Related
Hello,
I have weird problem with my Samsung captivate.
I install a new rom on my device and it work well for several hours but than it suddenly stop to work.
After a reset my device get stuck on the at&t screen.
I entered the download mode and flashed clean rom with odin (and check the Master Clear option).
But it still get stuck on the at&t screen.
Is this can be hardware problem?
Is there any way to get the log file from the boot to find out what is the problem?
Double post
Sent from my GT-I9000 using XDA Premium App
matsog said:
Hello,
I have weird problem with my Samsung captivate.
I install a new rom on my device and it work well for several hours but than it suddenly stop to work.
After a reset my device get stuck on the at&t screen.
I entered the download mode and flashed clean rom with odin (and check the Master Clear option).
But it still get stuck on the at&t screen.
Is this can be hardware problem?
Is there any way to get the log file from the boot to find out what is the problem?
Click to expand...
Click to collapse
If you can get in recovery, do a factory reset.
Also, you can reflash with Odin3 one click downloader. If you get the AT&T boot loop again, remove the battery, wait 5min.. and turn back on your phone.
Don't forget that after a flash it can take quite a while before the phone boots up as it has to rebuild his dalvik cache.
You can use UART to get the information.
Here's my setup. This is still a work in progress.
adam, i got some stuff to make those connectors but i think it's gonna have to wait till after finals. just a couple weeks and ill let you know if i have any luck.
the .008" endmills i need are $24 each, god forbid i break one! i can try a .010"endmill to keep the cost down(i found .010" endmills for about $10 from a different supplier). but then the contacts will be .005-.006" wide not .008" and are more likely to break and pull off the board in the process. im gonna try something else first, maybe it can still be done chemically if i'm carefull.
then you should have what you need to jtag the phone so you can test this more fully.
Dani, this is not the right topic, however thank you.
ok droid charge was rooted went to restore back to stock unrooted (was going to sell it) tried to flash using Odin with the pit file and stock one Odin went about half way and had a error phone turned off i tried to get the phone back into download mode to restart the process but i can't get the phone into download mode also i can't get the phone to boot up no Samsung logo nothing any help would be greatly appreciated the phone will not do anything at all i need help i have tried p3 Samsung pst method but still nothing
thanks
dustin4863 said:
ok droid charge was rooted went to restore back to stock unrooted (was going to sell it) tried to flash using Odin with the pit file and stock one Odin went about half way and had a error phone turned off i tried to get the phone back into download mode to restart the process but i can't get the phone into download mode also i can't get the phone to boot up no Samsung logo nothing any help would be greatly appreciated the phone will not do anything at all i need help i have tried p3 Samsung pst method but still nothing
thanks
Click to expand...
Click to collapse
just curious what methode are you using to enter download mode? Did you try recovery for giggles?
i have tried both download mode and recovery and just trying to let it boot up normal and it will not do anything in all three just a black dead screen
Try leaving the battery in when you go to download mode. Also leave it in when flashing.
if it wont even power on in any way or go into the download mode you might be bricked...I did this before and I had to exchange it at Verizon..luckily since it wouldnt turn on they couldnt tell what I did to it...hope you can get your issue resolved
Ha a true brick. Finally someone using the terminology correctly. A buddy of mine has this happen with his galaxy s. He got it exchanged in store no questions asked. btw Sorry to hear about your phone
Sent from my ADR6350 using XDA App
1/2 Brick
Hi
Sorry to hear about your issue. I am at half brick now. Been at multiple spots learning here but never completely no visability! 3/4, 7/8, right now in a flash it does not see my phone (no network) data side is fine but can not get or receive calls. It is not the SIM card (according to VZW). Data side works fine 4G etc, emails but no phone. A great PDA but not a phone. No one has answers but I belive to be a cp_modem.bin issue download hangs at around 98% in what does a boot 2nd boot on the screen in the download then says:
Wait, VIA Booting ..
VIA rest done. ..
Downloading to VIA...
To everyone the {Kangfuscius.tar} has helped me when I thought all hope was lost, even in a partial download it helped to bring me back.
Any suggestions on files for the phone tab in ODIN all I can think of is, it can't get worse. The FEDEX guy kow knows me by name between the Fascinate's and now I guess the Charge.
Any help appreciated,
norm883
norm883 said:
Hi
Sorry to hear about your issue. I am at half brick now. Been at multiple spots learning here but never completely no visability! 3/4, 7/8, right now in a flash it does not see my phone (no network) data side is fine but can not get or receive calls. It is not the SIM card (according to VZW). Data side works fine 4G etc, emails but no phone. A great PDA but not a phone. No one has answers but I belive to be a cp_modem.bin issue download hangs at around 98% in what does a boot 2nd boot on the screen in the download then says:
Wait, VIA Booting ..
VIA rest done. ..
Downloading to VIA...
To everyone the {Kangfuscius.tar} has helped me when I thought all hope was lost, even in a partial download it helped to bring me back.
Any suggestions on files for the phone tab in ODIN all I can think of is, it can't get worse. The FEDEX guy kow knows me by name between the Fascinate's and now I guess the Charge.
Any help appreciated,
norm883
Click to expand...
Click to collapse
I don't know why your phone is booting into 'VIA' mode and don't even know what that is so I couldn't say a fix other than odining the usual stock rom/pit combo (leaving the battery in when flashing in odin also and uncheck the 'auto reboot' option)... also phone tab/button is NOT supposed to be touched in odin, only PDA, PIT if needed, and Start
Where did it fail in the Odin flash? The only way you should be bricked is if it failed while flashing boot.bin or sbl.bin, otherwise, it should still go to download mode. Have you tried using one of the Force Download Mode jigs/dongles that the GSM models use to get into download mode?
i don't recall where it failed at but it will not not respond to anything with batt or without where can i find the gsm software i will give it a try before i call insurance a link or anything would be great
what gsm models are equivalent to the charge
dustin4863 said:
i don't recall where it failed at but it will not not respond to anything with batt or without where can i find the gsm software i will give it a try before i call insurance a link or anything would be great
what gsm models are equivalent to the charge
Click to expand...
Click to collapse
Infuse 4g or SGS 2 unlocked.
Sleek69 said:
Infuse 4g or SGS 2 unlocked.
Click to expand...
Click to collapse
SGS2 is not equivalent. Just search for galaxy s download jig and i'm sure you'll find what I'm talking about. It is the same thing for all the SGS phones, and some have said it works on the 4G versions of the phones as well.
dustin4863 said:
ok droid charge was rooted went to restore back to stock unrooted (was going to sell it) tried to flash using Odin with the pit file and stock one Odin went about half way and had a error phone turned off i tried to get the phone back into download mode to restart the process but i can't get the phone into download mode also i can't get the phone to boot up no Samsung logo nothing any help would be greatly appreciated the phone will not do anything at all i need help i have tried p3 Samsung pst method but still nothing
thanks
Click to expand...
Click to collapse
Hi, I had the same thing happen to my first Charge. I could not boot my phone even to the samsung logo, so I searched around the Internet. Somehow I think it was the Captivate trick worked. I took out sim, battery, sdcard>plugged in usb to computer>held up and down volume together>put in battery; miraculously it went to download. I tried every other combination beforehand and none worked, so I know this method works.
Unfortunately this was before we had IMNUTS Pit file and a odin flash would not change anything so I could not recover and I flashed a Pit that was not for the Charge. Wrong answer! After that it was in the non-boot state again but the same method above would not work any longer. If your phone does not work with the method above, maybe something went wrong with the repartition and pit file. That is just a guess though!
well the jig hasn't worked yet i am running right at 300k tomorrow i am going to get a 1k and add that in also and see if that helps. also pulling all the cards and the battery didn't work either. this is not looking good i am up for any ideas that anyone has
thanks
dustin
Hey guys found a way to unbrick Samsung droid charge and revert back to stock.
1. Download and install Odin found here ( http://forum.xda-developers.com/show....php?t=1085190 ) unzip and open
2.Download this file and unzip ( CI510_VZW_EE4_ALL_ONE-LTE-CP_REV03_user_CL1014954.tar.md5.7z) from here ( http://www.multiupload.com/6WJ2SFUKO6 ) or original thread where i found this file is from here ( http://androidflip.com/android-2-3-4...talling-guide/ )
3. set phone to download mode, do this by taking battery of phone, plug phone into computer and hold Volume down, a Yellow triangle with a working android will appear.
4. Click on odin you will see your phone come up under ID:COM, now do not click on anywhere but on PDA thats where you will have to find the file you downloaded on step 2 and make sure is the unzipped file. once u find it, click on open then start.
5. Be patient this can take up some time, once is done the box will turn green and say pass, at this time your phone will no longer have the Yellow triangle and you can unplug and place the battery back in and turn phone on.. once again be patient when turning phone on it will take a little while to complete.
i tried this and it does work, my Droid charge was bricked and now it works.
Thanks to xda-developers where i was able to find odin and also thanks to androidflip.com where i was able to find the Droid Charge stock rom to flash it back using odin.
Hope this helped everyone needing help.
dustin4863 said:
well the jig hasn't worked yet i am running right at 300k tomorrow i am going to get a 1k and add that in also and see if that helps. also pulling all the cards and the battery didn't work either. this is not looking good i am up for any ideas that anyone has
thanks
dustin
Click to expand...
Click to collapse
Dustin, were you able to get it working? I'm in the same boat. Right after boot.bin it failed. Which was within seconds after hitting the start button in Odin. Verizon won't honor my warranty, because I didn't buy the phone from them.
Hard Brick Fixed
If you are truly hard bricked (no download mode, no power, no nothing), you can get it fixed for $40 at mobiletechvideos.com. I flashed a file that didn't work unless I took off the md5 extension. Big mistake. After trying absolutely everything, including surfing the internet for a day, spending almost $20 to get 2 day delivery for a USB Jig that did absolutely nothing, I sent my phone to mobiletechvideos.com. Josh brought it back from the dead; don't know how, but it was the best $40 I ever spent! I think there aren't any reviews because there haven't been enough newbies like me who just can't wait for Gingerbread and bricked their Samsung Charge. Putting my review there tonight...should be first one. The reviews from all the other phones he has unbricked convinced me to try and I'm glad I did.
Many people have hard bricked their phones trying to downgrade. Give the jig a shot, but don't hold out much hope.
Personally I think there is something being overlooked during the downgrade process... Too many people are hard-bricking during the process for it to be coincidence.
Oh yes
mgsparro said:
If you are truly hard bricked (no download mode, no power, no nothing), you can get it fixed for $40 at mobiletechvideos.com. I flashed a file that didn't work unless I took off the md5 extension. Big mistake. After trying absolutely everything, including surfing the internet for a day, spending almost $20 to get 2 day delivery for a USB Jig that did absolutely nothing, I sent my phone to mobiletechvideos.com. Josh brought it back from the dead; don't know how, but it was the best $40 I ever spent! I think there aren't any reviews because there haven't been enough newbies like me who just can't wait for Gingerbread and bricked their Samsung Charge. Putting my review there tonight...should be first one. The reviews from all the other phones he has unbricked convinced me to try and I'm glad I did.
Click to expand...
Click to collapse
Doing so NOW! For the same issue. My PC decided to spontaneously reboot during ODIN while flashing a ROM on My Droid Charge. Josh was quick to respond to EVERY single annoying question I had about their service. So I am doing so. If it works, I'll tell you, I'm adding a link to their site in my signature on every forum I'm a member of, even forums I have for my daughter's schooling hahaha! They deserve the references just for being quick to respond. Thanks for the info man, props to you.
First,sr for my bad english.
Yesterday at noon,i was trying to get to JFD on Odin,but the phone keep rebooting after i did that,so i did a master clear,but i waited for 30 minutes and nothing happened(the yellow bar still appeared through..),so i pulled the usb cable out and then i tried to get to download mode again,but nothing came up.I tried using all the methods that i read,but still could not get into download mode or boot the phone up.So i'm very scared right now.
I hope that you will help me solve this problem.
alonecat said:
First,sr for my bad english.
Yesterday at noon,i was trying to get to JFD on Odin,but the phone keep rebooting after i did that,so i did a master clear,but i waited for 30 minutes and nothing happened(the yellow bar still appeared through..),so i pulled the usb cable out and then i tried to get to download mode again,but nothing came up.I tried using all the methods that i read,but still could not get into download mode or boot the phone up.So i'm very scared right now.
I hope that you will help me solve this problem.
Click to expand...
Click to collapse
Are you on a Galaxy S 4G? I believe JFD is a ROM for the Vibrant, not the SGS 4G.
If you did, you might want to try AdamOutler's unbrickable mod:
http://forum.xda-developers.com/showthread.php?t=1333424&highlight=unbrickable
is there an easier way to fix it im running windows so i cannot use unbrickable resurector,and i dont have any experience with fixing hardware
alonecat said:
is there an easier way to fix it im running windows so i cannot use unbrickable resurector,and i dont have any experience with fixing hardware
Click to expand...
Click to collapse
I really wish I knew of another way. You could try searching the forums a bit; there might be a way, but usually if the wrong boot loaders were installed you'd have to follow the link I sent, use a jig (which I know nothing about) or something of that nature.
I wish you luck.
What phone do u have?
i posted in this box so obliviously i have a SSGS4GT.T
Umm,can i ask u one more question?
Can i use JIG to trick the phone go into Download mode?_?.
While I was flashing a ROM (Synergy1.3), my wife decided to move my phone to another table. When i looked at it a few minutes later,the screen was blank. Now it wont turn on at all. I had used that particular ROM before without any problems. My battery was at 90% when i started to flash. I have a terrible feeling i am bricked. Any ideas?
goralla said:
While I was flashing a ROM (Synergy1.3), my wife decided to move my phone to another table. When i looked at it a few minutes later,the screen was blank. Now it wont turn on at all. I had used that particular ROM before without any problems. My battery was at 90% when i started to flash. I have a terrible feeling i am bricked. Any ideas?
Click to expand...
Click to collapse
You take out the battery..then try it?
Dominazn said:
You take out the battery..then try it?
Click to expand...
Click to collapse
yes,also tried charging it from wall charger ans USB. I get this error when plugging into USB (QHSUSB_DLOAD)
It's hard to brick a phone. Worst case, boot into download mode and Odin up the stock image.
If you can't access Download mode, you've most likely bricked as any research I've done points to it. If you've got insurance you can pay the premium, or send it to one of the JTAG services for repair (such as MobileTechVideos).
Just don't leave or touch the phone next time when you're flashing!
With my case it's hard to hit the buttons for recovery and download. I created across to get to them. Not what you're wanting to here. But here's a tip: if you can get adb to recognize your phone but can't use buttons to get into download mode you can "adb shell" and then "reboot download". That will cause the phone to boot download/Odin mode. Hopefully that will work and you can flash back to stock.
Sent from my SCH-I535 using xda app-developers app
The phone will not power up in any way at all. I am in the 5th stage of the grieving process. Back to my Tbolt and hope Samsung honors the warranty.
goralla said:
The phone will not power up in any way at all. I am in the 5th stage of the grieving process. Back to my Tbolt and hope Samsung honors the warranty.
Click to expand...
Click to collapse
They won't honor it with a rooted phone or flash count pass 0
Sent from my Verizon Samsung Galaxy S3 4G LTE
If you cant get to download mode or get adb to recognize when properly set up you do probably have a brick. What's happening to you with the warning happened to my friend on Sprint while accidentally flashing a ROM for a different phone. What he had to do was send it in to MobileTechVideos and got it repaired for around 60$. Samsung/Verizon wont likely fix them under warranty.
My only question is if you indeed were flashing synergy, how did a system ROM brick a device. o_0 And hell even if it was another phones ROM wouldn't our locked bootloader deny overwriting?
enomele said:
If you cant get to download mode or get adb to recognize when properly set up you do probably have a brick. What's happening to you with the warning happened to my friend on Sprint while accidentally flashing a ROM for a different phone. What he had to do was send it in to MobileTechVideos and got it repaired for around 60$. Samsung/Verizon wont likely fix them under warranty.
My only question is if you indeed were flashing synergy, how did a system ROM brick a device. o_0 And hell even if it was another phones ROM wouldn't our locked bootloader deny overwriting?
Click to expand...
Click to collapse
I also accidentally flashed a rom for a different phone and am considering sending it to MobileTechVideos. Your friend had good success with them fixing his phone?
-Purk
I think this might also work for you, if the battery charging icon comes on while your charging it then this might work. When you have it connected and the charging icon comes on put it in download mode(do not unplug it until your in download mode). Then use odin to flash it back to stock. It happen to me ones and when i did this it work for me, so i don't know if this will work for you. (Sorry for my grammar)
Good Morning Everyone, This is my first post. I try to never post just read. I have read and read but to no avail. I have a AT&T Samsung infuse 4g. it WAS running froyo. What I mean by WAS, is that I was trying to install the modded 3e recovery so I could install clockworkmod recovery. During this process I read that I need to mount the /system partition as read/write I did this using the tool box that was created by some of your developers. It is awsome by the way. Well I did that and put a new recovery file in the /bin but it did not work as the website claimed so I thought well I should delete the old one. Bad Idea when I did the reboot it stopped me at the samsung screen. I tried to hard reboot it pulled the battery talked to it with a really kind voice and nothing happend. So I decided to use GEG's Ultimate Unbrick because this has worked for me in the past when i have messed up. So I put my phone into download mode and started the process with Odin. And here is where it gets bad.... one of my children was talking with me during the process and he decided to unplug my phone.. AHH EFFFFFF! I thought. Well when I tried to fix it it was to late. My phone will no longer turn on or even pretend to start. I am broke and cannot afford a new phone plus my wife would kill me seeing we have 6 children and it is right before christmas if I came home with a new galaxy note 2 Please Please can any one help a desperate dad with a busted Samsung Infuse. Thank you all for this awesome website that has taught me alot.. Please dont kill me for posting something someone has already posted because I could not find anything that was helpful for this situation with my phone.
Xda is awesome!
Well I didnt read good enough I guess because while I was waiting not so patiently for a reply I found this http://forum.xda-developers.com/showthread.php?t=1194294 which got me back to download mode yes!!!! Thank you thank you thank youXDA love you guys! Merry Christmas! PS I still want the Galaxy Note 2 so if you have a extra one please PM me and I will give you my address LOL!
MerkTheMedia said:
Well I didnt read good enough I guess because while I was waiting not so patiently for a reply I found this http://forum.xda-developers.com/showthread.php?t=1194294 which got me back to download mode yes!!!! Thank you thank you thank youXDA love you guys! Merry Christmas! PS I still want the Galaxy Note 2 so if you have a extra one please PM me and I will give you my address LOL!
Click to expand...
Click to collapse
Awesome! Glad you got your phone functioning again. Being persistent in searching and reading and trying to find answers usually results in good outcomes. :thumbup:
Sent from a de-Funkt Infuse
Okay now I have really done it this time. So I worked a 18 hour day and thought well instead of getting some rest i will install Gingerbread on my infuse. To make a long story short while I was using odin to install it paused for a long time at the format stage, so I thought well I will just turn it off even though it says not to and then.....well it did a rainbow colored screen I tried to figure it out last night with no luck. So I have been working on it all morning the rainbow screen is gone but now it just goes from black to all white screen. I have tried every possible way to get into download mode with no luck. Am I screwed or what? Does anyone have any suggestions. If I am out of luck does anyone know if bestbuy's warrenty covers rooted phones that are [email protected] bricked?
You just need To update your boot loader.
You can navigate in the screwy screens but it takes patience and some guesswork. Been there
Also...
Good instructions here
http://forum.xda-developers.com/showthread.php?p=14550608
USB cables have given me issues as well as drivers. Install Kies to get the drivers.
Another...
http://forum.xda-developers.com/showthread.php?p=23118134
Sent from my SGH-I997 using xda app-developers app
Sent from my SGH-I997 using xda app-developers app
saxk said:
You just need To update your boot loader.
You can navigate in the screwy screens but it takes patience and some guesswork. Been there
Also...
Good instructions here
http://forum.xda-developers.com/showthread.php?p=14550608
USB cables have given me issues as well as drivers. Install Kies to get the drivers.
Another...
http://forum.xda-developers.com/showthread.php?p=23118134
Sent from my SGH-I997 using xda app-developers app
Sent from my SGH-I997 using xda app-developers app
Click to expand...
Click to collapse
It still will not get me into download mode it is powering on and off connecting and disconnecting I have the drivers installed I have tried gtg's guide I have tried qstars one click nothing is working. These have worked for me in the past but that was because I can get into down load mode. Unfortunately not any more Is there a way to make the phone stay on and connected so it stops going black to white to black screen? I am so bummed out! I have been reading for so many hours my brain hurts. I have learn a ton but I can't do anything with my new knowledge with no phone!!!AAAHHHHHH
MerkTheMedia said:
It still will not get me into download mode it is powering on and off connecting and disconnecting I have the drivers installed I have tried gtg's guide I have tried qstars one click nothing is working. These have worked for me in the past but that was because I can get into down load mode. Unfortunately not any more Is there a way to make the phone stay on and connected so it stops going black to white to black screen? I am so bummed out! I have been reading for so many hours my brain hurts. I have learn a ton but I can't do anything with my new knowledge with no phone!!!AAAHHHHHH
Click to expand...
Click to collapse
if you're boot looping in the samsung logo, it could be your power button. search for how to fix power button
qkster said:
if you're boot looping in the samsung logo, it could be your power button. search for how to fix power button
Click to expand...
Click to collapse
Qkster its a honor to have you comment on my thread, Unfortunately Im not boot looping to the samsung logo it is just a black then white then black back and forth taunting me with every blink. I did read the thread about the power button earlier though and that is unfortunately not the fix either. I do appreciate the input you guys really do try and help! Maybe you can answer a question for me is there a way to get to the phone through command prompt? I really need this phone fixed. My wife has been telling me I shouldnt be messing around with it because im gonna break it. I really dont want to tell her she was right. I will never hear the end of it lol!
MerkTheMedia said:
Qkster its a honor to have you comment on my thread, Unfortunately Im not boot looping to the samsung logo it is just a black then white then black back and forth taunting me with every blink. I did read the thread about the power button earlier though and that is unfortunately not the fix either. I do appreciate the input you guys really do try and help! Maybe you can answer a question for me is there a way to get to the phone through command prompt? I really need this phone fixed. My wife has been telling me I shouldnt be messing around with it because im gonna break it. I really dont want to tell her she was right. I will never hear the end of it lol!
Click to expand...
Click to collapse
You're too kind, Merk.
I'm not sure what happened to your phone. The Infuse is pretty sturdy. Flashing should not cause much of an issue. The faulty power button and corrosion of the circuit board were the most I've seen reported.
This is what I use to force the phone into download mode:
http://www.ebay.com/itm/Micro-USB-J...665854?pt=PDA_Accessories&hash=item3f201c4f3e
Once in DL mode, it's a matter of choosing Odin or Heimdall to bring it back to stock.
One other thought, try a different battery as well.
I had the same exact problem. If the only thing the phone will do is go into download mode, then Samsung will fix it (if your still under warranty). They fixed mine and sent it back to me. Then I tried to flash another ROM on there and while it was flashing, I went to the store, and when I came back it said failed. Then it would only go into the other download mode. The one that has this (phone...!...PC). It wouldnt show up on odin 1.7 anymore. So I ended up trying a USB cable for my HTC evo v, and the drivers installed, then it popped up on Odin. I used G2G's Ultimate Unbrick (dude is a f-ng genius, all credit goes to him) and instead of putting the pit, PDA, and phone file on there and flashing, I flashed one at a time......then....I went back and flashed all at once and everything worked perfect. If your still having trouble with it, I can tell you exactly how I did it, and maybe that will work for you. Sorry to but in on this post and sorry it was so long of a reply. I just no what its like when you half brick an infuse. Mine was like that for 6 months because I couldn't get any computer to recognize it. But anyway, I hope I was helpful.
Sent from my SAMSUNG-SGH-I747 running CM10 4.1.2 JB using xda premium
michaelsinbad said:
I had the same exact problem. If the only thing the phone will do is go into download mode, then Samsung will fix it (if your still under warranty). They fixed mine and sent it back to me. Then I tried to flash another ROM on there and while it was flashing, I went to the store, and when I came back it said failed. Then it would only go into the other download mode. The one that has this (phone...!...PC). It wouldnt show up on odin 1.7 anymore. So I ended up trying a USB cable for my HTC evo v, and the drivers installed, then it popped up on Odin. I used G2G's Ultimate Unbrick (dude is a f-ng genius, all credit goes to him) and instead of putting the pit, PDA, and phone file on there and flashing, I flashed one at a time......then....I went back and flashed all at once and everything worked perfect. If your still having trouble with it, I can tell you exactly how I did it, and maybe that will work for you. Sorry to but in on this post and sorry it was so long of a reply. I just no what its like when you half brick an infuse. Mine was like that for 6 months because I couldn't get any computer to recognize it. But anyway, I hope I was helpful.
Sent from my SAMSUNG-SGH-I747 running CM10 4.1.2 JB using xda premium
Click to expand...
Click to collapse
Well im going to give it a shot I still have the old infuse I tried to make my own jig which didnt work for me so I took it into bestbuy and they gave me a brand new phone and in all of the hustle and bustle of christmas shopping going on around me they did not take my bricked infuse so now I have a spare to tinker with. Thanks I will definately give it a try and report with my findings
Sent from my SAMSUNG-SGH-I997 using xda app-developers app
michaelsinbad said:
I had the same exact problem. If the only thing the phone will do is go into download mode, then Samsung will fix it (if your still under warranty). They fixed mine and sent it back to me. Then I tried to flash another ROM on there and while it was flashing, I went to the store, and when I came back it said failed. Then it would only go into the other download mode. The one that has this (phone...!...PC). It wouldnt show up on odin 1.7 anymore. So I ended up trying a USB cable for my HTC evo v, and the drivers installed, then it popped up on Odin. I used G2G's Ultimate Unbrick (dude is a f-ng genius, all credit goes to him) and instead of putting the pit, PDA, and phone file on there and flashing, I flashed one at a time......then....I went back and flashed all at once and everything worked perfect. If your still having trouble with it, I can tell you exactly how I did it, and maybe that will work for you. Sorry to but in on this post and sorry it was so long of a reply. I just no what its like when you half brick an infuse. Mine was like that for 6 months because I couldn't get any computer to recognize it. But anyway, I hope I was helpful.
Sent from my SAMSUNG-SGH-I747 running CM10 4.1.2 JB using xda premium
Click to expand...
Click to collapse
okay I tried but that didnt work either. Can you go ahead and explain "exactly" what you did maybe it will work!
Thanks again for everyones help!
Ok first I downloaded the unbrick package from this website. I downloaded the drivers for the infuse (not sure exactly where I got them from). I would just Google them. Then I tried every USB port on the laptop. Then switched cables and it finally worked. Opened Odin 1.7 and clicked pit, then flashed. Then I unplugged it, took the battery out and put back in and tried to boot. Didn't work. Then flashed PDA. Did same steps as before and still didn't work. Then flashed phone file. Tried to boot and still didn't work. Then I flashed all 3 files at once. Also, not sure if you know or not but the only thing that should be checked in Odin is f: reset time. Then the phone booted up and it stayed on at&t screen for about 5 minutes then finally came on. Also, you could also try to flash this other PDA file on there. I have the link saved on my computer but I'm not at home right now so I'll have to post that later. In easier steps
1. Put phone in Download mode and plug into pc.
2. Run Odin as admin and only thing checked is f reset time.
3.Flash pit then try to boot
4. Flash PDA then try to boot
5. Flash phone then try to boot
6. Flash all three at once
7. After flash While in download mode, unplug USB cable, take battery out and put back in
8. Reboot phone.
Sorry everything is all jumbled, I just got back to my home state from a road trip and I'm running on about 6 hours of sleep in 3 days. I hope this works for you. Also, there is a video on YouTube of a unbrick service for the phone. Its $30. I personally would not try it but its just an idea if you would want to.
Sent from my SAMSUNG-SGH-I747 using xda premium
I had the issue where I had the phone, the exclamation mark, and the computer symbol (The Black Screen of Death: Imaged Attached), that is all it would show when I turned it on. I thought the phone was completely bricked until I did the following, which put it into a hidden download mode and allowed ODIN to recognize it. I DID NOT NEED TO BUY A USB JIG.
1. Make sure you have Odin already downloaded and ready to go.
2. Remove the SIM and SD Cards
3. Load up Odin and make sure it is up and running on the computer. DO NOT plug your phone into the computer yet.
4. Reinstall the Battery and plug the phone to the USB cable to the computer.
5. Hold down both Volume keys and then push and hold the power button
6. Keep holding the buttons until it goes to black, KEEP HOLDING A SECOND TIME until it goes to black and the icon comes back on.
7. Now when it goes Black the second time release the Power button only.
8. You should now be in Download mode. The key is holding the buttons, letting it go to black once, and then letting it go to black again, and then release only the power button while your fingers are still on the volume buttons.
9. Now Odin should recognize the phone on a Com port (turn yellow).
10. You are now ready to return it back to stock.
I hope this helps!
did you ever get your infuse fixed man?
Sent from my SAMSUNG-SGH-I747 running CM10 JB 4.1.2 using xda premium
Yes I tried to make my own jig but my fat shaky hands could get the end of the wires to hit the correct contacts so I ordered one online and that got me into download mode! Now I'm running jelly bean! Thanks to everyone that helped out I love you guys!!!! PS. Don't skip backing up your efs folder!! Unless you want a headache. But with all my problems it has taught me a lot. My number one tip is to read read read there is always an answer! Thanks again everyone! Always hit the thanks button its the least we can do for all of these brilliant hard working developers.
Sent from my SGH-I997 using xda app-developers app