Database Info

[q] help! My phone wont do anything!

hey guys,
my phone litteraly wont do anything. i f*ed up some fonts using type fresh, then tried to restore using the odin3 downloader. i accidentally closed it, and now my phone wont boot up/react to any buttons pressed. any help? thanks guys!

had the same problem. i cant figure out how to even get odin working, it says one click but when i hook up it to odin it gives me a message that still doesnt tell me ****. i had to send my phone back for a new one and told them i used easyroot on the market bc i didnt know what it was and it sounded cool but now i know not to ever do that again that it messd up my phone. Praying to god that they dont charge my for anything

You should still be able to enter bootloader mode by turning phone off and holding down up/down vol and pwr simultaneously until boot screen flashes then release power button only

it wont even do that

open odin (use the stock one click version)
with the phone off (remove/reinsert the battery if need be) and not plugged in; hold vol. down and insert the usb cable (keep holding vol. down untill you see the download screen). this should put you into download mode and if you have the right drivers odin should recognize the phone.
I've stuffed my captivate on a few occasions and so far I have been able to use this method to get into download mode and fix it.

it wont do anything at all. it wont power on, show up in adb, anything... and stupid att wont do ANYTHING -_- oh well. any help would be appreciated!

Have any of you offering support to the OP actually had your phone in the described state? I've read a few posts where the phone is seemingly completely dead as the OP describes and no one says they've successfully recovered from that state. All I ever see is the same old button combinations/battery/usb shenanigans and statements of that should work and that the phone is unbrickable. I have personally seen a device that was behaving in such a manner and no combination of battery pulling, usb plugging, button holding, or tongue twisting would generate anything from the phone. The only thing the phone would do was get hot.

same here. Phone showed bright green screen...wasnt done with teh flash and said it was finished...now the nly thing I can get is power and hold the vlume up for some IRQ and hex stuff. I posted a questionthis morning but...serious. Vol up and down and any things else gives nothign but a black screen..battery out...back in anything..its torched.

Have you tried getting into download mode via the sdk?
Sent from my SAMSUNG-SGH-I897 using XDA App

daveshih said:
Have you tried getting into download mode via the sdk?
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
when i plug it in, windows doesnt make any noises and doesnt recognize it, and when i use the "adb devices" command, nothing shows up.

daveshih said:
Have you tried getting into download mode via the sdk?
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
Did you read the rest of the posts? The OP already stated several times that the phone does nothing. I realize that most people will say it does nothing or is "bricked" if it simply shows the "connect to computer" screen, but the OP has stated more than once that the phone shows nothing. Yes, everyone is trying to help, but simply repeating what has been said numerous times before doesn't help.
Has anyone actually recovered a phone that displays NOTHING? No logos, no recovery, no nothing.

Last night, i turned off the light in my room when i noticed a glowing from my desk. i walked over, and it turns out my captivate's screen was in fact on, it was just a faint black glow, and none of the power buttons would do anything. when i took the battery out, it shut off completely!

As I pointed out here
http://forum.xda-developers.com/showthread.php?t=757293
Im pretty sure it was my fault for not completely following instructions on the ext4 one click install root, settings.db etc so everyone needs to make sure if the dev says flash before..do it.
State of the phone was, it would not completely power on..therefor no usb drivers would load and Odin cannot see the phone and it can no longer flash..the only thing I could get it to do was show a screen with that text. I put in my post. I ordered it via letstalk.com so I sent it back and assuming they get the same result Ill have a new one hopefully by the end of the week. Im just glad I stil had my old iphone3 to slap my sim card in.
The odin one click flash thing..it just flaked right at the start it looked like..but I cant be sure because as soon as I saw a blue progress bar I stepped into the kitchen for abtou 30 sec..I came back and the screen was florescent green and Odin said it was done. I knew something was wrong as it was way too fast so I unplugged, removed the battery and set it back in...from there on out it would do nothing with the power button unless on a semi rare occasion if I hit the volume up button and power I got the IRQ stuff.
Annoying as I had a nandroid backup just before I started messing with it.

i just sent mine into samsung... back to mah ol trusty blackjack. gonna have to get used to supermario bros 3 instead of spyro....
ANYWAYS theyre sending me a new one!

uiskibum said:
open odin (use the stock one click version)
with the phone off (remove/reinsert the battery if need be) and not plugged in; hold vol. down and insert the usb cable (keep holding vol. down untill you see the download screen). this should put you into download mode and if you have the right drivers odin should recognize the phone.
I've stuffed my captivate on a few occasions and so far I have been able to use this method to get into download mode and fix it.
Click to expand...
Click to collapse
So, yes in same state as op... no nothing... couldn't get jack out of it. at all, none
what this post said worked.... not holding power button... nothign...
removed battery
plugged in battery
hold vol down
(still no response)
plug in usb cable and continue holding vol down.
it went to recovery mode
... no holding of power button, just vol down and plugged in USB... give it a shot man, let me know
EDIT: feel free to PM me if you want me to help walk you through it...

ace518 said:
So, yes in same state as op... no nothing... couldn't get jack out of it. at all, none
what this post said worked.... not holding power button... nothign...
removed battery
plugged in battery
hold vol down
(still no response)
plug in usb cable and continue holding vol down.
it went to recovery mode
... no holding of power button, just vol down and plugged in USB... give it a shot man, let me know
EDIT: feel free to PM me if you want me to help walk you through it...
Click to expand...
Click to collapse
Hey thanks, but i already sent it to em... thank you everyone for your help!

Just a note... i said before hold vol down and plug in usb. I had it in a pretty bad state tonight. Played around. Same idea as before, but had to hold vol up and vol down. If i brick a few more times, i'll give a better guide. But this phone can DEFINITELY come back from a state where you can't even get it to power on. Figured any additional info on this would be good.

Some Captivates Unable to Use Three Button Recovery

It appears that some newer Captivates being sold suffer from not being able to reboot into download or recovery mode using the three button (VOL UP + VOL DOWN and PWR) combination. These phones will not respond to these key combinations. If you have one of these phones, you have a significantly higher risk of bricking your phone irreversibly since you cannot three button reboot into download mode from a failed flash.
The first two Captivates I used did not have this problem. The two Captivates I got this week both DO have this problem. Others who have purchased their Captivate recently (in the past week) have discovered this problem as well. This indicates it may be more common in newer Captivates.
A number of Galaxy S I9000 have experienced this problem and they have put pressure on Samsung Canada via Facebook to fix the problem. For those affected, I suggest we do the same for our Captivates:
http://www.facebook.com/SamsungMobile?v=wall
Examples of Captivates that can't use three button recovery:
http://forum.xda-developers.com/showthread.php?p=8066648
and from I9000 users:
http://forum.xda-developers.com/showthread.php?t=765703

Asked and answered my own question. Relevant information condensed into the post above.

Pretty sure you can still do it... try this
shut down your phone, plug in the usb cable and wait for the battery to come up, then do the key combo.

I call user error. How and why stop key combos? I wouldnt think it would happen.

smokestack76 said:
I call user error. How and why stop key combos? I wouldnt think it would happen.
Click to expand...
Click to collapse
I've went through 2 cap's also, both cannot do it. I have to use ADB to kick into recovery. Also, in the SRE thread another user had the same issue. All bought within the last week..

Thanks for the heads up. I was planning on swapping mine out because it isn't consistently detecting my SIM card; looks like I should wait for a bit and see if this is a temporary issue.

I swapped mine so its the so called newer one. And i can still use the buttons just fine. Even tried with another one today and still worked fine. So i dunno.

To clearify some issues. Power off. Hold power and BOTH volume buttons down. Thats the key here. Once the att screen comes on wait. Dont do anything. The screen turns off. THEN the screen comes back on. Thats right twice. THEN release the power button. ONLY the power button and continue holding the volume up AND down. You will see recovery menu.

thats exactly how we are doing it. its the download that is having issues though, not recovery. thats holding both vols, pluggin in USB. it should go to Download mode, but it doesnt.

Ok just tested. Same thing with usb plugged in takes you to download.

Make sure odin is up and running. And usb is plugged in when u power off. Not sure if its needed but thats how i tested it.

Worked fine here plugging in a usb after powed off.

If this does not work for you please post a system dump. Or pm me for more help. Kinda wonder why so many users have these issues :-(

I was having these problems as well.. When I first got that phone I tried to boot it into recovery mode, and it wouldn't work.. THe only way I was able to get it into recovery mode was through quick boot.
So while I was flashing the SRE v 1.2.2a somehow it got stuck in a loop of installing the files over and over..
I tried putting the phone into download mode via every button combination people suggested.. I literally am not exaggerating that I spent 4 hours trying over and over..
Today i sent it back rma.

Take your phone back if 3 button recovery mode does not work
malfuncion said:
I've went through 2 cap's also, both cannot do it. I have to use ADB to kick into recovery. Also, in the SRE thread another user had the same issue. All bought within the last week..
Click to expand...
Click to collapse
Here is my suggestion. Take your phone back if it does not do the 3 button recovery mode. Otherwise you will sooner or later brick it and not be able to recover:cool. Take it from someone who has bricked one that could not do the 3 button recovery mode. I lucked out and got a new phone that does do the 3 button rec now LOL. Test the phone in the store to ensure it can go into recovery mode.

smokestack76 said:
To clearify some issues. Power off. Hold power and BOTH volume buttons down. Thats the key here. Once the att screen comes on wait. Dont do anything. The screen turns off. THEN the screen comes back on. Thats right twice. THEN release the power button. ONLY the power button and continue holding the volume up AND down. You will see recovery menu.
Click to expand...
Click to collapse
Did this for about 2 hours on both devices. No joy. If you follow the links I posted in the first post, you'll see that a number of I9000 devices have this problem and now a couple of ours do as well. It has to do with the way they are flashed from the factory.
I can certify (unless I have gone completely mental) than I am doing it the right way. I had two Captivates before this that I could put into download and recovery easily using the vol up + vol down + pwr combo. The last two, no way. Also cannot do the vol up + vol down then plug in USB with ODIN running and ready to get out of brick mode (i.e. computer -!- phone). Which means once bricked, always bricked.
I've attached build info for the device. JF6, built 8.11.2010, hardware is REV0.4.

ok so I am basically screwed then. I just called AT&T and they wont warranty the device. Do I have to call samsung? I got that number: 18889874357.
AT&T didnt even know what a recovery mode was, they wanted to walk me through the factory reset on the phone itself.
Has this issue been confirmed with Samsung?

Called Samsung this morning- actually just got off the line. I spoke to about 3 people, then finally got to level 3 support. They stepped me through the same steps I have read everywhere- the 3 button reset. He actually had me try it a few different ways too. After a second, he put me on hold to see if there is some other way to put the phone into recovery or download mode, but after 5 minutes he came back and had no good news. He had a couple things he googled but they didnt work- of course. He basically resolved the call with "I don't know what to do..." So I then asked if this is an RMA'able problem and he said he didnt think so since the phone functions fine but put me on hold again for another 5 minutes. Finally he came back and said he can setup an RMA to do a factory reflash. It is a 2day air to send it to them, then a flashing, and a 2day back. Should take about a week or so. He suggested I maybe go to AT&T and possibly get it replaced that way first so I will head over to corporate this evening. If that doesnt work then I'm sending it off to Samsung...

I had much difficulty getting into recovery. But it turned out to be a matter of timing. Using the usb cable plugged in seems to change the criteria and made it easier to get into recovery.
What I do now. Phone is off. Wait at least 10 sec after shutdown to ensure it is fully off. In low light you may see a small amount of light coming from the screen then it goes black.
Press both volumes then the power button and hold till the att screen pops up. After att screen is on (the initial screen not the animation) for one or two second. Release power then volume quickly. If that doesn't work try it as design gears describes with the usb cable.
Sent from my SAMSUNG-SGH-I897 using Tapatalk

Dani897 said:
What I do now. Phone is off. Wait at least 10 sec after shutdown to ensure it is fully off. In low light you may see a small amount of light coming from the screen then it goes black.
Press both volumes then the power button and hold till the att screen pops up. After att screen is on (the initial screen not the animation) for one or two second. Release power then volume quickly. If that doesn't work try it as design gears describes with the usb cable.
Click to expand...
Click to collapse
Tried umpteenth different timings. Now that I have one of my original Captivates back, the difference is clear. I can get it into recovery/download 100% of the time. On both the new ones, 0% -- as in never. It's gonna be a fun conversation at the AT&T store trying to tell them that:
1. The phone is broken because I can't get it to switch into a mode mainly reserved for engineers.
2. I will test the replacement they give me for the same problem and return it if doesn't work.
3. Repeat step 2 until I find one that works.

Phone is stuck on a screen maybe bricked during flashing????

Ok I was flashing back to stock 2.1 useind odin when mid process my phone fell battery out usb disconnected and bam thats it. Now my phone is locked on a screen that shows a picture of a phone ! and a computer. I can get it back to download mode and odin will se the phone but gets no further then do not unplug device, my computer beeps when its plugged in but it dose not show the phone in my computer section. Any fixes or am i screwed?
PS phone is only two weeks old if need be could I take it back like this????

Hmm I think I may hove gotten past this problem. Uninstalled odin reinstalled and now it seems to be hopefully working

Here is the fix
I was in this same situation yesterday. Here is how to get it back into download mode.
•Be sure the Samsung USB drivers for the phone are installed on your computer.
•Remove and replace the battery.
•Connect the phone to the computer with the USB cable. The "phone-exclamation mark-computer" picture should display on the phone's screen.
•Hold the Volume Up+Volume Down+Power buttons down simultaneously.The screen should go blank, then the picture should appear again. When the screen goes blank a second time, release the Power button while continuing to hold the Volume Up+Volume Down buttons down

If that doesn't work,i had a similar problem where I could get into odin, but it would progress beyond the pit file. Take the battery, sim and memory card out of your phone. Start odin. Put the battery only back in. hold volume up and down. Plug the phone in while holding these buttons. Don't let go until you are in download mode. Now try restoring. It should work.

Thanks for the input i am back up and running!!
Sent from my SAMSUNG-SGH-I897 using XDA App

Bricked replacement Captivate - Orange Screen
Just to let you know. I recently received a replacement captivate thru warranty exchange. The phone was apparently a new one with JF6. So I decided to do an update to JH7 using Kies mini. A little over half way to the update procedure, the phone screen turned orange and stayed there for a long time, eventually I had to pull the plug. Of course I had to manually go to download mode and launch Kies mini emergency recovery, the damn thing again got stuck at the orange screen.
If anybody has this experience do no proceed further and throw that damn thing back at At&T's face. Do not attempt to do anything. I made a mistake of then doing an ODIN one-click back to stop and the phone got stuck half way, went to the orange screen.. and then it was over.. The phone was dead, wouldn't turn on, no recovery or download mode with any button combo. When I plugged in to the wall, no battery indicator.
save yourself the trouble and return the damn thing

still there
I am a "noob" to posting here, and a noob to the android due to being an avid iPhone user. I am having the same problem, phone -!- computer and have tried every method i can find in this forum to get passed it. Are there any other thoughts or suggestions? (got hung at do not turn off target in odin) Thanks in advance to any help.

I would look at this thread http://forum.xda-developers.com/showthread.php?t=1153310

Stephenv1971 said:
I would look at this thread http://forum.xda-developers.com/showthread.php?t=1153310
Click to expand...
Click to collapse
went that route, still cant find dl mode. have resistors built and all. any way i try to boot shows me the phone -!- computer, and the computer doesnt attempt to recognise it so there is no communication between the computer and phone. unfortunately, i dont have a v/ohm meter, so i am not sure of the accuracy of the resistors i used to make my jig.

I fixed this many times with phone that had the button download mode and didn't.
Getting into download mode while softbricked like this wont show the normal download screen. IT will still show the error screen....
With download mode working still:
Simply remove the battery and replace,
Open odin
Hold down volume keys and plug it in till you see odin recognize ur phone.
Then continue to use odin.
Dosent work, repeat.
If you know ur button combo dosent work:
Just open odin.
Remove battery & replace.
Use jig (3k 100k ohms twisted)
Then when the phone turns on and your see the pc! screen plug in usb.
See if odin sees it.

Assuming your flash didn't fail on the PBL.bin or SBL.bin you should be fine.
Follow the methods suggested by other users here and you will get back up and running in no time at all.

Don't sweat the 'phone-!-pc' screen. I'm a little surprised that no one has given you the good news....that is just a version of the download screen for later hardware revisions. It looks bad, but if Odin recognizes your phone (if one of the COM fields goes active), just start your flash again.
Now if Odin does not recognize the phone when plugged in via USB, then you have some more work to do.

I had forgotten about posting here, and my problem has been resolved. So here it is... I tried everything that I could find within this forum, almost. I built my own jig with inferior radio shack components that would not activate download mode, though it would turn the phone on. I got wise, spent 8 dollars at ebay and purchased a JIG there. Instant download mode after 3 days (shipping). Reflashed with one click, updated w/ kies, made kernal changes and am now rockin my captivate. Thanks to those who assisted.

Steve_O_1971 said:
I had forgotten about posting here, and my problem has been resolved. So here it is... I tried everything that I could find within this forum, almost. I built my own jig with inferior radio shack components that would not activate download mode, though it would turn the phone on. I got wise, spent 8 dollars at ebay and purchased a JIG there. Instant download mode after 3 days (shipping). Reflashed with one click, updated w/ kies, made kernal changes and am now rockin my captivate. Thanks to those who assisted.
Click to expand...
Click to collapse
Using the 3-resistor method takes A LOT of patience, at least in my experience. Glad everything worked out.

beast534 said:
Using the 3-resistor method takes A LOT of patience, at least in my experience. Glad everything worked out.
Click to expand...
Click to collapse
Patience is a virtue, and my Ex's name. LOL! I can do without patience.
Jokes aside, i actually soldered the resistors to a plug that i had cut up, and made sure it was covered so my skin wouldnt come in contact. The Radio Shack here buys inferior products and sells them at reggular retail. Unfortunately my $300.00 V-Ohm meter is on the fritz, and i have not had the time or money to replace it yet, but I have intentions to check the actual resistance of the jig I made. ^^

Samsung Infuse boots to logo..

I saw a Samsung Infuse 4g for sell as is. Only thing is it boots to Samsung logo then turns off. No water damage. Do you think can be fixed with a hard reset or some other solution?
Sent from my SGH-I897 using XDA

darkchyldx101 said:
I saw a Samsung Infuse 4g for sell as is. Only thing is it boots to Samsung logo then turns off. No water damage. Do you think can be fixed with a hard reset or some other solution?
Sent from my SGH-I897 using XDA
Click to expand...
Click to collapse
Sounds like an easy fix. odin back to stock and your set. also if it already has CWM installed, super easy to instal custom rom with out the odin part

I just bought it for $160 in great condition with all accessories except for the booting issue. I should get it next week. Its a great price if I can get it to boot up. Any suggestions will help. Hopefully its an easy fix.. if not I'll throw it back up on eBay.
Sent from my SGH-I897 using XDA

darkchyldx101 said:
I just bought it for $160 in great condition with all accessories except for the booting issue. I should get it next week. Its a great price if I can get it to boot up. Any suggestions will help. Hopefully its an easy fix.. if not I'll throw it back up on eBay.
Sent from my SGH-I897 using XDA
Click to expand...
Click to collapse
Its a really easy fix:
1) download odin-look in the super thread
2) put phone in download mode
3) run Odin
4) your phone will now turn on
This phone is 99% unbrickable...the only way its gonna brick is if you have actually hardware failure, if Samsung logo pops up then there a simple Odin back to stock will fix it
Sent from my SGH-I997 using XDA

Thanks for the suggestions. I'll post some more updates after I receive the phone and make the fixes.

Well got the phone used Odin back to stock...its up and running except camera. So I installed Zeus build 6 still camera not working.
Sent from my SAMSUNG-SGH-I997 using XDA

It is possible the camera was broken physically.
Are both cameras not working? Is there an error message that comes up when you open the camera app?
You might want to email the ebay seller and ask if they had trouble with the camera before it got bricked.

I found a solution. I turned my location off in settings then reapplied camera firmware. It works. The key was just to turn off my location. Weird huh. I can turn my location back on now too. Phone works good as new just flashed Zeus rom build 6 nice! But I miss my CM9 on my Captivate.

darkchyldx101 said:
I found a solution. I turned my location off in settings then reapplied camera firmware. It works. The key was just to turn off my location. Weird huh. I can turn my location back on now too. Phone works good as new just flashed Zeus rom build 6 nice! But I miss my CM9 on my Captivate.
Click to expand...
Click to collapse
they have an unofficial Cm9 you should try that.
Sent from my Nook tablet running MiUi 2.2.3 Alpha (GB 2.3.7) Rom useing XDA premium.

Similar problem
I'm having this same problem with my phone. It boots to the logo and then immediately turns off and does it again. I found ODIN-lite here, but that's where I'm stuck. I don't know how I can do step #2, put my phone in download mode, because it never turns on all the way. When I plug it in to my computer, it boots up to the charging screen and then promptly restarts. My phone is not rooted. Am I SOL?
mg2195 said:
Its a really easy fix:
1) download odin-look in the super thread
2) put phone in download mode
3) run Odin
4) your phone will now turn on
This phone is 99% unbrickable...the only way its gonna brick is if you have actually hardware failure, if Samsung logo pops up then there a simple Odin back to stock will fix it
Sent from my SGH-I997 using XDA
Click to expand...
Click to collapse
---------- Post added at 12:19 PM ---------- Previous post was at 11:31 AM ----------
I found the "stuck in a bootloop" thread. I've tried pulling the battery, putting it back in, holding power + both volumes when the Samsung screen comes on, and then releasing the power button. I've also tried to go into download mode by putting the battery in, plugging the USB in to my computer, and holding down both volume buttons. Neither of those do anything. If only the battery is in, it just boot loops to the Samsung screen, if the battery and USB are in, it bootloops to the battery charging screen. It never asks me what mode I want to go into when I'm plugged in to my computer. I'm pretty sure none of the buttons are broken, as I used them all the time before my phone randomly started boot looping.
HonestIago said:
I'm having this same problem with my phone. It boots to the logo and then immediately turns off and does it again. I found ODIN-lite here, but that's where I'm stuck. I don't know how I can do step #2, put my phone in download mode, because it never turns on all the way. When I plug it in to my computer, it boots up to the charging screen and then promptly restarts. My phone is not rooted. Am I SOL?
Click to expand...
Click to collapse

HonestIago said:
I'm having this same problem with my phone. It boots to the logo and then immediately turns off and does it again. I found ODIN-lite here, but that's where I'm stuck. I don't know how I can do step #2, put my phone in download mode, because it never turns on all the way. When I plug it in to my computer, it boots up to the charging screen and then promptly restarts. My phone is not rooted. Am I SOL?
---------- Post added at 12:19 PM ---------- Previous post was at 11:31 AM ----------
I found the "stuck in a bootloop" thread. I've tried pulling the battery, putting it back in, holding power + both volumes when the Samsung screen comes on, and then releasing the power button. I've also tried to go into download mode by putting the battery in, plugging the USB in to my computer, and holding down both volume buttons. Neither of those do anything. If only the battery is in, it just boot loops to the Samsung screen, if the battery and USB are in, it bootloops to the battery charging screen. It never asks me what mode I want to go into when I'm plugged in to my computer. I'm pretty sure none of the buttons are broken, as I used them all the time before my phone randomly started boot looping.
Click to expand...
Click to collapse
Two things: to get into download mode, you pull the battery, hold down one of the volume keys (I forgot which one!), insert the usb cable, and put the battery back in. Or something like that. The crucial point is that you should be holding down ONE of the volume buttons.
The other thing is that you may have a stuck power key. Fairly easy fix. Find the thread in the General section.

Actually he is doing it the right way. One must press both vol buttons to enter download mode.
But effectively your phone seems to have a stucked power button.

[Q] Im having issues with my phone right now.

Hey guys i have a samsung infuse 4g and one day it just turned off now it goes on and goes to the samsung logo then goes of and back to the samsung logo over and over again. i take the battery out and put it back in then it just does the same.

I really need help here. Its my moms phone and shes freaking out cause she cant afford a new phone so I need to get this fixed or atleast find out whats wrong with it. I let the battery die all the way down but still same issue.

This is a common problem. You need to get the phone into download mode and use either Odin or heimdall to revert the phone to stock. There are several links to several guides on the site, and the super everything thread has most of them. Search is your friend.
My Infuse is Stalking Beans

the phone wont even go into download mode because it shuts off too fast

Have either Heimdall or Odin on your PC ready to go with the correct drivers installed. Then take the battery out. Plug in the USB connection to the PC (preferrably a USB connection in the back of the PC). Hold Volume UP and Volume DOWN (but not the Power Button). Then insert the Battery, this will put you into download mode. Flash the "back to stock" of your choice.
If this doesn't work, you have a power button issue. Search for that fix then.

it's prolly the power button loop..look in the general thread and the q/a, M

Ended up smacking the phone around a little bit and fixed it right up xD good times.
Sent from my SAMSUNG-SGH-I337 using xda app-developers app