[Q] cp_modem.bin - Verizon Droid Charge

So here is the rundown. I flashed GC 1.9RC2.3 and was getting some force closes. Tried Data/Factory Reset and that still didn't fix the issues. So now I'm trying to reflash GC 1.9 FE to restart over and ODIN has been stuck on cp_modem.bin for the past 20 minutes.
<ID:0/004> File analysis..
<ID:0/004> Enter CS for MD5..
<ID:0/004> Leave CS..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> dbdata.rfs
<ID:0/004> lte_modem.bin
<ID:0/004> param.lfs
<ID:0/004> Sbl.bin
<ID:0/004> cp_modem.bin
Is this normal? I don't remember it taking this long to flash the previous time.

WilliamKingX17 said:
So here is the rundown. I flashed GC 1.9RC2.3 and was getting some force closes. Tried Data/Factory Reset and that still didn't fix the issues. So now I'm trying to reflash GC 1.9 FE to restart over and ODIN has been stuck on cp_modem.bin for the past 20 minutes.
<ID:0/004> File analysis..
<ID:0/004> Enter CS for MD5..
<ID:0/004> Leave CS..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> dbdata.rfs
<ID:0/004> lte_modem.bin
<ID:0/004> param.lfs
<ID:0/004> Sbl.bin
<ID:0/004> cp_modem.bin
Is this normal? I don't remember it taking this long to flash the previous time.
Click to expand...
Click to collapse
Are you using the PDA button? Did you reinsert the battery after Odin recognized your phone?

sounds like slow USB connection...try another usb port.. preferably a rear port...the modem does take a bit to flash and progress shows on device for modem

Yes I am using PDA and I have been using ODIN since my Vibrant and never had to take the battery out to flash. As far as moving the USB to a different port, if I cancel out the install right now will I be perma-bricked?
Update: So I switched USB ports and it flashed pretty quickly. I guess the port on the front wasn't cutting it.

let it go if the staus bar is moving on your device...otherwise you dont really have a choice but to turn Odin off and start over...but I guess 'YES" you can brick your device

chiahead52 said:
let it go if the staus bar is moving on your device...otherwise you dont really have a choice but to turn Odin off and start over...but I guess 'YES" you can brick your device
Click to expand...
Click to collapse
Yeah I was nervous as hell to stop the download. I just closed ODIN out first and then took out the battery. Crossed my fingers and hoped for the best. I'm glad it went through the second time because I would've been pissed if I had to send my phone off.

The only time I've seen bricks is when something happens in odin to interrupt the flashing of boot.bin

hazard209 said:
The only time I've seen bricks is when something happens in odin to interrupt the flashing of boot.bin
Click to expand...
Click to collapse
Thanks for the knowledge. Hey Hazard I noticed your name in the credits of GC 1.9RC2.3 when I flash it. Could you check out my other question regarding the G-Talk app and any suggestions you have about it would be great.

Related

[Q] URGENT !!! Need help quick please

Was running stock rooted Ed1 Rooted with Gingersnap. Took update to ED2 and lost root. Tried to root again with Gingersnap didn't take. Went back into phone via odin to roll back to ED1 and while it was connected and in process, cat jumped onto desk and bumped phone and it lost USB connection.
Got FAIL in Odin. Put battery in phone and just get yellow droid - ! - computer image.
Now in Odin trying to roll back and it is just sitting at Initialzation.
WHAT CAN I DO ?!!!
Really need this phone for work tomorrow ...
Any help GREATLY appreciated.
Steve
[Q] URGENT !!! Need help asap please !!
Was running stock rooted Ed1 Rooted with Gingersnap. Took update to ED2 and lost root. Tried to root again with Gingersnap didn't take. Went back into phone via odin to roll back to ED1 and while it was connected and in process, cat jumped onto desk and bumped phone and it lost USB connection.
Got FAIL in Odin. Put battery in phone and just get yellow droid - ! - computer image.
Now in Odin trying to roll back and it is just sitting at Initialzation.
WHAT CAN I DO ?!!!
Really need this phone for work tomorrow ...
Any help GREATLY appreciated.
Steve
Chopstix9 said:
Was running stock rooted Ed1 Rooted with Gingersnap. Took update to ED2 and lost root. Tried to root again with Gingersnap didn't take. Went back into phone via odin to roll back to ED1 and while it was connected and in process, cat jumped onto desk and bumped phone and it lost USB connection.
Got FAIL in Odin. Put battery in phone and just get yellow droid - ! - computer image.
Now in Odin trying to roll back and it is just sitting at Initialzation.
WHAT CAN I DO ?!!!
Really need this phone for work tomorrow ...
Any help GREATLY appreciated.
Steve
Click to expand...
Click to collapse
disconnect the phone, close odin, reopen odin , plug your phone back in , put it in download mode insert the battery and flash again
Same thing ...Oding just sits here at this point:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> Enter CS for MD5..
<ID:0/003> Check MD5.. Do not unplug the cable..
<ID:0/003> Please wait..
<ID:0/003> Checking MD5 finished Sucessfully..
<ID:0/003> Leave CS..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
Chopstix9 said:
Same thing ...Oding just sits here at this point:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> Enter CS for MD5..
<ID:0/003> Check MD5.. Do not unplug the cable..
<ID:0/003> Please wait..
<ID:0/003> Checking MD5 finished Sucessfully..
<ID:0/003> Leave CS..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
Click to expand...
Click to collapse
are you using a laptop or desktop?
Desktop front panel USB port. Same port I've used each flash. Will try moving to rear port ....
Chopstix9 said:
Desktop front panel USB port. Same port I've used each flash. Will try moving to rear port ....
Click to expand...
Click to collapse
yeah always use rear ports for best results
Seems to be hung up on KERNEL phase.
<ID:0/004> Check MD5.. Do not unplug the cable..
<ID:0/004> Please wait..
<ID:0/004> Checking MD5 finished Sucessfully..
<ID:0/004> Leave CS..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> factoryfs.rfs
<ID:0/004> recovery.bin
<ID:0/004> zImage
Never done this with battery in before. Pretty new to this and scared !!! LOL Appreciating the hell out of your help.
Chopstix9 said:
Seems to be hung up on KERNEL phase.
<ID:0/004> Check MD5.. Do not unplug the cable..
<ID:0/004> Please wait..
<ID:0/004> Checking MD5 finished Sucessfully..
<ID:0/004> Leave CS..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> factoryfs.rfs
<ID:0/004> recovery.bin
<ID:0/004> zImage
Never done this with battery in before. Pretty new to this and scared !!! LOL Appreciating the hell out of your help.
Click to expand...
Click to collapse
what are you flashing
stockrootedED1-20110517.tar.md5
Had been using this, then rooted with Gingersnap. Then installed superuser and open garden for wifi tether hotspot. Updated to ED2 and tried using Gingersnap again to root ED2 and it didn't take. Was hoping to do that to get rid of ED2 trying to be pushed. That brings us to current fiasco ... Just trying to roll back to ED1 same as other times ... Still sitting at zImage
Chopstix9 said:
stockrootedED1-20110517.tar.md5
Had been using this, then rooted with Gingersnap. Then installed superuser and open garden for wifi tether hotspot. Updated to ED2 and tried using Gingersnap again to root ED2 and it didn't take. Was hoping to do that to get rid of ED2 trying to be pushed. That brings us to current fiasco ... Just trying to roll back to ED1 same as other times ...
Click to expand...
Click to collapse
hmm try a different USB port, also if you have an antivirus running disable it
Dude you ROCK !! A/V was stopping it I think... Got it flashed using original battery out method. Battery in went to reboot screen hit home and she booted. PHEW !!! It took a Xanax to settle me down from that, guess I ain't a bricked phone virgin no more
Was planning to wait until a more finalized Voodoo or good setup is complete to go all the way with phone. Was hoping to accomplish just a stock rooted ED2 for now..
Can't thank ya enough.
Chopstix9 said:
Dude you ROCK !! A/V was stopping it I think... Got it flashed using original battery out method. Battery in went to reboot screen hit home and she booted. PHEW !!! It took a Xanax to settle me down from that, guess I ain't a bricked phone virgin no more
Was planning to wait until a more finalized Voodoo or good setup is complete to go all the way with phone. Was hoping to accomplish just a stock rooted ED2 for now..
Can't thank ya enough.
Click to expand...
Click to collapse
congrats, very welcome
Just saw this exchange... made me feel good about being a member here... great community!!!
Sent from my SCH-I510 using XDA Premium App

[Q] Help soft bricked?

So here's what happened. I tried to install CWM 6.0.1.2 using EZ Recovery and it rebooted into ODIN with the words, could not do normal boot, in red. When I reboot it, it would just go back to the ODIN screen, so I tried to use the root 66 method. At first, it would get to system.img.ext4, but the green bar would barely move and be stuck there for 30 minutes. I would try again by taking out the USB cord, rebooting phone (maybe bad idea?). I did it again and it would be stuck there. I tried different USB ports on my laptop. Some will get to system.img and be stuck or get to recovery.img and say fail. Is my phone hard bricked or is there something else I can do? Thanks!
I also tried it on a different computer and it gets stuck on boot.img instead. Any help would be greatly appreciated!
It seems like using the older version of Odin gave me more consistent results. I now always get to system.img before it fails. The green bar gets 1/3 of the way then says failed.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Is there anyway to get it to be successful?

S6 stuck in download mode

Hi all,
Been searching these forums for the past 3 hours and trying numerous options and still haven't been able to fix my problem.
Long story short, dropped S6 in water, turned off and left in rice bag for 2 weeks.
Tried to turn on today and it only boots to download mode, everything else just reboots the phone. Also it will only turn on when connected to USB so i'm guessing the battery is dead also.
My main concern is I have photos that I really want to try and recover and yes I know I know, always have a backup, as a desktop technician I really should have had that setup on my phone but here we are.
So my main target is to somehow get into recovery mode and then use ADB to pull files from the phone.
I've tried to flash many different recovery files but they always fail in Odin v3.10.7, log for Odin is:
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1005)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
I don't want to flash stock firmware cause I'm guessing that will wipe the phone and photos?
Any help would be appreciated!
alicg said:
Hi all,
Been searching these forums for the past 3 hours and trying numerous options and still haven't been able to fix my problem.
Long story short, dropped S6 in water, turned off and left in rice bag for 2 weeks.
Tried to turn on today and it only boots to download mode, everything else just reboots the phone. Also it will only turn on when connected to USB so i'm guessing the battery is dead also.
My main concern is I have photos that I really want to try and recover and yes I know I know, always have a backup, as a desktop technician I really should have had that setup on my phone but here we are.
So my main target is to somehow get into recovery mode and then use ADB to pull files from the phone.
I've tried to flash many different recovery files but they always fail in Odin v3.10.7, log for Odin is:
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1005)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
I don't want to flash stock firmware cause I'm guessing that will wipe the phone and photos?
Any help would be appreciated!
Click to expand...
Click to collapse
A long time ago my s2 got stuck in download mode after getting wet, back then it was caused by some corrosion in the usb port. I fixed it by trying to scrape it clean with a usb cable, you could also try isopropylalcohol (even let it soak in there for a few days)
btw the s2 continued working up until this day (a friend now has it)
godutch said:
A long time ago my s2 got stuck in download mode after getting wet, back then it was caused by some corrosion in the usb port. I fixed it by trying to scrape it clean with a usb cable, you could also try isopropylalcohol (even let it soak in there for a few days)
btw the s2 continued working up until this day (a friend now has it)
Click to expand...
Click to collapse
I heard of this isopropylalcohol, so just fill a jar and drop phone in for few days? And then back in rice?
Spent 2 weeks drying the thing out, kind of worried to attempt this.
But as I've nothing to lose!
alicg said:
I heard of this isopropylalcohol, so just fill a jar and drop phone in for few days? And then back in rice?
Spent 2 weeks drying the thing out, kind of worried to attempt this.
But as I've nothing to lose!
Click to expand...
Click to collapse
I think isopropyl alcohol doesn't conduct, so no short circuits and no need to dry but from my experience with keyboards which got wet and not dried properly those thin contacts and flex cables are very prone to just corroding through and through.

Soft-bricked SM-P900 stucks on system.img in Odin

Hello. Sorry for my enlgish.
Theres a soft-bricked SM-P900, I can normally open download mode. (asking for Kies)
Here's the Odin log:
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
It's always stucks on "system.img" in ANY .tar I try to flash.
Yesterday, it could power on. But now it's not powering on at all. I hope this is because of battery charge.
===UPD: Yes, it was because of battery charge. Now it's powered on.
What should I do, guys? Help, please!
V01DY said:
Hello. Sorry for my enlgish.
Theres a soft-bricked SM-P900, I can normally open download mode. (asking for Kies)
Here's the Odin log:
It's always stucks on "system.img" in ANY .tar I try to flash.
Yesterday, it could power on. But now it's not powering on at all. I hope this is because of battery charge.
===UPD: Yes, it was because of battery charge. Now it's powered on.
What should I do, guys? Help, please!
Click to expand...
Click to collapse
If it were me I would verify the files, perhaps redownload it. I'd also try a different USB port, cable or reinstall USB drivers on the computer. Sometimes one has to clean out old device drivers manually. I've done this with USBDEVIEW.
Sent from my SM-P900 using Tapatalk

Data recovery after Water Damage

My Galaxy S6 recently took a dip in a lake and would not turn on. After trying to displace the water with 91% isopropyl alcohol and I tried to power on again, but no LEDs and would not bootup still. I disassembled the phone and tried cleaning the board with a toothbrush and alcohol to clean any corrosion and hope that my attempts to turn it on did not permanently damage any components. After the cleaning the LEDs turn on, but the screen seems to be damaged beyond repair.
At this point salvaging the phone is not a priority, some very important and irreplaceable pictures that were not yet backed-up are my only concern. Another XDA user suggested trying to install a custom recovery but ODIN keeps failing. I cannot tell you what the S6 screen is showing of course, even putting it into download mode is a bit of a chore.
I am trying to install TWRP on a SM-G920P with ODIN 3.10.7
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have also tried other versions of TWRP and ODIN, all have the same error.
Thanks in advance
Did you by chance have USB debugging enabled? If so, boot phone normally, and use 'adb pull' commands to retrieve what you want.
Sent from my SM-G920W8 using Tapatalk
DarryDoo said:
Did you by chance have USB debugging enabled? If so, boot phone normally, and use 'adb pull' commands to retrieve what you want.
Sent from my SM-G920W8 using Tapatalk
Click to expand...
Click to collapse
Sorry, forgot to mention that debugging has not been enabled. Is there anyway to force USB debugging?

Categories

Resources