Hi everybody,
i have a htc hd2, it was running on windows mobile and i wanted something new so i decided put android on it.
So i did i ran iit it worked great, not problems.
after a month it started freezing up so id just reset it and it was ok for a while.
than once i hard reset it, and it froze at the tmobile sign, since than it will not turn on.
i dont know what to do or how put something els on it.
PLEASE HELP ME!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
you might have had more luck if you posted in the HD2 forum, but your in luck as i happened to be passing by!
Okie dokie, first things first, when you have issues with the HD2 its quite good pratice to revert it to factory defaults, problems can come from the ROM, radio or SPL or any other things popped in there, like magldr for example.
so getting rid of it all and starting again is usually a good start.
its not always nessary mind but its probably worth it
But before we do that, try hard reseting it or flash it with a new ROM, this can be done in bootloader or magldr depending on how you installed Android
if you want to revert to factory defaults
1.) Reformat SD card to FAT32 (use the panasonic SD formatter, low level format with delete)
2.) Find and downloaded an original stock rom for your device
3.) Extracted "RUU_signed.nbh" from the ROM
4.) Transfer it to SD card, do not place in any folders
5.) Renamed it "leoimg.nbh"
6.) Inserted SD card into phone
7.) Turn on the phone into bootloader mode (tri-colour)
8.) Follow directions
To get bootloader to work Turn off phone or pull the battery, hold down the "VOL down" button and turn back on again) (continue to hold the vol button down until you get the tri-colour screen)
With a bit of luck it will detect the SD card image, follow the directions and flashif its not detecting the SD card then connect your PC to the phone (it will install some drivers) and then run the original stock ROM exe file.
EDIT, to hard reset turn off device, hold down "VOL up" AND "VOL down" turn on again (hold the VOL buttons down until the tri-colour screen comes up)
if your using magldr turn off the device, hold down the "phone" button and turn on (keep holding down the phone button until magldr comes on)
What about your ROM, radio version and so on ?
Related
I used the rom cooking kitchen to make some of my favorite roms even better. Basically I just deleated some of the programs I dont use and deleated some of the extra sounds. Everything went through without any problems and now after I flashed it the smart mobility screen comes up and shows the radio and other info but then freezes there. How can I fix this or go back to a different rom? HELP. Thanks again
hollywood said:
I used the rom cooking kitchen to make some of my favorite roms even better. Basically I just deleated some of the programs I dont use and deleated some of the extra sounds. Everything went through without any problems and now after I flashed it the smart mobility screen comes up and shows the radio and other info but then freezes there. How can I fix this or go back to a different rom? HELP. Thanks again
Click to expand...
Click to collapse
try and get the ship rom that came with ya phone i had the same prob with a o2 xda/mda wizard i got the rom whitch was 1.05 ok now
hope this helps
How can I install it, my usb wont connect to the device?
hollywood said:
How can I install it, my usb wont connect to the device?
Click to expand...
Click to collapse
read the hard spl manual
*MICROSD FLASHING*
***IMPORTANT***
Please make sure you have HardSPL on your device.
1. Get a 128MB MicroSD card (or whatever size you like) and format it (***please make sure you format it, but not just delete all contents on it)
2. find the ROM image you would like to use, normally namede RUU_Sign.nbh, and rename it to "KAISIMG.nbh"
3. Plug the card into the phone, then enter boot loader mode by pressing down the Power and Camera buttons simultaneously, and using the stylus at the same time to press the RESET button at the left side. Continue pressing the two buttons for a few seconds after pressing and releasing the reset button until the bootloader screen appears. (taken from Wiki)
4. You will first see a tri-color screen then the information on the card. Press power button to start flashing.
5. After all these are done, press the reset button located at the bottom of the phone to reset the device.
Thank you very much, back to normal!
AFTER UNLOCK NO VOICE OR SPEAKER WORKING I JUST FLASHED WITH
(RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27.04.15_Test) NOW PHONE DOESNT
POWER UP OR BOOT MODE BLANK SCREEN
I TRY TO CONNECT TO THE COMPUTER ASKING DRIVER (DATE INTERFACE)
I NEED YOUR HELP TO GET BACK LIVE
PLEASE
THANKS
How did you unlock it? Did you CID unlock? HardSPL version? Can you get to the bootloader by holding down the camera button and power button and soft reset at the same time?
From the sound of things you loaded a CID locked rom onto your locked phone. This is only a guess though based on the fact that the ROM you loaded included a compatible radio.
Just a tip, next time don't use all caps. It's considered shouting and inappropriate. We understand your urge to get it fixed so we'll help even without the caps
Answering Alibaba0101's questions will help a lot. Also, have you tried taking the battery out and putting it back in?
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
lxa786 said:
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
Click to expand...
Click to collapse
I don't see the step where you flashed your original radio back after doing the SIM unlock. The radio that you is a special "patched" radio, and the phone will not successfully boot into Windows with it flashed.
Go into the bootloader (hold Camera during power on), and flash a compatible radio. If you haven't flashed a cooked ROM yet, then just hit up the Kaiser Wiki and grab the original ship radio for your phone.
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
austinsnyc said:
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
Click to expand...
Click to collapse
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Boot Loader
Same here I just hold down camera button and soft reset works every time.
hi I need your more help how can I get phone on boot mode phone dead not responding I tried more then 10 time by pressing camera and power button phone still blank screen.
No display show so how can I flash the phone
Any idea to flash the phone dead mode?
thanks
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
This has gotten people in the past, so sorry if it sounds dumb.
The Camera button has two settings Full Press and Half Press. Press until it stops then press again. You need to be pushing the Camera Button down all the way to get into Bootloader.
Also I never need to press the power Power Button As well.
I may be wrong but, when the phone is on, you can press the Camera and Soft Reset buttons. When the phone is off, you press the Power, Camera, and Soft Reset buttons to go directly into boot loader.
i tried but screen still blank no light nothing when i put usb into the phone asking driver (data interface)?
Can not go in bootloader help?
Tytn 2 is dead .
Ok last night I try to install the new hyperdragon III BlackStone rom everything is fine untill it finish and it cant load in to window, the computer keep asking me for the data interface and the tilt keep restart and the screen only shows hyperdragen III. I was running hyperdragon III opal (10/11/08) I tried MMTY and reinstall the OE rom but no luck, please help!!
Tytn2 Dead or not??
Tytn 2 is dead if you see data interface driver when put in usb cabel install v3 motorola driver and you will see data qualcomm usb driver i device manager .... this mean that totaly erased memory in tytn2 and its dead,only with jtag can flash again.
Please, tell me how can y do it. I have the same problem....
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Click to expand...
Click to collapse
I don't see any step about using the white screen fix so I'm guessing you didn't successfully install HardSPL and then after that you tried flashing a ROM whilst being oblivious to the fact that Hard SPL wasn't installed, so you most likely bricked your phone
AllTheWay said:
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Click to expand...
Click to collapse
Dead HTC KAISER
Hello My friends
After along search and Googling on the net without finding any solution. at last I did took a Risk to solve and save my DEAD HTC KAISER . what i did is I ressembled the HTC KAISER , to see if my USB data input was defect, but it was Good, now .......he he.. what i fond avery smal Batterie planted on the motherboard , i took it of the the board , end waited 1 hour . then i place it back , assembeled my HTC KAISER back
Taaaaraaaaa my HTC KAISER Power Led went ON ,,, YES ..Friends . is charging .
after 1/2 hour , I swish the HTC on ,,,, heeeee Is working......flash it with the new ROM wm 6.5 ...really it went Perfect.. end My HTC KAISER... ALIVE AGAIN.
Greatins , and hoppe this will Help you..........Good Luck .
on youtube you can find videos how to dissembele your HATC KAISER.
thanks to XDA-Developers , for this great Forum.
ericc191 said:
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
Click to expand...
Click to collapse
my kaiser boots up but after the att thing the screen gos black do you know how to fix this
i was following this guide:
http://forum.xda-developers.com/showthread.php?t=448008
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 using a PC (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Raphael Rom Develpoment Page and unzip/unrar it to your computer
3. Goto the Roms Folder and rename the .nbh file to RAPHIMG.nbh
4. Copy the RAPHIMG.nbh file to the root of your microSD Card
5. Remove Sim Card and Restart phone
6. Plug the microSD Card into the phone
7. Press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears
8. Follow the onscreen instructions to start flashing
9. Once phone finishes flashing and says Update Complete, reset with the stylus
10. When it gets to the screen where it configures the stylus, HARD RESET
(hold the VOLUME DOWN and ENTER (center) Buttons, press the RESET button with the stylus tip, then release the RESET button but continue to hold the VOLUME DOWN and ENTER buttons until the reset screen appears)
11. Follow onscreen instructions to set up your New Rom
fine upto step 8, it goes to the tricolour but then it just stops and it says
RAPHL100
SPL-1.90.0000
MICRO-RAPH (LED) V13
MICROP-RAPH (KEY) V5
PSOC-RAPH STAGE_CVT V0X36
and it just crashes....anyone help me?
FORGOT TO ADD:
It goes to a grey screen and says ' no image file'
This is the guide you should have used.
Sounds like you tried to flash your phone before you Hard SPL'd it.
Good luck!
IMO, USB isn't the best way to flash, because of
- not installed USB drivers for device in bootloader mode
- accidental desktop sleep or usb unplug
SD flash though
- corrupt SD card
- those microSD cards accidentally get dislodged and thus bad flash
i think that the best way is to flash via USB and make sure all drivers are installed... don't touch the computer or phone when it's flashing (maybe move the mouse a bit to prevent screensaver etc.)
I have downloaded kaiser-HardSPLv1, i ran it on the pc.
and i got to step 2, it said
http://img297.imageshack.us/i/htc.png/
my phone turns of, then turns back on again and i dont see the tri colour help please!
iraqi4life said:
I have downloaded kaiser-HardSPLv1, i ran it on the pc.
and i got to step 2, it said
http://img297.imageshack.us/i/htc.png/
my phone turns of, then turns back on again and i dont see the tri colour help please!
Click to expand...
Click to collapse
Your phone is NOT a Kaiser, its a raphael.
You really should have read the guide I pointed you to.
It had the link to the correct SPL for your device.
A little time to read would save you hundreds of $
You may find a fix ( there is a hit and miss solution for this) but you really need to search, read and learn.
Start with this thread.
ah okay thanks alot man, i appreciate you're help.
ive done all that, i get the error {262} it stops at 0% for a few mins then displays the 262 error, i have turned of firewall and ive searched the forum, but no avail?
Okay, i tried to do the hard spl with the sim card and memory card out
but still no avail, ive turned off the firewall and then i ran
RaphaelHardSPL-Unsigned_190_1_3 but still can 262 error, please help this is very frustrating!
what happens is that i run through the steps on the RRU, then the phone goes to a black screen, and the progress bar appears, stays at 0% for 2-3 mins then error 262 appears
please help!!
Okay, i have now successfuly hard SPL my phone.
however, i have inserted a ROM in my micro SD hard, pressed volume down and then clicked reset, however i can only see the tri-colour screen and it still says no image .
please help!
OMG
i think i have bricked my phone,
i turn it on and it goes to the TOUCH PRO screen, then nothing happens
ive done it! it worked on the other pc!!! yay
i am using the energy rom standard.
and also, which one has the theme which has it like this:
http://lh3.ggpht.com/_obTK4UolmtY/Sjo8vSiryNI/AAAAAAAAAPg/XBDAHTFuBJw/NRG_3.0_Today.jpg
does it work with the raphael ?
Hi guys,
I'm having kind of a big issue. I went for a drive on my motorcycle and it started to rain. My touch pro was in my jacket and got wet.
When I came home, the screen was black and I couldn't get it on. I took out the battery and reinserted it, pressed on and it booted (I felt the vibration that it returns when booting and my keyboard was lightened up) but screen stayed black.
My phone is still under waranty but I installed the energyROM so that voids the warranty. I want to reset it to stock but the problem is that I can't enter my PIN because the screen is black so the phone won't boot and I can't access it with my PC
Any ideas?
Thanks in advance!
Greetings
Get an emulator like Pocket Controller or My Mobiler and you can do it from your desktop.
Also, putting the phone in a bag of rice will evaporate all of the moisture.
I don't see what the emulator can do for me
I can't access the device with ActiveSync since I had it set to "use as disk drive" and I can only see it as disk drive now. (which I couldn't five minutes ago, weird :s)
just connect your device with usb and go into the bootloader by holding volume down and pressing the reset switch. the device will connect to active sync and you'll be able to flash back to stock again
I can't see to get in the bootloader by doing a hard reset
The emulation software also didn't help, they didn't find my phone because of a missing ActiveSync connection.
No, what naKruul means is that you load the .nbh file from the stock ROM to the root of your storage card (search flashing from storage card) and rename it to raphimg.nbh (or whatever it says in the flashing directions), use hardware keys to enter bootloader (PWR/VOL DWN/RESET) then the stock ROM will flash to your device, theres no need to see anything other than knowing what button confirms the flash, which should be in the flashing directions as well.
I think I succeeded in flashing it but I'm not sure.
I followed the instructions as mentioned in the HardSPL thread.
Now when I plug the phone in, I see a file called EncFiltLog.memc on the card which wasn't there before, so I assume something happened. But still the phone is not connecting to activesync, it connects as storage drive.
The daemons don't work either because of the lack of the activesync connection.
So you reflashed HardSPL or the stock ROM?
What you need to do is get the stock ROM back on your device, which should in theory fix your active sync issue, so you will be able to flash back to StockSPL for your warranty return.
Either way, if the screen is out and your covered for water damage, they'll never know what you flashed.
This is what I did:
1. I downloaded the stock *.nbh provided in the HardSPL thread
2. Formatted my SD Card to FAT32
3. Renamed the nbh to RAPHIMG.nbh and copied it to my SD Card
4. Pressed the volume down button and enter button the same time an pressed reset with the stylus.
5. Wait a minute
6. Pressed volume up
7. Waited about 5 minutes
8. Reconnected the device.
How big is the .NBH file?
volume down + enter key + reset switch is hardreset, not reflshing the device. reflashing is done by just pressing volume down + reset switch
It's 514kb
Hello
I had HTC Diamond before and now i bought HTC Touch Pro.
It has original O2 rom and I am trying to flash a new one. But I cannot enter bootloader. I did Hard-SPL but since i cannot enter bootloader I cannot check if it was succesful or not. I tried all the button combinations (like vol down + enter + reset etc...) but it was unsuccesfull. And i even tried to copy EnterBootloader.exe to the phone and run it. But the screen just goes black and thats all. And when I was trying to do HARD-SPL the screen also went only black. I never seen the three color screen. Please help me!
Thanks
Moved as not ROM Development.
Well, you're probably doing it wrong. Hold volume down, then soft reset. Keep holding vol down until the tricolor screen appears. Don't hold the reset button down; just push it and release it.
Im doing it right. Im sure
so u re trying to flash via card or not, if you're trying to flash via PC dont forget to connect with active sync before, if you are trying to connect with SD card dont forget to do a clean format of it before
I remembered that I actually had the issue once (no idea why, it only happened on one rom about a year ago). Try doing a hard reset, then go into bootloader (instead of pushing vol up and re-booting). If that doesn't work, then start the boot process, and when it hits the alignment screen, try to go into bootloader.