[Q] changing Button 3 (Camera) to <None>-need explanation - P3470 ROM Development

i have the files/steps to flash pharo p3470.steps as below
1. Transfer the extracted files (JumpSPL.exe & Pharos_JumpSPL.nb) to your device and execute.
2. Use 0x10000000 as Jump Address.
3. After getting the Open File Dialog, press [Camera] & [Power] like you are going to enter Boot Loader, then tab on the Pharos_JumpSPL.nb file (Pharos_JumpSPL.nb).
You will get the grey background screen, you can flash any ROM to your device at this point.
In some case, you may need to unplug and then plug the USB cable again.
4. If you wanted to permanently unlock your device, why not, simply flash it with the HardSPL once and you are done.
After HardSPL, you will notice your SPL version change when boot;
From SPL 1.11.0001
To SPL 1.11Mobiz
Recommended:
""""""" To make it easier, I recommend changing Button 3 (Camera) to <None> or the Camera may disturb you"""""
did not understand above sentence
-so can not flash-help me
thank u

Related

Kaiser Not Working

Hi Im Using Xp Pro
THIS IS WHERE IM UP TO .SORRY IM NOT USED TO FORUMS.NEWBY.[please scroll to bottom of page]
The exe has created a folder on your C drive called Unlocker. There are 2 folders inside that one called kaiser-HardSPLv1 and one called kaiser-simunlocker
Note for Vista users
===============
If you do not have the latest version of Mobile Centre follow This guide to explain how to change your drivers to the xp. You will have problems running the unlocker otherwise. Log in as administrator if you run the ROM update tool and unlocker. That also applies to XP users.
Instructions
============
1. Install HardSPL as per the instructions:
1- Connect Kaiser to computer using USB cable
2- Make sure ActiveSync icon is GREEN
3- RUN kaiser-hardSPL.exe on Computer (PC)
4- Follow instructions on screen
To check it has installed correctly, power off and then press power on while keeping camera pressed, this will enter the so called bootloader mode and you see a tri-colour screen (Red, Green, Blue). You should see "SPL-1.0 OliPof" on the second line in the top left corner. You can exit this mode by means of a "soft reset": press the reset button with the stylus.
2. Make a note of the radio version that is currently installed. You see the version strings in the splash screen which appears soon after power on (e.g. "R 1.27.14.09") (Or by going to Start, Settings, System, device information). Since we will flash a special radio in step 5 you need to flash back your original radio in the last step. (If you have a UK Orange Tytn II with the radio version 1.27.12.29, Use Radio version 1.27.12.32. Keep a note of the unlocking Code as you will need to enter it again after you have re-flashed the Radio.) (You will find download links at the bottom of the instructions)
3. Connect PC and Kaiser with a USB cable and keep it connected until the last step.
4. Power on the Kaiser and let it boot into Windows Mobile. On the PC make sure the activesync icon is green
5. After you unpacked the download you see directories "step1" and "step2". Go into "step1" and run KaiserCustomRUU.exe. This will flash the special patched radio rom. Follow the instructions until it is finished.
6. Power off your Kaiser and insert a different SIM, i.e. a SIM from another provider than the one your phone is locked to. (if you have a pin on the sim disable it first)
7. Once Windows Mobile has booted up it will (usually after you have entered the usual 4-digit PIN) show a window called "Simlock" and a textbox where you can enter a 8-digit unlock code. Now perform a soft reset by pressing the reset button *but* at the same time keep the camera button pressed. If you did it well you will be back in bootloader mode and you see the tri-color screen. The best technique is to press and hold the camera button first and then shortly press the reset button with the stylus.
8a. right-click activesync icon and uncheck "Allow USB connections" from Connection Settings
8b. On your PC, go into the "step2" directory and run "kaiser-simunlocker.exe". If all went well you will see the unlock code on your monitor and your Kaiser is being restarted
MY KAISER DOES NOT RESTART and stays in tri mode AND THERE IS NO PASSWORD ON SCREEN.THANKS AGAIN
mattdehat said:
HI,ive been installing sim unlock on my tmobile kaiser and at a certain point i get a problem,after tri-screen after soft reset with camera button pressed,on screen i get this
===kaiser sim unlocker[c}2008 by jockeyw2001
===donations happily accepted. paypal to [email protected]
WITHOUT THE PASSWORD.CANT UNDERSTAND IS SHOULD HAVE A PASSWORD AND AS EVER NOT HAPPENING FOR ME
ANY HELP WOULD BE APPRECIATED.THANKS
Click to expand...
Click to collapse
are you using vista? could you be a bit clearer on things? less caps?
Hi Im Using Xp Pro
THIS IS WHERE IM UP TO .SORRY IM NOT USED TO FORUMS.NEWBY.
The exe has created a folder on your C drive called Unlocker. There are 2 folders inside that one called kaiser-HardSPLv1 and one called kaiser-simunlocker
Note for Vista users
===============
If you do not have the latest version of Mobile Centre follow This guide to explain how to change your drivers to the xp. You will have problems running the unlocker otherwise. Log in as administrator if you run the ROM update tool and unlocker. That also applies to XP users.
Instructions
============
1. Install HardSPL as per the instructions:
1- Connect Kaiser to computer using USB cable
2- Make sure ActiveSync icon is GREEN
3- RUN kaiser-hardSPL.exe on Computer (PC)
4- Follow instructions on screen
To check it has installed correctly, power off and then press power on while keeping camera pressed, this will enter the so called bootloader mode and you see a tri-colour screen (Red, Green, Blue). You should see "SPL-1.0 OliPof" on the second line in the top left corner. You can exit this mode by means of a "soft reset": press the reset button with the stylus.
2. Make a note of the radio version that is currently installed. You see the version strings in the splash screen which appears soon after power on (e.g. "R 1.27.14.09") (Or by going to Start, Settings, System, device information). Since we will flash a special radio in step 5 you need to flash back your original radio in the last step. (If you have a UK Orange Tytn II with the radio version 1.27.12.29, Use Radio version 1.27.12.32. Keep a note of the unlocking Code as you will need to enter it again after you have re-flashed the Radio.) (You will find download links at the bottom of the instructions)
3. Connect PC and Kaiser with a USB cable and keep it connected until the last step.
4. Power on the Kaiser and let it boot into Windows Mobile. On the PC make sure the activesync icon is green
5. After you unpacked the download you see directories "step1" and "step2". Go into "step1" and run KaiserCustomRUU.exe. This will flash the special patched radio rom. Follow the instructions until it is finished.
6. Power off your Kaiser and insert a different SIM, i.e. a SIM from another provider than the one your phone is locked to. (if you have a pin on the sim disable it first)
7. Once Windows Mobile has booted up it will (usually after you have entered the usual 4-digit PIN) show a window called "Simlock" and a textbox where you can enter a 8-digit unlock code. Now perform a soft reset by pressing the reset button *but* at the same time keep the camera button pressed. If you did it well you will be back in bootloader mode and you see the tri-color screen. The best technique is to press and hold the camera button first and then shortly press the reset button with the stylus.
8a. right-click activesync icon and uncheck "Allow USB connections" from Connection Settings
8b. On your PC, go into the "step2" directory and run "kaiser-simunlocker.exe". If all went well you will see the unlock code on your monitor and your Kaiser is being restarted
MY KAISER DOES NOT RESTART AND THERE IS NO PASSWORD ON SCREEN.THANKS AGAIN
so what step did you get up to?? you didnt really need to paste the whole instructions as most of already know the steps.
hi.istarted fresh.phone now unlocked.many thanks to all.I LOVE THIS SITE...MOST INFORMATIVE.MANY THANKS AGAIN
I got stucked into a Multi dotted colored screen with my Kaiser8925, and I can´t flash the old radio versión, I got the file, but I try to flash my kaiser, and it gets not installed, I think the new radio version I flashed is causing the problems. ¿Can you help me?
josereja said:
I got stucked into a Multi dotted colored screen with my Kaiser8925, and I can´t flash the old radio versión, I got the file, but I try to flash my kaiser, and it gets not installed, I think the new radio version I flashed is causing the problems. ¿Can you help me?
Click to expand...
Click to collapse
Thread hi-jacking is not very good...also posting the same thing in multiple threads isn't either...But, try reinstalling your Windows rom...Sounds like thats the issue. Could be something more severe though.

Custom RUU Issue

I was trying to flash my phone to a diffent ROM< but now everytime that i have tryed, it gives me an error - get newer updater. I have used CUstom RUU V. 1 that comes with most roms, and i have used the 5.22. The Hard SPL version is 1.00liPof. Help!!!
I think you may have the wrong section, what phone are u using, i dnt thats a kaiser hardspl
Hard SPL 1.00lipro is a hardspl for the kaiser, i have it on my kaiser. Although the 5.22 he refers to i have no idea what they mean?
Opening poster try to explain in more detail what it is that you are trying to do, i.e. what rom it is that you are trying to install, what windows you are using on your pc etc.
If you cant use that ruu try this one i attached
Ah i see, ive never really had that problem even though ive flashed on xp, vista and 7. Very weird. Try changing Hardspl.Good Luck and use the ruu that has been given here
had that problem
When i switched to windows 7 i had a similar issue. There should be an update now that you plugged your phone in to the c. Try to see if there is a windows update that shows up now.
Hi,
Or Even try to mount a virtual machine in Xp with Vmware or similar...
Good luck
Sat
Update your hardspl to 3.29 or 3.34. The spl you are using is for WM 6.0
http://forum.xda-developers.com/showthread.php?t=498320
sd
flash via micro sd. easy, faster, gets rid of a middle man. and update your spl.
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Kaiser Rom Develpoment Page and unzip/unrar it to your computer
3. Goto the Roms Folder and rename the .nbh file to KAISIMG.nbh
4. Copy the KAISIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Hold in the Power and Camera buttons, then press the reset button with the stylus for about 3 seconds until the BootLoader screen appears
7. You will first see a tri-color screen with the phone and SPL Information at the top
8. A message will then pop up asking you to press the Power button to start the update
9. Press power button to start flashing
10. Once phone finishes flashing and says Update Complete, reset with the stylus
11. When it gets to the screen where it configures the stylus, HARD RESET
(press left and right softkey buttons on the front and hold in reset with stylus until message appears)
12. When prompted, Press "Send Button" (Green Call Button on Front) to Clear Data
13. When prompted, Press "Send Button" (Green Call Button on Front) to Restart Phone
14. Follow onscreen instructions to set up your New Rom​
(from http://forum.xda-developers.com/showthread.php?t=433835)
i use windows seven and have never had any issues flashing roms?
A few kitchens dont work in seven though, so building is a bit hit and miss but flashing has never been a problem

Flashed or Not

Hi it seems like I need to do a new thread for this, I just need answers thank you
*upon checking my phone
I have this
ROM Version: 3.29.707.0 WWE
ROM Date: 05/07/08
Radio Version: 1.65.16.25
Protocol Version: 25.83.20.02H
and as I learn to check what Hard SPL is installed in my device (thanks to you guys ) it says 3.29. 0000 or something like that, so my question is... does my phone already have been flashed? if so can i skip to to loading the Rom i wanted, i do need help thanks
if not this is from mskip
1. MAKE SURE YOUR KAISER HAS AT LEAST 50% BATTERY POWER FIRST
2. Download and Unzip *THIS* File
3. Flash HardSPL 3.29 [ESSENTIAL]
Flashing via ActiveSync with USB Lead
1. Copy JumpSPL1.56-KAIS.exe, JumpSPL1.93-KAIS.exe and JumpSPL1.94-KAIS.exe to your device memory (NOT STORAGE CARD)
2. Pull out the battery and reinsert it (this step IS important) *DONT turn phone back on yet*
3. REMOVE SIM and SD CARDS!!
4. Turn phone back on and let it boot back into your operating system
5. Connect your phone to PC with a USB cable and wait until it syncs with your PC
6. Run File Explorer on your phone, browse to where you copied JumpSPL1.56-KAIS.exe on your device and run it (make sure the USB cable is still connected). If you get a white screen then reset your device and now try JumpSPL1.93 and lastly try JumpSPL1.94 if that one doesnt work.
7. CLick Continue on phone when prompted
8. After a few seconds the tri colour screen will appear on the phone and "USB" will be displayed at the bottom
9. Unplug the usb cable for 30 seconds and then Replug (phone will not re-sync but still says "USB" on the screen)
10. Right click on the Activesync icon in the bottom corner icon on the computer, goto connection settings, deselect "Allow USB connections" and click "ok"
11. Run the KaiserCustomRUU.exe file on your PC thats in the same folder as the HardSPL .nbh file and follow instructions (ticking boxes and clicking Next) *DO NOT re-enable USB Connections in Activesync*
12. Update will goto 100% (should take less than a minute), the Congratulations screen will be displayed on the PC and the phone will restart
13. Unplug USB cable from phone then REPLACE SIM and SD CARDS !!
14. Restart phone
*Remember to re-enable "Allow USB connections" in Activesync connection settings after a successful flash*
Flashing via MicroSD Card using cmonex HardSPL 3.29 [OPTIONAL]
FOR UPGRADING HARDSPL ONLY!! THIS WONT WORK UNLESS YOU ALREADY HAVE HARDSPL ON YOUR PHONE
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download Cmonex's HardSPL 3.29SD, unzip it and copy the 2 files into the root of your MicroSD Card
(KAISDIAG.NBH is basically an SSPL patched to load from SD without booting OS)
(KAISIMG.NBH is cmonex HardSPL 3.29)
3. Insert the microSD Card into the phone
4. Hold in the Power and Camera buttons, then press the reset button with the stylus for about 3 seconds until the BootLoader screen appears
5. It should say Loading / Update in progress and then to a screen saying SPL 1.00.OliNex
6. It should now say Press Power Button to flash or just flash the KAISIMG.NBH and then reset
7. At this point it should boot to the OS, if it doesn't then flash an OS (delete the previous KAISDIAG.NBH and KAISIMG.NBH from the SD Card and use Flashing Rom from MicroSD Card method)
8. After the Operating System loads, DELETE the KAISDIAG.NBH and KAISIMG.NBH files
*To check HardSPL version on your phone Enter Bootloader by Holding in the Power and Camera buttons, press the reset button with the stylus for 3 seconds until the tri-colour screen appears, then read the 2nd line which is the SPL version*
4. SIM and CID-Unlock [OPTIONAL]
For more reading go *HERE*
* YOUR DEVICE MUST BE SYNCHED WITH YOUR COMPUTER BEFORE RUNNING EACH STEP *
*Put your phone into Bootloader and update to a 6.1 Rom first if you get a black screen after Flashing the Patched Radio*
*If the program wont run u may need to install Microsoft .NET 2.0 on your computer to get it working*
1. Make a note of your current Radio in case you need to flash it back
2. Run KaiserUnlocker.exe, follow the instructions
(if you already have HardSPL on your phone you can skip straight to Step2)
3. After patched Radio has been flashed phone will restart and sync with the computer
4. On the Unlocker Program it should say Radio Patched at the bottom
5. Click on Step3 (Run Unlocker). This will bring up the Unlocker screen on your phone
6. If you want to check the status of your Sim Lock or CID Lock click the appropriate buttons
7. Click on Remove Sim Lock and Set CID, then click "Commit Changes"
* IF YOU DONT NEED TO FLASH A NEW ROM THEN PROCEED TO STEP6 TO PUT YOUR DESIRED RADIO BACK*
Click to expand...
Click to collapse
are the instructions from flashing hard spl 3.29 below it or what? I'm just confused coz' I found this tutorial here in the forums also http://forum.xda-developers.com/showpost.php?p=2498297&postcount=10
Im just confused thanks
If you are confused, stop.
Re-read again and again, until it makes sense. Understanding the huge material around here is not to be taken in only one day.
I spent my early days 2 weeks by merely reading, collecting tools (and patches) before even attempting to flash.
I just needed an answer if my phone's already flashed that's it if it is flashed could i skip now on flashing my desired rom? that's just it, just answers from experts. I'm reading btw.
any help will do
On bootloader will say Hard if have hard-spl.
You could have asked in teh thread rather than starting new so as to keep forum clean.
On that note thread closed.

[Q] Flashing MAGLDR

Guys, Help, I get to No 3 of the instructions listed below, the box disapears and nothing else happens, any tips on how to over come the problem, keep the suggestions simple please
1. FLASH MAGLDR TO YOUR DEVICE
The Original MAGLDR Thread by Cotulla is *HERE*
NOTE1: LEO512 and LEO1024 are both supported
NOTE2: MAGLDR doesn't replace OSPL/HSPL. It runs in the chain after. So it's safe to install and remove it
NOTE3: You can flash between 1.11, 1.12 and 1.13 versions on Magldr without losing your NAND Rom
1. Synch Phone with PC in Windows Mobile!!! It has to be connected to activesync or WMDC via USB cable
NOTE: As an alternative method to activesync you can restart your phone in Bootloader Mode, then connect the usb cable and wait until 'usb' appears in the bottom half of your phones screen
2. Browse to the folder you extracted your Magldr Package files to on your pc, right click on ROMUpdateUtility.exe and select Run as Administrator
3. Tick the box to confirm you are aware of the risks and select 'Next'
4. Tick the box to confirm you have followed the preperation steps and select 'Next'
* The program will now check the usb connection *
5. Select 'Update'
6. Verify the image you will flash (it should say 2.00.000.0) and Select 'Next'
7. Read the process list and Select 'Next'
8. Your phone will enter BootLoader Mode and the progress will goto 100%
9. Your phone will now Reboot. Congrats, you just flashed MAGLDR.
NOTE: To Enter MAGLDR Menu Screen after installation, Long Hold the Power Button when resetting the phone and the menu will appear

Unroot from Microsd help

I've looked every I'm running insert coin ics rom for the HTC sensation. The charger and the usb data slot is snapped i can charge but cant flash from the comp. Or read data from the phone.
I need to unroot from the microsd card back to stock ics in uk orange is this poss?? As i need my warranty back please help
I've found this post -
METHOD 2 - ENG HBOOT
Now the method I found to debrand (rather than messing about with CIDs), is using an ENG HBOOT, this is only temporary as the ROM we flash later on overwrites it.
Grab the file below (thanks to Bin4ry), and put it in the root of your SD Card. (i.e. if your on Windows, X:/ [where X is the letter of your Sensation's SD Card])
Quoteriginally Posted by Bin4ry
ENG Hboot:
[thanks Rahan95 for dumping ]
http://81.89.105.12/~bin4ry/hboot/PG58IMG.zip
Flash ENG HBOOT
1. EITHER:
1a. Shut down your phone, then take out your battery and put it back in.
OR:
1b. Make sure fastboot is disabled in settings and shut down your phone (This can be done via Settings > Power> Untick "FAST BOOT" at the bottom.)
2. Keep hold of the volume down button and switch your phone on.
3. When it asks "Do you want to start the update", press Volume Up to accept
5. Press Power Off to reboot back to normal homescreen
6. Remove PG58IMG.zip from your memory card
Download an RUU
1. You now need to pick the RUU you wish to flash, a good source is this thread:
http://forum.xda-developers.com/show....php?t=1074559
To debrand my Vodafone Sensation, I chose "RUU_Pyramid_HTC_Europe_1.35.401.1_Radio_10.43a.90 0 7.00U_10.51.9007.27_M3_release_198179_signed"
2. Once you have downloaded the RUU you would like to flash, run it (it can take a while to load), and stop when you get the welcome screen, which has a picture of a Sensation on the left and a red caution notice on the right.
3. Move this window out of the way (it forces itself into foreground), then open up windows explorer and go to:
C:\Users\[username]\AppData\Local\Temp
4. Then sort by Date Modified. Find the newest folder with a long random sequence of numbers as its name, go in here and you should see, three files and a folder: corecomp, dotnetinstaller, IBSEW64. (the files may be different on 32-bit OS), now go into the folder which has another long random name.
In there amongst a lot of files (use search if you need to), you will find rom.zip. This is the rom we want to flash!
5. Copy the rom.zip file to the root of your SD Card
(i.e. if your on Windows, X:/ [where X is the letter of your Sensation's SD Card])
6. Rename the rom.zip you just put on your SD Card, to PG58IMG.zip (ensure you do not rename it to PG58IMG.zip.zip or it wont work!)
7. Find the "HTC Android ROM Update Utility" Window, and hit Cancel.
THIS IS YOUR LAST OPPORTUNITY TO BACKUP DATA, ALL EXISTING DATA, CONTACTS, MESSAGES SETTINGS, APPS, ETC, WILL BE DELETED AFTER THE NEXT STEP.
MAKE SURE THE BATTERY INDICATOR IN THE NOTIFICATION AREA SHOWS GREEN, NOT ORANGE OR RED, BEFORE CONTINUING.
Flash RUU (rom.zip)
1. EITHER:
1a. Shut down your phone, then take out your battery and put it back in.
OR:
1b. Make sure fastboot is disabled in settings and shut down your phone (This can be done via Settings > Power> Untick "FAST BOOT" at the bottom.)
2. Keep hold of the volume down button and switch your phone on.
3. When it asks "Do you want to start the update", press Volume Up to accept (this can take a while and its normal for the system part to appear to go in a loop several times)
5. Press Power Off to reboot to first time setup.
6. Your phone is now debranded!
7. Remove PG58IMG.zip from your memory card
Source - forum.xda-developers.com/showthread.php?t=1193033
The only issue I have now is I can do find or dl the
http://81.89.105.12/~bin4ry/hboot/PG58IMG.zip file
Where can I get this or could you send me a link
majordj said:
I've looked every I'm running insert coin ics rom for the HTC sensation. The charger and the usb data slot is snapped i can charge but cant flash from the comp. Or read data from the phone.
I need to unroot from the microsd card back to stock ics in uk orange is this poss?? As i need my warranty back please help
I've found this post -
METHOD 2 - ENG HBOOT
Now the method I found to debrand (rather than messing about with CIDs), is using an ENG HBOOT, this is only temporary as the ROM we flash later on overwrites it.
Grab the file below (thanks to Bin4ry), and put it in the root of your SD Card. (i.e. if your on Windows, X:/ [where X is the letter of your Sensation's SD Card])
Quoteriginally Posted by Bin4ry
ENG Hboot:
[thanks Rahan95 for dumping ]
http://81.89.105.12/~bin4ry/hboot/PG58IMG.zip
Flash ENG HBOOT
1. EITHER:
1a. Shut down your phone, then take out your battery and put it back in.
OR:
1b. Make sure fastboot is disabled in settings and shut down your phone (This can be done via Settings > Power> Untick "FAST BOOT" at the bottom.)
2. Keep hold of the volume down button and switch your phone on.
3. When it asks "Do you want to start the update", press Volume Up to accept
5. Press Power Off to reboot back to normal homescreen
6. Remove PG58IMG.zip from your memory card
Download an RUU
1. You now need to pick the RUU you wish to flash, a good source is this thread:
http://forum.xda-developers.com/show....php?t=1074559
To debrand my Vodafone Sensation, I chose "RUU_Pyramid_HTC_Europe_1.35.401.1_Radio_10.43a.90 0 7.00U_10.51.9007.27_M3_release_198179_signed"
2. Once you have downloaded the RUU you would like to flash, run it (it can take a while to load), and stop when you get the welcome screen, which has a picture of a Sensation on the left and a red caution notice on the right.
3. Move this window out of the way (it forces itself into foreground), then open up windows explorer and go to:
C:\Users\[username]\AppData\Local\Temp
4. Then sort by Date Modified. Find the newest folder with a long random sequence of numbers as its name, go in here and you should see, three files and a folder: corecomp, dotnetinstaller, IBSEW64. (the files may be different on 32-bit OS), now go into the folder which has another long random name.
In there amongst a lot of files (use search if you need to), you will find rom.zip. This is the rom we want to flash!
5. Copy the rom.zip file to the root of your SD Card
(i.e. if your on Windows, X:/ [where X is the letter of your Sensation's SD Card])
6. Rename the rom.zip you just put on your SD Card, to PG58IMG.zip (ensure you do not rename it to PG58IMG.zip.zip or it wont work!)
7. Find the "HTC Android ROM Update Utility" Window, and hit Cancel.
THIS IS YOUR LAST OPPORTUNITY TO BACKUP DATA, ALL EXISTING DATA, CONTACTS, MESSAGES SETTINGS, APPS, ETC, WILL BE DELETED AFTER THE NEXT STEP.
MAKE SURE THE BATTERY INDICATOR IN THE NOTIFICATION AREA SHOWS GREEN, NOT ORANGE OR RED, BEFORE CONTINUING.
Flash RUU (rom.zip)
1. EITHER:
1a. Shut down your phone, then take out your battery and put it back in.
OR:
1b. Make sure fastboot is disabled in settings and shut down your phone (This can be done via Settings > Power> Untick "FAST BOOT" at the bottom.)
2. Keep hold of the volume down button and switch your phone on.
3. When it asks "Do you want to start the update", press Volume Up to accept (this can take a while and its normal for the system part to appear to go in a loop several times)
5. Press Power Off to reboot to first time setup.
6. Your phone is now debranded!
7. Remove PG58IMG.zip from your memory card
Source - forum.xda-developers.com/showthread.php?t=1193033
The only issue I have now is I can do find or dl the
http://81.89.105.12/~bin4ry/hboot/PG58IMG.zip file
Where can I get this or could you send me a link
Click to expand...
Click to collapse
The only solution I know to revert to stock is in step 5 THIS guide , but it requires a connection with the PC. The guide you find isn't for your problem, if I understand well. Have a read here also to understand why you can't revert to stock without PC connection. sorry I can't help more
P.S If you want to turn it back for repairs don't worry too much, they usually never check if you are rooted. Just install a custom ROM that looks like stock and change your boot image to the Orange one
Well that's the best idea I think what rom ics looks the most like stock.
majordj said:
Well that's the best idea I think what rom ics looks the most like stock.
Click to expand...
Click to collapse
There is a thread with stock 3.33 based ROM in the dev section, just search for it
Get here a stock 3.33 ROM
You'll be unrooted, just flash this ROM from recovery.
Now I don't know about your mobile company if it has a boot logo or smth.
Make sure you are SuperCID

Categories

Resources