[Q] My screen is dim and flickering? - HTC Sensation

When I turned on my Sensation 4g after applying a wet apply screen protector, the screen was extremely dim and flickered. Could I have damaged my phone by putting on a screen protector? I had the phone off when I applied it and waited hours for it to dry. I pulled the battery and covered my phone in rice hoping no permanent damage was done. Also, I've noticed that when the battery was in, the black screen was not really black. The backlight dimly shined through.

nartdensin said:
When I turned on my Sensation 4g after applying a wet apply screen protector, the screen was extremely dim and flickered. Could I have damaged my phone by putting on a screen protector? I had the phone off when I applied it and waited hours for it to dry. I pulled the battery and covered my phone in rice hoping no permanent damage was done. Also, I've noticed that when the battery was in, the black screen was not really black. The backlight dimly shined through.
Click to expand...
Click to collapse
1.Turn off Auto-backlight, the screen protector may cover the sensor on phone
2.If that doesn't work, remove protector and see what happens
But you mentioned it was wet-the Sensation can easily get dust under the screen since the screen isn't fused w/ edges...I think some water got under the screen? If this is so you need to contact your provider for a warranty exchange.

I have S-OFF and I'm running ARHD. Will it be possible for me to contact my provider for an exchange? Do they check for those? It seems to have gotten worse. The liquid must have seeped in deeper into the phone.
Edit: After booting into the bootloader and deleting files, the screen seems to have cleared up. There are only a few water spots now and only visible on a white screen.

sorry to dig up an old post, but im curious.. did you end up replacing some parts? if so which parts?

Related

LCD Screen Seal Issue

Just a word of warning...and I know this was prevalent with the Evo and a few other HTCs.
I carefully went to apply a high-er quality screen protector, and used a very small amount of water/soap mixture to set it properly. When I squeegeed the water out, almost all of it went directly through the screen where the earpiece is. It then proceeded to get trapped between the actual LCD panel and the glass screen. It seeped all the way down the screen.
After researching, I put the phone in a bowl of dry rice and put a heat lamp over it. The water dried out, but it left a large wavy line along where the edge of the water stopped. Brought it to sprint and they ended up swapping it out for me, but just wanted to give a heads up.
klecka27 said:
Just a word of warning...and I know this was prevalent with the Evo and a few other HTCs.
I carefully went to apply a high-er quality screen protector, and used a very small amount of water/soap mixture to set it properly. When I squeegeed the water out, almost all of it went directly through the screen where the earpiece is. It then proceeded to get trapped between the actual LCD panel and the glass screen. It seeped all the way down the screen.
After researching, I put the phone in a bowl of dry rice and put a heat lamp over it. The water dried out, but it left a large wavy line along where the edge of the water stopped. Brought it to sprint and they ended up swapping it out for me, but just wanted to give a heads up.
Click to expand...
Click to collapse
Thanks for the heads up! I ordered a screen protector and was going to apply it the same exact way.

[Q] Water under screen - Am I screwed?

So here's the situation:
I was applying a screen protector from bestskinsever (huge fan of their stuff). You need to apply a small amount of soapy water to correctly apply the film. I finished applying it evenly and then turned my phone on, only to find (to my horror) that there was what appeared to be moisture under the screen, which made the screen look terrible when the backlight shone through it.
I immediately turned the phone back off, pulled the battery, and stuck the phone into a plastic bag full of rice (a solution I had heard of at some point). My hope is that the water will eventually evaporate and be soaked up by the rice, returning my phone to it's previous state of awesomeness.
What do you think the chances are of that? None of the water sensors on the phone or the battery were tripped by the water, but the screen looks pretty ugly as of last night.
Anyone else have to deal with this? Did I do everything right once discovering the issue?
Thoughts welcome.
Blocker85 said:
So here's the situation:
I was applying a screen protector from bestskinsever (huge fan of their stuff). You need to apply a small amount of soapy water to correctly apply the film. I finished applying it evenly and then turned my phone on, only to find (to my horror) that there was what appeared to be moisture under the screen, which made the screen look terrible when the backlight shone through it.
I immediately turned the phone back off, pulled the battery, and stuck the phone into a plastic bag full of rice (a solution I had heard of at some point). My hope is that the water will eventually evaporate and be soaked up by the rice, returning my phone to it's previous state of awesomeness.
What do you think the chances are of that? None of the water sensors on the phone or the battery were tripped by the water, but the screen looks pretty ugly as of last night.
Anyone else have to deal with this? Did I do everything right once discovering the issue?
Thoughts welcome.
Click to expand...
Click to collapse
I had this happen with my mytouch 4g. I applied a skinomi protector and when I turned on the screen I noticed the moisture under the screen and it made the screen look discolored. It did get a lot better after a few days but it still had a water stain on the LCD.
Sent from my HTC Sensation 4G using XDA App
Don't think your standing a good chance. Are you sure the water is underneath the screen and not between the protector and the screen? If I were you, I'd remove the backcover. That frees the device's sides so the water might run out there. You might also try to suck it out with a strong vacuum cleaner Just be careful not to scratch your Sensation.
I strongly suggest you NOT to use vacuum cleaner because it may cause damage to delicate hardware of the phone. Because Vacuum cleaner creates static electricity.
As for the water are you sure it is under the screen not between protector and screen?
If i were you i would considering removing screen protector. If it is still there it means it is under scteen and since you cannot disassemble lcd screen i would remove back cover and pray for it to be evaporate.
Hope this help
whole reason why I stay away from water solution application based SPs.
they may stick better and all but the risk...
someone needs to come up with a better solution for these "military grade" SPs.
op, sorry to hear about your phone. I hope it fixes it self. if not, hope you have insurance. (I know it would suck shelling out another $130 for the deductible when you just bought the phone but...)
sert89 said:
I strongly suggest you NOT to use vacuum cleaner because it may cause damage to delicate hardware of the phone. Because Vacuum cleaner creates static electricity.
Click to expand...
Click to collapse
Are you sure? Never heard of that...
yes dude i don't mean to offend you if i did then sorry but once i used to clean my computer from dust with a vacuum cleaner or a hair dryer. Hair dryer is much worse but vacuum cleaner is no good either.
sert89 said:
yes dude i don't mean to offend you if i did then sorry but once i used to clean my computer from dust with a vacuum cleaner or a hair dryer. Hair dryer is much worse but vacuum cleaner is no good either.
Click to expand...
Click to collapse
You certainly did not offend me, that's okay, I was just wondering whether it was just a statement with no real knowledge behind it or if it was for real, because I have never heard of such a thing. I may or may not be stupid
BTW, I have also cleaned my computer with both a vacuum cleaner and a hairdryer (with cold air of course) and didn't have any problems.
did u get ur phone get rid of the water with the rice and how long it takes i have same issue here.
Blocker85 said:
So here's the situation:
I was applying a screen protector from bestskinsever (huge fan of their stuff). You need to apply a small amount of soapy water to correctly apply the film. I finished applying it evenly and then turned my phone on, only to find (to my horror) that there was what appeared to be moisture under the screen, which made the screen look terrible when the backlight shone through it.
I immediately turned the phone back off, pulled the battery, and stuck the phone into a plastic bag full of rice (a solution I had heard of at some point). My hope is that the water will eventually evaporate and be soaked up by the rice, returning my phone to it's previous state of awesomeness.
What do you think the chances are of that? None of the water sensors on the phone or the battery were tripped by the water, but the screen looks pretty ugly as of last night.
Anyone else have to deal with this? Did I do everything right once discovering the issue?
Thoughts welcome.
Click to expand...
Click to collapse
This happened to me and it disappeared in about 8 hours I was freaking out till it worked well then my touch screen started to not detect my fingers so I hit up tmobile telling them my touch screen screwed up and they sent me another one for 5
Bucks.
Sent from my HTC Sensation 4G using XDA App
If it is screwed the descent original screens are not cheap, the cheap ones on ebay are terrible...
HTC wont replace due to non manufacturing damage...
hopefully your phone has a catastrophic mboard failure and they replace it for another reason
looks like i may have gotten some water under my screen as well. i'm seeing "let it evaporate" as the only solution and "pray it doesnt stain your LCD".. what if it does stain my LCD? is there any repair solution? anyone have a link to a good training video?

Light bleed and red dot on screen

I dropped my phone, It fell out of my pocket in the gym today.
Now there is a red spot visible on the middle right screen link. I also noticed some light bleed from the left side. Can I fix this myself somehow?
I find it weird because the screen glass is in good condition, could the screen itself be permanently damaged?
It's pity as I still love this phone, and now it's damaged..
Thanks in advance
Yes, the top glass could be perfectly intact while screen beneath is damaged. I have seen this many times on Samsung phones that have been dropped.
Can't really either screen issue unless you replace the LCD.

Screen won't turn on, thus stays black during call.

Hey, when i receive and accept a call, my screen immediately turns off. Like it should when i put my ear up to it. But during the call i cant do anything to get the screen to turn on. After the call i have to press the lock button and unlock it again to get it on.
1) bootloader unlocked
2) custom kernel?
3) stock ROM?
4) rooted?
6) What version of the OS are you on? MM 6.0.1 / .511
7) This is recent, tried with 2 different roms so it isnt rom reliant i guess.
8) When in service menu and testing the light sensor it responds on my hand covering the sensor so i don't think its faulty.
J03llV said:
Hey, when i receive and accept a call, my screen immediately turns off. Like it should when i put my ear up to it. But during the call i cant do anything to get the screen to turn on. After the call i have to press the lock button and unlock it again to get it on.
1) bootloader unlocked
2) custom kernel?
3) stock ROM?
4) rooted?
6) What version of the OS are you on? MM 6.0.1 / .511
7) This is recent, tried with 2 different roms so it isnt rom reliant i guess.
8) When in service menu and testing the light sensor it responds on my hand covering the sensor so i don't think its faulty.
Click to expand...
Click to collapse
Clean your screen protector, if you have plastic protector REMOVE the screen protector.
Flash FTF with all WIPE options selected..
sceryavuz said:
Clean your screen protector, if you have plastic protector REMOVE the screen protector.
Flash FTF with all WIPE options selected..
Click to expand...
Click to collapse
I have tempered glass with a cutout for the sensor though..
J03llV said:
I have tempered glass with a cutout for the sensor though..
Click to expand...
Click to collapse
Mostly, screen protector cause that. Second sensors might be broken. Software is the last thing (if comes with stock)..
Go to *#*#7378423#*#* service test and go to proximity sensor, if it stays "ON" something is wrong with the proximity sensor, if you are absolutely 100% sure nothing is blocking your sensor, have you ever changed your display assembly? try pressing down around the top right of screen with a little force, both front and back if it switched to "OFF" when you press your screen there's a slight gap between your motherboard and front glass.
webslasher said:
Go to *#*#7378423#*#* service test and go to proximity sensor, if it stays "ON" something is wrong with the proximity sensor, if you are absolutely 100% sure nothing is blocking your sensor, have you ever changed your display assembly? try pressing down around the top right of screen with a little force, both front and back if it switched to "OFF" when you press your screen there's a slight gap between your motherboard and front glass.
Click to expand...
Click to collapse
Holy this is it. I had to get my front glass replaced because it was shattered, when i press the screen it turns off, when i block the sensor it goes back to on again until i press on the screen. Also my vibrator motor seems to not function properly since, it sometimes doesnt vibrate at all, and sometimes with very little feedback. Could this also be a result of the replacement?
J03llV said:
Holy this is it. I had to get my front glass replaced because it was shattered, when i press the screen it turns off, when i block the sensor it goes back to on again until i press on the screen. Also my vibrator motor seems to not function properly since, it sometimes doesnt vibrate at all, and sometimes with very little feedback. Could this also be a result of the replacement?
Click to expand...
Click to collapse
It could be the glue is not settling in correctly and adds very little gap than original one, did you replace the screen yourself? Mine showed this behavior I then reheat the edges of the screen with hair dryer then put pressure around the screen with those black paper clips, reheat it again then let it cool for about 2 hours.
I'm not entirely sure about the vibrator motor
webslasher said:
It could be the glue is not settling in correctly and adds very little gap than original one, did you replace the screen yourself? Mine showed this behavior I then reheat the edges of the screen with hair dryer then put pressure around the screen with those black paper clips, reheat it again then let it cool for about 2 hours.
I'm not entirely sure about the vibrator motor
Click to expand...
Click to collapse
No, I had it done by a company in phone repairs. But i kinda regret fixing it instead of buying a new phone tbh..
J03llV said:
No, I had it done by a company in phone repairs. But i kinda regret fixing it instead of buying a new phone tbh..
Click to expand...
Click to collapse
I bought this phone second hand and it had this issue, What I did was hair dryer and paperclip. and ..... try a more ghetto solution, which involves opening the back door, put some foam and double tape it near the camera module, there's an empty space. Make sure it presses the motherboard but not too hard or it will compromise the waterproof glue holding the back cover.
I took a picture of what I did to fix my issue
http://imgur.com/a/5bwuN
webslasher said:
I bought this phone second hand and it had this issue, What I did was hair dryer and paperclip. and ..... try a more ghetto solution, which involves opening the back door, put some foam and double tape it near the camera module, there's an empty space. Make sure it presses the motherboard but not too hard or it will compromise the waterproof glue holding the back cover.
I took a picture of what I did to fix my issue
http://imgur.com/a/5bwuN
Click to expand...
Click to collapse
I'm not going to try that lol, i'm sure I will **** it up big time.. Im going to email the company trying to get something happen..
I had that issue, but since I run custom ROM such as SlimX no more black screen don't know why ?
Just for info is someone has this problem, i had small skin flake on the sensor hahahha.

can anyone tell me whats inside my display ?water or screen peeling off ?

Since last week I was noticing bubble /color peeling off from inside near left top on my screen, I ignored in the beginning, I had tempered glass installed that's why I didn't notice much , but I removed tempered glass to see what happened and it seems weird. Attaching images please tell me if anyone can figure out why this happened and if I need to worry for display.
* it's from inside, not outside.
My screen started to peel off. Mine is below the home button and is getting worse i just dont have the time and money to replace the screen. But it sucks. See video below its the same as that.
https://youtu.be/Qw7hQ6FruIM

Categories

Resources