Hey there xdadevs, newbie here. I'll try to keep this as detailed and to the point as possible.
Problem
So I've got a Cincy Bell XT720, and I've gotten it properly SIM unlocked and rooted. I'll go to search for networks, consistently pick up Wind Home, and then attempt to connect to it. I'll select Wind Home, and immediately get a notification that says that "Selected network (WIND Home) unavailable", but it'll continue to try to connect to Wind Home. 1-2 minutes later, I'll get a message saying that "Your SIM card does not allow a connection to this network".
What I've Done to Try and Fix It
- Configure APN settings properly
- Reseat SIM Card
- Load Cincy Bell Stock 2.1/Dexter Froyo 2.2/XDA Special RC1 ROMs
- Attempt everything mentioned in this thread here: (http://forum.xda-developers.com/showthread.php?t=974375)
What I think the Problem Is
- Radio/ROM config problem? Can't pinpoint it for the life of me.
- I KNOW it's not a hardware incompatibility problem, if that's a starting point. This is the Milestone XT720 and not the Motoroi, fully capable of supporting the HSDPA 1700/2100 bands that WIND Mobile uses for its 3G networks.
Any help I could get would be greatly appreciated. Right now, my only fallback is this horrid Huawei U1250...it works, but that's like saying that ramen noodles "works" in comparison to a banquet burger with fries. Thanks a ton in advance guys.
Lol, I'm using a CB XT720 on WIND as well, pretty cool. But yeah, mine is working without any issues. Go into a WIND store, show them your issue, and they should be able to replace the sim card. As mentioned in another thread, WIND had some issues with certain sim cards so that may be why your having the connection problems. If that doesn't help, then it's probably something to do with the phone itself.
tharan.a said:
Lol, I'm using a CB XT720 on WIND as well, pretty cool. But yeah, mine is working without any issues. Go into a WIND store, show them your issue, and they should be able to replace the sim card. As mentioned in another thread, WIND had some issues with certain sim cards so that may be why your having the connection problems. If that doesn't help, then it's probably something to do with the phone itself.
Click to expand...
Click to collapse
At least I know that the CB XT720 does work for sure...I can get WIND to check it out (the SIM was ordered back in December or so last year) or even get the phone replaced via Moto warranty if needs be (somehow, still warrantied until March next year). Thanks for the help!
my XT720 is from sigapore and i'm using it on WIND without any issues
using Dexter's froyo ROM
make sure you get the BLACK version of the SIM card, the WHITE SIM cards dies very often
i've replaced both of mines already, they died on their own, both on my Nexus S and XT720
other friends that i've on WIND also had the same problem, with other phones, they also had the WHITE SIM card
just show them the problem, they will change the SIM card for you.
oh! but you need to go to the Corporate WIND stores, not the resellers stores
AllGamer said:
my XT720 is from sigapore and i'm using it on WIND without any issues
using Dexter's froyo ROM
make sure you get the BLACK version of the SIM card, the WHITE SIM cards dies very often
i've replaced both of mines already, they died on their own, both on my Nexus S and XT720
other friends that i've on WIND also had the same problem, with other phones, they also had the WHITE SIM card
just show them the problem, they will change the SIM card for you.
oh! but you need to go to the Corporate WIND stores, not the resellers stores
Click to expand...
Click to collapse
Alright...I'm pretty sure I have the black one (black w/ white trim), but it wouldn't hurt to get a replacement. This one's been in a bricked G1, another G1 that got caught in a torrential thunderstorm (you can tell I don't have good luck with those things), a Huawei U1719, and a Huawei U1250. It's probably just got some age on it by now...flaky with my U1250 anyhow, random (relatively frequent) disconnecting, wouldn't connect the first couple of times, etc. Thanks again, be sure to let you guys know how it goes. =.=
Meh, still got a problem. Tried another SIM, went over to WIND...no such luck. I was told that although the phone may be SIM unlocked and it can see the networks on the 1700/2100 band, the radio's firmware may be locked to prevent a connection (the employee had a similar problem with another phone for Bell). Is there anyone on here who can hook me up with an unlocked radio or a WIND Mobile ROM that could help with this? O-^
Hmmm, strange because I was able to connect to WIND Home on the stock CB 2.1 ROM, Khals MIUI ROM, and Mz's CM6 as well. Perhaps, something is wrong with your baseband? I would try this, if possible, get a friend's sim card (anything but WIND/Mobilicity) and see if you connect to that network whether it be Rogers, Telus, etc. If it can connect, then the phone is able to latch onto the regular GSM frequencies. With regards to an unlock radio or baseband, I'm not sure how thats done but maybe someone else on the forum can help you with that.
For some reason, I'll pop in my Rogers SIM (account was probably deactivated though), and my Moto says:
Emergency calls only
ROGERS
Emergency calls only
Go to check my available networks and..."WIND" is the only one that comes up? No idea as to whether its Home/Away or 2G/3G...just "WIND". Not as if it'll let me connect or anything anyways, same flop as the previous attempts ("Your SIM card does not allow a connection to this network"). :/
http://forum.xda-developers.com/showpost.php?p=10001234&postcount=34 - AHA! Videotron and WIND use the same bands (1700/2100), and some digging around turned that up. Looks like they've been having problems too. Can anyone help pinpoint their radio for me? It seems like that might just do the trick.
Update:
http://forum.xda-developers.com/showthread.php?t=944258#11176044 <- Can someone confirm that this is safe for the XT720? If so, my gut instinct's pretty sure this is exactly what I need...the "freq_F_CN_026-850-2100-signed.zip" one appears to be for Canada, while "freq_F_US_342_107-850-1700-2100-signed.zip" does the frequencies right. O-^
Mann, all I had to do was pop in my sim card and off I went. I think there was a 3G fix around here somewhere, make sure to get someone's "approval" first (one of the more experienced guys) because it may damage your phone. Try this though...
Dial *#*#4636#*#*, go into phone information, and see if anything looks off.
As for frequencies, the country does not matter, the frequencies do...for WIND, you need 1700/2100.
do not use those Defy fixes, it'll probably kill your XT720
RyanGDI said:
http://forum.xda-developers.com/showpost.php?p=10001234&postcount=34 - AHA! Videotron and WIND use the same bands (1700/2100), and some digging around turned that up. Looks like they've been having problems too. Can anyone help pinpoint their radio for me? It seems like that might just do the trick.
Update:
http://forum.xda-developers.com/showthread.php?t=944258#11176044 <- Can someone confirm that this is safe for the XT720? If so, my gut instinct's pretty sure this is exactly what I need...the "freq_F_CN_026-850-2100-signed.zip" one appears to be for Canada, while "freq_F_US_342_107-850-1700-2100-signed.zip" does the frequencies right. O-^
Click to expand...
Click to collapse
Whew, alright. Good thing I asked first, thanks. I still can't get it to work properly...I'm more than likely going to have to ditch this thing and go with a G1 or a Touch Pro 2 if I don't have any better luck with it. Thanks for all the help though guys. :/
Have you flashed a sbf? If so, which one? If not did you buy this phone from Wind or somewhere else? If it is a baseband software problem, then perhaps flashing a different sbf will help (Maybe one of the North American ones-- CBW or brightpoint).
Mioze7Ae said:
Have you flashed a sbf? If so, which one? If not did you buy this phone from Wind or somewhere else? If it is a baseband software problem, then perhaps flashing a different sbf will help (Maybe one of the North American ones-- CBW or brightpoint).
Click to expand...
Click to collapse
STR_U2_04.1E.1_SIGNED_USASHLSTAB14P2XAPCNCBW039.0R_NACBW_P011_A006_HWp3_1FF (Cincinnati Bell)...that's the only .sbf that I can get RSDLite to recognize for some reason. Attempting to pull up one for the UK or the US Brightpoint for example leaves the File Properties section blank and my start button disabled. I have version 4.5.3, if that's any help. Any hope of a miracle here?
Also, I bought it from a third-party in the US...didn't know what carrier it was with, but after some digging around and checking the "S/W" I found it to be Cincinnati Bell. Ideally I'd be looking for a WIND sbf, but I don't think anyone here's managed to get their hands on one. I'm almost at the point of just trying to take it apart to see if there's something loose in the hardware. Someone else on here was saying that there was a loose cable or somewhat that was preventing their UMTS from working properly (can't find the link). Everyone's saying it should be working just fine, I can't really see any alternative besides the baseband perhaps being flaky.
RyanGDI said:
STR_U2_04.1E.1_SIGNED_USASHLSTAB14P2XAPCNCBW039.0R_NACBW_P011_A006_HWp3_1FF (Cincinnati Bell)...that's the only .sbf that I can get RSDLite to recognize for some reason. Attempting to pull up one for the UK or the US Brightpoint for example leaves the File Properties section blank and my start button disabled. I have version 4.5.3, if that's any help. Any hope of a miracle here?
Click to expand...
Click to collapse
Yup, that's the Cincinnati Bell sbf. The brightpoint one is essentially identical but unbranded--the only differences are things like default webpage in the browser and preloaded bookmarks, etc. I don't know a lot about basebands, but I do know the only way to change the baseband firmware currently is with sbf. I think yours is fine, though. AllGamer is our resident WIND expert, so if his advice didn't help, I'm afraid I don't have much more to offer.
Actually, if this is a Cincinnaiti Bell phone, maybe it's SIM locked to CBW...? I know both of mine are. Does anyone know how to test that? SIM locks are also black magick to me.
Yup, that's the Cincinnati Bell sbf. The brightpoint one is essentially identical but unbranded--the only differences are things like default webpage in the browser and preloaded bookmarks, etc. I don't know a lot about basebands, but I do know the only way to change the baseband firmware currently is with sbf. I think yours is fine, though. AllGamer is our resident WIND expert, so if his advice didn't help, I'm afraid I don't have much more to offer.
Actually, if this is a Cincinnaiti Bell phone, maybe it's SIM locked to CBW...? I know both of mine are. Does anyone know how to test that? SIM locks are also black magick to me.
Click to expand...
Click to collapse
Already removed the SIM lock (got that taken care of well beforehand)...I guess I'm on my own then.Thanks everyone, I appreciate the help regardless. :3
RyanGDI said:
Already removed the SIM lock (got that taken care of well beforehand)...I guess I'm on my own then.Thanks everyone, I appreciate the help regardless. :3
Click to expand...
Click to collapse
i have a hunch you are still SIM locked, that error message ("Your SIM card does not allow a connection to this network") you keep having, kinda of suggest that
an easy way to find out, is to see if anyone have an extra unused Cinncinaty Bell's SIM card, and send it to you, so you can pop it in, and if it doesn't give you any error message, but "R"oaming, then that is a good dead indicator that the phone was not properly unlocked.
also in regards to the stock ROMs
you should have no problem flashing any of the .sbf files
my phone was originally an Asian one, then i flashed it to use the UK ROM, and after that i flashed the Dexter 2.2 to it
So are you saying that its possible that an unlock code can "unlock" the device (pass the unlock code request) and allow it to accept a foreign SIM, but still fail to allow it to connect to the SIM's networks? It'd make perfect sense if Rogers was an affiliated network with Cincinnati Bell (for roaming), since it'd be "mutual ground" between WIND and CBW. And then the SIM wouldn't be able to connect to WIND's exclusive 3G network since it was never on the "allowed" networks as defined by Cincy? =.=
if you are in Toronto, i'll suggest you go to P-mall, any of those cell phone stores there can help you unlock the phone for sure
or you can try your luck online with different ways to unlock the phone
quite sincerely we never really talked much about SIM unlocking of this phone within this forum.
perhaps a DEV might be able to help you figure out how to unlock it for free
because if you go to the malls they might charge you an unlocking fee regardless
although with the chinese places you can argue it didn't work, and they will not charge you for the unlocking
Related
Hi, I am sort of new here but I know enough to get around on what I need to do, but I am at a stand still...
I bought a US Cellular Touch Pro 2 from Ebay which was "unlocked" supposedly, but my ATT phone card does nothing in it, I can get digital roaming but ATT will not work on the phone.
So my question is, what are the needed steps in order to get my Touch Pro 2 to get working on the ATT network. As far as I know the Security is not unlocked.
Thanks ahead of time,
if you need any other information please ask =D
-Cyanide
Note: I bought an unlock code from Ebay earlier, but since it says its unlocked I cant use the code, unless there is another way to use that code.
if im right and some1 here can correct me if im not. i think u have to sim unlock it for it to work.
My US Cell TP2 came SIM unlocked
Same as above, my us cell tp2 came sim unlocked also
I just got one from ebay, and I had to security unlock it and install appropriate radio to get it working on at&t
Will any of the GSM labeled AT&T work or is there one that's best?
forum.xda-developers.com/showthread.php?t=549939
will it work with umts 850????
do you know if someone got it working????
I just bought three of these off ebay that were 'unlocked'
yes it says 'your phone is sim unlocked' in the security tab but my ATT cards are not working
someone mentioned adding software or something. can someone please show me how to do this asap. we kinda counted on having the phones today.
i bought a us cellular on ebay as well. had to security unlock it. Got code from this site and then bought from olipro. this should help.
http://rhodiumw.htc-unlocks.com/
http://pocketnow.com/tweaks-hacks/unlock-the-sprint-touch-pro2-radio-to-get-us-gsm
the first one you have to but then the second link you need to watch to get the imei number before you buy unlock stuff. hope this helps. trin to give back what i learned.
There are two different kinds of SIM Unlocks
There is the stock SIM unlock which allows you to use the sim card for other countries. You click on settings, and sim management and it says the sim is unlocked. However, that does not mean that you can use it with ATT or TMobile here in the united states. Reboot your phone and you will most likely see that your radio says something like 2.10.00WF The WF is what is screwin you over with ATT. You need to pay for and use the SIM unlock from Olipro, (there are tons of links already for it.) and unlock the phone. Then put a WU radio on it. I find that the best one that works for USCC is the 1.96.10WU Radio. It has the least amount of DATA crashes. Hope that helps ya out a bit.
jmy72 said:
There is the stock SIM unlock which allows you to use the sim card for other countries. You click on settings, and sim management and it says the sim is unlocked. However, that does not mean that you can use it with ATT or TMobile here in the united states. Reboot your phone and you will most likely see that your radio says something like 2.10.00WF The WF is what is screwin you over with ATT. You need to pay for and use the SIM unlock from Olipro, (there are tons of links already for it.) and unlock the phone. Then put a WU radio on it. I find that the best one that works for USCC is the 1.96.10WU Radio. It has the least amount of DATA crashes. Hope that helps ya out a bit.
Click to expand...
Click to collapse
weird. olinex recomended the 2.32.00wu radio over all the others. but seeing as how my data connection never wants to stay open, maybe i will give that one a try.
Ok so i got the paid unlocking tool and ran it. it appears to have worked.
I then went to this link
http://forum.xda-developers.com/showthread.php?t=578659
and installed both the us cellular and sprint (the first and fourth link).
was that a mistake?
Anyway it doesnt say att when i put in a non active sim card.
is it still ready to use? also when i install the radios should it be in global or gsm mode or does it matter?
nx_2000 said:
will any of the gsm labeled at&t work or is there one that's best?
Forum.xda-developers.com/showthread.php?t=549939
Click to expand...
Click to collapse
Do not install any of those GSM radios to any CDMA phone!!!!!
You will BRICK IT!!!!1
I got a US Cellular HTC TP2 phone too don't use those ****ing radios!
DaveNavy said:
The US Cellular Version on the TP2 is a CDMA AND GSM PHONE you can flash other ROMS than just CDMA this pork chop has no clue what he is talking about.
Click to expand...
Click to collapse
ummm, this is acdma phone with just a extra gsm radio so you can only flash CDMA roms
Wrong??!!! WTF! A troll in this forum?
DaveNavy said:
The US Cellular Version on the TP2 is a CDMA AND GSM PHONE you can flash other ROMS than just CDMA this pork chop has no clue what he is talking about.
Click to expand...
Click to collapse
YOU SHOULD BE BANNED FOR TROLLING AND MAKING FALSE STATEMENTS! YOU DON'T KNOW WHAT YOU'RE TALKING ABOUT!...
Why don't you go ahead buy a CDMA TP2 phone and flash a GSM radio or ROM, go ahead. And make someone record your face and the device. Let's see how you enjoy turning a working phone into a black death piece of hardware that will not respond or do anything.
You better delete your post before someone that doesn't know any better follow your misguided advice and brick their phone!
@DaveNavy,
Read up a bit on this device before advising people. Flashing a GSM rom on a native CDMA device (RhodiumW) is the best and fastest way to end up with a brick. Please make sure about these things before you post anything like this again.
@ all,
Please stop the flaming right here.
egzthunder1 said:
@DaveNavy,
Read up a bit on this device before advising people. Flashing a GSM rom on a native CDMA device (RhodiumW) is the best and fastest way to end up with a brick. Please make sure about these things before you post anything like this again.
@ all,
Please stop the flaming right here.
Click to expand...
Click to collapse
I dont think I was flaming. I wa just correcting his mistake
How long did it take after you paid to get the download link?
Works great using windows 7. I am running Att with data smooth now.
Hey everyone, I am a Galaxy Nexus user but my brother got an old Roger's S2 LTE that he wants to put on a non-Rogers network (same one I am on with my GNex). However we are having a weird issue where if we insert the original (deactivated) SIM that came with the phone it detects it. But if we put in either mine or his own it just always says "No SIM Card". I even have a pay as you go AT&T SIM that wont work in it either. So far I have flashed CyanogenMod and tried the UCLF6 radio as well as the Rogers ICS Radio UXLF3 from this thread http://forum.xda-developers.com/showthread.php?t=1754473
I should note that when my brother originally inserted his SIM he got the unlock screen and paid to unlock it through cellunlocker.net and it was recognizing his SIM at that point. Since then however we have had no luck. He even replaced the SIM card board with a new one.
Any ideas? I am leaning towards hardware issue but its odd that it still reads the original inserted SIM
did you try to go back to stock firmware and see what happened
Yep. I'm pretty sure its hardware. I got it to read again but still no signal. I have it reading my AT&T card now but again still no signal.
In fact even without a SIM card in if I search for Network Operators nothing comes up. If I do the same on my GNex I get a listing so its looking like this phone is no good
EDIT: Just realized who responded. Your threads were VERY helpful for me! Thanks so much... I'm still not convinced the phone is toast... I have a friend with a GNex on Rogers (I'm on MTS) so I will see if I can borrow his SIM and see what happens
WoodroweBones said:
Yep. I'm pretty sure its hardware. I got it to read again but still no signal. I have it reading my AT&T card now but again still no signal.
In fact even without a SIM card in if I search for Network Operators nothing comes up. If I do the same on my GNex I get a listing so its looking like this phone is no good
EDIT: Just realized who responded. Your threads were VERY helpful for me! Thanks so much... I'm still not convinced the phone is toast... I have a friend with a GNex on Rogers (I'm on MTS) so I will see if I can borrow his SIM and see what happens
Click to expand...
Click to collapse
agree, not the phone, the only way to make sure of anything is to restore to stock and do all the testing from that point on
edit: dah, its the radio, what freq is the new sim card on that wont work, is it the same as T-Mobile
edit: maybe not radio, think its like rogers, could be network settings
Actually both MTS and Rogers use the same towers so the phone should be set properly.
I've got it reading my MTS SIM now but cant pick up any networks. Its set to LTE/HSPA/GSM (Auto) and MTS is HSPA.
Is there anything that could be done to the IMEI of the phone to sort of "blacklist" it from working on any network?
Here is where I have tested from so far:
Stock before I did anything to the phone (Stock rogers GB)
CM9 Nightly
Stock Rogers ICS
SkyICS
I have also tried both the lastest AT&T Radio as well as the latest Rogers Radio. With my GNex both myself and my friend on Rogers use the same Radio (UGLC1).
At this point it seems either the radios arent working at all or the phone is blocked somehow
EDIT: Info on the MTS network... Found on the FAQ on their site:
Any unlocked devices (i.e. devices that are not tied to a specific carrier) will work with MTS SIM cards (on the MTS 4G network). However, carriers such as Rogers, Bell and Telus lock their devices to work with only their SIM cards and these devices will not work with a MTS SIM card. Similarly, MTS intends to lock our devices to our SIM cards. Therefore, our devices will not be usable on another carrier's network.
Please note that any unlocked device must support 4G North American Frequencies (850Mhz), older GSM devices will not function on our new 4G network. You can find out if your device is 4G compliant by reviewing the phone's settings.
Click to expand...
Click to collapse
Also this link: http://www.howardforums.com/showthread.php/1711666-MTS-4G-frequency
UGLC1 never seen that radio for the skyrocket
edit: oh, for the gnex
did you try the *#2263# menu
Yes when I try that menu (*#2263#) it doesnt do anything. I can do *#*#4636#*#* when on CM9 and it works but on stock and SkyICS it just FCs when I select "Phone Information"...
I am going back to Rogers Stock ICS right now. Gotta head off to my engagement party but will likely be back at it tomorrow
shouldn't forceclose, redl and try reflashing x2 the rogers radio, wipe/format x3 in cwm b4 going back to stock ics
Will do first thing tomorrow (or tonight if I'm still in any shape to do so )
If anyone reading this thread has a stock Rogers phone can you turn it off, take out your SIM and then boot it up without a SIM in it and then do a Network Search and see if anything comes up? On my GNex I get networks but on the S2 LTE I dont. In fact I have never seen any signal from any network on this phone yet with an MTS, AT&T and an old Rogers SIM
EDIT: Actually you will probably have to be on CM9. With stock you cant get to the Network Operator section without a SIM card inserted but in CM9 you can
vincom said:
shouldn't forceclose, redl and try reflashing x2 the rogers radio, wipe/format x3 in cwm b4 going back to stock ics
Click to expand...
Click to collapse
Ok I had enough time to do as you suggested above. Wiped like crazy then went back to stock using the ODIN method and the firmware from sammobile.
Actually I figured it out... it only FCs when I have the AT&T SIM card in and I think thats because AT&T is RAT Locked? If I have no SIM in I can get to all the menus.
k, try to set the freq(play around with it) in that menu w/out sim, then shutdown and install sim b4 restarting, left haptic to click "end" is saving
Got home and went right to work. Almost positive the problem is the radio not working now. I managed to get both SIMs reading without issue but neither will get signal of any sort (even straight after stock reflash). Gonna call it for now until I get a hold of my buddys Rogers SIM.
Thanks so much for all the help, I really appreciate it!
After much research, and scouring this forum (which Id like to note is fantastic) - i am hitting a brick wall and at my wits end with my Doctors phone. (Doing him a favor)
Here's the preface. He purchased (off ebay) a "presumed" unlocked Rogers Galaxy S2 SGH-i727, and wishes to use his existing Straight Talk Sim card with it. The Sim is confirmed working in his previous older Samsung cell, which i also have, without fail.
He gave the GS2 to me claiming it wouldn't read the Sim, and i thought, agh just needs a root and rom, and maybe some radio switching. And boy am I humbled. This thing will not read a Sim if its life depended on it. Before I rule out a beat phone hardware issue, id like to see if anyone else could just advise me of some things.
1 How would I confirm this phone is indeed unlocked from Rogers, and if it wasn't would that cause a no Sim read issue?
2 To make this go from work from Rogers to Straight Talk, is their a ROM, Kernel, Radio, Band known to do the job?
At this point I've used Sk8's CWTouch for Recovery and it works great, current ROM i tried is a TMobile one (Juggernaught 5.0), Stock Rogers/ATT Radio, and i believe the Rogers Kernel as well.
Any help on this mess i've gotten myself into would be sincerely appreciated. Many Thanks!
theProjectLLC said:
After much research, and scouring this forum (which Id like to note is fantastic) - i am hitting a brick wall and at my wits end with my Doctors phone. (Doing him a favor)
Here's the preface. He purchased (off ebay) a "presumed" unlocked Rogers Galaxy S2 SGH-i727, and wishes to use his existing Straight Talk Sim card with it. The Sim is confirmed working in his previous older Samsung cell, which i also have, without fail.
He gave the GS2 to me claiming it wouldn't read the Sim, and i thought, agh just needs a root and rom, and maybe some radio switching. And boy am I humbled. This thing will not read a Sim if its life depended on it. Before I rule out a beat phone hardware issue, id like to see if anyone else could just advise me of some things.
1 How would I confirm this phone is indeed unlocked from Rogers, and if it wasn't would that cause a no Sim read issue?
2 To make this go from work from Rogers to Straight Talk, is their a ROM, Kernel, Radio, Band known to do the job?
At this point I've used Sk8's CWTouch for Recovery and it works great, current ROM i tried is a TMobile one (Juggernaught 5.0), Stock Rogers/ATT Radio, and i believe the Rogers Kernel as well.
Any help on this mess i've gotten myself into would be sincerely appreciated. Many Thanks!
Click to expand...
Click to collapse
under the battery does it say "i727r", if no "r" at the end its not a rogers phone.
if there is a "r" try a rogers sim card and pure stock firmware .
if no "r" try a att sim card on stock firmware
yes, there is definitely an "r" making it a rogers phone, being in the US, i have no access to test a Rogers sim, but also this needing to work on straight talk is the mission, otherwise i believe he may have to pursue another route unfortunately thanks so much
bah does the thanks button disappear after you reply to someone? apologies
theProjectLLC said:
yes, there is definitely an "r" making it a rogers phone, being in the US, i have no access to test a Rogers sim, but also this needing to work on straight talk is the mission, otherwise i believe he may have to pursue another route unfortunately thanks so much
Click to expand...
Click to collapse
that was to check for a hardware failure for the sim card tray, you need to know before you can diagnose further, do a att stock restore then try a att sim card and see whay happens, nothing to lose
Vincom's suggestion is to rule out an actual hardware issue. On the other hand a non Rogers SIM should either work if it's unlocked or pop up the unlock dialog. Suggest trying an AT&T SIM since that's the closest to a Rogers. I have no idea about Straight Talk.
I'm not sure if I'm going to find an answer to this question since there are at most a dozen Photon Q's being used with Bell Mobility up in Canada, but you never know until you ask right?
Just got CM 10.1.3-RC2 (Android 4.2.2) up on my phone, and it's working great with one exception: I'm not being notified when a voicemail message is waiting for me.
I've been looking around and haven't seen anyone else posing this question in relation to the Photon Q, though there have been a few other post around for other phones. However, the suggested answers seem to vary by phone: the HTC Desire Z supposedly needs a radio update, many phones (all?) had issues with CM7, the Inspire 4G apparently needs a bit of specific code., etc...
Does anyone have a solution to this for the Photon Q?
I would love to know how you managed to get Bell's service on your phone, as it doesnt show up properly in their MEID database and they cant give me a straight answer before I use my credit card.
adrienspawn said:
I would love to know how you managed to get Bell's service on your phone, as it doesnt show up properly in their MEID database and they cant give me a straight answer before I use my credit card.
Click to expand...
Click to collapse
Hey unfortunately I never got this sorted out. I'm now running 4.3 and still having the same problem. For me it's not too much of an issue as people rarely seem to make phone calls these days, but I just kind of check my voicemail manually every few days just to be safe.
But you still have voice/text working? I tried bringing it to a Bell store today and they couldn't activate it without a certain hexadecimal 11-key number that's unique to the device.
adrienspawn said:
But you still have voice/text working? I tried bringing it to a Bell store today and they couldn't activate it without a certain hexadecimal 11-key number that's unique to the device.
Click to expand...
Click to collapse
I do have voice, text, and all the other stuff working just fine. I didn't even talk to Bell about "activating" my device, I just took the sim card out of my old phone and put it in the new one, and voila. However, I believe it depends what rom you're running... I'm using CyanogenMod and I believe they include some specific settings to get the phone up on various carriers.
Sorry if this is an obvious question, but you've done the hardware mod needed to use a Canadian (or other) SIM card right?
Basically everything I did I found in a single thread: http://forum.xda-developers.com/showthread.php?t=1929143 It's a long one but chances are you'll find what you need to know somewhere in there!
Ah, I thought you were using their CDMA network. Trying that route before having someone do the mod for me. I'm thinking the key might be the MIN.
Hello,
I bought my HTC Sensation about a year ago on Ebay. The seller claimed the phone was purchased outright and paid off. I checked the imei and it showed clean. When I got it, I popped my Airfire sim card into it and it worked fine. A month ago, I switched to Cricket as Airfire was going out of business. Cricket made me enter my imei. It said it was bad. I called T-Mobile and they said the seller defaulted on payments. They refused to help in any way. They told me to buy the phone direct from them next time. I told them I had proof I was buying it in good faith. They didn't care and apparently have no problem punishing the victim.
Anyways, when I got my Cricket sim and popped it in, my phone said I was roaming. It has said I was roaming for a full month now. I can send and receive calls, but my data is stuck at EDGE and some of the programs don't work since the phone thinks its roaming. I need to have "data roaming" enabled for data to work. Cricket ran some tests and eventually said I needed to do a factory reset.
So, I switched from the Android Revolution rom to the ViperS 5.2.1 rom. I did a full dalvik and cache wipe and reformatted everything but the sd card. I installed the new rom and kernal. Same thing. Phone still says I am roaming. Odd thing is, when I go to manually select carrier, my options are Cricket (current carrier), Airfire (previous carrier) and TMobile (stock carrier). Also, when I am using data, it has an "E" above the data. E is what Airfire used. Is there somehow somewhere a place that the phone is storing info through wipes?
I am s-off, rooted and debranded. I sim unlocked the phone myself. I am so stuck and think that only one of the geniuses on XDA are my only hope. I have went mental spending hours and hours on this. Some XDA peeps are smarted than HTC and Cricket combined, so please help me out here.
Thanks,
Grant
SuperGrant said:
Hello,
Thanks,
Grant
Click to expand...
Click to collapse
Hi grant, this is a very odd situation your in. With my sensation when I leave the UK and connect to another EU "partner network" is the only time my phone would jump into roaming mode. Is it possible that cricket is not directly supported in your area? Maybe they rent their local connection from another carrier and thats why your getting connected as roaming? Have you tried any other sim cards to see if they come up as roaming?
Sent from my HTC Desire S using Tapatalk
Hi heavy_metal_man
I am quite sure that At&t is Cricket's parent company so all of the towers should be At&t's networks. Also, I have checked it when in other cities and I get the same message, though I haven't traveled more than 30 miles away.
The previous sim with AirFire worked fine. I also popped out the sim for Cricket and put it in my mom's phone to see if it was the sim. Her's worked fine. She got the automatic Cricket update settings right away and was not roaming. Mine never got the Cricket pop-up so I had to manually enter all of the data info. Yes, odd indeed and I am lost.
SuperGrant said:
I am quite sure that At&t is Cricket's parent company so all of the towers should be At&t's networks. Also, I have checked it when in other cities and I get the same message, though I haven't traveled more than 30 miles away.
The previous sim with AirFire worked fine. I also popped out the sim for Cricket and put it in my mom's phone to see if it was the sim. Her's worked fine. She got the automatic Cricket update settings right away and was not roaming. Mine never got the Cricket pop-up so I had to manually enter all of the data info. Yes, odd indeed and I am lost.
Click to expand...
Click to collapse
OK, the info your adding manually, is that the same info as is registered when the card is in your mums phone? Same APN etc?
Sent from my HTC Sensation using Tapatalk
heavy_metal_man said:
OK, the info your adding manually, is that the same info as is registered when the card is in your mums phone? Same APN etc?
Hi heavy_metal_man. Yup. Same info. Only difference is that the info all loads automatically on hers. I do get automated texts from Cricket when I put the sim in my phone as did she, but I had to get the APN info from Cricket the first time because it didn't auto load. I am still wondering if it is a sim issue, but I expected my mom's phone to be roaming when I put the sim in hers. I was shocked when it wasn't. She just has a free stock phone from Airfire btw. Nothing fancy and nothing done to it.
Click to expand...
Click to collapse
SuperGrant said:
heavy_metal_man said:
OK, the info your adding manually, is that the same info as is registered when the card is in your mums phone? Same APN etc?
Click to expand...
Click to collapse
Hi heavy_metal_man. Yup. Same info. Only difference is that the info all loads automatically on hers. I do get automated texts from Cricket when I put the sim in my phone as did she, but I had to get the APN info from Cricket the first time because it didn't auto load. I am still wondering if it is a sim issue, but I expected my mom's phone to be roaming when I put the sim in hers. I was shocked when it wasn't. She just has a free stock phone from Airfire btw. Nothing fancy and nothing done to it.
Click to expand...
Click to collapse
Hmm. Are those 3 carriers the only ones available to you? I think the imei may be key here, if cricket know its a T-Mobile phone they may register that you are roaming. I think your previous carrier (airfire) was a Virtual mobile network, much like giffgaff in the UK ( which runs on the o2 network.) As such they may not have inforced the same imei policy's that cricket does. But this is just a hunch as I am on UK networks and we do things much differently. If you could ask about any friends and colleges that have different carrier simcards from our previous 3 you could gauge what carriers your phone is compatible with.
Worst case scenario you could maybe buy another broken htc sensation and perform a motherboard swap. This would solve your imei issue, assuming that it was the primary issue. But check the simcards first and report back
Sent from my Nexus 7 using Tapatalk
heavy_metal_man said:
Hmm. Are those 3 carriers the only ones available to you? I think the imei may be key here, if cricket know its a T-Mobile phone they may register that you are roaming. I think your previous carrier (airfire) was a Virtual mobile network, much like giffgaff in the UK ( which runs on the o2 network.) As such they may not have inforced the same imei policy's that cricket does. But this is just a hunch as I am on UK networks and we do things much differently. If you could ask about any friends and colleges that have different carrier simcards from our previous 3 you could gauge what carriers your phone is compatible with.
Worst case scenario you could maybe buy another broken htc sensation and perform a motherboard swap. This would solve your imei issue, assuming that it was the primary issue. But check the simcards first and report back
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
Hmm... There are only 3 carriers available. Should there be more? It's not tied to the sim? Everyone I know either still has Airfire and plans on switching to Cricket or has cdma so I have been out of luck with trying another sim. The only other thing I thought about was 4ext recovery. No matter what I flash; roms, kernals, firmware or radios, the recovery always survives of course. So, if the previous carriers are surviving the flashes, perhaps there is a place on the phone like the recovery where they are surviving.
SuperGrant said:
Hmm... There are only 3 carriers available. Should there be more? It's not tied to the sim? Everyone I know either still has Airfire and plans on switching to Cricket or has cdma so I have been out of luck with trying another sim. The only other thing I thought about was 4ext recovery. No matter what I flash; roms, kernals, firmware or radios, the recovery always survives of course. So, if the previous carriers are surviving the flashes, perhaps there is a place on the phone like the recovery where they are surviving.
Click to expand...
Click to collapse
Its unlikely to be to do with the recovery, no reason for it to keep anything like that. It's most likely the phones imei at this point, though im unsure as to why this was not an issue for airfire.
Do you know what firmware version you have? Have you flashed 3.33 by yourself?
Sent from my Nexus 7 using Tapatalk
heavy_metal_man said:
Its unlikely to be to do with the recovery, no reason for it to keep anything like that. It's most likely the phones imei at this point, though im unsure as to why this was not an issue for airfire.
Do you know what firmware version you have? Have you flashed 3.33 by yourself?
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
Yup, I flashed 3.33 universal after doing a super Cid. Well, maybe its time to just get a new phone, although I would really like to figure out this problem first. I am not the kind of person who can just drop things, lol.
SuperGrant said:
Yup, I flashed 3.33 universal after doing a super Cid. Well, maybe its time to just get a new phone, although I would really like to figure out this problem first. I am not the kind of person who can just drop things, lol.
Click to expand...
Click to collapse
I know how you feel. Maybe its because they cricket know the sensation 4g is a T-Mobile device and force you into roaming mode by default. I think its possible to overwrite the devices mid and cid, flash a sensation XE rom and effectively have a sensation XE. But such things can be quite dangerous and i couldn't say for definite if it would work to fix your issue :/ (not recommending anyone tries this without proper research and understanding :/)
Can you get access to another cricket sim without a contract? Just for testing?
Sent from my Nexus 7 using Tapatalk
heavy_metal_man said:
I know how you feel. Maybe its because they cricket know the sensation 4g is a T-Mobile device and force you into roaming mode by default. I think its possible to overwrite the devices mid and cid, flash a sensation XE rom and effectively have a sensation XE. But such things can be quite dangerous and i couldn't say for definite if it would work to fix your issue :/ (not recommending anyone tries this without proper research and understanding :/)
Can you get access to another cricket sim without a contract? Just for testing?
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
I believe I have already done that. When I go into info about my phone, it says Sensation XE. It also registers as Sensation XE in the Google play store. I was thinking about telling Cricket to send me a new sim. Otherwise, I have no access to one at this time.
SuperGrant said:
I believe I have already done that. When I go into info about my phone, it says Sensation XE. It also registers as Sensation XE in the Google play store. I was thinking about telling Cricket to send me a new sim. Otherwise, I have no access to one at this time.
Click to expand...
Click to collapse
I think that it would be your best bet, although your device is probably showing up on the play store as an XE because of its build.prop from your custom rom, not any advanced MID changes. although you can check by using the command
Code:
fastboot getvar all
this will show your your mid, cid and your imei among other things.
SuperGrant said:
I believe I have already done that. When I go into info about my phone, it says Sensation XE. It also registers as Sensation XE in the Google play store. I was thinking about telling Cricket to send me a new sim. Otherwise, I have no access to one at this time.
Click to expand...
Click to collapse
I've worked it out! Its a frequency issue. Cricket apparently only support cdma frequency's, while the sensation only uses gsm frequency's. So in order to connect your phone is bunnying onto a local gsm service, which is then redirecting you to cricket. Hence the roaming! If you want off the data roaming you will need to either swap to a different phone carrier or buy a cdma phone
Sent from my Nexus 7 using Tapatalk
Hi heavy_metal_man,
Cricket did use CDMA for most of the time, but they have switched to GSM. They send a sim now and are trying to switch all of their old customers to GSM. What I am having trouble figuring out is what frequencies they use. Perhaps my phone is not quite compatible. I am having trouble with that as well. GSM arena, Phonescoop and the other major sites kind of have different data as far as my phone goes. My phone is called "HTC Sensation 4G" as far as I know. Yet, they list no 4g capability or frequencies. Of course, I believe that would only affect data and I still should not show as roaming.
I have been unable to figure out fastboot since switching to the viper rom. It doesn't use usb mass storage anymore. It uses the new system in which the whole phone is recognized as a storage device by the computer. Forgot what they called it. I wish they hadn't changed it, and apparently Windows 7 should recognize it by default, but it does not. I am sure if I get enough time to put into it I will figure out how to use the fastboot commands again.
I am ready to give up and just get a new phone pretty soon. Would be nice if Cricket's customer service wasn't so worthless. It could still be the IMEI or something on their end that I can do nothing about but they have failed to provide any solution.
SuperGrant said:
Hi heavy_metal_man,
Cricket did use CDMA for most of the time, but they have switched to GSM. They send a sim now and are trying to switch all of their old customers to GSM. What I am having trouble figuring out is what frequencies they use. Perhaps my phone is not quite compatible. I am having trouble with that as well. GSM arena, Phonescoop and the other major sites kind of have different data as far as my phone goes. My phone is called "HTC Sensation 4G" as far as I know. Yet, they list no 4g capability or frequencies. Of course, I believe that would only affect data and I still should not show as roaming.
I have been unable to figure out fastboot since switching to the viper rom. It doesn't use usb mass storage anymore. It uses the new system in which the whole phone is recognized as a storage device by the computer. Forgot what they called it. I wish they hadn't changed it, and apparently Windows 7 should recognize it by default, but it does not. I am sure if I get enough time to put into it I will figure out how to use the fastboot commands again.
I am ready to give up and just get a new phone pretty soon. Would be nice if Cricket's customer service wasn't so worthless. It could still be the IMEI or something on their end that I can do nothing about but they have failed to provide any solution.
Click to expand...
Click to collapse
Sorry for my delayed reply, I noticed that cricket swapped out to gsm and I discovered that their gsm tech is actually supplied at&t as they bought them out.
So I looked at their coverage map for the area airfire operated and I noticed that they had 2 or 3 area that were only providing 3g support via a partner, so I assume that would put you into roaming. It might be worth a look at their map and confirm if you reside on one of these black areas ?
Sent from my HTC Desire S using Tapatalk