Database Info

How Upgrade ?

In ftp site are three ROM posted :
750v:34 MB
TREOCINGULAR: 16,4MB
treo750vrompartial_bcaslis.zip:34 MB
Now i have a Vodafone Rom in italian languadge , the ROM posted are in english?
what are the difference trough the posted ROM'S ?
How can update my Treo ?
Kindest regards
Uccio

Try checking the treo wiki and read through everything before trying to perform the rom upgrade. Remember that a simple mistake can and might render your device useless.

How to!
zerimar said:
Try checking the treo wiki and read through everything before trying to perform the rom upgrade. Remember that a simple mistake can and might render your device useless.
Click to expand...
Click to collapse
"Insert the reader w/card into your USB, after the PC recognizes the card right click on the drive letter. Select Format from the options and make sure FAT32 is selected as the file system then select start.
Also, you need to copy the files to the memory card one at a time; DIAG file first and then delete the DIAG prior to loading the IMG file second.
Step 1:
-Copy the ‘CheeDIAG.nbh’ file to the root directory of a miniSD card. Note: Windows Mobile recognizes updates only from FAT32 formatted cards.
-Insert the card into the device.
-Press and hold both the PTTApp Button (lowest button on left side of device) + Pin Reset (next to miniSD card slot). You will be prompted to press the ‘End’ (red power) key to start the update. This step takes only a few seconds to complete. Once the flash is done, you will see: ‘Model ID: Palm Treo 750’ displayed by the device.
Step 2:
-Copy the ‘CHEEIMG.nbh’ file to the root directory of a miniSD card. Note: Windows Mobile recognizes updates only from FAT32 formatted cards.
-Insert the card into the device.
-Press and hold both the PTTApp Button (lowest button on left side of device) + Pin Reset (next to miniSD card slot). You will be prompted to press the ‘End’ (red power) key to start the update. This step takes about 5 minutes to complete.
-Hard reset the device once the device indicates the upgrade has been completed. To hard-reset, hold the ‘End’ (red power) key while pressing the pin reset button. Answer “yes” to “Erase all data” prompt.
Step 3:
Verify the device software via the device <start><settings><system tab><about><phone tab> The device should display firmware version on the resulting screen."
Good luck!

excuse me for asking,but there`s no file called ‘CheeDIAG.nbh’ or `CHEEIMG.nbh’ in files that are in the /Cheetah/Dumped_ROMs/ folder!
750v:34 MB consists of 3 .RAW files(What to do with them?)
treo750vrompartial_bcaslis with .RAW files inside,also
Treo750v_Dump_Cingular_ROM.zip with .dll`s mostly
Did I understand something wrong....?
Any help
THX in advance!

Roms
There are NO installable roms on the FTP!
The usable one is in the possesion of forum members.
Palm and/or Cingular asked politely ;-)) to remove them.
So you have to wait untill the new rom will be released later this month

i didn`t have time till now to wiew all the posts about this phone,and only now I saw that still there aren`t ROMS available.
If anyone has a ROM or a link for it,pls PM me!
THX in advance!

Kaiser Not Working

Hi Im Using Xp Pro
THIS IS WHERE IM UP TO .SORRY IM NOT USED TO FORUMS.NEWBY.[please scroll to bottom of page]
The exe has created a folder on your C drive called Unlocker. There are 2 folders inside that one called kaiser-HardSPLv1 and one called kaiser-simunlocker
Note for Vista users
===============
If you do not have the latest version of Mobile Centre follow This guide to explain how to change your drivers to the xp. You will have problems running the unlocker otherwise. Log in as administrator if you run the ROM update tool and unlocker. That also applies to XP users.
Instructions
============
1. Install HardSPL as per the instructions:
1- Connect Kaiser to computer using USB cable
2- Make sure ActiveSync icon is GREEN
3- RUN kaiser-hardSPL.exe on Computer (PC)
4- Follow instructions on screen
To check it has installed correctly, power off and then press power on while keeping camera pressed, this will enter the so called bootloader mode and you see a tri-colour screen (Red, Green, Blue). You should see "SPL-1.0 OliPof" on the second line in the top left corner. You can exit this mode by means of a "soft reset": press the reset button with the stylus.
2. Make a note of the radio version that is currently installed. You see the version strings in the splash screen which appears soon after power on (e.g. "R 1.27.14.09") (Or by going to Start, Settings, System, device information). Since we will flash a special radio in step 5 you need to flash back your original radio in the last step. (If you have a UK Orange Tytn II with the radio version 1.27.12.29, Use Radio version 1.27.12.32. Keep a note of the unlocking Code as you will need to enter it again after you have re-flashed the Radio.) (You will find download links at the bottom of the instructions)
3. Connect PC and Kaiser with a USB cable and keep it connected until the last step.
4. Power on the Kaiser and let it boot into Windows Mobile. On the PC make sure the activesync icon is green
5. After you unpacked the download you see directories "step1" and "step2". Go into "step1" and run KaiserCustomRUU.exe. This will flash the special patched radio rom. Follow the instructions until it is finished.
6. Power off your Kaiser and insert a different SIM, i.e. a SIM from another provider than the one your phone is locked to. (if you have a pin on the sim disable it first)
7. Once Windows Mobile has booted up it will (usually after you have entered the usual 4-digit PIN) show a window called "Simlock" and a textbox where you can enter a 8-digit unlock code. Now perform a soft reset by pressing the reset button *but* at the same time keep the camera button pressed. If you did it well you will be back in bootloader mode and you see the tri-color screen. The best technique is to press and hold the camera button first and then shortly press the reset button with the stylus.
8a. right-click activesync icon and uncheck "Allow USB connections" from Connection Settings
8b. On your PC, go into the "step2" directory and run "kaiser-simunlocker.exe". If all went well you will see the unlock code on your monitor and your Kaiser is being restarted
MY KAISER DOES NOT RESTART and stays in tri mode AND THERE IS NO PASSWORD ON SCREEN.THANKS AGAIN

mattdehat said:
HI,ive been installing sim unlock on my tmobile kaiser and at a certain point i get a problem,after tri-screen after soft reset with camera button pressed,on screen i get this
===kaiser sim unlocker[c}2008 by jockeyw2001
===donations happily accepted. paypal to [email protected]
WITHOUT THE PASSWORD.CANT UNDERSTAND IS SHOULD HAVE A PASSWORD AND AS EVER NOT HAPPENING FOR ME
ANY HELP WOULD BE APPRECIATED.THANKS
Click to expand...
Click to collapse
are you using vista? could you be a bit clearer on things? less caps?

Hi Im Using Xp Pro
THIS IS WHERE IM UP TO .SORRY IM NOT USED TO FORUMS.NEWBY.
The exe has created a folder on your C drive called Unlocker. There are 2 folders inside that one called kaiser-HardSPLv1 and one called kaiser-simunlocker
Note for Vista users
===============
If you do not have the latest version of Mobile Centre follow This guide to explain how to change your drivers to the xp. You will have problems running the unlocker otherwise. Log in as administrator if you run the ROM update tool and unlocker. That also applies to XP users.
Instructions
============
1. Install HardSPL as per the instructions:
1- Connect Kaiser to computer using USB cable
2- Make sure ActiveSync icon is GREEN
3- RUN kaiser-hardSPL.exe on Computer (PC)
4- Follow instructions on screen
To check it has installed correctly, power off and then press power on while keeping camera pressed, this will enter the so called bootloader mode and you see a tri-colour screen (Red, Green, Blue). You should see "SPL-1.0 OliPof" on the second line in the top left corner. You can exit this mode by means of a "soft reset": press the reset button with the stylus.
2. Make a note of the radio version that is currently installed. You see the version strings in the splash screen which appears soon after power on (e.g. "R 1.27.14.09") (Or by going to Start, Settings, System, device information). Since we will flash a special radio in step 5 you need to flash back your original radio in the last step. (If you have a UK Orange Tytn II with the radio version 1.27.12.29, Use Radio version 1.27.12.32. Keep a note of the unlocking Code as you will need to enter it again after you have re-flashed the Radio.) (You will find download links at the bottom of the instructions)
3. Connect PC and Kaiser with a USB cable and keep it connected until the last step.
4. Power on the Kaiser and let it boot into Windows Mobile. On the PC make sure the activesync icon is green
5. After you unpacked the download you see directories "step1" and "step2". Go into "step1" and run KaiserCustomRUU.exe. This will flash the special patched radio rom. Follow the instructions until it is finished.
6. Power off your Kaiser and insert a different SIM, i.e. a SIM from another provider than the one your phone is locked to. (if you have a pin on the sim disable it first)
7. Once Windows Mobile has booted up it will (usually after you have entered the usual 4-digit PIN) show a window called "Simlock" and a textbox where you can enter a 8-digit unlock code. Now perform a soft reset by pressing the reset button *but* at the same time keep the camera button pressed. If you did it well you will be back in bootloader mode and you see the tri-color screen. The best technique is to press and hold the camera button first and then shortly press the reset button with the stylus.
8a. right-click activesync icon and uncheck "Allow USB connections" from Connection Settings
8b. On your PC, go into the "step2" directory and run "kaiser-simunlocker.exe". If all went well you will see the unlock code on your monitor and your Kaiser is being restarted
MY KAISER DOES NOT RESTART AND THERE IS NO PASSWORD ON SCREEN.THANKS AGAIN

so what step did you get up to?? you didnt really need to paste the whole instructions as most of already know the steps.

hi.istarted fresh.phone now unlocked.many thanks to all.I LOVE THIS SITE...MOST INFORMATIVE.MANY THANKS AGAIN

I got stucked into a Multi dotted colored screen with my Kaiser8925, and I can´t flash the old radio versión, I got the file, but I try to flash my kaiser, and it gets not installed, I think the new radio version I flashed is causing the problems. ¿Can you help me?

josereja said:
I got stucked into a Multi dotted colored screen with my Kaiser8925, and I can´t flash the old radio versión, I got the file, but I try to flash my kaiser, and it gets not installed, I think the new radio version I flashed is causing the problems. ¿Can you help me?
Click to expand...
Click to collapse
Thread hi-jacking is not very good...also posting the same thing in multiple threads isn't either...But, try reinstalling your Windows rom...Sounds like thats the issue. Could be something more severe though.

Flashed or Not

Hi it seems like I need to do a new thread for this, I just need answers thank you
*upon checking my phone
I have this
ROM Version: 3.29.707.0 WWE
ROM Date: 05/07/08
Radio Version: 1.65.16.25
Protocol Version: 25.83.20.02H
and as I learn to check what Hard SPL is installed in my device (thanks to you guys ) it says 3.29. 0000 or something like that, so my question is... does my phone already have been flashed? if so can i skip to to loading the Rom i wanted, i do need help thanks
if not this is from mskip
1. MAKE SURE YOUR KAISER HAS AT LEAST 50% BATTERY POWER FIRST
2. Download and Unzip *THIS* File
3. Flash HardSPL 3.29 [ESSENTIAL]
Flashing via ActiveSync with USB Lead
1. Copy JumpSPL1.56-KAIS.exe, JumpSPL1.93-KAIS.exe and JumpSPL1.94-KAIS.exe to your device memory (NOT STORAGE CARD)
2. Pull out the battery and reinsert it (this step IS important) *DONT turn phone back on yet*
3. REMOVE SIM and SD CARDS!!
4. Turn phone back on and let it boot back into your operating system
5. Connect your phone to PC with a USB cable and wait until it syncs with your PC
6. Run File Explorer on your phone, browse to where you copied JumpSPL1.56-KAIS.exe on your device and run it (make sure the USB cable is still connected). If you get a white screen then reset your device and now try JumpSPL1.93 and lastly try JumpSPL1.94 if that one doesnt work.
7. CLick Continue on phone when prompted
8. After a few seconds the tri colour screen will appear on the phone and "USB" will be displayed at the bottom
9. Unplug the usb cable for 30 seconds and then Replug (phone will not re-sync but still says "USB" on the screen)
10. Right click on the Activesync icon in the bottom corner icon on the computer, goto connection settings, deselect "Allow USB connections" and click "ok"
11. Run the KaiserCustomRUU.exe file on your PC thats in the same folder as the HardSPL .nbh file and follow instructions (ticking boxes and clicking Next) *DO NOT re-enable USB Connections in Activesync*
12. Update will goto 100% (should take less than a minute), the Congratulations screen will be displayed on the PC and the phone will restart
13. Unplug USB cable from phone then REPLACE SIM and SD CARDS !!
14. Restart phone
*Remember to re-enable "Allow USB connections" in Activesync connection settings after a successful flash*
Flashing via MicroSD Card using cmonex HardSPL 3.29 [OPTIONAL]
FOR UPGRADING HARDSPL ONLY!! THIS WONT WORK UNLESS YOU ALREADY HAVE HARDSPL ON YOUR PHONE
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download Cmonex's HardSPL 3.29SD, unzip it and copy the 2 files into the root of your MicroSD Card
(KAISDIAG.NBH is basically an SSPL patched to load from SD without booting OS)
(KAISIMG.NBH is cmonex HardSPL 3.29)
3. Insert the microSD Card into the phone
4. Hold in the Power and Camera buttons, then press the reset button with the stylus for about 3 seconds until the BootLoader screen appears
5. It should say Loading / Update in progress and then to a screen saying SPL 1.00.OliNex
6. It should now say Press Power Button to flash or just flash the KAISIMG.NBH and then reset
7. At this point it should boot to the OS, if it doesn't then flash an OS (delete the previous KAISDIAG.NBH and KAISIMG.NBH from the SD Card and use Flashing Rom from MicroSD Card method)
8. After the Operating System loads, DELETE the KAISDIAG.NBH and KAISIMG.NBH files
*To check HardSPL version on your phone Enter Bootloader by Holding in the Power and Camera buttons, press the reset button with the stylus for 3 seconds until the tri-colour screen appears, then read the 2nd line which is the SPL version*
4. SIM and CID-Unlock [OPTIONAL]
For more reading go *HERE*
* YOUR DEVICE MUST BE SYNCHED WITH YOUR COMPUTER BEFORE RUNNING EACH STEP *
*Put your phone into Bootloader and update to a 6.1 Rom first if you get a black screen after Flashing the Patched Radio*
*If the program wont run u may need to install Microsoft .NET 2.0 on your computer to get it working*
1. Make a note of your current Radio in case you need to flash it back
2. Run KaiserUnlocker.exe, follow the instructions
(if you already have HardSPL on your phone you can skip straight to Step2)
3. After patched Radio has been flashed phone will restart and sync with the computer
4. On the Unlocker Program it should say Radio Patched at the bottom
5. Click on Step3 (Run Unlocker). This will bring up the Unlocker screen on your phone
6. If you want to check the status of your Sim Lock or CID Lock click the appropriate buttons
7. Click on Remove Sim Lock and Set CID, then click "Commit Changes"
* IF YOU DONT NEED TO FLASH A NEW ROM THEN PROCEED TO STEP6 TO PUT YOUR DESIRED RADIO BACK*
Click to expand...
Click to collapse
are the instructions from flashing hard spl 3.29 below it or what? I'm just confused coz' I found this tutorial here in the forums also http://forum.xda-developers.com/showpost.php?p=2498297&postcount=10
Im just confused thanks

If you are confused, stop.
Re-read again and again, until it makes sense. Understanding the huge material around here is not to be taken in only one day.
I spent my early days 2 weeks by merely reading, collecting tools (and patches) before even attempting to flash.

I just needed an answer if my phone's already flashed that's it if it is flashed could i skip now on flashing my desired rom? that's just it, just answers from experts. I'm reading btw.

any help will do

On bootloader will say Hard if have hard-spl.
You could have asked in teh thread rather than starting new so as to keep forum clean.
On that note thread closed.

How to install Android on my Sd for My HTC HD2

To anyone of knowledge I have a HTC HD2 I have been trying to install Android from on here from many diiferent links etc.. and everytime I installit to mycomputer then unzip and install on my SD i run the Clcrd then Haret then my phone either shows a penguine or htc logo I let it sit for over 2 to 4 hurs everytime i try to install it on my phone and it just sits there. is it something Im not doing are there steps Im missing or things I need to installl along with the android program i choose I am super frusrtated can someone please help me get android up and running .. Thanks

mallfox said:
To anyone of knowledge I have a HTC HD2 I have been trying to install Android from on here from many diiferent links etc.. and everytime I installit to mycomputer then unzip and install on my SD i run the Clcrd then Haret then my phone either shows a penguine or htc logo I let it sit for over 2 to 4 hurs everytime i try to install it on my phone and it just sits there. is it something Im not doing are there steps Im missing or things I need to installl along with the android program i choose I am super frusrtated can someone please help me get android up and running .. Thanks
Click to expand...
Click to collapse
First of all tell me about your hd2, what rom is it currently running (stock 2.08, 3.14?) , what radio do you have? Whats your sd card?
All these questions are relevant to make droid work.

I'm not sure if this will work or not. But I had a similar problem when I first rooted my HD2. Under the Android folder, there is a text file: startup.txt
Open it up. The last line I've found typically reads "boot". Now, I don't know if this affects everyone. But after reading for 18+ hours when I first rooted my phone, I remembered reading somewhere that that particular line should read "bootlinux". And I've found that no matter what build I use, if I don't change it to bootlinux, it wouldn't get past the HTC. So try adding "linux" after the "boot". Then try starting it up again with CLRCAD.exe then haret.exe.
Hope that works for you.

RAM 576... OS version 5.2.2191 (21913.5.0.94) ... manilla version 2.5.20181424.0 ...Rom version 3.14.53.1(04666) WWE ... Radion version 2.15.50.14 ... SD card is Fat32.. i have tried alot of programs and have yet to get it to work . and i thank you both for your input I dont know what else to do...

mallfox said:
RAM 576... OS version 5.2.2191 (21913.5.0.94) ... manilla version 2.5.20181424.0 ...Rom version 3.14.53.1(04666) WWE ... Radion version 2.15.50.14 ... SD card is Fat32.. i have tried alot of programs and have yet to get it to work . and i thank you both for your input I dont know what else to do...
Click to expand...
Click to collapse
Did you erase all other content from your sd card, and was the content put in a named folder called Android?

GUIDE (yes another one) for ANDROID on HD2
mallfox said:
RAM 576... OS version 5.2.2191 (21913.5.0.94) ... manilla version 2.5.20181424.0 ...Rom version 3.14.53.1(04666) WWE ... Radion version 2.15.50.14 ... SD card is Fat32.. i have tried alot of programs and have yet to get it to work . and i thank you both for your input I dont know what else to do...
Click to expand...
Click to collapse
Here hope this helps! any questions feel free to ask...
I just posted this in another thread to clear some things up for some guys ...... hope this clears up the process for you a bit
............................excerpted from previous post........................................
********BTW i have attached a little template that i use when flashing various roms and storing them on my PC. has task29, HSPL & MAGLDR already in it. all u need to do is go to the xda hd2 master radio thread to grab your appropriate radio and put that into the empty radio file. then find the rom you want to test out and usually the developer will have both rom (obviously) and the appropriate CWM that u should use with it and just put those in their respective empty folders i have in the attached file. that way all the steps below will line up to the files i have attached
OH YEAH, FORGOT... THESE STEPS ARE TO BE DONE AFTER THE INITIAL PREREQUISITES i.e. windows mobile device center, activesync, proper spl version...blah blah blah
--------the following steps 1 - 4 are to be preformed while at the tri-color boot screen (easiest way to reach is to turn off your phone while its connected to your PC then immediately hold volume down button till you see it n wait for it to say usb in the white section).
(by the way your device will ALWAYS automatically restart itself after a couple seconds if it is shut down while plugged in via USB to either a wall/car charger or hooked up to a PC this is normal and a small hiccup either due to the use of magldr or the hspl but dont worry)...cant quite remember
1. run task 29
-double click the only icon in file if your using the one provided by doloop
-wait for it to run and do its thing. when its finished it will automatically turn off your device so be sure to hold down the volume key as soon as it does.
2. install radio
-run the "customRUU" file with the HD2 icon in the radio of your choosing
-it will operate in a similar fashion as the task 29, automatically turning off device upon completion.... down on the vol key
3. install hspl3/hspl4
-run the "HSPL3_PKG/HSPL4_PKG" file. should be the only one in there
-make sure you select 2.08.HSPL in the setup and it will execute itself just like the installers in the previous two steps n turn off your phone... down vol key
4. install magldr113
-make sure your selecting "rom update utility" in the magldr113 file. dont run the "DAF" it wont work properly if you do and youll get errors
-BUT THIS TIME AS IT TURNS ITSELF OFF HOLD DOWN THE POWER BUTTON ON YOUR DEVICE AS IT BOOTS UP UNTIL U GET TO MAGLDR AND CONTINUE TO HOLD IT DOWN UNTIL YOU SEE ABOUT 12 DIFFERENT OPTIONS...
5. install CWM recovery
-go to option 5 "USB Flasher" and hit the green call key. wait a few moments till it shows USB....USB make sure the second usb pops up and your PC recognizes the connection. then when it does sync you get to......
-while still in the usb flasher mode above, simply run you desired CWM recovery which should the one your developer recommends for the builds as the requirements tend to vary from rom to rom.
-this is achieved by selecting the "DAF" file from the clockworkmod recovery your using
-and again this installer will shut off your device upon completion and HOLD DOWN THE POWER KEY LIKE ABOVE TILL YOUR BACK AT THE MAGLDR MAIN MENU (with options 1-12).
6. install rom
-now go to option 8 "AD Recovery" and hit the green call button to enter into the CWM recovery u just installed
-after it loads up (GO!GO!GO!) go down to the "mounts and storage" option that is third from the bottom and hit the call key.
-once there go to the last option "mount USB storage" and hit the call key.
-give your PC a few moments to recognize the sd card for your device and choose to open it when your PC prompts with the regular file explorer or just find it and double click on the newly recognized drive (sdcard) if your PC doesnt auto prompt you.
-now the new drive (sdcard) should be empty (depending...) then just find the desired rom you chose to use, right click on it and copy.....then over to the new drive (sdcard) and paste. might take a min or two depending on the roms size
-once the copying is complete hit the call button to "unmount" your sdcard then the back button on your device till your back at the CWM main screen
-now go to the fifth option down and "install zip from sdcard" and hit the call button
-now select the second option "choose zip from sdcard" and select the zip file you just copied to your sdcard. then it will begin to install the rom and all rom install times vary by build. some take a minute, some seem like they take forever.
-once installation is complete hit the back button till your back at CWM main screen and choose the last option which is to "power off"
-then tap the power button(if u unplugged it from usb otherwise it wil reboot by itself) to turn on your device and give it some time for the initial boot and load as it has to set up everything u just installed. subsequent boot wont take as long but again it can all vary from rom to rom.
-after initial load and a successful bootup you should arrive at ether the lockscreen or a startup screen. give the rom a few more mins to settle and dont hit any buttons. then unlock the device or skip through the startup options and get to the home screen. maybe give it another min to settle the launcher and the last bit of data and resist the urge to mess with the features. your gonna hate this but hold down the power button and select power off device from the popup menu. i know it sucks but it is best practice when flashing roms. after device shuts off wait a few seconds and turn it back on and let it reboot. should be faster this time and when u get to your lockscreen simply give it a few seconds to settle again, unlock and go to main launcher a wait a couple more seconds for it to finish settling and.....have fun! (every time i restart my device for any reason i will always give it a few moments to finish loading up before just blazing away with the apps)
WOW! maybe its not so abridged after all, but oh well tried my best to be as clear as possible so people can utilize their HD2 to its fullest potential.
HOPE THIS HELPS AND IF INDEED I HAVE PLEASE HIT THE THANKS BUTTON

MEG4LOM4NI4C said:
Here hope this helps! any questions feel free to ask...
I just posted this in another thread to clear some things up for some guys ...... hope this clears up the process for you a bit
............................excerpted from previous post........................................
********BTW i have attached a little template that i use when flashing various roms and storing them on my PC. has task29, HSPL & MAGLDR already in it. all u need to do is go to the xda hd2 master radio thread to grab your appropriate radio and put that into the empty radio file. then find the rom you want to test out and usually the developer will have both rom (obviously) and the appropriate CWM that u should use with it and just put those in their respective empty folders i have in the attached file. that way all the steps below will line up to the files i have attached
OH YEAH, FORGOT... THESE STEPS ARE TO BE DONE AFTER THE INITIAL PREREQUISITES i.e. windows mobile device center, activesync, proper spl version...blah blah blah
--------the following steps 1 - 4 are to be preformed while at the tri-color boot screen (easiest way to reach is to turn off your phone while its connected to your PC then immediately hold volume down button till you see it n wait for it to say usb in the white section).
(by the way your device will ALWAYS automatically restart itself after a couple seconds if it is shut down while plugged in via USB to either a wall/car charger or hooked up to a PC this is normal and a small hiccup either due to the use of magldr or the hspl but dont worry)...cant quite remember
1. run task 29
-double click the only icon in file if your using the one provided by doloop
-wait for it to run and do its thing. when its finished it will automatically turn off your device so be sure to hold down the volume key as soon as it does.
2. install radio
-run the "customRUU" file with the HD2 icon in the radio of your choosing
-it will operate in a similar fashion as the task 29, automatically turning off device upon completion.... down on the vol key
3. install hspl3/hspl4
-run the "HSPL3_PKG/HSPL4_PKG" file. should be the only one in there
-make sure you select 2.08.HSPL in the setup and it will execute itself just like the installers in the previous two steps n turn off your phone... down vol key
4. install magldr113
-make sure your selecting "rom update utility" in the magldr113 file. dont run the "DAF" it wont work properly if you do and youll get errors
-BUT THIS TIME AS IT TURNS ITSELF OFF HOLD DOWN THE POWER BUTTON ON YOUR DEVICE AS IT BOOTS UP UNTIL U GET TO MAGLDR AND CONTINUE TO HOLD IT DOWN UNTIL YOU SEE ABOUT 12 DIFFERENT OPTIONS...
5. install CWM recovery
-go to option 5 "USB Flasher" and hit the green call key. wait a few moments till it shows USB....USB make sure the second usb pops up and your PC recognizes the connection. then when it does sync you get to......
-while still in the usb flasher mode above, simply run you desired CWM recovery which should the one your developer recommends for the builds as the requirements tend to vary from rom to rom.
-this is achieved by selecting the "DAF" file from the clockworkmod recovery your using
-and again this installer will shut off your device upon completion and HOLD DOWN THE POWER KEY LIKE ABOVE TILL YOUR BACK AT THE MAGLDR MAIN MENU (with options 1-12).
6. install rom
-now go to option 8 "AD Recovery" and hit the green call button to enter into the CWM recovery u just installed
-after it loads up (GO!GO!GO!) go down to the "mounts and storage" option that is third from the bottom and hit the call key.
-once there go to the last option "mount USB storage" and hit the call key.
-give your PC a few moments to recognize the sd card for your device and choose to open it when your PC prompts with the regular file explorer or just find it and double click on the newly recognized drive (sdcard) if your PC doesnt auto prompt you.
-now the new drive (sdcard) should be empty (depending...) then just find the desired rom you chose to use, right click on it and copy.....then over to the new drive (sdcard) and paste. might take a min or two depending on the roms size
-once the copying is complete hit the call button to "unmount" your sdcard then the back button on your device till your back at the CWM main screen
-now go to the fifth option down and "install zip from sdcard" and hit the call button
-now select the second option "choose zip from sdcard" and select the zip file you just copied to your sdcard. then it will begin to install the rom and all rom install times vary by build. some take a minute, some seem like they take forever.
-once installation is complete hit the back button till your back at CWM main screen and choose the last option which is to "power off"
-then tap the power button(if u unplugged it from usb otherwise it wil reboot by itself) to turn on your device and give it some time for the initial boot and load as it has to set up everything u just installed. subsequent boot wont take as long but again it can all vary from rom to rom.
-after initial load and a successful bootup you should arrive at ether the lockscreen or a startup screen. give the rom a few more mins to settle and dont hit any buttons. then unlock the device or skip through the startup options and get to the home screen. maybe give it another min to settle the launcher and the last bit of data and resist the urge to mess with the features. your gonna hate this but hold down the power button and select power off device from the popup menu. i know it sucks but it is best practice when flashing roms. after device shuts off wait a few seconds and turn it back on and let it reboot. should be faster this time and when u get to your lockscreen simply give it a few seconds to settle again, unlock and go to main launcher a wait a couple more seconds for it to finish settling and.....have fun! (every time i restart my device for any reason i will always give it a few moments to finish loading up before just blazing away with the apps)
WOW! maybe its not so abridged after all, but oh well tried my best to be as clear as possible so people can utilize their HD2 to its fullest potential.
HOPE THIS HELPS AND IF INDEED I HAVE PLEASE HIT THE THANKS BUTTON
Click to expand...
Click to collapse
Thanks

help needed complete noob
Hi all...total noob in need of expert advice...i have a htc hd2..it had windows 6.5 so upping to android hopefully. the step I am getting stuck on is installing from memory card. radio is 2.5,magdlr 113, clockwork is installed and spl 2.08.hspl.
What I am getting is the following.
Installing: /sdcard/.android/update.zip
Finding update package...
Opening update package...
E:Can't open /sdcard/update.zip
(bad)
Installation aborted.
I have been trying for a week with no success.. Help.
Thanks in advance.

It could be a corrupted zip. Try downloading again, if you've not tried that.
Sent from my GT-I9100 using Tapatalk

Hi..Thanks for the reply. I have downloaded many firmwares and still no joy.Rather annoying really as its just the last step and really need to finish it off. Anyone having a android firmware I could download? Again thanks in advance.
Finally managed to put android 2.2 on, don't know how but it is on there...but no connection to the internet, it says on the setting for mobile network no connection.
If someone could list how exactly to put android on my hd2 in lamans terms (lol) I would really appreciate it..i.e. what to flash first and so on.

I dont know if you read the following guides but they are pretty awesome. Follow the first link in order to get 2.2 on. I know you said you did it but I would do it again since I dont like starting in between steps, rather do it start to finish. Follow the second link to put another ROM on.
http://forum.xda-developers.com/showthread.php?t=893948
http://forum.xda-developers.com/showthread.php?t=1044830

UK G1 (DRC92) - Just wanna install Froyo - VERY confused

Hiya!
So, I am no android beginner, but to me there seems to be a continual branching off & fragmentation (and obsolescence) in tutorials, howto's etc etc.
This is what I have: UK T-mobile G1, running Android 1.6, build DRC92
This is what I want: UK T-mobile G1, running Android 2.2 or higher
This is what irritates me: 1001 different tutorials, each of which (wrongly) *assume* you know what you are doing with this particular handset
I know what I am doing with ZTE, and Android OS in general, but I want to get this CLEAR, as clear as crystal, and I want to do it by following a SIMPLE, non-ambiguous, non-assuming tutorial. That SHOULD be simple, but it seems not.
I need to upgrade "SPL" and "RADIO". I need this explaining please, in as much detail as you can, if you don't mind?
I am sorry to sound demanding, but this whole process is a minefield of conflicting opinions, geek ego battles and preferences... and ALL I wanna do is upgrade!
Please, any help?
PLEASE: I ask that you don't just simply link me to other tutorials, as I am confused about how to do this, and that will just set me back to square one again. If you are able to spare a few minutes to explain what to do, I would be most grateful.
Thank you!

It is hard not to link you to the instruction that is already there. But I do understand your frustration. When I first started I had the same (similar problem) and end up following one of the instruction. FYI, the only links I posted is the recommended Froyo ROM. It has Android 2.2.1.
Simply put, here is from Instruction I have when I first rooted my G1:
Disclaimer:
WARNING: I am not responsible if you did something to brick your phone.
Disclaimer:
I FOUND THIS TO BE THE EASIEST METHOD OF ROOTING A G1 AND INSTALLING A STABLE BUILD OF FROYO.
THIS IS DESIGNED FOR THE COMPLETE BEGINNER!!
I HAVE THIS ON MY G1 WITH NO PROBLEMS AT ALL!!!
Rooting Your Stock T-Mobile G1 (HTC DREAM) AND INSTALLING A STABLE ANDROID 2.2 FROYO BUILD.
**Please make sure your phone is completely charged before doing this**
**I am not responsible for anything that happens to your phone. Do this at your own risk**
---------------------------------------------------------------------------------------------
I was pretty worried about bricking my phone, but it is almost impossible if you do this step by step and correctly. Just make sure to follow the steps!
---------------------------------------------------------------------------------------------
Prerequisites:
**ALL DATA/APPLICATIONS WILL BE REMOVED FROM YOUR PHONE AND IT WILL BE RETURNED TO FACTORY SETTINGS AFTER THE FOLLOWING STEPS. MAKE SURE YOU HAVE SYNC SET UP FOR YOUR DATA SO THAT YOU CAN RECOVER YOUR CONTACTS!** (TO SYNC GO TO SETTING > DATA SYNChronization > make sure AUTO SYNC is checked as well as contacts calendar and gmail)
Here is what you will need:
1) Your Phone
2) A Computer
3) USB Cable
Download the following file onto your computer: (DO NOT UNZIP OR CHANGE ANY FILES!)
ALL THE LINKS TO DOWNLOAD THE FILES ARE HERE: pktos.blogspot.com
Original DREAIMG.nbh (make sure you download the UK version)
Cupcake Update.zip
FlashRec.apk
Amon Ra’s Recovery Image
G1 Radio
G1 HardSPL
Generic G1 ROM w/ Root
GAPPS (if you wants it)
ALL THE LINKS TO DOWNLOAD THE FILES ARE HERE: pktos.blogspot.com
---Froyo ROM---
Recommended Froyo ROM: Froyo Melt with custom theme or DreamTem Froyo.
---Froyo ROM---
-------------------------------------------------------------------------------------------
I) Formatting the SD Card and Downgrading to RC29(YOU WILL DELETE EVERYTHING OFF YOUR SD CARD!)
1. Plug your USB cable into your computer and then plug your phone in.
2. Mount your SD card by sliding down the notification bar and selecting mount.
3. Go to My Computer and access your SD card.
4. BACKUP ANY FILES THAT YOU WANT ONTO YOUR COMPUTER. VERY IMPORTANT!
5. Go back to my computer and right click on the drive that is your sd card. Click format. Choose FAT32 from the drop down and hit the format button. This removes all data from your memory card.
6. Once the format is complete: drag and drop "DREAIMG.nbh & Update.zip files that you downloaded into the sd card. (DO NOT create a folder or anything, just put it right in the SD card)
7. Unmount your phone by going through the notification bar and then unplug your phone Turn your phone off. from your computer.
8. Press and hold the camera+end key until until you see a screen with colored bars, then let go. This is the bootloader. The screen will turn gray with blue writing on it.
9. Hit the end key to start the update. DON'T DO ANYTHING UNTIL THIS IS DONE!
10. Once it is finished it press the trackball to reboot. (If it goes back the the colored bar screen and doesn't reboot try holding the home+menu+end key, if this doesn't work, just remove the batter and put it back in and turn the phone on)
11. Once the phone is on, just turn it back off.
12. Now press the Home+End Key until you see a triangle with an exclamation point in it (this is recovery mode). Once you see this let go of the buttons.
13. Open the keyboard and press ALT and L, and then Press ALT and S. Now wait until the phone reboots (it will do this automatically once the update is applied) (Don't worry if you see picture of a box and a g1 or a chip with an arrow)
14. Once the phone reboots, go ahead and and go through the welcome guide and get to the home screen.
II) Flashing a Recovery Image
1. Now with your phone at the home screen, go to settings>applications> an turn on unknown sources.
2. Now go to settings>SD card and Phone Storage>Unmount SD Card
3. Now Click format sd card and go ahead and format your sd card. It will automatically remount after.
4. Go back to the home screen and plug and mount the phone to the computer again as you did earlier.
5. Place the following files you downloaded earlier right into the sd card: FlashRec.apk, and Amon Ra's Recovery Image (Again not in any folder or anything, just on the sd card)
6. Once they are transferred go ahead and unmount and unplug your phone from the computer
7. Go and download a file manager from the android market (I suggest LINDA FILE MANAGER)
8. Once downloaded, open the file manager and go to SD card, and click the FlashRec.apk file and then click install. If it asks -> Tell it to use package installer to open it (it probably wont ask but if it does)
9. Once installed click open (it will be on bottom left of screen)
10. Then click the button that says "backup recovery image"
11. Once it says "backup complete" open the keyboard and type the following: /sdcard/recovery.img
12. The click "flash custom recover image" and wit until it says "Flash complete"
13. Go back to the home screen and then turn off the phone.
14. Turn the phone back on into recovery mode by holding down the home and power buttons. You will see a bunch of text on top of a black background with an HTC logo in the middle.
III) Partitioning and Loading the latest radio
1. Scroll down to "Partition SD Card"
2. Click "Partition SD"
3. Press the Home key to confirm
4. Use the trackball to increase the "swap size" to 96MB then press Home key
5. Make sure "EXT2" is set to 512 MB then Click the Home Key
6. Make sure "Fat32 size" is set to remainder and then press the Home Key and then the phone will begin partitioning.
7. Once partitioning is complete scroll down and select to "SD: ext2 to ext3" and then press the Home key. Wait for it to upgrade.
8. Once the Upgrade is complete hit the "back" button to get back to the main menu. Then scroll down and select "USB-MS Toggle" and wait for it to enable.
9. Now plug the phone into the computer again. Now transfer the files downloaded earlier: G1 Radio, G1 HardSPL, Generic G1 Rom w/ root, to the phone. (AGAIN KEEP THE FILES JUST IN THE SD CARD AND NOT IN A FOLDER OR SOMETHING)
10. Once the transfer is complete hit the Home key to disable the USB-MS toggle and return back to the main menu of recovery mode. Unplug your phone.
11. Scroll down and select "Flash .zip from SDcard"
12. Select the G1 Radio file (named OTA Radio or something like that) and hit the Home key to confirm. DO NOT SELECT ANY OTHER FILE, THE RADIO MUST BE DONE FIRST.
13. Once the Radio Flash is complete Press Home+Back to reboot the phone. It will then say "writing radio image" and then reboot back into recover mode (this will take some time)
14. Once back into recovery mode, scroll and select "Flash zip from SDcard" again.
15. This time choose the SPL file (named somthing like "Latest G1 SPL.zip") and then click the HOME KEY to confirm.
16. Once it finishes, hit HOME+Back to reboot once again. It will say "writing boot image" and then reboot
back to recovery mode.
17. Once again scroll to "Flash zip from SDCard" and choose the Generic G1 Rom file (Named something like Generic G1 Root Rom.zip) and click Home to confirm and wait for it to finish.
18. Once finished it should go back to the main menu and say"Install from SD card complete"
19. Now click on the "Reboot System Now" choice. (Home+Back)
20. Wait for the phone to reboot back into Android.
IV)Installing ROM (Android 2.2.x Froyo for HTC DREAM)
1. Once back into Android, turn the phone back off.
2. Hold the Home+Back keys to turn the phone on and get it back into recovery mode
3. Select "USB-MS Toggle" and wait for it to enable
4. Once enabled, plug your phone in and transfer the CYANOGENMOD6 and GAPPS file ito your SD card/phone. (again not in any folder, just in the sd card)
5. Once the files are transferred, press the Home key to disable USB-MS Toggle and return to the main menu, and then unplug your phone.
6. Scroll down and select "wipe" and then select "wipe data / factory reset" and then hit the Home key to confirm. Wait for it to finish the wipe. It will say "Data wipe complete"
7. Hit the back key to return to the main menu.
8. Scroll and select "Flash Zip from SDCard"
9. Select the ROM Named that you have downloaded and hit Home to confirm and wait for it to finish.
10. Once finished it will go back to the main menu and say "Install from SD Card Complete"
11. Go back to "Flash Zip from SDCard"
12. Select the Gapps File Named something like "gapps-mdpi-FRF91-3-signed.zip" and click home to confirm.
13. Once it is finished you should be back at the main menu. Select "Reboot System Now" and wait for the phone to reboot.
14. The reboot will take some time, (roughly 5-10 minutes) so don't freak out. Just put your phone down and go do something =)
CONGRATS! YOU have successfully rooted your G1 and installed ANDROID 2.2.x Froyo
Click to expand...
Click to collapse

BeenAndroidized said:
It is hard not to link you to the instruction that is already there. But I do understand your frustration. When I first started I had the same (similar problem) and end up following one of the instruction. FYI, the only links I posted is the recommended Froyo ROM. It has Android 2.2.1.
Simply put, here is from Instruction I have when I first rooted my G1:
Disclaimer:
WARNING: I am not responsible if you did something to brick your phone.
Disclaimer:
Click to expand...
Click to collapse
My build is DRC92, and from what I gather, I need a "gold card" (impossible to find somewhere to generate the image!)
I give up.

Have you try this software to create Goldcard?
http://forum.xda-developers.com/showpost.php?p=11655667&postcount=1

BeenAndroidized said:
Have you try this software to create Goldcard?
http://forum.xda-developers.com/showpost.php?p=11655667&postcount=1
Click to expand...
Click to collapse
Okay. I finally got revskills site to send me a goldcard IMG. All updated, just putting FroSense 10 on now.... MAN. It takes AGES to boot first time! lol
Thank you for helping me! God bless you.

glossywhite said:
Okay. I finally got revskills site to send me a goldcard IMG. All updated, just putting FroSense 10 on now.... MAN. It takes AGES to boot first time! lol
Click to expand...
Click to collapse
Yes, it does take time for the first boot, especially FroSense. Glad you got it going though.
glossywhite said:
Thank you for helping me! God bless you.
Click to expand...
Click to collapse
Glad to be of services... And anytime...

glossywhite said:
Hiya!
So, I am no android beginner, but to me there seems to be a continual branching off & fragmentation (and obsolescence) in tutorials, howto's etc etc.
This is what I have: UK T-mobile G1, running Android 1.6, build DRC92
This is what I want: UK T-mobile G1, running Android 2.2 or higher
This is what irritates me: 1001 different tutorials, each of which (wrongly) *assume* you know what you are doing with this particular handset
I know what I am doing with ZTE, and Android OS in general, but I want to get this CLEAR, as clear as crystal, and I want to do it by following a SIMPLE, non-ambiguous, non-assuming tutorial. That SHOULD be simple, but it seems not.
I need to upgrade "SPL" and "RADIO". I need this explaining please, in as much detail as you can, if you don't mind?
I am sorry to sound demanding, but this whole process is a minefield of conflicting opinions, geek ego battles and preferences... and ALL I wanna do is upgrade!
Please, any help?
PLEASE: I ask that you don't just simply link me to other tutorials, as I am confused about how to do this, and that will just set me back to square one again. If you are able to spare a few minutes to explain what to do, I would be most grateful.
Thank you!
Click to expand...
Click to collapse
Well first of all this isn't Q&A this is a development section, second look for the guide in the dev section, its easy to follow and not complicated at all, download a few files, blah blah blah your done. Took me 5 minutes.
Sent from my T-Mobile G1 using XDA App

i won`t go down to rc29. on market is an application named universal androot which works on htc dream ( 1.5 and higher ). this will root your phone but until you`ll restart the phone, you`ll have to flash recovery image ( amon-ra-1.7.0 ). after you restart your phone and still have root privilegies, that`s a good moment to change SPL. ezTerry`s tutorial i think is the best there is.
flash another rom. i am using now Nameless jedi`s rom maybe because i find it the best or just because i`m a star wars fan
i did not covered it all in this post ( i`m pretty sure ) so if your stuck in there somewhere ( android related ) you can IM me anytime. maybe we`ll even try a live installfest
p.s. the dreaimg.nbh is a "good to have" file. although i hope you`ll never use it.