How to set up a new G2x.
1. If it needs 2.3.3 do that first.
2. Hard reset the phone...turn phone off, hold volume down and power, for about 10 seconds until the little unpacking icon bubbles up.
3. Start phone up, and what the heck, go into privacy menu and do a complete restore, from there. (Its twice the fun, done via two different start signals, but it won't hurt, the phone is already blank, and it adds 10 minutes max.
4. Download as the first thing the My Device T-mobile app, and install it. Someone did some digging and found that the older version was problematic...and what the heck, it a no harm no foul item even if the guy is wrong and its just placebo. He was doing some sort of checking to see what was causing the faults and it was coming from the OLD my device program.
5. Turn off the phone via the menu.
6. Turn on the phone.
7. Turn off the phone.
8. Do a hard restart (not a hard restore, just restart) With phone off, hold power and volume up, until it comes on, and then blanks, and the white LG screen comes up. You should see it cycle, it may come on like normal, but keep holding until it cycles.
9. Unless you want random reboots or what not....DO NOT INSTALL ANY MEMORY MANAGERS OR TASK KILLERS, or BATTERY SAVERS. If you leave your house...turn off your WIFI. If you are not using the GPS, turn it off. If you are not using data, set the data mode to 2G only or turn it off. Beyond screen brightness those are all the major juice users.
Anything that you give control to shut down "wasteful" processes, is giving that utility to carve out dependent processes, which when your phone finds missing can cause all sorts of errors like rebooting.
Many of the people complaining about reboots (not all) slapped on a copy of advanced task killer, and are dumbfounded when there system becomes unstable.
Your G2x should be OK.....so to speak...now.
Related
Excuse me I'm almost suicidal.
I hold the two keys down that bring up the hardware control panel, I turn off the mobile phone, bluetooth, wifi, and activesync, I open the task manager and stop any active processes, I turn my xda off (at least I think I do) and BEHOLD in just a few short minutes the stinking thing turns itself back on again, and stays on.
My PC informs me it has an activesync connection yet my hardware panel says its turned off, I try move some files around and sure enough I can gain access to my memory card, I run task manager and despite the hardware panel telling me activesync is not working the task manager knows different.
Not only has activestink decided its gonna work even though I've told it not to I HAVE AN INTERNET CONNECTION! , talk about a security risk.
WTF is in control of this pile of junk, me or the hardware/software.
Please tell me there is a fix for this, when I turn something off I expect it to stay turned off (completely) until I turn it back on again.
Now if you don't mind I'm going to lay down and have a nervous break down.
Dude you really need to chill.
These things do require some potions .
I do not know the exec in person but all HTC and most other WM 5 devices shut down completely when you hold the "standby" button for 10 seconds or more. (On the exec i believe it is a small round metal color button on one of the sides.)
levenum said:
Dude you really need to chill.
These things do require some potions .
I do not know the exec in person but all HTC and most other WM 5 devices shut down completely when you hold the "standby" button for 10 seconds or more. (On the exec i believe it is a small round metal color button on one of the sides.)
Click to expand...
Click to collapse
Hi'
Been there, pressed that, still turns itself back on, even tried a factory reset and it still does it.
Probably micro$oft being insane again.
Perhaps buying a device with a Microsoft OS was not the right choice if you think they are insane?
The Universal doesn't have the full off feature as some other devices do, and if you use pushmail solutions, it will sometimes turn itself on if you have the screen open.
It also does this on a few other devices.
Using the device lock option on the doday screen prevents the problem, there may be other fixes by now, but that, or closing the screen are the simplest.
Some other today plugins, I forget the name, will give you an auto lock option when you press the power.
That said though, I use pushmail, and mine doesn't come on that I have noticed, but my Wizard does unless I lock it.
I've got a rooted (Super SU, but the original root manager was Superuser) LG C800 that I was having problems with. To be specific, I installed some apps on to the system. Some of these apps would be Titanium Backup for root, Avast Mobile Security, ROM Tool Box Lite, Super SU, and a quite a few others. From day one they seem to be kicked right back to my S.D. card, but not all at the same time, and some would stay on the system. I read where I should move the apps back to my S.D. card and try to re-install them on the system minus the data. When I did, the phone went nuts. Now it stays in a restart mode but never fully boots up. Can I salvage it, and if so, please tell me how?! I have tried the hard reset/recovery boot where you hold down the power button, volume, and a few other keys, but it did not work. I'm a broke college student and can't really afford to buy a new phone. I used this one for everything including tethering it to get my assignments done at home and turned in on time. Please help! I'm open to suggestions....... My phone will be completely off. When I plug it into my computer, via U.S.B., it automatically turns it on whether I want it to be on or not. Then it starts off in "reboot recovery" mode, will boot all the way to the point to where the home screen would normally turn on, but then it starts in that "boot loop" all over again but never fully boots up before going back to the beginning of that "boot loop" yet again. I can't even get it to register on my laptop as being plugged in. The reason I took the apps I placed on the system off was because sometimes when I'd re-boot the system the apps would be on the system and sometimes back on my S.D. card without my involvement of any kind other than rebooting my phone. Is completing a Nandroid recovery or re-installation of my ROM even possible with my computer no longer recognizing it as even being plugged in? From what I can tell it won't be. Am I fighting a lost cause or is it salvageable?
Rooted myTouch Q 4G, a.k.a. LG C800
I believe it has a 2.3.4 GRJ22-perf, and then something like 2.6.35.7? I can't remember off the top of my head, and I can't pull it up on my phone anymore or else I'd double check.
Have you tried booting into recovery?
(More about my phone from the original post) Honestly.........I'm not what you may consider technologically inclined. I have however done about as much research online concerning this matter as any one person can do. I've looked it up on all major sites, and many smaller ones too, that post remedies for phone, or "human" if you'd rather, malfunctions. They all talk about still being able to reach a home screen or doing the whole holding the power and volume decrease buttons until I "reboot recovery" screen appears (if that's what you're referring to as doing a recovery reboot as). Don't forget the one where you hold hold the power and volume decrease buttons along with the "A" and "F" keys as well. I even tried one from here where you're supposed to push the genius button after the Android figure leaves the screen. My phone won't allow me to do either. Basically if it's online, I myself, or this girl that's been staying with me, have tried it without any results. On the initial boot the Android figure and the box with the arrow coming out of it show up and it boots until just about the point that it use to switch over to the home screen and it will start the whole "boot loop" over again. The thing is though that the Android figure and box aren't there any other time after the first boot, and with every boot loop it makes after that, the time is reduced from the beginning of the loop to the end when it starts all over again. The phone won't shut off unless I remove the battery and even though my laptop no longer recognizes the device, when I plug my phone into it or another power source and it's off, it automatically turns itself on and begins that boot loop all over again. there is one thing I have yet to try. I read on one site where I could download a custom ROM on my S.D. and then try reboot it, but it never makes it to the point in which the files on my S.D. card are ran, much less scanned. I am still 100% open to any and all suggestions in the diagnosis of this issue. I may record and place a video on one of the more popular "tube" sites to better show or further explain what's happening and then come back on here to post the link?! Feel free to reply back if it's possible you can help before I'm able to complete that later this evening. And thanks for any and all help in advance to everyone.
I was using an app on Sunday, when the app froze completely and the screen of the s3 went black. The only thing I could see was the status bar up top, but even that was unresponsive. So I pulled the battery and turned it back on, and it was acting extremely slow so I got impatient and started trying to get into settings, when it went unresponsive again.
This time I held down the power button to see if I could get it to respond and the lock screen came up, without my wallpaper and instead of Verizon Wireless at the top, it said "No Service". After a couple of seconds my wallpaper showed up and then it said Verizon Wireless. After I get through the lock screen, I would go through the same whole routine - e.g. try and get into settings, freeze, hold power, have it come back up, etc. So I battery pulled again.
Finally, I got it to boot OK, by just letting it be for 10 minutes and completely ignoring it.
However, today my battery drain was pretty fast, it was on for 12 hours and was down to 40% after only 30 minutes of screen time. The culprit was "Android System" at 61%, i've never seen this that high before. Because of the high "Android System" power usage, I thought it might be good to power it down. Upon boot up, I assumed I'd be able to use it immediately, so I started going into Settings, and yet again it went unresponsive.
Are the two issues unrelated? What should I do?
As a warning, I'm extremely new to anything smarter than a Nokia brick, so be patient - Thanks!
As inconvenient as it is, I would recommend a full system wipe and go back to out of the box. That seems to fix everything and unfortunately it is rather difficult to diagnose issues on phones, especially unrooted.
In order to do a wipe you can do one of two things, goto settings then backup and reset, then hit factory data reset.
-OR-
Turn off the phone. When you start it again hold volume-up, power, and home to get into recovery. Then do the factory reset.
Ok, I thought that's what my option was. Thanks dwibbles.
Hey everyone who reads this.
I'd like to start my topic with apologising if I post this in the wrong section.
So, I have a LG Spirit H440N LTE for about 3 years now, maybe a little less. I've always taken good care of it, both physically and in updates / security wise aswell.
My phone has been working flawlessly until the last 2 days. 2 days ago i was charging my phone, and when it vibrated (meaning its 100%) I pulled the cable off, and pressed the power button (power button locks - unlocks the screen) the screen didn't turn on. I was like "wow that's strange" but didn't care much, i just kept pressing the button every 5-6 seconds, nothing.
At that point I pulled the battery out, let it sit for a short time and then put it back, start the phone, I felt the vibration (meaning it's starting up) but no screen, so my first idea was that I need to get a new firmware and completely reinstall my phone, as it seems like it got bricked.. for no reason, by itself ? Strange thing but I accepted it and literally been googling for 9 hours now and I find more and more issues.
After I got LG FlashTool, drivers, and even 3 different firmwares, I wanted to start the phone in download mode to start upgrading, but even though I held down "volume up for 5 seconds and then put the usb cable in" nothing happened, no screen, my PC didn't recognise the phone either.
So I got a little bit mad and pulled the cable out from the phone, I wanted to remove the battery, but out of nowhere the phone suddenly started loading in, screen working completely fine, i could do whatever i want, so my first thing was to do a hard reset. After the hard reset I set up my usual stuff (important apps etc) and I locked the screen so my battery won't go down. Little did I know, I ****ed up again, because ever since that happened, I can't get my screen to work again. I tried everything I could but my PC still doesn't recognise the phone (even after a LOT of drivers being installed), charging the phone doesn't do anything. Regardless if I remove - put back the battery no screen, no screen in download - hard reset mode either, it's just completely black.
I'd like to have some sort of help, because I am just completely out of ideas, I really feel like a firmware change could fix the phone, but if the computer doesn't recognise it, I have no idea what to do.
rawon3 said:
Hey everyone who reads this.
I'd like to start my topic with apologising if I post this in the wrong section.
So, I have a LG Spirit H440N LTE for about 3 years now, maybe a little less. I've always taken good care of it, both physically and in updates / security wise aswell.
My phone has been working flawlessly until the last 2 days. 2 days ago i was charging my phone, and when it vibrated (meaning its 100%) I pulled the cable off, and pressed the power button (power button locks - unlocks the screen) the screen didn't turn on. I was like "wow that's strange" but didn't care much, i just kept pressing the button every 5-6 seconds, nothing.
At that point I pulled the battery out, let it sit for a short time and then put it back, start the phone, I felt the vibration (meaning it's starting up) but no screen, so my first idea was that I need to get a new firmware and completely reinstall my phone, as it seems like it got bricked.. for no reason, by itself ? Strange thing but I accepted it and literally been googling for 9 hours now and I find more and more issues.
After I got LG FlashTool, drivers, and even 3 different firmwares, I wanted to start the phone in download mode to start upgrading, but even though I held down "volume up for 5 seconds and then put the usb cable in" nothing happened, no screen, my PC didn't recognise the phone either.
So I got a little bit mad and pulled the cable out from the phone, I wanted to remove the battery, but out of nowhere the phone suddenly started loading in, screen working completely fine, i could do whatever i want, so my first thing was to do a hard reset. After the hard reset I set up my usual stuff (important apps etc) and I locked the screen so my battery won't go down. Little did I know, I ****ed up again, because ever since that happened, I can't get my screen to work again. I tried everything I could but my PC still doesn't recognise the phone (even after a LOT of drivers being installed), charging the phone doesn't do anything. Regardless if I remove - put back the battery no screen, no screen in download - hard reset mode either, it's just completely black.
I'd like to have some sort of help, because I am just completely out of ideas, I really feel like a firmware change could fix the phone, but if the computer doesn't recognise it, I have no idea what to do.
Click to expand...
Click to collapse
You might be having hardware issues, such as a faulty power button. If you are the type of user that frequently presses the power button to lock/unlock the screen, this leads to excessive wear on the button components, this is why some users prefer to use the "tap to sleep" and "tap to wake" feature, to avoid wearing the power button out. On my LG, this feature is called "KnockOn", it's located in Accessibility settings.
Sent from my LGL84VL using Tapatalk
I've been using HTC U11 Plus as my main phone since the day it came out. I absolutely love this phone. In my opinion it's the best phone I've ever had. I never felt the need to get a new phone. I've been gaming, working, etc. and I never had any issue with it.
Two days ago all of a sudden while using my phone it got stuck. None of the button were working and the screen also had response so I pressed and hold the Power button and Volume Down button to boot into recovery mode. So i could clear cache and reboot again but my phone doesn't seem to reboot. It just turns off when I select reboot now. I even tried "Wipe data/factory reset from the Recovery menu options" and then delete all user data option and then Reboot system now to restart your phone. Still no luck. As soon as I press on reboot system my phone just turns off and doesn't reboot or turn on at all.
Even when I put my phone on charging there is not light to indicate that my phone is charging at all.
PLEASE HELP!!!!
Same problem here... Screen flashed white, phone rebooted to encryption screen to enter pin, then powered off... Hasn't been back on since (thins happened in October 2021).
I'm interested in a possible way to get the data off the phone, even if some parts swapping is involved.
PS. I changed the battery thinking it was that, but the phone still isn't coming on or showing the red battery charging light.
I guess it is time for you both to use ADB. When installed properly you should be able to see your phone in device manager on Windows systems. That in itself would be a good starting point. Or just fire up ADB and check if ADB detects your phone. If you are unfamiliar with ADB, Google it.
In ADB use: *.\adb devices* (without the *) If it works properly you should get a return with a device number. You could then flash a boot image or system image or both and see if your phone start's up again.
Hello,
same Issue here.
Solution is to heat up the Phone above 50°C and hold the temperature while it run and copy Data.
I have spend 40h+ to Backup Data and heat up the Phone.
Seems for me to the same problem like the RROD at Xbox360.
Lead-Free solder at the BGA-Chips.