I was using an app on Sunday, when the app froze completely and the screen of the s3 went black. The only thing I could see was the status bar up top, but even that was unresponsive. So I pulled the battery and turned it back on, and it was acting extremely slow so I got impatient and started trying to get into settings, when it went unresponsive again.
This time I held down the power button to see if I could get it to respond and the lock screen came up, without my wallpaper and instead of Verizon Wireless at the top, it said "No Service". After a couple of seconds my wallpaper showed up and then it said Verizon Wireless. After I get through the lock screen, I would go through the same whole routine - e.g. try and get into settings, freeze, hold power, have it come back up, etc. So I battery pulled again.
Finally, I got it to boot OK, by just letting it be for 10 minutes and completely ignoring it.
However, today my battery drain was pretty fast, it was on for 12 hours and was down to 40% after only 30 minutes of screen time. The culprit was "Android System" at 61%, i've never seen this that high before. Because of the high "Android System" power usage, I thought it might be good to power it down. Upon boot up, I assumed I'd be able to use it immediately, so I started going into Settings, and yet again it went unresponsive.
Are the two issues unrelated? What should I do?
As a warning, I'm extremely new to anything smarter than a Nokia brick, so be patient - Thanks!
As inconvenient as it is, I would recommend a full system wipe and go back to out of the box. That seems to fix everything and unfortunately it is rather difficult to diagnose issues on phones, especially unrooted.
In order to do a wipe you can do one of two things, goto settings then backup and reset, then hit factory data reset.
-OR-
Turn off the phone. When you start it again hold volume-up, power, and home to get into recovery. Then do the factory reset.
Ok, I thought that's what my option was. Thanks dwibbles.
Related
I hope someone can help me, I have a Sprint Touch Pro2. Last night it randomly started rebooting itsself, i was not loading a new rom, i was not installed any software, i wasn't doing anything other that texting and IMing people. After i removed the SD Card, there were a few times i got it to load to the unlock screen, but once i got passed that it would say "starting device activation..." or something like that. Then i got it loaded but Touch Flo 3D would not automatically start. So i removed the battery and restarted it again and i went to bed and left it charging, and it kept restart itself again, when i woke up it the phone was dead, and will not turn on. The charging light is on but it will not turn on.
This happenned to me, i ended up having to exchange the phone.
have u tried a hard reset. U can do this by holding power button and call and end keys.
Phone must be off and it will completely erase your data
this sounds like what my phone is doing. is there a fix? i think im sol because i didnt buy it though sprint.
Not Hopeless
This happened to my Sprint TP2 I soft and hard-reset it but it still went back to the reboot loop.
I put it in the tri-boot screen and re-reflashed the stock ROM and all was well.
Same here
The same thing is happening for me right now. Soft-resets aren't helping. It's sporadic, however, sometimes saying it successfully activated and needs to reboot (then going into activation right away), sometimes saying it failed, and sometimes not coming up at all (but I'm pretty sure it's running in the background, even if I hit cancel, because the phone is very warm and the battery drains very quickly).
I took it to Sprint and they confirmed it was already activated. They tried manually activating it, succeeded, and it still kept doing it. However, both them and I were able to place a phone call, text, and visit a website... so basically it was working. But, like I said, this constant nagging of activation was running in the background sucking juice and killing performance. Their diagnosis was "it's acting weird". The main home screen clock has also been stuck at 0:00 ever since this started (though the lock screen clock and clocks in the World Clock screen are correct).
They said I could go to their service shop and do a diagnostic and backup/wipe/restore or they'd replace it under warranty if it still didn't work.
I figured I'd just try the hard reset myself tonight. Will post how that goes. I'm not sure what this "tri-boot" screen is, but I'll do some searching and check that out too.
Samsung Galaxy Tab 2 10.1 Hacked, Touchscreen unresponsive
Hi! I need help with my tablet.
Device: Samsung Galaxy Tab 2 10.1 Tablet, model GT-P5113 TS. This model doesn't have a way to yank out the battery.
What's wrong: Touchscreen is not responding.
Current state: Attempting to drain the battery. Doesn't appear to be turned on. Factory reset apparently performed.
What happened: Sorry, this is long. It is as best as I can remember it. It may be somewhat inaccurate.
Yesterday evening, I was on my Windows laptop and logged into my Google account. I *thought* I used the Google Play Store to install Chrome to the tablet. (I had looked at the html5test website and it said Chrome had a higher HTML5 rating than the Dolphin/Jetpack browser I've been using on my tablet.)
But something went terribly wrong.
After sending Chrome to it, I unlocked the tablet and used both Chrome and Dolphin to go to html5test website. They both scored the same or nearly the same. I don't know if any of that is relevant, but I'm including it just in case.
At some point after that, I woke the tablet with the power key and used my unlock pattern on the dots lock screen.
That's when I saw what I believe was mal-ware in action. The settings menus were scrolling and sub-menus being selected, all by themselves. I couldn't say exactly what was changed because whatever program or script that was running the process was going extremely fast.
When I realized it might be trying to send out data over my Wifi network, I turned off the Wifi router in my home.
I repeatedly held down the power key to turn the system off, but doing so only rebooted back to the useless lock screen which was not responding to anything. The normal method of holding the power button for a few seconds to bring up the menu and then tapping the "Power Off" option on that menu refused to power off the system. Nothing on that menu responded to touch.
Entering my pattern on the lock screen did absolutely nothing. I didn't even see any lines traced when I ran my finger over the screen.
At some point, I pulled out the external SD card. I have no idea if whatever hacked the tablet also put a copy of itself on the SD card.
I called a friend who looked up how to restore the tablet to factory settings. I didn't understand the directions exactly, so I ended up on a screen with a Warning!! about installing a Custom OS. (Holding down the Power + Volume Up seems to get me there)
I left it on this screen, and I turned my router back on and using my laptop, contacted Live Chat at Samsung but they didn't understand my problem. They told me to reboot the device and swipe my pattern several times and then after several failed attempts I would have the chance to use my Google credentials to get into it. But the device apparently never registered that my swipe attempts were failing.
So my device was booted up with me locked out, with the WiFi router on for a little while again. I turned off the router as soon as I realized that. That disconnected the chat session, but since Samsung chat wasn't helping me anyway, I didn't bother trying to go back.
I got the device back to the "Warning!!" screen. Then turned the router back on and searched for how to do a factory reset of the device. I found a video on YouTube and followed it.
I pressed the Volume Down and Power buttons simultaneously, followed by letting go of the power button. That brought up a menu which contained several options, including an option to do a factory reset. I used the volume buttons to highlight that and pressed Power key. A second screen came up and I used the volume buttons and power button to select "Yes" to confirm the reset.
It appeared to have done a factory reset, rebooting eventually.
However, after that, when I tried to tap on the touch screen to move forward through the selections, the touch screen was still unresponsive!
So I brought back the "Warning!!" screen and ran the battery down until the screen was blank and it wouldn't start when I held the power key.
Then I charged it for about 20 minutes and rebooted it. I think when it came back it was on the Recovery menu. I think I did a second factory reset, but not 100% sure. It eventually rebooted after a lot longer than usual.
When it came up, it was saying battery was low. I tried to tap the OK button, but nothing happened. Behind the battery window was the first setting screen to set up the device for the first time after a factory reset. (I think selecting USA?)
I brought back the "Warning!!" screen and left it on overnight so that the battery would run down.
That was about 8 hours ago. When I woke up, I used clear tape to keep the power button pressed down, to ensure that the battery will continue to run down.
____________________________________________
What do I do next? How do I get the touch screen to start working again? It is not a hardware problem, unless mal-ware can break the hardware. The touchscreen had been working fine until this happened.
Should I take the tablet back to Best Buy where I bought it at least a year (maybe 2 years) ago? I don't know if it's still under warranty.
I have over 20 year of experience as a software developer, but not for Android. I am not very experienced with doing anything to hardware.
Should I try to fix it myself?
I have never rooted any Android device and I'm not sure what that means, either.
I've never re-installed the ______ ? (rom? image? Odin?)
I read on this and/or other forums that there's a way to replace something, but the instructions were beyond my level of understanding. I would need the procedures to be broken down into steps which don't assume too much about what I know.
I understand how to download a file to Windows, given a URL for it. I understand what a zip file is and how to extract it. I understand how to press hardware buttons and plug in cables, and do these steps in the order I'm told.
I don't understand what I'd use to get the downloaded whatever-they-are onto the tablet to replace whatever-the-other-thing-is so that the touchscreen works again.
As far as I know, Odin is a Norse god.
The only firmware updates I've ever done are the ones that the device does on it's own through Samsung's updates.
I'd deeply appreciate getting this device back since I have extremely limited funds and probably won't be able to buy a replacement.
Thank you,
Linda
LMurphy said:
Samsung Galaxy Tab 2 10.1 Hacked, Touchscreen unresponsive
Hi! I need help with my tablet.
Device: Samsung Galaxy Tab 2 10.1 Tablet, model GT-P5113 TS. This model doesn't have a way to yank out the battery.
What's wrong: Touchscreen is not responding.
Current state: Attempting to drain the battery. Doesn't appear to be turned on. Factory reset apparently performed.
What happened: Sorry, this is long. It is as best as I can remember it. It may be somewhat inaccurate.
Yesterday evening, I was on my Windows laptop and logged into my Google account. I *thought* I used the Google Play Store to install Chrome to the tablet. (I had looked at the html5test website and it said Chrome had a higher HTML5 rating than the Dolphin/Jetpack browser I've been using on my tablet.)
But something went terribly wrong.
After sending Chrome to it, I unlocked the tablet and used both Chrome and Dolphin to go to html5test website. They both scored the same or nearly the same. I don't know if any of that is relevant, but I'm including it just in case.
At some point after that, I woke the tablet with the power key and used my unlock pattern on the dots lock screen.
That's when I saw what I believe was mal-ware in action. The settings menus were scrolling and sub-menus being selected, all by themselves. I couldn't say exactly what was changed because whatever program or script that was running the process was going extremely fast.
When I realized it might be trying to send out data over my Wifi network, I turned off the Wifi router in my home.
I repeatedly held down the power key to turn the system off, but doing so only rebooted back to the useless lock screen which was not responding to anything. The normal method of holding the power button for a few seconds to bring up the menu and then tapping the "Power Off" option on that menu refused to power off the system. Nothing on that menu responded to touch.
Entering my pattern on the lock screen did absolutely nothing. I didn't even see any lines traced when I ran my finger over the screen.
At some point, I pulled out the external SD card. I have no idea if whatever hacked the tablet also put a copy of itself on the SD card.
I called a friend who looked up how to restore the tablet to factory settings. I didn't understand the directions exactly, so I ended up on a screen with a Warning!! about installing a Custom OS. (Holding down the Power + Volume Up seems to get me there)
I left it on this screen, and I turned my router back on and using my laptop, contacted Live Chat at Samsung but they didn't understand my problem. They told me to reboot the device and swipe my pattern several times and then after several failed attempts I would have the chance to use my Google credentials to get into it. But the device apparently never registered that my swipe attempts were failing.
So my device was booted up with me locked out, with the WiFi router on for a little while again. I turned off the router as soon as I realized that. That disconnected the chat session, but since Samsung chat wasn't helping me anyway, I didn't bother trying to go back.
I got the device back to the "Warning!!" screen. Then turned the router back on and searched for how to do a factory reset of the device. I found a video on YouTube and followed it.
I pressed the Volume Down and Power buttons simultaneously, followed by letting go of the power button. That brought up a menu which contained several options, including an option to do a factory reset. I used the volume buttons to highlight that and pressed Power key. A second screen came up and I used the volume buttons and power button to select "Yes" to confirm the reset.
It appeared to have done a factory reset, rebooting eventually.
However, after that, when I tried to tap on the touch screen to move forward through the selections, the touch screen was still unresponsive!
So I brought back the "Warning!!" screen and ran the battery down until the screen was blank and it wouldn't start when I held the power key.
Then I charged it for about 20 minutes and rebooted it. I think when it came back it was on the Recovery menu. I think I did a second factory reset, but not 100% sure. It eventually rebooted after a lot longer than usual.
When it came up, it was saying battery was low. I tried to tap the OK button, but nothing happened. Behind the battery window was the first setting screen to set up the device for the first time after a factory reset. (I think selecting USA?)
I brought back the "Warning!!" screen and left it on overnight so that the battery would run down.
That was about 8 hours ago. When I woke up, I used clear tape to keep the power button pressed down, to ensure that the battery will continue to run down.
____________________________________________
What do I do next? How do I get the touch screen to start working again? It is not a hardware problem, unless mal-ware can break the hardware. The touchscreen had been working fine until this happened.
Should I take the tablet back to Best Buy where I bought it at least a year (maybe 2 years) ago? I don't know if it's still under warranty.
I have over 20 year of experience as a software developer, but not for Android. I am not very experienced with doing anything to hardware.
Should I try to fix it myself?
I have never rooted any Android device and I'm not sure what that means, either.
I've never re-installed the ______ ? (rom? image? Odin?)
I read on this and/or other forums that there's a way to replace something, but the instructions were beyond my level of understanding. I would need the procedures to be broken down into steps which don't assume too much about what I know.
I understand how to download a file to Windows, given a URL for it. I understand what a zip file is and how to extract it. I understand how to press hardware buttons and plug in cables, and do these steps in the order I'm told.
I don't understand what I'd use to get the downloaded whatever-they-are onto the tablet to replace whatever-the-other-thing-is so that the touchscreen works again.
As far as I know, Odin is a Norse god.
The only firmware updates I've ever done are the ones that the device does on it's own through Samsung's updates.
I'd deeply appreciate getting this device back since I have extremely limited funds and probably won't be able to buy a replacement.
Thank you,
Linda
Click to expand...
Click to collapse
Definitely sounds like malware. You have two choices that I see, either root and custom rom or flash back to stock. Since you are stock you'd just be overwriting your existing install. Read this thread and decide your course of action http://forum.xda-developers.com/showthread.php?t=2203309
Bought a Nexus 5 about 6 months ago USED. It has been amazing. I got the latest OTA a week ago or so, not sure if that has anything to do with current issues.
About 2 days ago started randomly restarting. Today, it shut down and has been in continuous loop restarting. I see "Google" and maybe even the boot dots loading, then it is off. Three seconds later, starts again and repeats. Never makes it all the way into Android system. I let it sit for a while and when I pick it up, without touching any buttons, it repeats all of this. I suppose it is probably dead in general, but I don't know. Do you guys have any ideas? Again, I bought it used and from a ma/pap store who said they buy 100 in bulk, which made me skeptical, but they also had a 60 day guarantee and it was amazing the first 60 days and even after. It has been error free for 6 months, so I don't know if this is just a random issue or if the previous owner dropped it in a lake and I got lucky, or what. FWIW the damn thing has been in a case and never dropped, so it isn't anything that I have done I don't think. Thanks for any help.
edit: never rooted, never messed with, always been stock
Another user reported some instability since the last OTA update.
Flashing the full factory images did the trick.
a friend of mine gave me his nexus 5 to repair and its doing something similar. He had ir rooted and on latest 5.1.1 (i think). Either way, he said it was randomly locking up and rebooting. When i got it it had the red blinking light when plugged so i got a new battery. That got fixed but then the constant bootloop showed itself. I flashed TWRP (many versions, 2.6.3.1; 2.7.1.1; 2.8.7.1; the one that worked best was 2.7.1.1). So, once in twrp wiped, pushed cm 12 snapshot, flashed it, pushed gapps, falshed, pushe supersu flashed. Started the system. That precise order of things (ie: pushing flashing, then pushing something new and flashing it) was what gave me best results to actually boot up at least once. Once booted up and logging in and everything to cm i had some sort of stability (even rebooting and powering off) but i think that everything went wrong when i plugged the phone to the computer and it was back to bootloops and not even getting to the recovery. Flashed everything again. Didnt work. Had to leave the phone sit for a while (without the back casing) before trying again, in order, before getting any success. Im starting to think of ovrheating but it doesnt even get that hot...
Dunno if you guys have any ideas on this. Or if i can give you mor details to help us out.
Regards!
Looks like I'm having a similar problem to what is described here, as well as http://forum.xda-developers.com/google-nexus-5/help/bootlooped-dont-how-to-enable-debugging-t3215951
I've had one of my Nexus 5 phones running OmniROM 5.1.1 for some time now, very stably. After trying out the Marshmallow preview and going back to that ROM, I started having spontaneous hard reboots and hard crashes. The phone would often boot loop before even getting to the OmniROM boot animation. It was also very recalcitrant about entering and staying in the boot loader, rebooting spontaneously shortly after rendering the boot loader screen. I was occasionally able to "grab" control long enough to get it to boot into TWRP, from which a boot to Android seemed to usually get it out of the loop and into running Android.
I've flashed back the boot loader and baseband from factory-stock 5.1.1 LMY48M (HHZ12h and 2.0.50.2.26) using the flash-base.sh script from a freshly downloaded and extracted hammerhead-lmy48m. Things appeared to be OK last evening and this morning, but things got worse today.
Now the phone is in a state where it is not responsive to the power button when unplugged. I can hold it down for 30 seconds with no response.
If I plug in USB, it spontaneously starts rebooting, not showing more than about two seconds of the Google boot loader screen. If I hold the down-volume button, I can get the boot-loader screen, but no matter how fast I try to be, I can't select anything more than "Restart bootloader" (or "Power off") option before it spontaneously reboots (to boot loader).
As far as I know, the battery had a significant charge before this started happening.
I see the same behavior if the phone is connected to a USB charging source, rather than a USB port.
I've tried pulling the SIM, but that doesn't change the behavior.
adb wait-for-device never returns, so poking it over adb doesn't seem to be an option.
fastboot devices also doesn't see the phone, for the brief time the boot loader is running.
Any suggestions on how to get this into the boot loader so I can at least re-flash it?
Nexus 5 D820(E) 32 GB
Edit:
WaxLarry said:
In my opinion your problems seems power button's related.
Click to expand...
Click to collapse
Trying to see how I can "clean" or "clear" the power button now.
Edit:
Paul22000 said:
This morning my Nexus 5 was turned off all of a sudden after not having used it for 20-30 minutes. I held the power button and nothing. I plugged it into power and the "Google" screen appeared. It then went into a reboot loop on and off, on and off, on and off. I held the Volume Buttons and it went into fastboot, but then boot looped out again and again. Searching on Google yielded that this was indeed a common problem. [...]
Click to expand...
Click to collapse
Edit: Repeatedly pressing the power button seems to have temporarily allowed a boot to Android.
In retrospect, I had noticed over the last few days that the phone didn't seem to respond properly to the power button, either "ignoring" it, or when a second press got things started, it would unexpectedly come up with the long-press-volume menu.
One link on how to replace the power switch yourself is http://protyposis.net/blog/replacing-the-nexus-5-power-button/
Ok @jeffsf keep going on this thread. I had the same damn experience, that ended with RMA. LG said that the problem is related to some tension change in the power button. After the RMA I used the phone totally stock and never had a problem. Two months ago I switched to blu_spark kernel and some weeks after i noticed some problem. When I pressed the button to lock the screen, phone locked itself and then screen turned on, sometimes showing the shutdown option. So i understood that something was happening to the power button. I tried to overvolt with a +5mV on general offset and since then i never had problem. If you can enter recovery or bootloader i suggest you to flash some kernel with volt change support and then overvolt the general offset... and keep finger crossed
jeffsf said:
Looks like I'm having a similar problem to what is described here, as well as http://forum.xda-developers.com/google-nexus-5/help/bootlooped-dont-how-to-enable-debugging-t3215951
I've had one of my Nexus 5 phones running OmniROM 5.1.1 for some time now, very stably. After trying out the Marshmallow preview and going back to that ROM, I started having spontaneous hard reboots and hard crashes. The phone would often boot loop before even getting to the OmniROM boot animation. It was also very recalcitrant about entering and staying in the boot loader, rebooting spontaneously shortly after rendering the boot loader screen. I was occasionally able to "grab" control long enough to get it to boot into TWRP, from which a boot to Android seemed to usually get it out of the loop and into running Android.
I've flashed back the boot loader and baseband from factory-stock 5.1.1 LMY48M (HHZ12h and 2.0.50.2.26) using the flash-base.sh script from a freshly downloaded and extracted hammerhead-lmy48m. Things appeared to be OK last evening and this morning, but things got worse today.
Now the phone is in a state where it is not responsive to the power button when unplugged. I can hold it down for 30 seconds with no response.
If I plug in USB, it spontaneously starts rebooting, not showing more than about two seconds of the Google boot loader screen. If I hold the down-volume button, I can get the boot-loader screen, but no matter how fast I try to be, I can't select anything more than "Restart bootloader" (or "Power off") option before it spontaneously reboots (to boot loader).
As far as I know, the battery had a significant charge before this started happening.
I see the same behavior if the phone is connected to a USB charging source, rather than a USB port.
I've tried pulling the SIM, but that doesn't change the behavior.
adb wait-for-device never returns, so poking it over adb doesn't seem to be an option.
fastboot devices also doesn't see the phone, for the brief time the boot loader is running.
Any suggestions on how to get this into the boot loader so I can at least re-flash it?
Nexus 5 D820(E) 32 GB
Edit:
Trying to see how I can "clean" or "clear" the power button now.
Edit:
Edit: Repeatedly pressing the power button seems to have temporarily allowed a boot to Android.
In retrospect, I had noticed over the last few days that the phone didn't seem to respond properly to the power button, either "ignoring" it, or when a second press got things started, it would unexpectedly come up with the long-press-volume menu.
One link on how to replace the power switch yourself is http://protyposis.net/blog/replacing-the-nexus-5-power-button/
Click to expand...
Click to collapse
I got a notification for this post since you quoted me. I'm not sure if you're having the same problem but I'll tell you what happened to me, just in case. I called T-Mobile and they referred me to the nearest 3rd party phone repair shop. I went there and after an evaluation, the repairman told me the power button on my phone was indeed broken. They replaced it for $55.
The story doesn't end there though. I took my phone home and a few hours later I tried to use bluetooth and it didn't work. I took it back and found out that unfortunately, when the guy replaced the power button, he inadvertently broke the bluetooth. There's no way to fix bluetooth without replacing the motherboard entirely, which would cost $200. I'd rather buy a new phone at that point since my Nexus 5 was getting old. He refunded me, which was nice. At least the power button worked so I could use my phone. Bluetooth isn't as valuable as being able to you know, turn on the phone, so at least it was a net gain.
After that, I purchased a Nexus 6 and rooted it so I could use double-tap-to-wake (along with the automatic screen on when you pick up the Nexus 6). I also use the following app in order to turn off the screen by swiping up from the home button (I don't care about losing the shortcut to Google Now): Screen Off and Lock
I can now literally go weeks without using the power button on my Nexus 6. (I literally only use it when tap to wake sometimes becomes unresponsive which is rare.)
Bottom line: I will never buy another phone without tap to wake functionality! :good:
A local repair shop here indicated that one sometimes does changing the power switch resolve the issue. They have seen situations where the issue appears to be one of the power-management ICs. Just something to be aware of when examining the potential cost of a repair and who you would have do the work.
Hey everyone who reads this.
I'd like to start my topic with apologising if I post this in the wrong section.
So, I have a LG Spirit H440N LTE for about 3 years now, maybe a little less. I've always taken good care of it, both physically and in updates / security wise aswell.
My phone has been working flawlessly until the last 2 days. 2 days ago i was charging my phone, and when it vibrated (meaning its 100%) I pulled the cable off, and pressed the power button (power button locks - unlocks the screen) the screen didn't turn on. I was like "wow that's strange" but didn't care much, i just kept pressing the button every 5-6 seconds, nothing.
At that point I pulled the battery out, let it sit for a short time and then put it back, start the phone, I felt the vibration (meaning it's starting up) but no screen, so my first idea was that I need to get a new firmware and completely reinstall my phone, as it seems like it got bricked.. for no reason, by itself ? Strange thing but I accepted it and literally been googling for 9 hours now and I find more and more issues.
After I got LG FlashTool, drivers, and even 3 different firmwares, I wanted to start the phone in download mode to start upgrading, but even though I held down "volume up for 5 seconds and then put the usb cable in" nothing happened, no screen, my PC didn't recognise the phone either.
So I got a little bit mad and pulled the cable out from the phone, I wanted to remove the battery, but out of nowhere the phone suddenly started loading in, screen working completely fine, i could do whatever i want, so my first thing was to do a hard reset. After the hard reset I set up my usual stuff (important apps etc) and I locked the screen so my battery won't go down. Little did I know, I ****ed up again, because ever since that happened, I can't get my screen to work again. I tried everything I could but my PC still doesn't recognise the phone (even after a LOT of drivers being installed), charging the phone doesn't do anything. Regardless if I remove - put back the battery no screen, no screen in download - hard reset mode either, it's just completely black.
I'd like to have some sort of help, because I am just completely out of ideas, I really feel like a firmware change could fix the phone, but if the computer doesn't recognise it, I have no idea what to do.
rawon3 said:
Hey everyone who reads this.
I'd like to start my topic with apologising if I post this in the wrong section.
So, I have a LG Spirit H440N LTE for about 3 years now, maybe a little less. I've always taken good care of it, both physically and in updates / security wise aswell.
My phone has been working flawlessly until the last 2 days. 2 days ago i was charging my phone, and when it vibrated (meaning its 100%) I pulled the cable off, and pressed the power button (power button locks - unlocks the screen) the screen didn't turn on. I was like "wow that's strange" but didn't care much, i just kept pressing the button every 5-6 seconds, nothing.
At that point I pulled the battery out, let it sit for a short time and then put it back, start the phone, I felt the vibration (meaning it's starting up) but no screen, so my first idea was that I need to get a new firmware and completely reinstall my phone, as it seems like it got bricked.. for no reason, by itself ? Strange thing but I accepted it and literally been googling for 9 hours now and I find more and more issues.
After I got LG FlashTool, drivers, and even 3 different firmwares, I wanted to start the phone in download mode to start upgrading, but even though I held down "volume up for 5 seconds and then put the usb cable in" nothing happened, no screen, my PC didn't recognise the phone either.
So I got a little bit mad and pulled the cable out from the phone, I wanted to remove the battery, but out of nowhere the phone suddenly started loading in, screen working completely fine, i could do whatever i want, so my first thing was to do a hard reset. After the hard reset I set up my usual stuff (important apps etc) and I locked the screen so my battery won't go down. Little did I know, I ****ed up again, because ever since that happened, I can't get my screen to work again. I tried everything I could but my PC still doesn't recognise the phone (even after a LOT of drivers being installed), charging the phone doesn't do anything. Regardless if I remove - put back the battery no screen, no screen in download - hard reset mode either, it's just completely black.
I'd like to have some sort of help, because I am just completely out of ideas, I really feel like a firmware change could fix the phone, but if the computer doesn't recognise it, I have no idea what to do.
Click to expand...
Click to collapse
You might be having hardware issues, such as a faulty power button. If you are the type of user that frequently presses the power button to lock/unlock the screen, this leads to excessive wear on the button components, this is why some users prefer to use the "tap to sleep" and "tap to wake" feature, to avoid wearing the power button out. On my LG, this feature is called "KnockOn", it's located in Accessibility settings.
Sent from my LGL84VL using Tapatalk
Hi everyone, I'm throwing this out there because I've run out of ideas about what has just happened to my U12+ (64gb) today.
I woke up and used my phone as normal, caught up on Twitter and the news, the usual apps etc. nothing untoward. The same routine I've had with my phone for the past 18 months of owning it with zero issues. My handset is stock OS (Android 9) and so not rooted or anything like that. Virtually all the apps I use are standard issue from the Play Store, nothing really "out there" and I have BitDefender installed to look after security. Same setup I've had for over a year. The battery was around 35% so I plugged it into my wall charger while I went off to grab some breakfast. When I returned a couple of hours later the light on the handset was green, I unplugged the charger and attempted to unlock it with my fingerprint.
The phone asked for my PIN, no big deal so I entered it. Black screen. Tapped the power button again, it requested my PIN again, I entered and... black screen. Okay, I was a little bit concerned now. I held down the power button so the haptic buzz occurred, held for 10/20/30 seconds, a minute... nothing, no restart. Tap the power button and it asks me for my PIN again and shows yet another black screen. I held down Power + Volume Down but again, nothing and no restart.
I asked someone to call me, the screen came to life and I could take the call but each time I tried to pull down the system tray in order to try and reach Settings to restart it asked me for my PIN, I entered it = black screen. The call was unaffected.
I removed my SIM + microSD card tray = same deal as above.
The phone is clearly responsive in some way and the screen does display to ask for my PIN but I can't get into it in order to reboot it. Extremely worrying.
Does anyone have any advice? At the moment I am faced with the prospect of simply allowing the battery to run out so the phone shuts down naturally but that is going to take the best part of 2 days.
I'm really disappointed because I was planning another 1-2 years use for this handset as I just bought a 1TB microSD card which has been fine in the phone for weeks so I don't think that's the cause. It is also genuine SanDisk.
Any suggestions or advice? Thanks in advance.
Hello, I hope you have made a backup with google backup recently... This does not happen often on android, but sometimes the system could have a problem. You can try this go the bootloader with the power and volume buttons , after recovery.. after apply a wipe data/ factory reset.. is will make a factory reset of your phone except the sd card. You should by fine after that and profit again.
Thanks, I appreciate your reply.
At the moment I am running the battery down until the handset switches off naturally. When it comes back on I will try to launch the phone normally, if that doesn't work I'll run the battery down again and attempt to reach the bootloader.
My photos are backed up to the cloud, I may lose some text messages but I managed to transfer the majority of my 2FA over to another Android device bar one.
At the end of the day if it's a choice between wiping it or a bricked/unusable handset then I don't really have one. What a pain.
Magimix^ said:
Thanks, I appreciate your reply.
At the moment I am running the battery down until the handset switches off naturally. When it comes back on I will try to launch the phone normally, if that doesn't work I'll run the battery down again and attempt to reach the bootloader.
My photos are backed up to the cloud, I may lose some text messages but I managed to transfer the majority of my 2FA over to another Android device bar one.
At the end of the day if it's a choice between wiping it or a bricked/unusable handset then I don't really have one. What a pain.
Click to expand...
Click to collapse
At the moment I am running the battery down until the handset switches off naturally <----- why that??? Even on a bootloop or a black screen you can reset it hold the buttons power and the volume, you can go on the bootloader.
Max128 said:
At the moment I am running the battery down until the handset switches off naturally <----- why that??? Even on a bootloop or a black screen you can reset it hold the buttons power and the volume, you can go on the bootloader.
Click to expand...
Click to collapse
The first thing I tried to do was hold down the power button or the power button in tandem with the volume buttons but the handset won't restart. I tried loads of times holding it for different amounts of time and... nothing.
Trust me, I tried.
The only way I can get the device to switch off is by draining the battery. I'm almost at 20% so it shouldn't be too much longer.
Well I already got a black screen after flashing a module magisk.. I have holding the power button and the phone have restart no problem, same thing on bootloop. You need to be sure to hold the button correctly.
Max128 said:
You need to be sure to hold the button correctly.
Click to expand...
Click to collapse
Yeah, I'm certain I was holding the buttons correctly. I tried about 20 times using different combinations just to be sure but the device would not restart. The haptic shock buttons are one of my least favourite features of the u12+, it's got to be said.
Anyway, the phone ran out of battery about 15 minutes ago. I left it alone for few minutes and switched it back on. It allowed me back in and the device appears to be fully functional again. I can unlock by thumb print, face or PIN without issue.
Basically, it's fixed. My only concern is I have no idea what caused it or if it will happen again.
Thanks for offering help though, I appreciate it. I'm not sure if this thread can be closed/locked now? I'll look into that.
Cheers.
Yes.. i love the buttons too i never got a problem with this. Great if is fixed! Maybe make a factory reset the next time.
I am wondering if the new flagship have haptic buttons too.. htc will announce it Tuesday.