in Dhiru1602's downloads and this gapps..
Download both on the SD card. Then, basically this will be the instructions to install it:
Code:
Upgrading from previous versions of CM10
1. Reboot to Recovery.
2. Select the ROM zip from your SD Card and flash.
3. Flash Google Apps.
4. Reboot
PD: By the way, you can use the Reboot -> Reboot to recovery option you've mentioned.
Drizzt_Kueh said:
If you like the jelly bean 4.1.2 (CM10) by Dhiru, surely you'll like the CM10.1 version.
It is in here. Review it for more details.
You will need the latest CM10.1 in Dhiru1602's downloads and this gapps..
Download both on the SD card. Then, basically this will be the instructions to install it:
Code:
Upgrading from previous versions of CM10
1. Reboot to Recovery.
2. Select the ROM zip from your SD Card and flash.
3. Flash Google Apps.
4. Reboot
PD: By the way, you can use the Reboot -> Reboot to recovery option you've mentioned.
Click to expand...
Click to collapse
Thank you very much for your reply
i will try and tell you
but i will not do any thing about : Data wipe/Factory reset & 5. Format dbdata. , right ??
Drizzt_Kueh said:
If you like the jelly bean 4.1.2 (CM10) by Dhiru, surely you'll like the CM10.1 version.
It is in here. Review it for more details.
You will need the latest CM10.1 in Dhiru1602's downloads and this gapps..
Download both on the SD card. Then, basically this will be the instructions to install it:
Code:
Upgrading from previous versions of CM10
1. Reboot to Recovery.
2. Select the ROM zip from your SD Card and flash.
3. Flash Google Apps.
4. Reboot
PD: By the way, you can use the Reboot -> Reboot to recovery option you've mentioned.
Click to expand...
Click to collapse
I tried it
When i choose zip from sdcard and choose the rom tell me :
Installing : /sdcard/others/Cm10.1-Galaxy SL - JDQ39E-Alpha8.zip
Finding Update package ....
opening update package ....
E: Can't open / /sdcard/others/Cm10.1-Galaxy SL - JDQ39E-Alpha8.zip ( bad )
Installation aborted
What can i do ??
dr_amjad said:
I tried it
When i choose zip from sdcard and choose the rom tell me :
Installing : /sdcard/others/Cm10.1-Galaxy SL - JDQ39E-Alpha8.zip
Finding Update package ....
opening update package ....
E: Can't open / /sdcard/others/Cm10.1-Galaxy SL - JDQ39E-Alpha8.zip ( bad )
Installation aborted
What can i do ??
Click to expand...
Click to collapse
Redownload rom.
Sent from my GT-I9003 using xda premium
dr_amjad said:
I tried it
When i choose zip from sdcard and choose the rom tell me :
Installing : /sdcard/others/Cm10.1-Galaxy SL - JDQ39E-Alpha8.zip
Finding Update package ....
opening update package ....
E: Can't open / /sdcard/others/Cm10.1-Galaxy SL - JDQ39E-Alpha8.zip ( bad )
Installation aborted
What can i do ??
Click to expand...
Click to collapse
try to remove the rom zip from sdcard and copy it again from pc, this worked for me when I tried to install slim CM 7 by TheFrankenstain (here the thread if you wanted to try it..rom link here)(You rom is awesome TheFrankenstain...thank you)
If this didn't work then try to redownload the rom (don't use your phone to download roms...bad idea).
to make sure rom's archive is not corrupted, check you rom MD5 sum (Dev-Host server provide the correct MD5)
HashCheck is a good tool for this.
---------- Post added at 09:52 PM ---------- Previous post was at 09:29 PM ----------
dr_amjad said:
Thank you very much mr mustafa
i download the ROM from video on youtube and this is link of video
http://www.youtube.com/watch?v=VqypSD3JBJk
It's CM 10 Alpha 3
And in the video there's a download link of the Rom and this is the link which in the video
http://forum.xda-developers.com/showthread.php?t=1868074
by the way : when i click power key there is an option called : Reboot
when i click on Reboot tell me that i can Reboot my phone and recovery and download mode
Thanks for your reply
Click to expand...
Click to collapse
BE CAREFUL...You can only update to CM10.1 rom (or any other rom based on CM10.1) only if you have CM10 Alpha4 rom (or any other rom based on CM10 Alpha4)
But in your case (you have CM10 A3), you have to follow the whole guide mentioned in the second post.
This is what LoLaTiOn said:
How to install
Warning only for lasted base CM10 Alpha4
if older base CM10 Alpha3 Full KPE please !!!
- Wip Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
Flash first clean for mandatory starting
On CM10 Alpha 3 and all other basic Froyo, Gingerbread, ICS, JB
Click to expand...
Click to collapse
................
thread here.
If you are worried about your data make full backup using recovery and you can restore your apps or your full rom at any time...clean Install is always recommended over updating from previous versions.
BTW...I think full Nandroid restore is dangerous due to different partitioning in ICS/JB roms so it's recommended always to reparation using odin and install full firmware again.
Also, any custom rom is rooted and deodexed and has CWM recovery pre-installed.
sorry for my bad english
ASMI1 said:
try to remove the rom zip from sdcard and copy it again from pc, this worked for me when I tried to install slim CM 7 by TheFrankenstain (here the thread if you wanted to try it..rom link here)(You rom is awesome TheFrankenstain...thank you)
If this didn't work then try to redownload the rom (don't use your phone to download roms...bad idea).
to make sure rom's archive is not corrupted, check you rom MD5 sum (Dev-Host server provide the correct MD5)
HashCheck is a good tool for this.
---------- Post added at 09:52 PM ---------- Previous post was at 09:29 PM ----------
BE CAREFUL...You can only update to CM10.1 rom (or any other rom based on CM10.1) only if you have CM10 Alpha4 rom (or any other rom based on CM10 Alpha4)
But in your case (you have CM10 A3), you have to follow the whole guide mentioned in the second post.
This is what LoLaTiOn said:
................
thread here.
If you are worried about your data make full backup using recovery and you can restore your apps or your full rom at any time...clean Install is always recommended over updating from previous versions.
BTW...I think full Nandroid restore is dangerous due to different partitioning in ICS/JB roms so it's recommended always to reparation using odin and install full firmware again.
Also, any custom rom is rooted and deodexed and has CWM recovery pre-installed.
sorry for my bad english
Click to expand...
Click to collapse
Thank you very much mr ASMI 1 for your reply
but sorry i am still Noob in android development and updating
but according to your reply i must do :
- Wip Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
Right ??
and please is there a video about my case (( updating samsung gt i 9003 from cm 10 alpha 3 to cm 10.1 alpha 8 )) ??
and sorry for annoyance you
ASMI1 said:
try to remove the rom zip from sdcard and copy it again from pc, this worked for me when I tried to install slim CM 7 by TheFrankenstain (here the thread if you wanted to try it..rom link here)(You rom is awesome TheFrankenstain...thank you)
If this didn't work then try to redownload the rom (don't use your phone to download roms...bad idea).
to make sure rom's archive is not corrupted, check you rom MD5 sum (Dev-Host server provide the correct MD5)
HashCheck is a good tool for this.
---------- Post added at 09:52 PM ---------- Previous post was at 09:29 PM ----------
BE CAREFUL...You can only update to CM10.1 rom (or any other rom based on CM10.1) only if you have CM10 Alpha4 rom (or any other rom based on CM10 Alpha4)
But in your case (you have CM10 A3), you have to follow the whole guide mentioned in the second post.
This is what LoLaTiOn said:
................
thread here.
If you are worried about your data make full backup using recovery and you can restore your apps or your full rom at any time...clean Install is always recommended over updating from previous versions.
BTW...I think full Nandroid restore is dangerous due to different partitioning in ICS/JB roms so it's recommended always to reparation using odin and install full firmware again.
Also, any custom rom is rooted and deodexed and has CWM recovery pre-installed.
sorry for my bad english
Click to expand...
Click to collapse
(( if older base CM10 Alpha3 Full KPE please !!! ))
what the meaning of KPE ??
and i must do this ?? (( if older base CM10 Alpha3 Full KPE please !!! ))
dr_amjad said:
(( if older base CM10 Alpha3 Full KPE please !!! ))
what the meaning of KPE ??
and i must do this ?? (( if older base CM10 Alpha3 Full KPE please !!! ))
Click to expand...
Click to collapse
it means that if you have a base older to CM10 Alpha 3 then you should proceed with full KPE,,,
so IF YOUR CURRENT ROM IS ON CM10 Alpha 3 I would suggest just flash CM10 Alpha4 base ROM by Dhiru then,
-Wipe Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
mustafahussain said:
it means that if you have a base older to CM10 Alpha 3 then you should proceed with full KPE,,,
so IF YOUR CURRENT ROM IS ON CM10 Alpha 3 I would suggest just flash CM10 Alpha4 base ROM by Dhiru then,
-Wipe Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
Click to expand...
Click to collapse
Now i have Cm 10 alpha 3
you want me to do these steps :
-Wipe Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
and update my phone to Cm 10alpha 4 or cm 10.1 alpha 8 ?????????
dr_amjad said:
Now i have Cm 10 alpha 3
you want me to do these steps :
-Wipe Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
and update my phone to Cm 10alpha 4 or cm 10.1 alpha 8 ?????????
Click to expand...
Click to collapse
No, to upgrade from previous version of CM10 follow this:
1. Reboot to Recovery.
2. Select the ROM zip from your SD Card and flash.
3. Flash Google Apps.
4. Reboot
Click to expand...
Click to collapse
and then
-Wipe Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
here where to download CM10 A4 and google apps(20121011 for CyanogenMod 10.0.x) (thanks to master dhiru1602).
BTW, in the past we used to install XXKPE stock rom (pit, bootloader, PDA, Phone, and CSC)(this is what meant by full KPE) and then install DDLF2 as PDA in download mod. But now full DDLF2 is out so we don't need XXKPE anymore to make clean install, you just install full DDLF2 (pit, bootloader, PDA, Phone, and CSC) the same way you install XXKPE and then proceed with installing your custom rom.
it is recommended to make clean install always before installing any custom rom (CM or rom based on CM) to prevent any issue (installing custom rom over another custom rom may cause some problems like lags and no signal issue...etc) just make clean install.
I advise you to upgrade only if, for example; you want to update to REMICS rom and you have previous version of REMICS rom or you want to update to carbon rom and you have previous version of carbon rom or you want to update to CM10.1 A8 rom and you have previous version of CM10.1 A7 rom...Do you get my point?
Hello every body
I have a problem during installing a new ROM
i have samsung galaxy SL i9003 and i this phone was in CM 10.1 alpha 8
I tried to upgrade my phone to CM10.2 Rom
and this is the link of the ROM : http://forum.xda-developers.com/showthread.php?t=2431402
first i return to DDLF2 then go to recovery mode
i do wipe data / factory rest
After that when i select the Rom zip folder from Sdcard to install
the phone tell me :
Finding update package...
Opening update package...
Installing update...
assert failed: getprop("ro.product.device") == "captivate" ||
getprop.("ro.build.product") || ... (and so on)
E:Error in /sdcard/#whateverpackage#.zip
Status 7
Installation aborted.
there is any help ??
don't format system after flashing ddlf2. directly install 10.2 over it.
procedure =
1) flash ddlf2
2) root it
3) go to recovery and directly install 10.2.
4) wipe data/reset. (optional)
(don't format anything or else it will give you that error)
hope this helps you.
maxs8007 said:
don't format system after flashing ddlf2. directly install 10.2 over it.
procedure =
1) flash ddlf2
2) root it
3) go to recovery and directly install 10.2.
4) wipe data/reset. (optional)
(don't format anything or else it will give you that error)
hope this helps you.
Click to expand...
Click to collapse
Thank you very much
i will try and tell you
but in the link of The ROM the installation instruction is :
1. Flash CWM Compatible Kernel (CF ROOT)
2. Reboot to Recovery.
3. Wipe Data / Factory Reset.
4. Select the ROM zip from your SD Card and flash.
5. The device will reboot and finish flashing.
6. Reboot to Recovery Again.
7. Flash Google Apps.
8. Reboot
so wipe data/factory rest is before installing the ROM zip and that what i did
flash cf root for ddlf2 first. and you posted on the wrong section.
Sent from my Nexus 4 using xda app-developers app
format system and sdcard bro !!!
dr_amjad said:
Hello every body
I have a problem during installing a new ROM
i have samsung galaxy SL i9003 and i this phone was in CM 10.1 alpha 8
I tried to upgrade my phone to CM10.2 Rom
and this is the link of the ROM : http://forum.xda-developers.com/showthread.php?t=2431402
first i return to DDLF2 then go to recovery mode
i do wipe data / factory rest
After that when i select the Rom zip folder from Sdcard to install
the phone tell me :
Finding update package...
Opening update package...
Installing update...
assert failed: getprop("ro.product.device") == "captivate" ||
getprop.("ro.build.product") || ... (and so on)
E:Error in /sdcard/#whateverpackage#.zip
Status 7
Installation aborted.
there is any help ??
Click to expand...
Click to collapse
Ok,i just encountered this problem just right now ,with clean install ,so after i clicked wipe data /factory reset , i clicked instal zip from rom ,chosed rom ,after this phone restarted and entered again in CWM ,when i chosed again install zip from sd etc... encountered this error ,so i go back in main menu and chose wipe data /factory reset again ,and after this it worked like a charm to install the rom ,no error was displayed. I hope it will work for you to !
LoLaTiOn said:
format system and sdcard bro !!!
Click to expand...
Click to collapse
formatting the system will remove the baseband which wont allow 10.2 to install. i'd encountered the same problem 2 days back and i'd solved the way I mentioned above.. to cross check the error again (2nd time) I formatted the system after clean flash of ddlf2 and I got the same error.. just installing 10.2 directly over ddlf2 won't cause any problem.
---------- Post added at 09:11 AM ---------- Previous post was at 09:05 AM ----------
dr_amjad said:
Thank you very much
i will try and tell you
but in the link of The ROM the installation instruction is :
1. Flash CWM Compatible Kernel (CF ROOT)
2. Reboot to Recovery.
3. Wipe Data / Factory Reset.
4. Select the ROM zip from your SD Card and flash.
5. The device will reboot and finish flashing.
6. Reboot to Recovery Again.
7. Flash Google Apps.
8. Reboot
so wipe data/factory rest is before installing the ROM zip and that what i did
Click to expand...
Click to collapse
"wiping date/factory reset " won't cause any problem. just don't format any thing.. if you want you can format SD Card for your satisfaction.. but don't format system or else that will lead to that error.
hey bro flash only cf-root or bam kernel and don't format system if the installation failed you will have to flash DDLF2 again.
THE SAME ERROR occur again ~~!!
I tried more that 10 times to return to DDLF2 then upgrade my phone to cm10.2 dhirru Rom 4.3 android and the same error appear in every time !!
ASSERT FAILED status 7
Now moment i returned to DDLF2 and upgrade my phone to cm10.2 alpha 8 dhirru ROM and it success upgrading
It's the only Rom which flashing occur Successfully
So , there is NO HELP ?!
Asset failed. Mean either wrong rom or wrong phone.
I saw your error show "captivate". Are you sure you in the right forum..? Btw. Here is galaxy sl gt-i9003 and 9003L
Sent from my Galaxy Nexus using Tapatalk 4
i had the same error while installing cm10.2 it gave me the same error(status 7).device only would go in recovery mode.after that i downloaded the rom again and it worked.the download was corrupt.so download again and try. :fingers-crossed:
@chongns : I am sure that it's a right Rom and Right phone ~~ !
dr_amjad said:
@chongns : I am sure that it's a right Rom and Right phone ~~ !
Click to expand...
Click to collapse
you try bypass the assert check by delete those line in rom zip file, the file is updater-script in folder
"CM10.1-GalaxySL-JDQ39E-Alpha7/META-INF/com/google/android"
Code:
assert(getprop("ro.product.device") == "galaxysl" || getprop("ro.build.product") == "galaxysl" ||
getprop("ro.product.device") == "GT-I9003" || getprop("ro.build.product") == "GT-I9003" ||
getprop("ro.product.device") == "GT-I9003L" || getprop("ro.build.product") == "GT-I9003L");
open up the zip without unzip it, just open with winrar than edit than save.
this is a try, never try it before for our phone.
---------- Post added at 08:20 PM ---------- Previous post was at 08:15 PM ----------
dr_amjad said:
@chongns : I am sure that it's a right Rom and Right phone ~~ !
Click to expand...
Click to collapse
just found out the ROM download site having 2 type of CM10.2, one is for LG Optimus black others one for GT-i9003
makesure you download the correct one
@chongns : Thanks very much for help
Every thing now i being OK
I download the Rom Again and download gapps
Then i tried to flash the rom and tell me the same error ( status 7 )
then i do Wipe Data / Factory Reset one time and repeat it again
Then i choose the ROM zip and it flashed OK
all what i do that i did Wipe Data / Factory Reset twice followed by each other
Thanks very much for helping me
dr_amjad said:
@chongns : Thanks very much for help
Every thing now i being OK
I download the Rom Again and download gapps
Then i tried to flash the rom and tell me the same error ( status 7 )
then i do Wipe Data / Factory Reset one time and repeat it again
Then i choose the ROM zip and it flashed OK
all what i do that i did Wipe Data / Factory Reset twice followed by each other
Thanks very much for helping me
Click to expand...
Click to collapse
although, you have flash through, but that still weird to have error status 7.
btw, the correct step should be factory reset than flash the zip, yous is flash the zip than factory reset.......
chongns said:
although, you have flash through, but that still weird to have error status 7.
btw, the correct step should be factory reset than flash the zip, yous is flash the zip than factory reset.......
Click to expand...
Click to collapse
yes
i did first Wipe Data / Factory Reset two times each one follow the other then i flashed the Rom zip
Working method (tried several times with different roms):
-flash DDLF2
-flash cfroot
-recovery mode (the green one)
-flash your rom, then you'll be bringed to the new version of cwm (the blue one)
-wipe data/factory reset
-format system
-flash the rom
Hi all:
I'm also getting this issue lately, and I use to solve it going to mounts and storage and mounting all the filesystems, then try again.
Looks like the updater script can't mount the file systems automatically or something lately and so it gives that error.
Hope this solves your issue.
BTW, I also saw it extrange that the assert of the zip you were flashing indicated captivate, our device codename for CyanogenMod is galaxysl, not captivate, make sure you're flashing the right zip. (Also, captivate is not p970 either, so you should have mistakenly downloaded the zip from somewhere else).
Sent from my GT-I9003 using xda premium
Simply copy the file to internal SD card and flash it. Problem solved for me.
Sent from my GT-I9003 using xda app-developers app
sam_777 said:
Simply copy the file to internal SD card and flash it. Problem solved for me.
Sent from my GT-I9003 using xda app-developers app
Click to expand...
Click to collapse
Here's the solution to this problem
Q&A for [ROM] Flying Sparrow V3.0 { The Fastest ROM For Micromax a89 }
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer.
Before posting, please use the forum search and read through the discussion thread for [ROM] Flying Sparrow V3.0 { The Fastest ROM For Micromax a89 }. If you can't find an answer, post it here, being sure to give as much information as possible (firmware version, steps to reproduce, logcat if available) so that you can get help.
Thanks for understanding and for helping to keep XDA neat and tidy!
not working..after imstalling it reboot to recovery
not working..after imstalling it reboot to recovery..help
Follow the instructions carefully
sunilbagal said:
not working..after imstalling it reboot to recovery..help
Click to expand...
Click to collapse
1) Download the zip file from the download link provided below...
2) Extract the zip file....
3) You will find two zip files inside it,, first one is ROM zip and another is addons zip...
4) Copy both the zip files two your SDcard ..
5) Go to recovery mod and firstly take the nandroid backup and reboot...
6) Again go to recovery mod and wipe cache ,data ,system and dalvik cache flash the ROM zip only and reboot...
7) Then again go to recovery mod and flash the addon zip...
8) That's it ..now reboot your phone ....now fly with sparrow
---------- Post added at 06:28 AM ---------- Previous post was at 06:25 AM ----------
sunilbagal said:
not working..after imstalling it reboot to recovery..help
Click to expand...
Click to collapse
Do not flash the addon zip just after installing ROM .... A reboot is necessory after installing ROM and after a reboot then flash addon zip.. Also don't do any factory reset after installing both rom and addon zip.
And after this if again any problem occur then do inform me...
a complaint
My handset has been appearing white and then booting often, but it is not booting properly and it becoming white and then again booting as ninja..I don't know what to do...please help me Bro's....I can't use my headset ninja a89..;reply me soon... XDAXda
Finally sorry for my English...
I think you don't followed the instructions to install flying sparrow carefully... Please read the instructions first and strictly follow them.. And also use the cautions..
Also report me if it work
USB Mass storage not working
Hi
I have installed Flying Sparrow OS in my A89. But my USB mass storage function is not working. I cannot connect it as a media device or as a camera. It just gets charging when connected to my computer. How can I get out of this??? Thanks in advance..
solution
Karthik Bala said:
Hi
I have installed Flying Sparrow OS in my A89. But my USB mass storage function is not working. I cannot connect it as a media device or as a camera. It just gets charging when connected to my computer. How can I get out of this??? Thanks in advance..
Click to expand...
Click to collapse
Actually flying sparrow is completely bugless but if you are facing problem of usb ,do the following things for solution. Firstly install the rom zip only don't flash the addon zip and reboot .Then try to connect your phone to your computer. Then usb will work.. And after this try ,go to recovery mode and flash the addon zip.. And reboot. Don't do factory reset.. Now usb will work.. If any other problem occurs report me
Not Working in my A89
HI,
I downloaded your file, and transferred to SD card, I used CWM Recovery to install, after few steps , after opening update package...., installing update......, installation aborted. I tried the same 3 times and getting the same message. Kindly guide me to install your ROM in micromax A89.
venki
+91 9342519832
solution
vsmv said:
HI,
I downloaded your file, and transferred to SD card, I used CWM Recovery to install, after few steps , after opening update package...., installing update......, installation aborted. I tried the same 3 times and getting the same message. Kindly guide me to install your ROM in micromax A89.
venki
+91 9342519832
Click to expand...
Click to collapse
Installation is abroted because you are installing the wrong zip file...
You need to firstly extract the downloaded zip file and you will find the ROM zip inside it
Kindly follow the steps...
1) Download the zip file
2) Extract the zip file....
3) You will find two zip files inside it,, first one is ROM zip and another is addons zip...
4) Copy both the zip files two your SDcard ..
6) Go to recovery mod and wipe cache ,data ,system and dalvik cache flash the ROM zip only and reboot...
7) Then again go to recovery mod and flash the addon zip...
8) That's it ..now reboot your phone
Need Help
installation Steps For CWM 6 Users
Make Backup BEFORE Flashing
1.Download Flying sparrow v3.0
2.Put it on your SDcard
3:Go to CWM Recovery(Press Vol. Up Power
Button)
4.wipe cache partition
5. Format Data(Mounts And Storage>Scroll
Down>Format Data)
6. Format System(Mounts And Storage>Scroll
Down>Format System)
7. Format Dalvik Cache(Advanced>Dalvik
Cache)
8. Go back at the first page of the CWM
recovery and choose install .zip from SDcard
9.Choose
Flying sparrow v3.0.zip
10.then reboot and then again go to recovery and then go to again install zip from sd card and choose addon zip and flash it
11. then reboot and then again go to recovery and then go to again install zip from sd card and choose full kitkat white theme and flash it
12.Then reboot system now
I am using this method for install flying sparrow v3.0 in Micromax a89 ninja this method is right or not please tell me flying sparrow v3.0 developers fast
Abhay S said:
installation Steps For CWM 6 Users
Make Backup BEFORE Flashing
1.Download Flying sparrow v3.0
2.Put it on your SDcard
3:Go to CWM Recovery(Press Vol. Up Power
Button)
4.wipe cache partition
5. Format Data(Mounts And Storage>Scroll
Down>Format Data)
6. Format System(Mounts And Storage>Scroll
Down>Format System)
7. Format Dalvik Cache(Advanced>Dalvik
Cache)
8. Go back at the first page of the CWM
recovery and choose install .zip from SDcard
9.Choose
Flying sparrow v3.0.zip
10.then reboot and then again go to recovery and then go to again install zip from sd card and choose addon zip and flash it
11. then reboot and then again go to recovery and then go to again install zip from sd card and choose full kitkat white theme and flash it
12.Then reboot system now
I am using this method for install flying sparrow v3.0 in Micromax a89 ninja this method is right or not please tell me flying sparrow v3.0 developers fast
Click to expand...
Click to collapse
Everything is ok but between steps 1 and 2 you forget to extract zip file... After extraction you will find rom zip and addon zip.. You have to put these two zip files in your sdcard...
install fly sparrow in micromax a89 ninja
installation Steps For CWM 6 Users
Make Backup BEFORE Flashing
1.Download Flying sparrow v3.0
2.Put it on your SDcard
3:Go to CWM Recovery(Press Vol. Up Power
Button)
4.wipe cache partition
5. Format Data(Mounts And Storage>Scroll
Down>Format Data)
6. Format System(Mounts And Storage>Scroll
Down>Format System)
7. Format Dalvik Cache(Advanced>Dalvik
Cache)
8. Go back at the first page of the CWM
recovery and choose install .zip from SDcard
9.Choose
Flying sparrow v3.0.zip
10.then reboot and then again go to recovery and then go to again install zip from sd card and choose addon zip and flash it
11. then reboot and then again go to recovery and then go to again install zip from sd card and choose full kitkat white theme and flash it
12.Then reboot system now
I am using this method for install flying sparrow v3.0 in Micromax a89 ninja this method is right or not please tell me flying sparrow v3.0 developers fast
Installation steps updated
Steps for installing rom properly are updated now and explained properly for cwm and twrp users individually in the discussion page.....:d
regarding xblast tools
Flying sparrow is the best rom i have used till now. the only thing that i want to ask is how to change the background image of apps like settings, contacts,phone.
Secondly,certain changes made in xblast tools like of quick settings do not get implemented.how do i do that?
And finally, everytime i open Ex themer & select the theme option it says no data found. How do i theme my phone.
I use a micromax a89 ninja.
Thank you
Solution
Pbm12345 said:
Flying sparrow is the best rom i have used till now. the only thing that i want to ask is how to change the background image of apps like settings, contacts,phone.
Secondly,certain changes made in xblast tools like of quick settings do not get implemented.how do i do that?
And finally, everytime i open Ex themer & select the theme option it says no data found. How do i theme my phone.
I use a micromax a89 ninja.
Thank you
Click to expand...
Click to collapse
For changing the background wallpapers of apps you need to decompile them.. There are many tutorials available on xda ,kindly follow them..
Quick settings will not work work on flying sparrow as quick setting will only work for jb.. You can try to install them but i know that this feature will not work for an ics based rom.. Proceed to post no.2 in the discussion thread of flying sparrow for installing xposed framework.. Also i have provided the list features of xblast tools which are tested and work perfectly on flying sparrow.. If follow the procedure in post 2 correctly you will successfully work with exthemer... You need to select exthemer in the module list of xposed installer.. And reboot.. I hope this will help you and give answers to you your questions... Also participate in poll in flying sparrow thread...
Error
Hey,there is problm after reboot......
it does not go further after boot animation..
plz help me out....
How to remove transparency in each view
Hi Preet,
I have installed your ROM, on MMX A89 just few minutes before, and it looks nice.
I have some questions and main is I DO NOT want Transparent background in any case.
How do I achieve that in your ROM? I do not like transparent background.
Please help me for this.
Note: I will wait for 1 day otherwise I will restore my old backup (ICS 4.0.4 company look). And what you had said about battery saver? What bug it has for battery?
Thanks in advance.