I paid a non-corporate MetroPCS store to flash 4 Sprint CDMA Hero's to MetroPCS and add the ESN's into the system, I walked out with 4 working phones.
After having the phones for a while, I was playing around with one of them as I was learning how to install ROM's and such and in the process the phone somehow got set back to its like new state.. as in original phone number, all Metro info was gone, including MMS and Internet. If I tried to place a call I got the standard Sprint "your account can not be validated" recording.
After playing around for a couple of days I can place a call to 611 (Metro CS) and it recognizes my phone and my account, however that's the only number I can call. If I try to call a regular number I get a strange recording asking me if I want to place a collect call.
I know in order to get my phone working I need the following information:
SID/NID pair I have the correct information entered into the phone
MDN/MIN pair <------ I suspect this is where my problem is.
I called Metro to get my MIN, its not the same as my phone number and its not the original phone number. I cannot figure out the correct place to enter this information.
I have tried in CDMA workshop, QPST tools and DFS CDMA tools. These programs can be very confusing with MIN's and True MIN's, the list goes on.
I have flashed my phone to and old stock Sprint 2.1 ROM (NFX) so that I could enter the programming codes and such. Link to the ROM
http://forum.xda-developers.com/showthread.php?t=849024
I am only concerned with getting voice working for now, I might be able to do the rest on my own.
Any help is greatly appreciated.
Thanks.
Edited to add that I do have a MetroPCS prl file installed.
Edit 2 to add that this cant be done. When the phone was originally flashed the guy didnt use my phones MEID for whatever reason.. therefore the phone is not in the MetroPCS system. I tried to get the info from MetroPCS but no dice.
I will not go back to the same place to get it fixed.
Related
Hi. I've found this site to be very helpful in my attempts to activate an Alltel HTC Hero cdma on the Page Plus network.
I finally got the phone to make calls, but it says that I'm roaming - there's a triangle above the signal strength meter. I checked it by making a call and it charges me the roaming rate of $0.29 a minute. I think I need an updated .prl file, but I'm not sure.
I'm able to send and receive text. I cannot send or receive MMS or connect to the internet.
Maybe someone here can help me. Please
Phone will be used in Berlin, WI 54923 (Near the following cities: Appleton, Oshkosh, Neenah, Fond du Lac)
Original phone details:
Alltel network, but Alltel is no longer in my area. Alltel customers were sent to Element One. I don't know if this affects what I'm trying to do.
Phone # (MDN) 920xxxxxxx
MSID (MIN) 9202900444
SIN/NID 1/65535
MMS Server url mms.alltel.com/servlets/mms
I rooted the phone and got my MSL (000000) number and made the following changes
Phone # (MDN) 920xxxxxxx
MSID (MIN) 9202799238 (from Page Plus)
SIN/NID 240/65535 (got "240" from Page Plus, they couldn't give me a NID number so I used the same one)
MMS Server url mms.vtext.com/servlets/mms (got this from searching on forums)
I downloaded a .prl file via KittyWireless manual programming instructions kittywireless.com/pageplus/pageplusmanualprogramming.html
I updated the PRL from my sd card by dailing ##775# and "commit changes"
When I make a call, I'm always asked to re-enter the 10 digit phone number I'm trying to reach. I've tried the following OTA programming numbers *228, *22800, *22888, *22890, *22891. I always get the following "Message AP 32 Welcome to US Cellular ..." It should be Verizon or Alltel, right?
I thought I might be using the wrong NID number so I tried 65335 (which I think is for Verizon), but it didn't make a difference. Still roaming and same messages when I try OTA programming.
I don't know if this means anything, but when I dial ##DATA# to edit mode I can choose either Data Profile, EVDO, or Advanced. If I choose EVDO, I get a blank screen. I can't make any changes.
So, I'm thinking I need a different prl file. Would this affect my data connection for internet and MMS too? What do you guys think? Can someone direct me to the right PRL file?
I've spent hours trying to get this phone to work... if you have any suggestions let me know.
Thanks!
PRL Update...
Hi there..
I've found the following PRLs useful when using Sprint Phones on Pageplus, so perhaps they will help with the Alltel Hero. I've used 51425m on my Alltel Hero on Pageplus. Worked like a charm. The 52505m is the latest VZW EvDo PRL.
Noticed the thread is old, but may help anyone else trying to do this.
Ive been trying to get 3g data working with my Nexus S on Pageplus.
All I can get is either a good 1X data connection or a slow, intermittent 3g connection.
I will try these PRL's when I get home.
Thanks!
any luck on getting this working yet ??? I can not find any solutions anywhere
You contact your carriers
8=D
I am from the Android world, zero experience with WP7 and I want to buy this exact phone and possibly flash a custom ROM
and the goal is to get this to work on Page Plus (Verizon MVNO) and NOT Sprint
the phone is currently set up for C-Spire - a smaller CDMA carrier in Mississippi (formerly Cellular South)
I have access to CDMA workshop and other CDMA tools, such as qpst
I need Verizon coverage and a REAL keyboard at a cheap price ($55/month) and this looks like it could be the ticket!
I had the same question and found a post from bing searches with someone claiming to have succeeded in activating it on Page Plus. Unfortunately the person never really detailed how he did it.
I'd still like to know how it can be done.
The Arrive can be flashed to P+. I'm using one on it. You'll need the paid CDMAWS, not the hacked version.
Also, before you do this, remember that the 3G will be intermittent. The reason for this is that you cannot upload the authentication file to the phone's file system, so the phone never gets true 3G, it cycles between connecting and 1XRTT. To make this work properly, you'll need to have a ROM loaded that's a direct port from the HTC Trophy, or an Arrive ROM that has the Verizon operator package in it. I've yet to learn how to do this, but as time permits, I'll figure it out. I've got a few requests in to ansar and leadpoizon, two ROM Chefs that are heavily involved in GOLD_C (our phone's) development here.
Here's what I did:
1. Put the phone in Diag Mode, using ##MFG# on the phone dialer and connect to CDMAWS.
2. Obtain your MSL/SPC by using the HTC Method, then write it to 000000.
3. Program the phone using CDMAWS just as you would an android device; put in MIN, MDN and set your data settings to your#@vzw3g.com.
4. Load a modded PRL to put the phone on Verizon's Towers, and lose the roam triangle. (Attached)
5. Call P+ and give them the MEID of the Arrive. They'll tell you to do *22890, but do NOT do it.
6. Once they say it's active, make a test call, and enjoy your Arrive.
The steps above will give you voice calls, SMS, and spotty 3G. MMS will not work, unless you hack the registry of the phone. The phone works great with WiFi, though.
If you're brave, try forcing the phone into 1X by finding a non-EvDo PRL. You'll be showing that you're roaming, but it may yield better data results. If you do set 1X though, be sure to set MIP type (in CDMAWS) to Simple IP.
Post here w/ questions, if you have any...
I asked somewhere else but I found a lot of references here so I ask again
I would like to use my phone which is originally a US cellular phone on Page Plus network. I think it will make it much simpler for me to flash a Verizon cyanogenmod (not the stock one ) to my phone b/c of defaults network settings, etc.. I think that way it will work out of the box !!
Is it ok to do that or it will brick my phone ?
The reason I wanted to do so was because I was following some tuts about flashing USC phone to pageplus which required dialing *#22745927 to enable Tap Qualacomm USB Setting and DM+Modem+ADB or something like that.
But without the USC sim, the phone refused to accept *#22745927 or anything, it said network not available. With the USC sim in, the phone rang for a few secs then a voice said my account is not authorized.
That is why I thought I should flash the phone to VRZ to begin with.
I finally purchased a used Sprint S5 recently. My plan is to put the phone on the Boost Mobile Network. Boost Mobile stores are able to unlock my phone to Boost network, HOWEVER the MSL is needed. Well I'm sure you already know, Sprint is giving me a difficult time. A Sprint CS says the phone's ESN is clear to activate on Sprint, however due to "the way it was purchased" they could not unlock the phone (or give me the MSL) for other carriers. What do I do?
stevenp1200 said:
I finally purchased a used Sprint S5 recently. My plan is to put the phone on the Boost Mobile Network. Boost Mobile stores are able to unlock my phone to Boost network, HOWEVER the MSL is needed. Well I'm sure you already know, Sprint is giving me a difficult time. A Sprint CS says the phone's ESN is clear to activate on Sprint, however due to "the way it was purchased" they could not unlock the phone (or give me the MSL) for other carriers. What do I do?
Click to expand...
Click to collapse
On way is to activate it on someone elses account for just 5 minutes or so. Will give you chance to make sure it works. Then reactive their own phone and you're done. Now have your friend check his email and they will have an email from sprint thanking them for activating the new phone. Look at the email.. It will show some of the device specifics like model number, phone number and also an activation code. The activation code is actually your msl. It's a standard email from Sprint whenever you activate or reactivate a phone from your PC.
So find a friend with a Sprint phone and make sure the account is in his (or her) name. Have them log into their Sprint account on a PC and once they're logged in, scroll down to the "About My Devices" section. In this section you will see is a dropdown box that says "manage my devices". Click the down arrow in the box and choose, "activate new phone". It will take to you to a very straight forward wizard to guide you thru it. Choose no to all the options that they offer and when you get to the part of the activation about resetting the phone prior to activation, don't worry about it. Just click thru the steps of demo window that pops up then close that window after the demo is done. Once you finish the demo and close the pop up window you can continue. Follow the prompts until you click the activate button and turn off the phones as per the message that pops up. When you turn on your phone it will be activated with a voice and data signal. The whole process takes less than 5 minutes. Now check your friends email for your msl and you're done. Then do the same thing again but choose your friends phone to activate (as the new phone). Also note you will need the id numbers under the battery or have them ahead of time.
Ez
Thank you for the response I appreciate it. I will definitely consider. Is there any other method besides one mentioned above? I was thinking more along the lines of an apk like "Get MSL" to acquire the lock code. I've been utilizing the search function on both XDA and Google, but it seems that any method using an APK or program is defunct due to the new Software upgrade. Does anyone know of any other way?
Google GTv3.1.5.apk and GTUpdate2_v3.1.8.apk by idone.apps . The "GT" stands for Galaxy Tools; It will internationally unlock you sim as well as give you your MSL, enable hotspot etc... I beleive it was taken off google play, just google the 2 apk files and you'll find them.
So I bought the phone and a 35$ service card three days ago from Wal-Mart. Activated the phone around 3am that night. Phone hasnt worked once. No calling, texting or using data. Ive contacted ST CS numerous times with no help. Im told the same everytime. Dial *73 then turn off and back on, if that doesn't work repeat. Well it wont even let me dial * numbers. Pops up sim not registered, sim not provisioned, contact service provider. So whats what ive done. Yet they keep telling me my service and phone are active so they cant do anything. Ive seen a lot of people say to get an ATT sim and use that instead of the Verizon sim, and that will do the trick.
My phone number doesnt show up in settings. Network type doesnt. Cant edit or add or delete APN. PRL is blank in settings and no way to change it. Does anybody have any ideas or advice on what to do to fix all these issues???? I have 4 bars at all times but my service says 1x and yet i cant make calls or texts. Calls say im roaming and to buy a service card if I wanna make calls. Texts get stuck on sending then minutes later pop up they failed.
Rilynnsmamaxo said:
So I bought the phone and a 35$ service card three days ago from Wal-Mart. Activated the phone around 3am that night. Phone hasnt worked once. No calling, texting or using data. Ive contacted ST CS numerous times with no help. Im told the same everytime. Dial *73 then turn off and back on, if that doesn't work repeat. Well it wont even let me dial * numbers. Pops up sim not registered, sim not provisioned, contact service provider. So whats what ive done. Yet they keep telling me my service and phone are active so they cant do anything. Ive seen a lot of people say to get an ATT sim and use that instead of the Verizon sim, and that will do the trick.
My phone number doesnt show up in settings. Network type doesnt. Cant edit or add or delete APN. PRL is blank in settings and no way to change it. Does anybody have any ideas or advice on what to do to fix all these issues???? I have 4 bars at all times but my service says 1x and yet i cant make calls or texts. Calls say im roaming and to buy a service card if I wanna make calls. Texts get stuck on sending then minutes later pop up they failed.
Click to expand...
Click to collapse
Are you certain that you activated the device correctly and entered the SIM card number correctly when you activated the device?
Give me an accurate and descriptive breakdown of the exact steps you took when you activated the device and SIM.
BTW, AT&T SIMs are for GSM devices, not CDMA devices, if your device is a Straight Talk device, your device is a CDMA device. I doubt an AT&T SIM will help.
Sent from my LGL84VL using Tapatalk
Droidriven said:
Are you certain that you activated the device correctly and entered the SIM card number correctly when you activated the device?
Give me an accurate and descriptive breakdown of the exact steps you took when you activated the device and SIM.
BTW, AT&T SIMs are for GSM devices, not CDMA devices, if your device is a Straight Talk device, your device is a CDMA device. I doubt an AT&T SIM will help.
Click to expand...
Click to collapse
I mean, I'm assuming I did everything right lol. I followed the steps the ST website took me thru. Phones brand new, never been activated. Brand new sim. I went to the website, chose activate, chose I have a ST phone, input my zip, input IMEI, input SIM #, input service pin, created my account, updated profile settings, restarted phone. The app says my service is active, the website says its active, ST CS says its active on their end. But I can't call or text or use data. My network type is 1xRTT. I have 4-5 bars at all times. When I try to call regular numbers, I get a "you are roaming, to place calls please purchase a service card" or something along those lines. When I try to call *73 like ST keeps telling me, it says sim not registered, sim not provisioned, contact service provider.