Related
hey guys,
my phone litteraly wont do anything. i f*ed up some fonts using type fresh, then tried to restore using the odin3 downloader. i accidentally closed it, and now my phone wont boot up/react to any buttons pressed. any help? thanks guys!
had the same problem. i cant figure out how to even get odin working, it says one click but when i hook up it to odin it gives me a message that still doesnt tell me ****. i had to send my phone back for a new one and told them i used easyroot on the market bc i didnt know what it was and it sounded cool but now i know not to ever do that again that it messd up my phone. Praying to god that they dont charge my for anything
You should still be able to enter bootloader mode by turning phone off and holding down up/down vol and pwr simultaneously until boot screen flashes then release power button only
it wont even do that
open odin (use the stock one click version)
with the phone off (remove/reinsert the battery if need be) and not plugged in; hold vol. down and insert the usb cable (keep holding vol. down untill you see the download screen). this should put you into download mode and if you have the right drivers odin should recognize the phone.
I've stuffed my captivate on a few occasions and so far I have been able to use this method to get into download mode and fix it.
it wont do anything at all. it wont power on, show up in adb, anything... and stupid att wont do ANYTHING -_- oh well. any help would be appreciated!
Have any of you offering support to the OP actually had your phone in the described state? I've read a few posts where the phone is seemingly completely dead as the OP describes and no one says they've successfully recovered from that state. All I ever see is the same old button combinations/battery/usb shenanigans and statements of that should work and that the phone is unbrickable. I have personally seen a device that was behaving in such a manner and no combination of battery pulling, usb plugging, button holding, or tongue twisting would generate anything from the phone. The only thing the phone would do was get hot.
same here. Phone showed bright green screen...wasnt done with teh flash and said it was finished...now the nly thing I can get is power and hold the vlume up for some IRQ and hex stuff. I posted a questionthis morning but...serious. Vol up and down and any things else gives nothign but a black screen..battery out...back in anything..its torched.
Have you tried getting into download mode via the sdk?
Sent from my SAMSUNG-SGH-I897 using XDA App
daveshih said:
Have you tried getting into download mode via the sdk?
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
when i plug it in, windows doesnt make any noises and doesnt recognize it, and when i use the "adb devices" command, nothing shows up.
daveshih said:
Have you tried getting into download mode via the sdk?
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
Did you read the rest of the posts? The OP already stated several times that the phone does nothing. I realize that most people will say it does nothing or is "bricked" if it simply shows the "connect to computer" screen, but the OP has stated more than once that the phone shows nothing. Yes, everyone is trying to help, but simply repeating what has been said numerous times before doesn't help.
Has anyone actually recovered a phone that displays NOTHING? No logos, no recovery, no nothing.
Last night, i turned off the light in my room when i noticed a glowing from my desk. i walked over, and it turns out my captivate's screen was in fact on, it was just a faint black glow, and none of the power buttons would do anything. when i took the battery out, it shut off completely!
As I pointed out here
http://forum.xda-developers.com/showthread.php?t=757293
Im pretty sure it was my fault for not completely following instructions on the ext4 one click install root, settings.db etc so everyone needs to make sure if the dev says flash before..do it.
State of the phone was, it would not completely power on..therefor no usb drivers would load and Odin cannot see the phone and it can no longer flash..the only thing I could get it to do was show a screen with that text. I put in my post. I ordered it via letstalk.com so I sent it back and assuming they get the same result Ill have a new one hopefully by the end of the week. Im just glad I stil had my old iphone3 to slap my sim card in.
The odin one click flash thing..it just flaked right at the start it looked like..but I cant be sure because as soon as I saw a blue progress bar I stepped into the kitchen for abtou 30 sec..I came back and the screen was florescent green and Odin said it was done. I knew something was wrong as it was way too fast so I unplugged, removed the battery and set it back in...from there on out it would do nothing with the power button unless on a semi rare occasion if I hit the volume up button and power I got the IRQ stuff.
Annoying as I had a nandroid backup just before I started messing with it.
i just sent mine into samsung... back to mah ol trusty blackjack. gonna have to get used to supermario bros 3 instead of spyro....
ANYWAYS theyre sending me a new one!
uiskibum said:
open odin (use the stock one click version)
with the phone off (remove/reinsert the battery if need be) and not plugged in; hold vol. down and insert the usb cable (keep holding vol. down untill you see the download screen). this should put you into download mode and if you have the right drivers odin should recognize the phone.
I've stuffed my captivate on a few occasions and so far I have been able to use this method to get into download mode and fix it.
Click to expand...
Click to collapse
So, yes in same state as op... no nothing... couldn't get jack out of it. at all, none
what this post said worked.... not holding power button... nothign...
removed battery
plugged in battery
hold vol down
(still no response)
plug in usb cable and continue holding vol down.
it went to recovery mode
... no holding of power button, just vol down and plugged in USB... give it a shot man, let me know
EDIT: feel free to PM me if you want me to help walk you through it...
ace518 said:
So, yes in same state as op... no nothing... couldn't get jack out of it. at all, none
what this post said worked.... not holding power button... nothign...
removed battery
plugged in battery
hold vol down
(still no response)
plug in usb cable and continue holding vol down.
it went to recovery mode
... no holding of power button, just vol down and plugged in USB... give it a shot man, let me know
EDIT: feel free to PM me if you want me to help walk you through it...
Click to expand...
Click to collapse
Hey thanks, but i already sent it to em... thank you everyone for your help!
Just a note... i said before hold vol down and plug in usb. I had it in a pretty bad state tonight. Played around. Same idea as before, but had to hold vol up and vol down. If i brick a few more times, i'll give a better guide. But this phone can DEFINITELY come back from a state where you can't even get it to power on. Figured any additional info on this would be good.
Ok I was flashing back to stock 2.1 useind odin when mid process my phone fell battery out usb disconnected and bam thats it. Now my phone is locked on a screen that shows a picture of a phone ! and a computer. I can get it back to download mode and odin will se the phone but gets no further then do not unplug device, my computer beeps when its plugged in but it dose not show the phone in my computer section. Any fixes or am i screwed?
PS phone is only two weeks old if need be could I take it back like this????
Hmm I think I may hove gotten past this problem. Uninstalled odin reinstalled and now it seems to be hopefully working
Here is the fix
I was in this same situation yesterday. Here is how to get it back into download mode.
•Be sure the Samsung USB drivers for the phone are installed on your computer.
•Remove and replace the battery.
•Connect the phone to the computer with the USB cable. The "phone-exclamation mark-computer" picture should display on the phone's screen.
•Hold the Volume Up+Volume Down+Power buttons down simultaneously.The screen should go blank, then the picture should appear again. When the screen goes blank a second time, release the Power button while continuing to hold the Volume Up+Volume Down buttons down
If that doesn't work,i had a similar problem where I could get into odin, but it would progress beyond the pit file. Take the battery, sim and memory card out of your phone. Start odin. Put the battery only back in. hold volume up and down. Plug the phone in while holding these buttons. Don't let go until you are in download mode. Now try restoring. It should work.
Thanks for the input i am back up and running!!
Sent from my SAMSUNG-SGH-I897 using XDA App
Bricked replacement Captivate - Orange Screen
Just to let you know. I recently received a replacement captivate thru warranty exchange. The phone was apparently a new one with JF6. So I decided to do an update to JH7 using Kies mini. A little over half way to the update procedure, the phone screen turned orange and stayed there for a long time, eventually I had to pull the plug. Of course I had to manually go to download mode and launch Kies mini emergency recovery, the damn thing again got stuck at the orange screen.
If anybody has this experience do no proceed further and throw that damn thing back at At&T's face. Do not attempt to do anything. I made a mistake of then doing an ODIN one-click back to stop and the phone got stuck half way, went to the orange screen.. and then it was over.. The phone was dead, wouldn't turn on, no recovery or download mode with any button combo. When I plugged in to the wall, no battery indicator.
save yourself the trouble and return the damn thing
still there
I am a "noob" to posting here, and a noob to the android due to being an avid iPhone user. I am having the same problem, phone -!- computer and have tried every method i can find in this forum to get passed it. Are there any other thoughts or suggestions? (got hung at do not turn off target in odin) Thanks in advance to any help.
I would look at this thread http://forum.xda-developers.com/showthread.php?t=1153310
Stephenv1971 said:
I would look at this thread http://forum.xda-developers.com/showthread.php?t=1153310
Click to expand...
Click to collapse
went that route, still cant find dl mode. have resistors built and all. any way i try to boot shows me the phone -!- computer, and the computer doesnt attempt to recognise it so there is no communication between the computer and phone. unfortunately, i dont have a v/ohm meter, so i am not sure of the accuracy of the resistors i used to make my jig.
I fixed this many times with phone that had the button download mode and didn't.
Getting into download mode while softbricked like this wont show the normal download screen. IT will still show the error screen....
With download mode working still:
Simply remove the battery and replace,
Open odin
Hold down volume keys and plug it in till you see odin recognize ur phone.
Then continue to use odin.
Dosent work, repeat.
If you know ur button combo dosent work:
Just open odin.
Remove battery & replace.
Use jig (3k 100k ohms twisted)
Then when the phone turns on and your see the pc! screen plug in usb.
See if odin sees it.
Assuming your flash didn't fail on the PBL.bin or SBL.bin you should be fine.
Follow the methods suggested by other users here and you will get back up and running in no time at all.
Don't sweat the 'phone-!-pc' screen. I'm a little surprised that no one has given you the good news....that is just a version of the download screen for later hardware revisions. It looks bad, but if Odin recognizes your phone (if one of the COM fields goes active), just start your flash again.
Now if Odin does not recognize the phone when plugged in via USB, then you have some more work to do.
I had forgotten about posting here, and my problem has been resolved. So here it is... I tried everything that I could find within this forum, almost. I built my own jig with inferior radio shack components that would not activate download mode, though it would turn the phone on. I got wise, spent 8 dollars at ebay and purchased a JIG there. Instant download mode after 3 days (shipping). Reflashed with one click, updated w/ kies, made kernal changes and am now rockin my captivate. Thanks to those who assisted.
Steve_O_1971 said:
I had forgotten about posting here, and my problem has been resolved. So here it is... I tried everything that I could find within this forum, almost. I built my own jig with inferior radio shack components that would not activate download mode, though it would turn the phone on. I got wise, spent 8 dollars at ebay and purchased a JIG there. Instant download mode after 3 days (shipping). Reflashed with one click, updated w/ kies, made kernal changes and am now rockin my captivate. Thanks to those who assisted.
Click to expand...
Click to collapse
Using the 3-resistor method takes A LOT of patience, at least in my experience. Glad everything worked out.
beast534 said:
Using the 3-resistor method takes A LOT of patience, at least in my experience. Glad everything worked out.
Click to expand...
Click to collapse
Patience is a virtue, and my Ex's name. LOL! I can do without patience.
Jokes aside, i actually soldered the resistors to a plug that i had cut up, and made sure it was covered so my skin wouldnt come in contact. The Radio Shack here buys inferior products and sells them at reggular retail. Unfortunately my $300.00 V-Ohm meter is on the fritz, and i have not had the time or money to replace it yet, but I have intentions to check the actual resistance of the jig I made. ^^
I tried flashing the latest Cognition onto my captivate today using ClockworkMod but the phone appears to no longer start up. The phone just sits there acting like it has no power with a black screen. I've tried holding volume up & down while plugging in the USB cable. I've tried holding volume up & down while pressing the power button. I've even tried the 301k resistor usb plug. Are there any other methods I can try that I have missed while searching the forums?
Thanks in advanced!
captivater said:
I tried flashing the latest Cognition onto my captivate today using ClockworkMod but the phone appears to no longer start up. The phone just sits there acting like it has no power with a black screen. I've tried holding volume up & down while plugging in the USB cable. I've tried holding volume up & down while pressing the power button. I've even tried the 301k resistor usb plug. Are there any other methods I can try that I have missed while searching the forums?
Thanks in advanced!
Click to expand...
Click to collapse
Does your computer recognize your phone when you plug it in? If it does, try this
Open the one click root from your computer and click one click root if it should take you to clockworkmod recovery.
Sent from my T-Mobile G2 using XDA App
Change the usb port ?
Sent from my SAMSUNG-SGH-I897 using XDA App
I could never get the PC to recognize the device or even get anything to appear on the screen. Acts like it just doesn't have power. I think I'm going to try sending it to Samsung...
I doubt you are bricked. I had a similar issue where a ODIN flash failed midway through and I was left with a phone and black screen. There's a combination to get the phone directly into download mode which I tried. I THINK this is what it was:
Remove SIM, external SD card, and battery
Wait 10 seconds with battery out
Plug phone into computer (with battery out)
Hold Vol Up/Down + Power button
While holding the 3 buttons, insert battery
Release power button while holding Vol/Up down
Phone should be in Download mode
It took me a few tries to get the timing down, but it worked. The key combination might not be consistent with what others use. I think I've read somewhere that you don't need to hold the power button at all, I dunno. If you search, I know for sure there are more threads explaining the above method.
In regards to the 301k resistor, you might also want to try 300k or 302k. I know if you have problems finding these resistors, I've seen people hook up (3) 100k resistors in series from Radio Shack.
I also have a bunch of female USB plugs and resistors shipping to me on Monday. If you're still having problems by next week, send me a PM and I might be able to send you a jig to try out. If you send your phone into AT&T for warranty replacement, you MIGHT end up getting charged for the replacement. I've read stories of AT&T initially sending out a replacement phone, and then later billing the customer for the replacement since they were able to access system files and figure out the customer voided warranty by flashing a unsupported ROM.
I have been having trouble with my Bell Vibrant for the past few days, with a black screen after the 'S' Tried several things out there to resolve this issue, nothing seemed to work.
In desperation I tried the Odin3 one-click, not noticing its for the captivate. I successfully flashed and am now in a reboot loop with the AT&T logo screen. I can't get into recovery mode. or download mode to re flash with different ROM.
Any ideas????
Yes this is a vibrant device running a captivate rom and I have also posted this question in Vibrant general.
[email protected] said:
I have been having trouble with my Bell Vibrant for the past few days, with a black screen after the 'S' Tried several things out there to resolve this issue, nothing seemed to work.
In desperation I tried the Odin3 one-click, not noticing its for the captivate. I successfully flashed and am now in a reboot loop with the AT&T logo screen. I can't get into recovery mode. or download mode to re flash with different ROM.
Any ideas????
Yes this is a vibrant device running a captivate rom and I have also posted this question in Vibrant general.
Click to expand...
Click to collapse
Use odin for the vibrant, not familiar with that SGS phone so I don't know if they have a one click odin . If not, you will need the stock .tar or kernel, modem and zimage files.
Open Odin in windows.
Take out your extSD, Sim and battery, wait 10+ secs.
Now plug the usb in.
While holding the vol +- insert the battery and it should go into download mode.
Now you can click start in odin.
I do know that the vibrant is a pain in the ass to get into download mode and that the above is the most consistent way to get there.
This is what I know of the vibrant, correct me if I'm wrong anyone.
For what it's worth, I had a hard time getting my captivate into download mode. This is what I had to do...when you do this, have the ODIN for your phone ready because if you back out from download mode, you'll get the blessed 'phone to computer' screen...which I was still able to get into download mode from...but some people haven't had such luck.
1) Turn off phone...(take battery out or whatever)
2) Holding the two volume buttons down, SLOWLY plug in USB cord HALF-WAY. Push it in just a tad...if the screen doesn't come up with the shoveling android...push in just a little bit more...keep doing this until you get the shoveling android...if the phone turns on...you missed it - start over.
3) Once in download mode, if the ODIN program doesn't see your phone on a COM port yet...push the USB cord in the rest of the way and it should see it then. I think I actually had to unplug the cord and plug it back in slowly till it saw it. Once it does see it, don't touch the cord anymore!
4) Click start on ODIN and let it do it's thing. You should see a progress bar show up on your phone's download screen within a minute or so...if not...turn off the phone and try again. you will get the 'blessed' screen but hopefully you won't have to do it.
My heart stopped for a bit when I tried the above and it didn't work the first time and I got the 'blessed' screen. But I just tried again and all was fine...so don't fret too much.
Anyways...hope this helps.
iceman198 said:
For what it's worth, I had a hard time getting my captivate into download mode. This is what I had to do...when you do this, have the ODIN for your phone ready because if you back out from download mode, you'll get the blessed 'phone to computer' screen...which I was still able to get into download mode from...but some people haven't had such luck.
1) Turn off phone...(take battery out or whatever)
2) Holding the two volume buttons down, SLOWLY plug in USB cord HALF-WAY. Push it in just a tad...if the screen doesn't come up with the shoveling android...push in just a little bit more...keep doing this until you get the shoveling android...if the phone turns on...you missed it - start over.
3) Once in download mode, if the ODIN program doesn't see your phone on a COM port yet...push the USB cord in the rest of the way and it should see it then. I think I actually had to unplug the cord and plug it back in slowly till it saw it. Once it does see it, don't touch the cord anymore!
4) Click start on ODIN and let it do it's thing. You should see a progress bar show up on your phone's download screen within a minute or so...if not...turn off the phone and try again. you will get the 'blessed' screen but hopefully you won't have to do it.
My heart stopped for a bit when I tried the above and it didn't work the first time and I got the 'blessed' screen. But I just tried again and all was fine...so don't fret too much.
Anyways...hope this helps.
Click to expand...
Click to collapse
He is on a vibrant, not a captivate although it should be close to the same procedure. I've seen the usb half plug method but it never did anything for mine.
A jig should do the trick. Get a MicroUSB-b plug breakout board from sparkfun.com and two resistors (300k+1k) in serial across pins 4 and 5. Turn your phone off and take the battery, sim, and external sd card out. Pop the jig into the usb slot and put the battery back in. The phone should go into download mode on it's own without you having to hit any buttons.
After that, just follow what everyone else said - use a one-click-stock odin for your particular model.
The jig worked. took a trip to the source and grabbed the resisters and took apart the micro USB adapter included in my BlueAnt handsfree.
followed the directions from
http://forum.xda-developers.com/showthread.php?p=9804077#post9804077
Back in business.
Thanks all.
[email protected] said:
The jig worked. took a trip to the source and grabbed the resisters and took apart the micro USB adapter included in my BlueAnt handsfree.
followed the directions from
http://forum.xda-developers.com/showthread.php?p=9804077#post9804077
Back in business.
Thanks all.
Click to expand...
Click to collapse
Glad that worked and thanks for the update info.
Hey guys,
I got an infuse from a friend. When she gave it to me it was all stock and functional minus the fact that it would bootloop. When you would turn it on it would show samsung, turn off, samsung, turn off... About 3 seconds per on time. It would do this whenever it had the battery in or was plugged in. At first I was able to get it into download and then flash stock OEM. This fixed the problem, then I got into recovery and flashed a custom rom. All of this worked fine. Here's the problem
I tried restoring to the stock that I got the phone to before the custom rom was installed. This took 25 seconds and I knew something must have been wrong but I rebooted anyway. When rebooting I was faced with my original issues up above. Unfortunately its rebooting too quickly to put it into download mod. By the time I press the volume buttons and insert the usb it already boots and then starts over. If I do it quickly enough it goes to charge and bootloops to charge. The problem is that the phone bootloops whenever the battery is in. I don't have to press power for it to start.
Pretty frustrated and really would like some help. Thanks
EDIT: I ****ING FIXED IT!!! I swear this isn't a joke... I was reading a forum that had this problem and they all were saying they got angry and threw it/hit their phone and it booted up. Sitting there I eventually started entertaining the idea. I did a quick survey of the library I am in and... smacked it on my fist. THEN THE ****ING THING BOOTED UP!! What the hell!! SO excited. If it happens again, most efficient way is to drop the device on the top off the phone on a carpeted floor from about 2 feet
Faulty power button. Do a search.
Sent from my SGH-I997 using xda premium
Los maizak
psal217050 said:
Faulty power button. Do a search.
Sent from my SGH-I997 using xda premium
Click to expand...
Click to collapse
Am I looking for a replacement or what? Thanks for the speedy reply
psal may be on to something however it sounds like you are not trying download mode correctly - if you had the battery pulled and the usb disconnected it could not be rebooting.
Edit: If the power button is sticking, most likely no need to replace- here is a video of how to replace the screen, not what you are doing but the point is it shows how to take the phone apart so that you can clean the power button. Hope this helps : http://www.youtube.com/watch?v=1WS5I0SpL6c
Pony Express said:
psal may be on to something however it sounds like you are not trying download mode correctly - if you had the battery pulled and the usb disconnected it could no t be rebooting.
Click to expand...
Click to collapse
It reboots only when I put the battery in. So the moment I put the battery in to try and get it into recovery it starts booting immediately. It doesn't give me enough time to actually press volume up and down and then insert usb. If i do it fast enough it just boots to charging mode and boot loops to that instead of the samsung splash
Edit: I have already taken apart the phone. Not really sure what I should clean. It looks completely fine and acts similarly to the volume buttons. How would you recommend I clean it?
Pony Express said:
psal may be on to something however it sounds like you are not trying download mode correctly - if you had the battery pulled and the usb disconnected it could not be rebooting.
Edit: If the power button is sticking, most likely no need to replace- here is a video of how to replace the screen, not what you are doing but the point is it shows how to take the phone apart so that you can clean the power button. Hope this helps : http://www.youtube.com/watch?v=1WS5I0SpL6c
Click to expand...
Click to collapse
I am not so sure that this is a hardware issue. Why would the problem disappear when I flash the OEM but then return everytime I restore to the faulty stock. I already took apart and the power button seems pristine.
With this extra info, it is pointing more toward a sticking power button with a hardware issue still something to consider... have you tried pulling battery, install usb, hold both volume buttons (no power button) and while continuing to hold vol buttons insert the battery ?
Edit: If the issue is indeed in the faulty rom, delete it and use something different.
Pony Express said:
With this extra info, it is pointing more toward a sticking power button with a hardware issue still something to consider... have you tried pulling battery, install usb, hold both volume buttons (no power button) and while continuing to hold vol buttons insert the battery ?
Edit: If the issue is indeed in the faulty rom, delete it and use something different.
Click to expand...
Click to collapse
Not sure how I would delete the rom because I cannot boot the phone, boot to recovery, or boot to download. I did try having the usb in, holding volume and then putting in battery. It didn't work. Do you think a jig would work? Thanks
Yes, I think for such a small price it is worth a shot- best of luck !!
It would also be worth mentioning to be certain you have a good usb cable as well as a good usb port on the puter.
aeppacher said:
Hey guys,
I got an infuse from a friend. When she gave it to me it was all stock and functional minus the fact that it would bootloop. When you would turn it on it would show samsung, turn off, samsung, turn off... About 3 seconds per on time. It would do this whenever it had the battery in or was plugged in. At first I was able to get it into download and then flash stock OEM. This fixed the problem, then I got into recovery and flashed a custom rom. All of this worked fine. Here's the problem
I tried restoring to the stock that I got the phone to before the custom rom was installed. This took 25 seconds and I knew something must have been wrong but I rebooted anyway. When rebooting I was faced with my original issues up above. Unfortunately its rebooting too quickly to put it into download mod. By the time I press the volume buttons and insert the usb it already boots and then starts over. If I do it quickly enough it goes to charge and bootloops to charge. The problem is that the phone bootloops whenever the battery is in. I don't have to press power for it to start.
Pretty frustrated and really would like some help. Thanks
Click to expand...
Click to collapse
Use this to go to stock old version:
http://forum.xda-developers.com/showthread.php?t=1116251
Then open kies mini connect your phone on kies update and upgrade to the newest GB version.
At this point u are on a stock if u want root try this:
http://forum.xda-developers.com/showthread.php?t=1613523
Option C is the better
daemonlmrj said:
Use this to go to stock old version:
http://forum.xda-developers.com/showthread.php?t=1116251
Then open kies mini connect your phone on kies update and upgrade to the newest GB version.
At this point u are on a stock if u want root try this:
http://forum.xda-developers.com/showthread.php?t=1613523
Option C is the better
Click to expand...
Click to collapse
I can't do this because in order to go to download mode the phone needs to be off. The moment I insert the battery it automatically starts bootlooping
Pony and psal are prolly right. Try fixing your power button.