Hello everyone. This is my first post, so please be gentle. I've been reading around and I can't seem to find specific answers to my questions so I figured it would be best to make a post. This is my first Android phone and also the first phone I have rooted so I'm trying to be extra careful. I've already received tons of help from other threads in these forums, but as I said I've still got a few questions.
I rooted my SGS4G using SuperOneClick v2.1.1, then proceeded to install CWM ROM Manager as per the instructions I found in many articles online. Once I got that installed I was unable to make backups as it would boot me into the stock recovery menu, which led me here searching for answers. That is when I came across this thread: [RECOVERY]CWM FINAL for the SGS4G After following the instructions I wasn't exactly sure what to do, so I attempted to boot into the "new" recovery menu which ended at an infinite boot logo, which I assumed was a soft brick after reading around a bit.
After thoroughly freaking out about my phone being bricked I looked around a bit more and came across this thread: [GUIDE] Noobs guide to Odin to flash your SGS4G (Windows) Following that thread I was able to install the T959VUVKB5 Stock + Root ROM which restored my soft brick. Once that was installed I installed CWM ROM Manager again thinking the Recovery Menu would be fixed and I could finally make a backup before moving on, but it wasn't. Then I came across this thread: [Odin][Kernel] drhonk's Bali 3.3 for Froyo, Installs CWM!
After installing drhonk's Bali 3.3 for Froyo kernel I was finally able to make a single nandroid backup (and backup my apps using Titanium Backup)! I messed around on the phone for a few days with no issues (other than the Android flickering in the boot logo). Now I am ready to move on to trying out a few ROMS. So, first thing first I said: I need to make another backup. So I entered the Recovery Menu via the CWM ROM Manager and attempted to make another backup, and this is what I get:
E: failed to open /etc..... (I couldn't write fast enough to copy the entire message)
E: unknown volume for path [/sdcard] (10s)
The second of which repeated over and over until it reached 0s and then my phone was rebooted.
TL;DR
- Rooted using SuperOneClick
- Installed ROM Manager and couldn't make a nandroid backup correctly
- Attempted to install CWM FINAL for the SGS4G, which resulted in a soft brick
- Restored using ODIN and installed T959VUVKB5 Stock + Root ROM and drhonk's Bali 3.3 for Froyo kernel
- Cannot make nandroid backups (other than the initial one apparently), Recovery Menu does not seem to be working correctly
- I am not comfortable trying new ROMs until I am able to make backups correctly
Anyway, so here are my questions:
1. What do I need to install to allow me to make nandroid backups correctly? Or is there another app besides CWM ROM Manager that will allow me to do this?
2. I would like to try a few other ROMs, but I when I reach the so-called "Do the mounting stuff" step I am unable to continue as my Recovery Menu isn't working correctly. What do I need to install in order to be able to do complete this step? I have a feeling the answer to #1 will solve #2 as well.
3. I would like to try a few of the GB ROMs (such as Valhalla v1.3.2 or Stock Gingerbread 2.3.3 Deodexed + Root), but I am not sure exactly where to go from here. Is the GB Ext4 Starter Pack the way I need to go, or would this way be better? Can I do either of these without a working Recovery Menu?
Thanks in advance for all the help!
Your first mistake was rom manager. It does not work for this phone correctly. Odin one of Dr honks kernels to get cwm recovery. They are in the dev section.
Sent from my SGH-T959V using xda premium
im not sure how many times this has been posted (i think i say this once a day....) but rom manager DOES NOT WORK ON THIS PHONE.
it is fine. if you can wait a day or two, i will make a nice noob guide on getting from stock to a custom rom. i will be sure to link every pertinent thread and be sure to have a little FAQ section. hopefully it will help you.
Exodian said:
Your first mistake was rom manager. It does not work for this phone correctly. Odin one of Dr honks kernels to get cwm recovery. They are in the dev section.
Click to expand...
Click to collapse
As I said in the post, I've already installed drhonk's Bali 3.3 for froyo kernel.
jager555 said:
im not sure how many times this has been posted (i think i say this once a day....) but rom manager DOES NOT WORK ON THIS PHONE.
it is fine. if you can wait a day or two, i will make a nice noob guide on getting from stock to a custom rom. i will be sure to link every pertinent thread and be sure to have a little FAQ section. hopefully it will help you.
Click to expand...
Click to collapse
Thanks, but I figured that out shortly after installing it. What alternative are we supposed to use? Hopefully your noob guide will help.
are you sure you understand? seeing as you mentioned BOTH bali and krylon's cwm, yet you still do not know how to get the custom recovery on the phone. once again, i will write a nice guide for you, so for now, just odin back to stock and give me a day or two. once im out of work, i will take a nap and write this for you.
jager555 said:
are you sure you understand? seeing as you mentioned BOTH bali and krylon's cwm, yet you still do not know how to get the custom recovery on the phone. once again, i will write a nice guide for you, so for now, just odin back to stock and give me a day or two. once im out of work, i will take a nap and write this for you.
Click to expand...
Click to collapse
Apparently I do not understand. I guess I will just wait for your guide. Hopefully it will pick up where the other guides failed (for me anyway).
Edit: After reading around a bit I think I understand where I went wrong. As a noob I was confusing CWM with ROM Manager (after all, they're both made by the same people right? I believe that's what was confusing me ). I have since uninstalled ROM Manager and have booted to the Recovery Menu and successfully made a backup.
I myself have been a member for coming up on one year. And when I originally joined I was modding my Mytouch 3G. Much easier phone to mod and especially with ROM manager. This phone on the other hand requires more attention to detail. It is very important to do your due diligence to research this site for answers before posting. The reason is, all the wonderful and talented folks making all this possible are providing us all these great hacks, cracks, and roms for free. The information is here if you just look for it. Now if you are having trouble understanding the info that is also understandable. I find questions are better received if you show everyone what you have researched and then say what your are confused about.
Enough of the lecture, the end result is that everyone here is really nice and helpful. Here are the 3 links you should save. The Bible lists everything about our phone. Now at this stage in the game unless you really want to get more background on how the phone has evolved from Froyo to GB you won't need to read the Bible. The first thing you will need to do is follow the instructions for Bali 3.3 + CWM. This will provide you with the Red CWM recovery making it possible for you to flash Froyo Roms. Once you have completed this step you can move on to the GB Starter Pack. This guide will prepare your phone with the correct bootloaders it requires to run GB Roms. Once this process has been completed you can flash GB Roms. And if you need a quick list of the roms available just look in the Bible. Hope this helps, just be patient and make sure you understand what you are reading and attempting before doing anything. And if you don't understand a step or a process then come and ask and you'll get better answers and better understanding of what you're actually doing to your phone.
SGS4G Bible
http://forum.xda-developers.com/showthread.php?t=1117554
Bali 3.3 + CWM
http://forum.xda-developers.com/showthread.php?t=1195860
GB Starter Pack
http://forum.xda-developers.com/showthread.php?t=1223765
Thanks for the help. I tried to do as much research as I could before posting (as you can see, I've posted two of the three links you suggested in my OP, and I basically keep the Bible open at all times ). It's just the little things that I find confusing, which is why I posted this thread. It's nice to know that from this point I can proceed to the GB Starter Pack and play around with the GB ROMs, but I think I'd like to try a few Froyo ROMs before I take that step Thanks for confirming that!
Sorry for the double post but I have another question.....
I've been reading over FB's GB Ext4 Starter Pack thread and I just wanted to make sure that once you get to the part where you flash your "favorite GB rom" that Valhalla v1.3.2 would be an acceptable ROM to flash there. If not, which ROM should I flash first, then flash Valhalla? Thanks in advance.
Yes, Valhalla would be fine to flash at that point (any version). just as long as you went through each step of the directions first. you'll be fine.
Related
Ok, I've got to ask this, even though I know it could probably be pieced together with just the right posts from the forum here. But I've got several mental issues, one of those being comprehending at times, and also I have a bad problem with wording sometimes. So if I can't find all the information I need in a single place (maybe two lol), then the chances of me screwing something up are immensely increased. So please just bear with me, and lemme see if I can spit this out as simply as possible.
I've just rooted my USCC Mesmerize with SuperOneClick, so now I need to know some things. Forgive me if they seem out of order at all, but just gonna ask as they come to my mind.
I wanted to install the Voodoo kernel. Do I have to flash a custom ROM before I can do this, or can I do it just by rooting the phone and having all the OEM software untouched?
I'm pretty sure that no matter what I choose to do next, that I first need to do a full back-up of my phone in case of error. I saw the post mentioning the install of Titanium Backup and then ROM Manager. Before I go and install anything, I just wanna make sure that it IS one of those 2 apps that I'm supposed to use to make that initial back-up. And if not, what app would it be?
I know that CWM has to be installed sometime also. Also in the same post I mentioned above, the OP stated "In ROM Manager I did "Flash ClockworkMod Recovery" and chose the Fascinate option and was told that it downloaded the latest ClockworkMod Recovery.". So what I now need to clarify is this. Does ROM Manager just download the newest ClockworkMod Recovery files and then I have to install them manually via the forum sticky, or does it download AND install them completely for me?
And I've seen/heard a lot all night as I've been researching about Nandroid back-ups. But am unclear at this point as to which app is responsible for making those. Not sure if it's one I've already mentioned above, or a totally different one I may have missed. So help there would also be much appreciated.
At this moment, I think those are all the questions I really need a little more clarity on. Other than that, I think I can handle it by myself for the time being. And thank you again for bearing with me as I learn my way around a little bit more. I chose this forum out of all the others I stumbled across last night due to the level of professionalism I've seen so far here. I just wish the other Dev forum I've been a member of for a long time had the same level of professionalism that I've seen here so far lol.
lets try this again...
1. first thing you need to do is flash cwm on your phone...follow the directions on the page...link : http://forum.xda-developers.com/showthread.php?t=850898
2. figure out what Rom you wanna flash...link : http://forum.xda-developers.com/forumdisplay.php?f=890
3. finally...flash the voodoo kernel onto your phone and make sure to get the one for the mesmerize...link : http://forum.xda-developers.com/showthread.php?t=871915
4. as far as backing up you can use titanium or flash your mesmerize back to stock...link : http://forum.xda-developers.com/showthread.php?t=881064
all this worked well for me and i hope it works just as well or better for you!
I hate to say this, but you confused the hell out of me and I've written a lot of how-to's on every one of these subjects.
Sent from my SCH-I500 using XDA App
1. Install RomManager from the marketplace. Then, in RomManager, install ClockworkMod Reocvery. However, you need to follow the steps in the CWM thread to get it to work correctly.
2. After you have clockworkmod recovery working, do a Nandroid backup. You can do this from RomManager and should. Titanium backups are for apps and such.
3. After you backup immediately flash the Voodoo kernel for the Mesmerize with Voodoo Sound. It's great! But more importantly, it flashes a 'permanent' recovery onto your phone so you can boot straight into a functional recovery and not have to use ODIN.
4. Find ROMs you like and install them. Make sure you always wipe your data before a ROM flash. When you want to go back to your stock ROM, just restore your backup from the recovery.
Note, after you install the Voodoo kernel it will take a while to boot because it is converting your phone's filesystem. Once you have Voodoo enabled you should not flash another kernel unless you turn off the Voodoo lagfix. This can be done in recovery menu it provides.
I have been searching through the forums and have been able to find answers to a few of my questions. However I have been away so long and previous phone MT3G was so much easier to work with than the SGS4G I'm a little lost on some of the jargon.
I managed to get the amazing Bionix frost rom installed and working. Here is my question.
I was able to get CWM on my phone to flash the rom, now when I boot to recovery I am getting the stock recovery screen but if I select reinstall packages I get the CWM Recovery v3.0.2.8. On my MT3G when I booted into recovery the CWM screen was the first thing I saw, I just want to confirm that this is the normal and or correct method to access CWM on my SG4G.
thanks in advance for your responses.
flash dr honks kernel. that will make sure everything is correct with CWM. that should fix any issues you are having. If you have any questions let me know. Its not too bad. I think its easier using ODIN but you can do it either way.
That is the normal process for bionix. It uses an older cwm stock. Search for the Bali 3.3UV kernel. Once you flash that, you will go straight to cwm. plus other stuff. Read his op. Once you undervolt on frost...omg. That battery life is out of control
Sent from my SGH-T959V using xda premium
Click on the Bali + CWM link in my signature. You might as well start learning how to use Odin.
Glad to know you started some reading on your own! FBis251's Odin Bali 3.3 makes flashing Froyo so much easier.
Here's five of the most valuable things I've learned so far:
1) Odin is your friend.
2) Losing your soft brick virginity isn't a bad thing. QQ if it's a hard brick though. Nothing in this forum would really give you a hard brick though.
3) The Bible is quite holy. Don't read it and you'll get some sort of punishment from the community.
4) Reading is fundamental.
5) The developers are awesome!
Not in any specific order. XD
You should try out the GB ROMs here once you get more comfortable flashing on this phone. They're crazy smooth.
Thanks all.
I have been going through the "Bible" each visit to the site. That's where I was able to figure out how to get the Bionix Frost rom working on my phone. And because I missed a few steps like making sure the permissions were correct before flashing I experienced my first soft brick. Which took another 3hrs of reading and playing with Odin to get fixed. But that's what I love about this site. Everyone is so knowledgeable and willing to help. It was't to hard to find out where I messed up and how to fix it. I appreciate all the help, I will start with FB's Bali+CWM upgrade and then I'm hoping to flash Valhalla. The rom looks amazing.
FBis251 said:
Click on the Bali + CWM link in my signature. You might as well start learning how to use Odin.
Click to expand...
Click to collapse
Thanks again FB, just followed your guide and now am enjoying the red CWM. Quick question, with this setup I can now flash any FROYO roms directly from CWM correct? The GB roms however like Valhalla will require the GB bootloaders.
Locobato said:
Thanks again FB, just followed your guide and now am enjoying the red CWM. Quick question, with this setup I can now flash any FROYO roms directly from CWM correct? The GB roms however like Valhalla will require the GB bootloaders.
Click to expand...
Click to collapse
That's correct.
First off, Thanks to everyone for the posts and for future patience.
I know there has been a lot of discussion on this subject, but I seem to have elevated it to a new level of loopy. Bear with me, please; I'll make whatever changes needed. I have researched/read a lot tried many of the recommended procedures and frankly, I think it has all become mud stew in my head. My wife is none too happy, and if you guys could help me save my genitals/marriage, I'd be much appreciative.
The facts: 1 T-Mobile SGS4G t959v, 1 Mac os X 10.6.8, 1 Heimdall 1.3.1 and 1 ticked-off wife.
So, following the xda forum, I successfully rooted the device. Then I downloaded ROM manager and installed CwM (now I realize the error of my ways), downloaded and flashed Bionix. Phone looped "3e" recovery.
After much research, found heimdall on XDA, and was able to get the recovery image changed to CwM Voodoo Lagfix Recovery v3.0.2.8x. Now, I'm looping that recovery. Tried the bali 3.3 kernel, flashed just fine. found sgs4g official gb2.3.6....Rom, flashed just fine. Still, I remain at the red voodoo screen.
Obviously, I can access the sd card through my mac, and have tried various update.zip procedures, and various ROMs.
So, I've been reading for several days now, poring over these and other forums, and if I understand it correctly, bali3.3_heimdall.tar.gz (thank you very much!) is supposed to undo the ROM manager screw up from earlier (and I can only think that I am missing some critical info here), but no, still looking at the voodoo recovery.
I AM kind of new to this, however I have rooted and modded 4- MyTough 3g's and a defy, All running CMx.
Thanks again,
SN
Try disabling voodoo lag fix and see if that helps
Sent from my HTC_Amaze_4G using xda premium
Thanks again,
it's done, with no change.
You are aware that Bali3.3 is a Froyo kernel? If the last rom you flashed was GB 2.3.6 then try flashing a GB kernel and make sure your mounts are correct.
missed the bali/froyo. does this imply that I might flash a froyo rom over bali? or do I need to flash a gb kernel for the 2.3.6 rom? Also, I'm using heimdall and I don't know how to use non-.tar files with it; or if you can.
supernugget said:
missed the bali/froyo. does this imply that I might flash a froyo rom over bali? or do I need to flash a gb kernel for the 2.3.6 rom? Also, I'm using heimdall and I don't know how to use non-.tar files with it; or if you can.
Click to expand...
Click to collapse
:facepalm:
There are line-by-line instructions all over this forum to install kernels and custom roms.
The search button is your best friend here. Use it! Google can also search the xda forum... try starting your search with: site:forum.xda-developers.com
For example:
Code:
site:forum.xda-developers.com Galaxy S 4G Heimdall
or
Code:
site:forum.xda-developers.com galaxy s 4g download mode
Learning to use XDA will help you find what you need. Following the rules will help you get answers.
I say all this, because every problem you are having is already answered in this forum!
Please use the Q&A Forum for questions Thanks
Moving to Q&A
Hello there guy's I'm new with rooted charge phones. Well guy's last night I did a stupid thing with my phone.. I accidentally updates my phone with the new OTA FP1 with rooted rom. Well guy's now my phone is screwing up.
So I followed few steps on at XDA.. How to fix my phone.. So I got my phone on stock rom and also I got the new update OTA FP1.
Well guy's I need some help on rooting this phone with the new update stock OTA FP1 rom.
The person who help me on rooting my phones he left to a church mission at south Africa.
Could any one please guide me on steps on rooting this phone on the new stock Rom (FP1) rooted also includes radios, kernel.
Please I need help guides steps with this phone issues because I'm not great person on rooting.
Sent from my SCH-I510 using xda premium
sgtkillspot said:
Hello there guy's I'm new with rooted charge phones. Well guy's last night I did a stupid thing with my phone.. I accidentally updates my phone with the new OTA FP1 with rooted rom. Well guy's now my phone is screwing up.
So I followed few steps on at XDA.. How to fix my phone.. So I got my phone on stock rom and also I got the new update OTA FP1.
Well guy's I need some help on rooting this phone with the new update stock OTA FP1 rom.
The person who help me on rooting my phones he left to a church mission at south Africa.
Could any one please guide me on steps on rooting this phone on the new stock Rom (FP1) rooted also includes radios, kernel.
Please I need help guides steps with this phone issues because I'm not great person on rooting.
Sent from my SCH-I510 using xda premium
Click to expand...
Click to collapse
Follow direction #5:
http://forum.xda-developers.com/showthread.php?t=1560117
re
I was fuclking frustrated when trying to CWM / ROOT / CUSTOM rom my charge.
I have rooted and installed more roms than i can shake a stick at with my other phones.
But the lack of information on sooooo many of the dev threads that leave out soooooooooooooooooooooooo much info made my head spin.
First of all.
Odin is a program that you can install clockword mod with, as well as some custom roms.
Clockwork mod is a recovery / install tool that you install to be able to install custom roms and packages.
Even installing clockwork mod is a hassle, often you have to install it with odin and select, dont auto reboot. then pull the usb and then the battery.. then you have to hit the VolumeUp button + power + home to get into cwm.. and hopefully it will stick..
Once you get cwm installed you have to download a rom..
There are many of them, i went with a package that you load via odin instead of installing from clockwork mod.
i went with a package that was a stock 2.3.6 with root.
after i installed it, it was recommended that you wipe devlink cache, system cache.
finally after i rebooted i finally had a rom that was rooted.
This was after 2+ hours of searching through threads, downloading way too much crap and swearing at my computer for the lack of quality directions.
Usually XDA is rife with STICKYS that are easy to follow.
The charge forum is quite the opposite.
If i was not tired / drunk and frustrated i would post a correct HOW TO thread.. that i would imagine would not get stickied.
sprintrjm said:
I was fuclking frustrated when trying to CWM / ROOT / CUSTOM rom my charge.
I have rooted and installed more roms than i can shake a stick at with my other phones.
But the lack of information on sooooo many of the dev threads that leave out soooooooooooooooooooooooo much info made my head spin.
First of all.
Odin is a program that you can install clockword mod with, as well as some custom roms.
Clockwork mod is a recovery / install tool that you install to be able to install custom roms and packages.
Even installing clockwork mod is a hassle, often you have to install it with odin and select, dont auto reboot. then pull the usb and then the battery.. then you have to hit the VolumeUp button + power + home to get into cwm.. and hopefully it will stick..
Once you get cwm installed you have to download a rom..
There are many of them, i went with a package that you load via odin instead of installing from clockwork mod.
i went with a package that was a stock 2.3.6 with root.
after i installed it, it was recommended that you wipe devlink cache, system cache.
finally after i rebooted i finally had a rom that was rooted.
This was after 2+ hours of searching through threads, downloading way too much crap and swearing at my computer for the lack of quality directions.
Usually XDA is rife with STICKYS that are easy to follow.
The charge forum is quite the opposite.
If i was not tired / drunk and frustrated i would post a correct HOW TO thread.. that i would imagine would not get stickied.
Click to expand...
Click to collapse
Hey bro, no need to get frustrated, you tried too hard to learn all at once. Let talk about what you have on your phone and what you want to achieve? I will take you through step by step.
Another thing I want to clear with you about Odin and CWM. They both are two useful tools to flash rom/kernel etc.. If kernel or full rom image are created in a ZIP format or extension, you use cwm. If a rom/kernel created in a MD5 format or extension, you would use Odin.
For example; the new FP1 kernel was made in both format so you have a choice to use either to flash.
Summary:
1. If the file ended with ZIP extension like "FP1_kernel.ZIP", you would use CWM to flash.
2. If the file ended with MD5 extension like "FP1_kernel.MD5", then you would use Odin to flash.
In order to use cwm, it has to be installed on your phone. cwm was created in MD5 extension, so you need to use Odin to install cwm to your phone. Once cwm installed on your phone, in order to access it, you need to hold Vol up+home+power button to get to it, then you can use it to flash zip file.
Odin is an execution PC file (.exe), you download and install on your PC and it used to flash MD5 file. In order for Odin to talk to your phone, you have to put your phone in "download mode". By remove battery, plug in usb cable between your PC and phone, press Vol down button, this will put your phone in download mode, now you re insert battery back to ensure a stable data transfer between your PC and phone. Without put back battery, data transfer may fail. After this, Odin is ready to flash Md5 file to your phone.
Like I said, let me know what's on your phone and what you want to achieve, I can help you step by step to get it done. After you have some practice, you will understand what involved and how to use them. Cheers!!!
re
yeah.. i should have just read through the forums a day or so to figure out the odin / rooting / rom process for this phone.
But i am a seasoned vet in the android world and got pretty frustrated, mainly because a few of the other xda forums made me a little jaded by the process.
I have a fully functioning 2.3.6 rooted charge with CWM and the edited build prop to keep the Unwanted ota updates from bugging me.
Thanks for not flaming the f-out of me.
BTW have yall come across a thread about sandblasting or sandpapering the back cover of the phone to make it less slippery? I have sweaty f-ing hand, i know gross, but its a slippery phone for me.
sprintrjm said:
yeah.. i should have just read through the forums a day or so to figure out the odin / rooting / rom process for this phone.
But i am a seasoned vet in the android world and got pretty frustrated, mainly because a few of the other xda forums made me a little jaded by the process.
I have a fully functioning 2.3.6 rooted charge with CWM and the edited build prop to keep the Unwanted ota updates from bugging me.
Thanks for not flaming the f-out of me.
BTW have yall come across a thread about sandblasting or sandpapering the back cover of the phone to make it less slippery? I have sweaty f-ing hand, i know gross, but its a slippery phone for me.
Click to expand...
Click to collapse
Not a problem, you can get a back cover from ebay for a few bucks and it will do the trick.
Seems like you already knew how to handle cwm, why don't you flash (using cwm) FP1 eclipse rom, kernel and radio, so you will be on the latest O/S?
This may not be a traditional Q&A format, but I really wanted to make sure that the plan I have in mind is going to work out for me.
Hi! I'm a noob. I want to flash my first ROM ever after having gotten frustrated beyond belief with how often my Infuse crashes (every few hours I get the triple vibrate to crash). I've already rooted the Infuse and installed CWM though it seems that it was pointless for me to do both of these things as the steps I'm to follow seem to install the both of 'em.
Phone: Samsung Infuse
Carrier: AT&T
Current Firmware version: 2.2.1
Baseband version: I997UCKH1
Kernel version: 2.6.32.9
Build number: FROYO.UCKH1
ROM I want to install: Unofficial CM10
Steps I intend to take:
Back up with Titanium Backup (Free) - Done as according to ctkatz's thread.
I did not do a launcher backup, mostly because I don't know what it is and I don't believe I have one I'm interested in keeping. Also, I didn't use Rom Manager to make a nandroid backup since in the threads I've read the general consensus seems to be Rom Manager is REALLY AWESOME at bricking phones, but not so good for much else.. Rather, I booted into CWM and told it to make a backup. I'm under the impression this made a nandroid backup. If this didn't, please somebody let me know.
Install 2.3.6 Gingerbread via jscott30's thread and installing option D. And for some reason, this is the only step that requires me to use Odin. I'm not really sure why, if anybody wants to clear that up it'd be great!
Use Qksters EFS backup script to ensure that if I somehow mess things up, I can still save my phone! And to run this I just "flash" it like I would a ROM. Which is by selecting the install zip from sdcard option.
Follow Entropy's CM9 guide to go from GB to ICS And this is just because you can't jump from GB to JB? I'm assuming it's something along those lines. Either way, his guide seems straightforward enough. Also during this step, put the ROM, Overclock Kernel, and Gapp files for CM10 on my internal SD card.
Wipe in CWM
Flash the ROM in CWM
Flash Overclock Kernel in CWM because if I'm going through all this trouble to doctor my Android, I may as well give myself the ability to overclock it
Wipe Cache Partition in CWM I don't really know what this does, but I'm assuming it doesn't wipe anything I care about
Advanced/Wipe Dalvick Cache Same as the previous step. I don't know what it does, but I'm following instructions.
Reboot And I'm supposed to understand this first reboot will take like 5-10 minutes and I shouldn't run around my house crying that my phone broke when it takes a long time to reboot.
Wait 15 minutes and reboot a second time
Log into google account And this gets my contacts back
Restore user app data This gets my apps and my 3 starred all angry birds levels back?
CAREFULLY restore some system data that is green
And after that, I get to play around with my brand new shiny OS and enjoy my phone!
I apologize that this is not a very concise accumulation of questions, but there's not really a single guide that goes step by step through this ENTIRE process of going from Froyo to a customized jellybean OS while making sure you don't lose any app data. It's taken me about ~5 hours of reading through a number of topics and my brain is starting to feel fuzzy, so I really just wanted some of the more experienced members of the community to doublecheck my planning.
Thank you guys so much! Everybody in this community is just awesome for dumbing this process down for those of us who do not understanding the inner workings of a computer : ). I'm very appreciative!
You have pretty much the right idea.
There's a few pointer i would suggest. Back up your contacts to google. Save all your photos to your PC.
When you are making the move from 2.2.1 to 4.1.2 or 4.2, I would start it all new. I would not restore anything you had in froyo (2.2.1) to 4.1.2.
With that in mind, put your phone into download mode, flash jscott's gb with bootloaders.
Flash cm9 and then cm10 as instructed on their ops or andros's write up.
Also I noticed you have a step about flashing the OC kernel, but OC has now been integrated into the kernel that comes with the build.
And as qkster stated, avoid restoring data. If there is something essential you do not want to lose you may restore data for that specific app and in case you start having issues, you know what to blame.
Sent from my SGH-I997 using xda app-developers app
qkster said:
You have pretty much the right idea.
There's a few pointer i would suggest. Back up your contacts to google. Save all your photos to your PC.
When you are making the move from 2.2.1 to 4.1.2 or 4.2, I would start it all new. I would not restore anything you had in froyo (2.2.1) to 4.1.2.
With that in mind, put your phone into download mode, flash jscott's gb with bootloaders.
Flash cm9 and then cm10 as instructed on their ops or andros's write up.
Click to expand...
Click to collapse
Luckily, the guide I read on backing up suggested both of those things, so I've done those.
I'm underway! I managed to successfully install the option D from jscott, but I'm a little confused on how to flash the bootloaders. Do I need to put my phone back into download mode to use Odin again? I tried that, and Odin doesn't seem to want to recognize my phone.
And sadly, I can't skip out on the bootloaders as I'm sure you guessed. Upon trying to go to CM9 I failed miserably due to rainbows. I actually used your guide to get back to well, stock UCLB3, and from there I've been trying to get the bootloaders on by putting my phone in download mode.
With no luck, sadly. Odin just doesn't want to show my phone as connected. Kinda stuck at the moment!
EDIT: I re-read the guide of yours I followed and saw that all I had to do was flash the thing a second time with the install bootloaders box checked. Unfortunately, I've done that, and I can clearly read the words "Uploading SBL...SBL upload failed!" on my screen.
Doesn't take much of a genius to figure out that the BL likely stands for bootloaders, so now I'm slightly freaking out. Heimdall One-click is currently trying to end the session. I'm of course going to let it go as long as I can hoping that it ends things nicely as I'm terrified to try turning anything off at this point. Hopefully I didn't just permanently destroy my phone =\
Andros: Oh thank you for saving me from the OC mishap. I suppose there's some good in me not having gotten that far yet due to problems!
EDIT 2: I can see the light at the end of the tunnel! I swapped my USB ports around a bit and kept trying with your Heimdall One-click stuff and finally got the bootloaders in! Once that went through the rest was easy as pie : ) Everything's going smooth, I'm currently installing JB Gapp stuff, then I'm going to follow the rest of my ROM guide and I don't forsee any issues. Thank you guys again, both of your guides and your responses were very helpful!
I want to thank YOU arguro. If everybody had the patience and intelligence to so thoroughly research what they wanted to do there would be so many less help I bricked my phone threads and a whole lot less irritated developers.
You went into the process with the right amount desire / fear. Glad you made it and welcome to jellybean!
Sent from my SGH-I997 using xda app-developers app