Related
Ok I was flashing back to stock 2.1 useind odin when mid process my phone fell battery out usb disconnected and bam thats it. Now my phone is locked on a screen that shows a picture of a phone ! and a computer. I can get it back to download mode and odin will se the phone but gets no further then do not unplug device, my computer beeps when its plugged in but it dose not show the phone in my computer section. Any fixes or am i screwed?
PS phone is only two weeks old if need be could I take it back like this????
Hmm I think I may hove gotten past this problem. Uninstalled odin reinstalled and now it seems to be hopefully working
Here is the fix
I was in this same situation yesterday. Here is how to get it back into download mode.
•Be sure the Samsung USB drivers for the phone are installed on your computer.
•Remove and replace the battery.
•Connect the phone to the computer with the USB cable. The "phone-exclamation mark-computer" picture should display on the phone's screen.
•Hold the Volume Up+Volume Down+Power buttons down simultaneously.The screen should go blank, then the picture should appear again. When the screen goes blank a second time, release the Power button while continuing to hold the Volume Up+Volume Down buttons down
If that doesn't work,i had a similar problem where I could get into odin, but it would progress beyond the pit file. Take the battery, sim and memory card out of your phone. Start odin. Put the battery only back in. hold volume up and down. Plug the phone in while holding these buttons. Don't let go until you are in download mode. Now try restoring. It should work.
Thanks for the input i am back up and running!!
Sent from my SAMSUNG-SGH-I897 using XDA App
Bricked replacement Captivate - Orange Screen
Just to let you know. I recently received a replacement captivate thru warranty exchange. The phone was apparently a new one with JF6. So I decided to do an update to JH7 using Kies mini. A little over half way to the update procedure, the phone screen turned orange and stayed there for a long time, eventually I had to pull the plug. Of course I had to manually go to download mode and launch Kies mini emergency recovery, the damn thing again got stuck at the orange screen.
If anybody has this experience do no proceed further and throw that damn thing back at At&T's face. Do not attempt to do anything. I made a mistake of then doing an ODIN one-click back to stop and the phone got stuck half way, went to the orange screen.. and then it was over.. The phone was dead, wouldn't turn on, no recovery or download mode with any button combo. When I plugged in to the wall, no battery indicator.
save yourself the trouble and return the damn thing
still there
I am a "noob" to posting here, and a noob to the android due to being an avid iPhone user. I am having the same problem, phone -!- computer and have tried every method i can find in this forum to get passed it. Are there any other thoughts or suggestions? (got hung at do not turn off target in odin) Thanks in advance to any help.
I would look at this thread http://forum.xda-developers.com/showthread.php?t=1153310
Stephenv1971 said:
I would look at this thread http://forum.xda-developers.com/showthread.php?t=1153310
Click to expand...
Click to collapse
went that route, still cant find dl mode. have resistors built and all. any way i try to boot shows me the phone -!- computer, and the computer doesnt attempt to recognise it so there is no communication between the computer and phone. unfortunately, i dont have a v/ohm meter, so i am not sure of the accuracy of the resistors i used to make my jig.
I fixed this many times with phone that had the button download mode and didn't.
Getting into download mode while softbricked like this wont show the normal download screen. IT will still show the error screen....
With download mode working still:
Simply remove the battery and replace,
Open odin
Hold down volume keys and plug it in till you see odin recognize ur phone.
Then continue to use odin.
Dosent work, repeat.
If you know ur button combo dosent work:
Just open odin.
Remove battery & replace.
Use jig (3k 100k ohms twisted)
Then when the phone turns on and your see the pc! screen plug in usb.
See if odin sees it.
Assuming your flash didn't fail on the PBL.bin or SBL.bin you should be fine.
Follow the methods suggested by other users here and you will get back up and running in no time at all.
Don't sweat the 'phone-!-pc' screen. I'm a little surprised that no one has given you the good news....that is just a version of the download screen for later hardware revisions. It looks bad, but if Odin recognizes your phone (if one of the COM fields goes active), just start your flash again.
Now if Odin does not recognize the phone when plugged in via USB, then you have some more work to do.
I had forgotten about posting here, and my problem has been resolved. So here it is... I tried everything that I could find within this forum, almost. I built my own jig with inferior radio shack components that would not activate download mode, though it would turn the phone on. I got wise, spent 8 dollars at ebay and purchased a JIG there. Instant download mode after 3 days (shipping). Reflashed with one click, updated w/ kies, made kernal changes and am now rockin my captivate. Thanks to those who assisted.
Steve_O_1971 said:
I had forgotten about posting here, and my problem has been resolved. So here it is... I tried everything that I could find within this forum, almost. I built my own jig with inferior radio shack components that would not activate download mode, though it would turn the phone on. I got wise, spent 8 dollars at ebay and purchased a JIG there. Instant download mode after 3 days (shipping). Reflashed with one click, updated w/ kies, made kernal changes and am now rockin my captivate. Thanks to those who assisted.
Click to expand...
Click to collapse
Using the 3-resistor method takes A LOT of patience, at least in my experience. Glad everything worked out.
beast534 said:
Using the 3-resistor method takes A LOT of patience, at least in my experience. Glad everything worked out.
Click to expand...
Click to collapse
Patience is a virtue, and my Ex's name. LOL! I can do without patience.
Jokes aside, i actually soldered the resistors to a plug that i had cut up, and made sure it was covered so my skin wouldnt come in contact. The Radio Shack here buys inferior products and sells them at reggular retail. Unfortunately my $300.00 V-Ohm meter is on the fritz, and i have not had the time or money to replace it yet, but I have intentions to check the actual resistance of the jig I made. ^^
I have been having trouble with my Bell Vibrant for the past few days, with a black screen after the 'S' Tried several things out there to resolve this issue, nothing seemed to work.
In desperation I tried the Odin3 one-click, not noticing its for the captivate. I successfully flashed and am now in a reboot loop with the AT&T logo screen. I can't get into recovery mode. or download mode to re flash with different ROM.
Any ideas????
Yes this is a vibrant device running a captivate rom and I have also posted this question in Vibrant general.
[email protected] said:
I have been having trouble with my Bell Vibrant for the past few days, with a black screen after the 'S' Tried several things out there to resolve this issue, nothing seemed to work.
In desperation I tried the Odin3 one-click, not noticing its for the captivate. I successfully flashed and am now in a reboot loop with the AT&T logo screen. I can't get into recovery mode. or download mode to re flash with different ROM.
Any ideas????
Yes this is a vibrant device running a captivate rom and I have also posted this question in Vibrant general.
Click to expand...
Click to collapse
Use odin for the vibrant, not familiar with that SGS phone so I don't know if they have a one click odin . If not, you will need the stock .tar or kernel, modem and zimage files.
Open Odin in windows.
Take out your extSD, Sim and battery, wait 10+ secs.
Now plug the usb in.
While holding the vol +- insert the battery and it should go into download mode.
Now you can click start in odin.
I do know that the vibrant is a pain in the ass to get into download mode and that the above is the most consistent way to get there.
This is what I know of the vibrant, correct me if I'm wrong anyone.
For what it's worth, I had a hard time getting my captivate into download mode. This is what I had to do...when you do this, have the ODIN for your phone ready because if you back out from download mode, you'll get the blessed 'phone to computer' screen...which I was still able to get into download mode from...but some people haven't had such luck.
1) Turn off phone...(take battery out or whatever)
2) Holding the two volume buttons down, SLOWLY plug in USB cord HALF-WAY. Push it in just a tad...if the screen doesn't come up with the shoveling android...push in just a little bit more...keep doing this until you get the shoveling android...if the phone turns on...you missed it - start over.
3) Once in download mode, if the ODIN program doesn't see your phone on a COM port yet...push the USB cord in the rest of the way and it should see it then. I think I actually had to unplug the cord and plug it back in slowly till it saw it. Once it does see it, don't touch the cord anymore!
4) Click start on ODIN and let it do it's thing. You should see a progress bar show up on your phone's download screen within a minute or so...if not...turn off the phone and try again. you will get the 'blessed' screen but hopefully you won't have to do it.
My heart stopped for a bit when I tried the above and it didn't work the first time and I got the 'blessed' screen. But I just tried again and all was fine...so don't fret too much.
Anyways...hope this helps.
iceman198 said:
For what it's worth, I had a hard time getting my captivate into download mode. This is what I had to do...when you do this, have the ODIN for your phone ready because if you back out from download mode, you'll get the blessed 'phone to computer' screen...which I was still able to get into download mode from...but some people haven't had such luck.
1) Turn off phone...(take battery out or whatever)
2) Holding the two volume buttons down, SLOWLY plug in USB cord HALF-WAY. Push it in just a tad...if the screen doesn't come up with the shoveling android...push in just a little bit more...keep doing this until you get the shoveling android...if the phone turns on...you missed it - start over.
3) Once in download mode, if the ODIN program doesn't see your phone on a COM port yet...push the USB cord in the rest of the way and it should see it then. I think I actually had to unplug the cord and plug it back in slowly till it saw it. Once it does see it, don't touch the cord anymore!
4) Click start on ODIN and let it do it's thing. You should see a progress bar show up on your phone's download screen within a minute or so...if not...turn off the phone and try again. you will get the 'blessed' screen but hopefully you won't have to do it.
My heart stopped for a bit when I tried the above and it didn't work the first time and I got the 'blessed' screen. But I just tried again and all was fine...so don't fret too much.
Anyways...hope this helps.
Click to expand...
Click to collapse
He is on a vibrant, not a captivate although it should be close to the same procedure. I've seen the usb half plug method but it never did anything for mine.
A jig should do the trick. Get a MicroUSB-b plug breakout board from sparkfun.com and two resistors (300k+1k) in serial across pins 4 and 5. Turn your phone off and take the battery, sim, and external sd card out. Pop the jig into the usb slot and put the battery back in. The phone should go into download mode on it's own without you having to hit any buttons.
After that, just follow what everyone else said - use a one-click-stock odin for your particular model.
The jig worked. took a trip to the source and grabbed the resisters and took apart the micro USB adapter included in my BlueAnt handsfree.
followed the directions from
http://forum.xda-developers.com/showthread.php?p=9804077#post9804077
Back in business.
Thanks all.
[email protected] said:
The jig worked. took a trip to the source and grabbed the resisters and took apart the micro USB adapter included in my BlueAnt handsfree.
followed the directions from
http://forum.xda-developers.com/showthread.php?p=9804077#post9804077
Back in business.
Thanks all.
Click to expand...
Click to collapse
Glad that worked and thanks for the update info.
Ok heres the past 12 hours of my phones life. I instalaled Zeus V5 with the ICS theme, I flashed Entropy's latest daily kernel. I was setting up my phone back to what I had it at before I restored it. It was working perfect at about 3:00 AM CST. I plugged it in and went to sleep. When I woke up at about 11:00 AM CST. My phone was off. I assumed it just shut off so I tried turning it on...nothing. I tried the 3 button push and nothing. I then took my battery out and put it back and still nothing. I've tried removing the sd the sim and the battery and then plugging it in. I've tried DL mode in several different ways. I've used different computers, different cables, different wall outlets. No matter what I can't get a single thing to detect this phone and it won't respond to any amount of button pushes...So if anyone can help me fix my phone I will send you either 50 bucks through paypal or a 50 dollar giftcard. Please I'm begging you. Anyone please help.
Do you have a different battery you can use? Sounds like it might be the one you have in there.
do you get anything on your screen at all ?
$50 can be sent to [email protected] via paypal:
Here ya go buddy
http://forum.xda-developers.com/showthread.php?t=1116251&page=2
Instructions:
1) Make sure the drivers for the Infuse 4G are installed (installing Kies is the best way to accomplish this)
2) Download and unzip GTG's_Ultimate_Unbrick.zip
3) Run Odin3 v1.7.exe as administrator
4) Place your phone into download mode (pull battery, replace battery, press and hold both volume buttons while plugging in the USB cable)
5) Make sure your phone shows up in Odin as COM##
6) Click the PIT button and choose infuse.pit (and make sure Re-Partition is checked)
7) Click the PDA button and choose PDA_UCKD5.tar.md5
8) Click the PHONE button and choose PHONE_UCKD5.tar.md5
9) Press Start
Thanks to GTG!
It has to be your battery.
Sent from my SGH-I997 using xda premium
FauxAffliction said:
Ok heres the past 12 hours of my phones life. I instalaled Zeus V5 with the ICS theme, I flashed Entropy's latest daily kernel. I was setting up my phone back to what I had it at before I restored it. It was working perfect at about 3:00 AM CST. I plugged it in and went to sleep. When I woke up at about 11:00 AM CST. My phone was off. I assumed it just shut off so I tried turning it on...nothing. I tried the 3 button push and nothing. I then took my battery out and put it back and still nothing. I've tried removing the sd the sim and the battery and then plugging it in. I've tried DL mode in several different ways. I've used different computers, different cables, different wall outlets. No matter what I can't get a single thing to detect this phone and it won't respond to any amount of button pushes...So if anyone can help me fix my phone I will send you either 50 bucks through paypal or a 50 dollar giftcard. Please I'm begging you. Anyone please help.
Click to expand...
Click to collapse
Mine did this, but it was when I was messing with different ROM's and kernels, etc. It just plain shut off. Nothing would work, not the 3 button, anything. So I pulled the battery, put it back in and plugged in my jig I bought from Mobile Tech Videos, $8 at the time, and it went into download mode. From there I went to GTG's Ultimate Unbrick, and I was fine. Try it, if you have a jig. If it works, then cool, and you don't owe me a thing.
try following the GTG unbrick up above with the odin.
i recall a post a while ago from someone who had bricked their phone and it seemed to be like yours, and one of the responses was that even though the screen didn't show up as download mode, it was still connected and able to odin properly.
when you plugged it into your computer in download mode, did odin pick it up?
You guys don't pay attention to what you read. He said, Nothing comes up on the screen and he can not put it on DL mode.
I would try getting a battery or if you know someone with an infuse, barrow the battery and see if that works. If that doesn't work, try the Jig. I'm sure with the JIG you will be able to bring back your phone from SOD...
GL
Ok guys, took it to AT&T and the guy tried like 4 new batteries. It is NOT the battery. He doesn't know what's wrong with it but then again I didn't tell them about the ROMS or rooting(duh) there is not physical or water damage at all. Anyone else??
drivel2787 said:
$50 can be sent to [email protected] via paypal:
Here ya go buddy
http://forum.xda-developers.com/showthread.php?t=1116251&page=2
Instructions:
1) Make sure the drivers for the Infuse 4G are installed (installing Kies is the best way to accomplish this)
2) Download and unzip GTG's_Ultimate_Unbrick.zip
3) Run Odin3 v1.7.exe as administrator
4) Place your phone into download mode (pull battery, replace battery, press and hold both volume buttons while plugging in the USB cable)
5) Make sure your phone shows up in Odin as COM##
6) Click the PIT button and choose infuse.pit (and make sure Re-Partition is checked)
7) Click the PDA button and choose PDA_UCKD5.tar.md5
8) Click the PHONE button and choose PHONE_UCKD5.tar.md5
9) Press Start
Thanks to GTG!
Click to expand...
Click to collapse
Doesn't go in to DL mode...try again.
Based on the description, since it had a functional ROM and died later on not in the middle of a flash:
1) Battery dead as a doornail - I BELIEVE that with certain types of jigs (potentially not the standard one) the device will turn on without a battery so this could be confirmed. If so, you might be able to fix it with a new battery OR topping off the battery in an external charger.
2) Total hardware failure of some sort, highly likely going beyond a brick. (e.g. even if you JTAGed a good bootloader it would still be dead - probably because the bootloader is still good.)
Entropy512 said:
Based on the description, since it had a functional ROM and died later on not in the middle of a flash:
1) Battery dead as a doornail - I BELIEVE that with certain types of jigs (potentially not the standard one) the device will turn on without a battery so this could be confirmed. If so, you might be able to fix it with a new battery OR topping off the battery in an external charger.
2) Total hardware failure of some sort, highly likely going beyond a brick.
Click to expand...
Click to collapse
I went to an AT&T store and the guy tried several batteries. How could it be hardware when all it was doing was charging...While I was asleep and not touching it at all.
you can try reading this.
http://forum.xda-developers.com/showthread.php?t=1336359
qkster said:
you can try reading this.
http://forum.xda-developers.com/showthread.php?t=1336359
Click to expand...
Click to collapse
this exactly!!... take your time ..do it right...you can do it....
o wait thats a song!!!
but seriously ..read it ALL!! and follow instructions very carefully ..i had to download ubuntu.. my phone "died" just a blank screen and this got me back!!!
good luck !!
Like I stated before. Mine did the same thing. Black screen, no power, 3-button didn't work. My jig popped in into download mode, and GTG's unbrick from there. I leanred a long time ago, to always have my jig with me. Love my jig! Thanks MTV! best $8 I ever spent.
I'm sure you tried this but I actually never use three buttons to get into download mode. I just insert the battery, hold down the two volume buttons and, while holding the buttons, I plug in the usb that's plugged into the computer. Flame me if this is obvious but I didn't see anyone suggest it.
hey faux ..how long have you had this phone and how long have you been with ATT?
JUST MAKING SURE... You have kies installed on your computer right???
Sent from my A500 using Tapatalk
Had the phone about 6 months...att for 3 and a half years. IDK what "Jig you're talking about or else I might try it if I can easily get one today and it doesn't have to be shipped. I'd rather not try the unbrickable thing because my phone as of right now is in warranty I'd rather not void it. And yes I did the two button DL mode. Not 3.
Erik_T said:
JUST MAKING SURE... You have kies installed on your computer right???
Sent from my A500 using Tapatalk
Click to expand...
Click to collapse
Yes I do have it installed.
Im trying to explain everything to prevent unneeded questions
I have viewed several threads about this but absolutely none with an answer. My Samsung Infuse 4g with at&t (nonrooted) is in a bootloop. The cause of this was my every-other-day reboot. Once I turned it back on it goes to the samsung screen for about 5 secs, then goes black, then says samsung again and so on repeatedly. I pull the battery and as soon as it makes contact back with the phone it turns on by itself into the same Samsung screen over and over. When plugged into wall or computer it will show the charge screen where there is no battery life left, then it will flash and start up the charge screen again and so on just like the samsung screen. I cannot go into download mode (the buttons, at this point, do nothing. No response)
I have tried taking the battery out and plugging in usb cable to computer, then holding both volumes and putting battery in=charging loop
↑ with volume up=charging loop
↑↑ with volume down=charging loop
computer doesnt detect it, adb cant find it, cannot go into download mode, odin cant see it, heimdall cant see it, cant actually boot into anything, cant leave battery in or else phone will restart itself the entire time, and this was caused by my (already gbread) infuse 4g doing a regular reboot (aka power button, tap power off, after phone is confirmed off take battery out, battery back in, turn on)
Recommendations at this point? on a scale from 1=noob to 10=expert im a 7 on this type of thing. Ive always heard that as long as you can boot into a picture its only soft bricked but if i was right i wouldnt be here. Any and all help would be much appreciated. If you need me to post a video I would have NO problem doing that showing everything im doing.
oh, and by I have viewed several threads about this i meant that i have only been able to find 1 thread about it and 2 links that didnt work for me but might for you
link that worked- http://forum.xda-developers.com/archive/index.php/t-1354731.html
links that did not-
http://www.google.com/url?sa=t&rct=...ih1Zf_BvtcIbJXGEw&sig2=jjOcukFWr9sPWJZH1rlhnA
http://www.google.com/url?sa=t&rct=...ih1Zf_BvtcIbJXGEw&sig2=SZeMzIF2hnjdkk6GPDkovg
You might have already tried this way, but I've always held down both volume buttons first before plugging in the USB cord - not the other way around. You can also try different cords, different USB ports and/or different computers.
Mine was doing this the other day and it turned out to be my SD card being flaky. Maybe try taking it out and booting?
Radiotsar said:
You might have already tried this way, but I've always held down both volume buttons first before plugging in the USB cord - not the other way around. You can also try different cords, different USB ports and/or different computers.
Click to expand...
Click to collapse
Ive tried a hp touchpad cord, an atrix cord, and the original cord. I cant really do the button combo because as soon as the battery makes contact the phone turns on. thats why i had the usb cord in first to see if it worked. ive tried every usb port and 2 different laptops, the computer wont recognize it if the phone wont go past the samsung start up screen
J101 said:
Mine was doing this the other day and it turned out to be my SD card being flaky. Maybe try taking it out and booting?
Click to expand...
Click to collapse
I've taken the card out and used a different card, nothing. Tried taking sim card out, nothing.
I should have been clearer. Leave the battery out of the process until after attaching the cord and the screen coming up.
Sent from my SGH-I997 using xda premium
Radiotsar said:
I should have been clearer. Leave the battery out of the process until after attaching the cord and the screen coming up.
Sent from my SGH-I997 using xda premium
Click to expand...
Click to collapse
I do, every time.
1. battery out
2. hold down volume buttons (any combo)
3. attach cord (nothing happens, no screen, nothing)
4. put battery in
Results= Charging loop
lifetaker said:
I do, every time.
1. battery out
2. hold down volume buttons (any combo)
3. attach cord (nothing happens, no screen, nothing)
4. put battery in
Results= Charging loop
Click to expand...
Click to collapse
should be the same...wonder if you battery needs to be charged first, it should be fully charged at best...to do any flash/Odin/one click
this how I do it...basicly the same..
>take batt out
>plug in usb cable...to both phone and computer
>hold both volume buttons...NO NOT HOLD THE POWER BUTTON....
>put batt in...
and bam should see the android dude shoveling in yellow triangle...
If you get no response from the usb without the battery, and inserting the battery indicates the battery needs charging - I'd suspect the phone's usb port. Especially after trying different cords & computers.
Sent from my SGH-I997 using xda premium
Sorry for the sometimes choppy video recording.
http://www.youtube.com/watch?v=QWKdGS_5_Ps&feature=youtu.be
Have you tried a jig you can buy them on ebay for 6-12 bucks or you can donate one of you old cables and make it your self..
http://galaxys2root.com/galaxy-s2-hacks/how-to-make-a-usb-jig-for-your-galaxy-s2/
this will/should get you into download mode
Hello.
I have the same problem... tried also everything now i gave it to cellphone shop, i hope you guys can give me answer before i am gonna waist $100
HELP?1
Help me please
I was in this state. There are two options I can think of. A JIG as mentioned previously or the Heimdall One-Click-Unbrick. The one-click unbrick did it for me and got me back to cmw and download mode, then i could flash to stock, root and flash up to ICS. It was really easy and I stopped sweating once it booted to cmw instantly after running it.
Joe
hello.
The problem is when i connect it to my computer its keep disconnecting and doing terreble noise, (windows noise) when you keep connecting and disconnecting USB cable
JIG DIDNT WORK, because the same problem.... maybe the chargging connect is broken? or has a corrosion?
Please use the Q&A Forum for questions &
Read the Forum Rules Ref Posting
Thanks ✟
Moving to Q&A
Sounds/Looks like a hardware issue...
Did it get any water damage in the past?
Hope you got warranty or still under warranty.
I am having exactly the same problem. My Infuse has never been rooted or unlocked (quite ironically, I was about to root it for the first time).
Boot loop when not plugged in, charge loop when plugged in. Absolutely no combination of buttons, inserting/removing the battery, and/or plugging/unplugging the USB has gotten it to do anything.
This has happened several times over the past few days. The first few times it sorted itself out in an hour or two. Today I couldn't get it to do anything at all.
I found several posts by people who have this problem, and it has never been conclusively solved from what I've seen. Finally one person said they fixed it by lightly smacking the phone with their hand. Lo and behold, it came on for about 5 minutes before looping again. So I smacked it again, and before it could re-loop, I factory reset it. A few hours went by and I was convinced that it was fixed.
A few minutes ago I had it plugged in to my computer via USB and was getting ready to SuperOneClick it. Then it went back into loop. I can't get it to come on this time. Again, no combination of buttons will send it into download mode. The computer can't see it. The battery is charged. The USB cable and port are fine. The software was reset earlier today. Does this mean that I have a hardware problem, or is there a software issue that could be fixable?
EDIT: So I decided to try hitting the power button, something that had never worked to this point, and the device came on. A couple minutes later it went back to boot loop. On a whim I tried download mode, which had stubbornly refused to work all day. Of course it immediately worked. Not really knowing what to try, since I'd already wiped user data, I wiped cache data and formatted the internal SD. Then I told it to reboot. Back to boot loop. A few minutes later, it came back on with the power button. Two minutes later, boot loop again. Then it restarted of its own accord. And now back to boot loop. I just don't even know anymore.
EDIT2: Just a thought... Something is weird with the power button. Whenever the phone is on and I hit power (briefly, not holding it down), it goes to the shutdown menu as though I'd held it down. A few seconds later, I'm always back in boot loop.
Infuse loop
I have found the problem. It is, in my case, the power button. I removed the case and crossed terminals with a paperclip. BAM. Booted up, and when I removed the paper clip.... back to boot loop at Samsung logo.
There is a place to send the phone. Ive see great reviews.
mobiletechvideos.mybigcommerce.com/samsung-infuse-4g-power-button-repair/
Seems like there has been a string of power button malfunctions going around lately. There are a few threads going on where people have had this issue. Sometimes its just the terminals needing to be cleaned or dust blown out.
Hey Gang! I have a not so common issue, from what I have searched and read.
I'm trying to fix a friends Infuse 4G from looping at the Samsung screen. Also the phone would power loop when battery is inserted and charge loop when plugged into the USB Cable. Nothing I have tried has worked.
Tried:
1. 3 button to CWM Recovery. FAIL
2. Volume up/dn held then plug USB in for download mode. FAIL
3. Plug in the USB with no battery, hold volume up/dn, insert battery for download mode. FAIL
Ok... now being really familiar with electronics, I made a JIG from a tutorial and here is the fun part for those that want to help out....
I plugged the JIG in, inserted the battery and behold... I got the download mode screen... but it too is LOOPING!!!!
So I tried a quick switch. Inserted JIG, Inserted battery, got the download mode screen and before it looped, I replaced the JIG with the USB Cable. FAIL! It started looping with the Samsung screen.
I am stumped! Can anyone help out or know how I can get past this issue so I can Odin or flash back to stock without backtracking to what I have already done?
Thanks in Advance,
Scott
zeroplace said:
Hey Gang! I have a not so common issue, from what I have searched and read.
I'm trying to fix a friends Infuse 4G from looping at the Samsung screen. Also the phone would power loop when battery is inserted and charge loop when plugged into the USB Cable. Nothing I have tried has worked.
Tried:
1. 3 button to CWM Recovery. FAIL
2. Volume up/dn held then plug USB in for download mode. FAIL
3. Plug in the USB with no battery, hold volume up/dn, insert battery for download mode. FAIL
Ok... now being really familiar with electronics, I made a JIG from a tutorial and here is the fun part for those that want to help out....
I plugged the JIG in, inserted the battery and behold... I got the download mode screen... but it too is LOOPING!!!!
So I tried a quick switch. Inserted JIG, Inserted battery, got the download mode screen and before it looped, I replaced the JIG with the USB Cable. FAIL! It started looping with the Samsung screen.
I am stumped! Can anyone help out or know how I can get past this issue so I can Odin or flash back to stock without backtracking to what I have already done?
Thanks in Advance,
Scott
Click to expand...
Click to collapse
look in this q/a and the general section about power button failure...there are some solutions offered
qkster said:
look in this q/a and the general section about power button failure...there are some solutions offered
Click to expand...
Click to collapse
Will check it out and will report back. Thanks again
That's definitely a messed up power button. My power button is messed up also. About every 3 months, I have to just slam the power button on a hard surface and it goes back to normal. Just a quick fix if nothing else works or if you can't fix it.
Sent from my SGH-I997 using xda app-developers app
omar71693 said:
That's definitely a messed up power button. My power button is messed up also. About every 3 months, I have to just slam the power button on a hard surface and it goes back to normal. Just a quick fix if nothing else works or if you can't fix it.
Sent from my SGH-I997 using xda app-developers app
Click to expand...
Click to collapse
I may suggest tapping it or taking it out for a cleaning.
Or replacing it or even remapping it..there are 2 threads in the general section that is relevant.
I don't recommend slamming it though...what is good or omar's phone may not be good for zero's phone.
Lol valid point. Hope everything works out for you tho. Some people have gotten their power button fixed for cheap..don't know exact prices.
Sent from my SGH-I997 using xda app-developers app
USB jig not working
Galaxy s2-i9200g charges when i plug it in charger,but not able to start and not able to go any mode(download or recovery) so used USB jig,- Fail not able to go to download mode
When i insert the USB jig it goes to infinite loop with showing a symbol of battery upload with blank battery
When i swith on the phone i get the logo and stuck there
what is the solution for this when usb jig is not working