Database Info

Black screen

Hi,
I try to change ROM from PDAMobiz Prophet WM6 V1.00 to Fantastic Mobiz XBow v1.1i. I made exactly what I was suppose to do. But after few minute i've got the error 300 "INVALID UPDATE TOOL". So I reset my S200, then it's stay on the blue page QTEK until I reset it. I try to upgrade again, but when i'm in the Bootloader mode, i connect the PDA, the letter USB appear on the PDA screen, but i've got the message "No device Connected, Would you like to try copying again", even if i still try few minutes later, it's stil say no device connected.
I don't know what can i do anymore.
Please need Help
Thanks for your help
Benjamin

What S200 you have? G3 or G4? What IPL/SPL Version?
Have you tested to use Step 2? Step 2 use a other Firmware Writer ...

G3
IPL: 2.10.0001
SPL: 2.20.0001
i don't know any other Firmware Writer. Can you tell me one please and where i can find it
thanks

ahm ... IPL/SPL with 0001 is a G4 ... have you write the G3 Firmware? if yes ... you have brick your phone!

by Brick , you mean it's definitly broken, i can do anything?
i was quit sure i used G3 version.

Do you have your dockingstation? Load your Batterie! Then try to enter the bootloader Mode! If you have black screen again ... send it back to you mobile provider and hope they exchange it.

no i don't have any dockstation.
so someone have more proposition please???

can you bring your device into bootloader screen?
from a first view it doesn't seem you bricked it (usually ipl and spl differ then (one is 0000 and one is 0001).
And as you still get an USB Icon i assume it is not broken (but i can't say that for sure).
Just try entering bootloader mode an then flash again (with a g4 firmware!) - see wiki for how to enter BL mode

Orange SPV M600 (HTC Prophet) Stuck in Bootloader

Guys,
I wonder if you can help. I have trawled this and many other forums and found many people that are having problems with their HTC Prophet or variations of the same device.
I have the Orange SPV M600, it was in my pocket and when I took it out to turn it on, it was displaying the bootloader screen after seemingly soft resetting itself. It is displaying the tri-colour bootloader with the following IPL/SPL
- IPL 2.10.0001 - SPL 2.10.0001
I have tried the following things that I have found in the forums:
1. Taking the battery out for 10 minutes ~ Still the same.
2. Hard Reset ~ I get the "Press SEND button to factory restore" message
but nothing happens when I push the call button.
3. Reflashing the ROM ~ I am unable to do this. I only have Vista and
WMDC does not see the phone in bootloader mode.
Is the phone dead? If so how could this have happened?
If anyone could help I would be eternally greatful. Oh and to add another complication the phone is still CID Locked
Thanks in advance
Barry

well if you where is south africa i would of helped you im sure if you have it runing on xp it will work my jamin did the same and all i did was push the camera button and reseted it got into tri colour mode and reflashed it
sorry that i could not help you but like i said if you in SA we could of tried it on my mashine

Any progress ?
did you ever get this sorted out ? Surely all you're gonna need is a PC with XP and active sync....
If I was closer you could have sent the phone to me and I would have had a go at reflashing the rom, but I'm at the other end of the country....

Hello guy here is a solution to flash under vista i have too a orange m600 and it works fine
http://www.modaco.com/RUU-Vista-done-u-t252977.html

help stuck on the bootlader screen?
guyz i have a jamin.. my cousin was flashin it and flashed the wrong software.. if i reset the phone it shows the boat loader screen!! and i cnat do anythin..caz u tell me which slftware to flash..and how to do it?? My freind told me all solution to my problem's will be solved here
hopin i will get my solution

First of all, download the NVID (no vender) AKU2.2 from here. http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe
Then, open activesync, select connection settings and UNCHECK the connect through USB option.
Then run the NVID file. It will take a while, and may seem to get stuck at 80% or 95%. Just leave it alone.
When that's done, you can either use it as it is, or load anyother ROM you want.

i have a bit similar problem
can some one plese guide me how to flash it with xp?????
Regards

First get a version of ActiveSync, any will do, but more recent is probably better. Then download the ROM (see above). In ActiveSync>Connection Settings uncheck the Connect through USB option. Then connect the Prophet.
Next Unzip the NVID file, and run RUU_PROPHET... This will flash your Prophet with a very basic ROM. If you then want to upgrade to a different ROM follow these steps: http://forum.xda-developers.com/showthread.php?t=310452

help in jamin stop in boot loader moood

hello to all
i have now device stop at 3 colure menu and not more
ipl 1.00
spl 2.20.0001
and can't start any room
can i use mtty like jasjar
or any advanced please ?????
thx to all

jamin G3 with SPL 2.13.0001
Hi:
Sorry my english isn't good. I'm spanish.
I read some forum but i don't read the same problem I've.
I've a imate jamin. Last sunday I installed a new rom made by Franlov (WM6.1 Clear). First i make a hardspl and installed the new rom. Well.
After i need install the original rom, but the problem now is:
Jamin KO.
Three color display and the red numbers:
IPL 2.13
SPL 2.13.0001
If I execute a romupdateutility G3, i've a error 300, invalid tool.
If I execute a romudateutility G4, i don't have error but i've the same display (three colors, etc)
I can't make a hardspl because the jamin doesn't run and msdos display says "any device connect".
CAn you help me?
I read it's possible downgrade ipl and spl making a force spl but the program i don't know if exist for jamin or s200.
THANKS
my email: [email protected]
THANKS THANKS THANKS THANKS

melmel1989 said:
hello to all
i have now device stop at 3 colure menu and not more
ipl 1.00
spl 2.20.0001
and can't start any room
can i use mtty like jasjar
or any advanced please ?????
thx to all
Click to expand...
Click to collapse
I have the same problem! I cannot active sync as it does not connect to the device. So I cannot flash.
IPL 2.13
SPL 2.13.0000
We tried but can not find solution!
I am tired of asking for help, and nothing!

Hi guys..im a newbie..been there myself...Wat u need to do is download the wm5 original rom from http://www.v-dog.net/XDA/PVTemp.zip & unzip it to sum location of ur pc then connect ur device & wen the 3 color screen comes run the RUU Utility G4... Thats it ...u'll be back to WM5

After that just follow this awsum guide by dioxda2 http://forum.xda-developers.com/showthread.php?t=353547

aia_6584 said:
Hi guys..im a newbie..been there myself...Wat u need to do is download the wm5 original rom from http://www.v-dog.net/XDA/PVTemp.zip & unzip it to sum location of ur pc then connect ur device & wen the 3 color screen comes run the RUU Utility G4... Thats it ...u'll be back to WM5
Click to expand...
Click to collapse
We tried! The problem is that active sync as it does not connect to the device.That is the big problem ....

TJSM said:
We tried! The problem is that active sync as it does not connect to the device.That is the big problem ....
Click to expand...
Click to collapse
1. go to my guide, download PVtemp first ~~~~
2, force the prophet to bootloader mode, (how to? see my thread)
3. plug back to USB ( rear PC USB port please...)
4. if you see the "USB" on the left bottom Prophet screen, YOU ARE DONE!!!!
5. Flash PVtemp NOW .... delay is bad~~~~

help me about this
hi,i have a IMATE JAMIN.my phone Does'nt boot after install wm6 & other program.when it turn on display
ipl2.13.0001
spl2.13.0001
gsm02.20.21
os10.2.0.8
after display a black screen & does nothing.
and USB Does'nt recognize my device.
can you help me?

have you tried to Hard Reset the unit after flashing to WM6.1?
You can try it by pressing CAMERA + COMM Button + Reset Button (for 3 seconds)

Stuck en bootloader

Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)

Please need some help ( a lot)

beastmichel said:
Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)
Click to expand...
Click to collapse
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and

Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??

beastmichel said:
Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??
Click to expand...
Click to collapse
1. you may safe your prophet ONLY if you successfully flash the NVID, (just don't look at the connection status between PC and Prophet, as it was forced to bootloader mode, just run the NVID and flash dtraight until it ends, be awared that, NVID needs time to flash, sometimes needs more than 5 minutes, so ... wait for it ! )
2. I hope you can make it or you need to bring your prophet to factory due to abnormal flashing (wrong flashing)...
Good luck
PS.
[size=+3]Lazytool......[/size]
you should place your favourite XXX.nbf file next to the "LazyTool-Start.cmd" or "upgrade.cmd", but [size=+3]NOT[/size] in the LIB folder.... +_+
+_+ +_+ +_+ +_+

too bad (
Dear dioxda2..
i think this is the same problem as my S200 (
mine wasnt on the software prob but hardware...
to: Threadstarter )
try bringing your Mobile to any qualified technician near your place.. something might have been wrong inside... like mine its the comm and cam buttons that are grounded thats why its always in bootloader.. no matter what software i flash its still the same...
hope this helps
Mark

Dear Marekplph,
Can you explain me what do you mean with grounded. Do you mean a
short circuit (negative). Is it dificult and expensive to fix ?
Thanks,very helpfull

dioxda2 said:
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and
Click to expand...
Click to collapse
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?

noonas said:
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?
Click to expand...
Click to collapse
if you want to make a fast move, bring it to the factory....
mess up upgrade code (G3 and G4) ... sorry... doomed.

back again
yes in my country its cheap.. coz something inside short circuited and that keeps my camera button pressed and taking pictures of his own < scary > if you cant fix this try to visit an authorized technician that can fix this for you...

ok, will send the s200 to the SAT (repair). I don´t have other options.

Flash a HTC tytn 2 O2 Impossible

Hello,
I search but not found the solution to hard spl for a O2 HTC TYTN2
(some of you talk about that problem : http://forum.xda-developers.com/showthread.php?t=334679&page=51 )
( white screen problem or stuck into tricolore mode )
it's seem that O2 have some different protection to avoid flashing
SPL 1.82.000
CPLD-8
hope to find a solution
Many thanks

I try to flash (HSPL) but i'm stuck on tricolore serial mode.
and white screen with this method : http://forum.xda-developers.com/showthread.php?t=354061
anybody have a solution ?
thanks

It's long ago since i've flashed my Kaiser- it may be necessary to first install enablerapi.cab to the root of your phone.
Then retry those jumpSPLs, followed by hardSPL.