High res screen replacement for zpad accomplished by Bigideas - G Tablet General

I am only an ordinary user not a Dev,i am only translating the information,any question should be posted on original threads.
It is a success, however it is a screen replacement of zpad not gtab, sorry for that since i thought the two is the same last time i post this,but they are very similar in hardware,so you maybe still want to see this
http://www.ez-pad.net/android-4254-1-1.html
and
this in english
http://www.hkepc.com/forum/viewthread.php?tid=1521745&extra=page=1
thanks for paying attention and i am not the person who did this
but they still do not have good ways to get the screen
on the original thread Bigideas also said that ten point multitouch IC replacement and tweaking is also on the way.
original thread http://www.ez-pad.net/android-3260-1-1.html
Can anyone find out where to buy the screen?
CPT TFT-LCD
CLAA101WB03
Display Area 222.7263(H)×125.2224(V)(mm) (10.1-inch diagonal)
Number of Pixels 1366×3(H)×768(V)
Pixel Pitch 0.16305(H)×0.16305(V) (mm)
Color Pixel Arrangement RGB vertical stripe
Display Mode Normally white
Number of Colors 262,144(6bits) (LVDS)
Gamut 42%(Min)/45%(Typ)
Optimum Viewing Angle 3 o’clock
Response Time 16ms (Typ)/25ms(Max)
Surface Treatment Anti Glare 3H
Viewing Angle 50°¡¢ 70° / 75°¡¢ 75°(Min)
Brightness 300 cd/m2 (5point) (Typ)
Uniformity
5point£º 80%
13point£º 65%
Consumption of Power (3.36)W(Max)
Module Size 249.3(W)×147.0 (H)×3.6(D) (mm) (Max)
ModuleWeight (180g) (Max)
Datasheet is in the attachment

That so new its not even listed on the manufacturer site
The only 10.1 hi res is
CLAA101WA01 on their website. The model you have listed does not show up yet, and so not available yet.

manikin13 said:
The only 10.1 hi res is
CLAA101WA01 on their website. The model you have listed does not show up yet, and so not available yet.
Click to expand...
Click to collapse
thanks for the information, CLAA101WA01 is 5.2mm in thickness and CLAA101WB03 is of 3.6mm in thickness which is the max thickness to fit in the case

mikeyaomikeyao said:
thanks for the information, CLAA101WA01 is 5.2mm in thickness and CLAA101WB03 is of 3.6mm in thickness which is the max thickness to fit in the case
Click to expand...
Click to collapse
True but not available as of yet. Once it is I will certainly be in line for one of these. If the specs are correct, that just puts the gtab over any other tablet on the market.

Is the file below your first post the re-hash that big idea made? Because I can't make heads or tails of the chinese site.

Roxxas049 said:
Is the file below your first post the re-hash that big idea made? Because I can't make heads or tails of the chinese site.
Click to expand...
Click to collapse
translate dot google dot com

DudeInMyrtleBeach said:
translate dot google dot com
Click to expand...
Click to collapse
Well if you bother to go to the site he linked, then you can see that google will translate it for you, but which button do you press to download the file?
The one I thought it would be asks for a user name and password.
Which takes me back to my ORIGINAL question, is the file the OP linked the file needed to change the resolution on the g tab if a new higher resolution screen is installed?

Sorry for not response. Time is different i went to sleep. If you visit the orginal site you will find a link which leads to exactly the same datasheet i gave in attachment here. no rom available since big ideas did not give. As she said she had borrowed the screen from a friend and get it work with a selfcompiled rom. but drop it to the ground and break it later. She asked for another one but only got only the datasheet of the screen

Attachment is a pdf so please extract it and read it. It is not something to change the res in rom.

Roxxas049 said:
Is the file below your first post the re-hash that big idea made? Because I can't make heads or tails of the chinese site.
Click to expand...
Click to collapse
I downloaded the pdf file of the original thread by big ideas and put it in my attachment.the hash do not meet the hash in the file name.

If you search LP101WH2 TLA2 on alibaba.com, there are many suppliers. Don't know whether its thickness fits though.

quick update now. in the original thread bigideas said she just order 5 of this kind of screens via a friend in HK. SO this thread is closed and we will wait, they may come to xda to tell the result themself.. thanks for paying attention.

i'm just seeing a slight issue here. The G-tablet's 1024x600 screen is a 16:10 display, whereas 1366x768 is 16:9.
Are the pixels on the high-res display non-square, and if so, is there any correction being done somewhere along the line?
EDIT; i checked your specs and nope, they're perfectly square. The g-tablet on the other hand DOES have non-square pixels and a physical aspect ratio close to 16:9.
This panel will be magnificent in the g-tablet

dagbro said:
i'm just seeing a slight issue here. The G-tablet's 1024x600 screen is a 16:10 display, whereas 1366x768 is 16:9.
Are the pixels on the high-res display non-square, and if so, is there any correction being done somewhere along the line?
EDIT; i checked your specs and nope, they're perfectly square. The g-tablet on the other hand DOES have non-square pixels and a physical aspect ratio close to 16:9.
This panel will be magnificent in the g-tablet
Click to expand...
Click to collapse
Maybe that can be a issue. but we will wait until bigideas post picture or video of the detail of screen replacement and the final effect and then make the decision wether or not it improves things and then i will follow them to buy the screen. there will be the need to flash into the rom bigideas has finished specially for the screen ,which may solve the problem of ratio,the rom is not posted now . the people on ezpad think the screen can give a better experience with the coming honeycomb which maybe still a little faraway so we pay a lot of attention to the thing. chenglu and bigideas are the legend of ezpad and i am only a ordinary user who loved xda and ezpad and wants to help.

sounds a lot like the new screen of A10. I believe they are the same.
http://www.jr.com/elocity/pe/ELY_A10_dot_4/

lets hope the screen fits and works with our tablet. If we had a good screen, this thing would be perfect

I'm totally new to the software side but can crack cases...curious if this is a fit?
bliss computers => lg-philips-lp101wh2-tl-a2-laptop-lcd-screen-10-1-wxga-hd-led.aspx (won't let me post links yet)
I emailed the sales department for recomendations ans confirmation on fit for the G tab...of course i'm clueless on what firmware/software mods would be needed. Just ordered mine from amazon so obviously I need to have a plan to gut the poor thing before it shows up

TxToast said:
I'm totally new to the software side but can crack cases...curious if this is a fit?
bliss computers => lg-philips-lp101wh2-tl-a2-laptop-lcd-screen-10-1-wxga-hd-led.aspx (won't let me post links yet)
I emailed the sales department for recomendations ans confirmation on fit for the G tab...of course i'm clueless on what firmware/software mods would be needed. Just ordered mine from amazon so obviously I need to have a plan to gut the poor thing before it shows up
Click to expand...
Click to collapse
Thickness is the priority when you choose your screen,most laptop screens are 5.2mm and the original screen is 3.6mm, our guys tried something made by lg and plugin with no change of software and it is thicker and only backlight on and nothing show up on the screen at all, when you are going to change the res i guess there are adjustment in something called timesequence or timegraph, you need to change things in driver in the rom,the thing you can see from a datasheet,i do not have experience with those things so my guess may be wrong. i can not tell you whether your screen will work or not, you can have a try if you like. i am also only a ordinary user who are waiting for the result, but i think this is the most promising attempt ever because bigideas seems to be capable of doing such adjustments.this is not yet a fit since no promised result and no detail pictures is released, you do not need to make your decision based on the information above whether you try your own screen or not

so let me see if i get this right?
an order has been placed for 5 screens that should "just work" upon install. correct?
they should have better viewing angles, higher res AND correct thickness?

dougmod said:
so let me see if i get this right?
an order has been placed for 5 screens that should "just work" upon install. correct?
they should have better viewing angles, higher res AND correct thickness?
Click to expand...
Click to collapse
If I'm reading this right, there has to be a ROM that addresses the screen resolution. It's not plug and play, but in theory it should work.

Related

Replace screen with Pixel Qi display?

First off, a quick big thanks to everyone here. This tablet is truly an awesome toy for tinkerers, and the folks here have made it a highly usable device with the custom ROMs.
My biggest (and really only) gripe with the hardware is that the screen has pretty rough viewing angles (especially when in landscape with the camera at the top). I'm curious if it would be possible to install a Pixel Qi screen (pixelqi.com/products). They are the same measurements and resolution (10.1" 1024x600), and they sell kits to replace your netbook screen for $275.
I'm going to head over to the teardown thread and see if I can located the connector for the screen and see if it is a match for what some of the listed compatible netbook screens have.
Has anyone here used/seen a Pixel Qi display?
Hellburger said:
First off, a quick big thanks to everyone here. This tablet is truly an awesome toy for tinkerers, and the folks here have made it a highly usable device with the custom ROMs.
My biggest (and really only) gripe with the hardware is that the screen has pretty rough viewing angles (especially when in landscape with the camera at the top). I'm curious if it would be possible to install a Pixel Qi screen (pixelqi.com/products). They are the same measurements and resolution (10.1" 1024x600), and they sell kits to replace your netbook screen for $275.
I'm going to head over to the teardown thread and see if I can located the connector for the screen and see if it is a match for what some of the listed compatible netbook screens have.
Has anyone here used/seen a Pixel Qi display?
Click to expand...
Click to collapse
Nope but if it works pls let us know. I would like to jump at that also =D
I love my GTab but with the Adam's announcement around the corner it may be best to wait until at least Dec 9th.
I Wanna see reviews on the Pixel Qi. from what ive seen its really good in the day light but is it very clear and no bad view angles indoors? does it look crisper? Brighter?
switt said:
I love my GTab but with the Adam's announcement around the corner it may be best to wait until at least Dec 9th.
Click to expand...
Click to collapse
+1
Sent from my computer using Ubuntu 10.10
No action?..wow..the screen SUCKS MONKEY BUTT other than that the device is great
azfxstb said:
No action?..wow..the screen SUCKS MONKEY BUTT other than that the device is great
Click to expand...
Click to collapse
Get a dock and use it on your TV or monitor
the viewing angle is worse on the pixel Qi, it's too thick to fit and has only low color(6 bit per color or 18bit total) that gets lower down to 64 greys in some lightings.
It's only good to lower power usage.

Replacement LCD for G Tablet!

Deleted first post. Stock screen is a no go. We need a new LCD all together
I was thinking about doing this, and if it is matte then that would make a difference. Just not sure if it is worth it, if the Adam comes out soon I may pick one up.
If you flip the Gtablet upside down, you will notice the angles look much better. Not sure why they mounted in a manner that has weaker angles, but it seems the most cost efficient way for a better display is if the connector, ribbon and bezel mount accommodated a 180 degree rotation
Adam is still in marketing concept stage for customer messaging. No word on their blog yet on distribution or mass production agreements by a contract manufacturer. Probably March release, if I were a betting person.
Hrmm well I Still wanna try this but I Probably wont get to it Untill atleast 2 more weeks. Broke till next pay check -_- Black Friday Deals Drained me....If all turns out good Ill post results.
http://shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=B101AW06&_sacat=See-All-Categories
HorsexD said:
Ok so I was Reading the Hardware Breakdown thread and saw that the Model for the lcd display used in the g tablet Is used on notebooks. So if I Buy a Replacement Screen of the same model im assuming it would work if put on correctly right? Well the one in the G tablet looks to be Matte Finish type which explains bad viewing angles but I found this website that sells 2 different types of lcd Displays that should be interchangable. the Next time i Get Payed im Gonna buy the Glossy Version wich should provide Better Viewing Angles and Superior Crispness and see if it work as planed. Could this be the Screen Problem Solution we have been waiting for? Heres the Link
http://www.laptopscreen.com/English/screen-part-number/B101AW06~V.1/
Hopfully it works with our tablet and Improves the Screen Angles! This might be worse for outdoors though. if you click 'Info' on glossy it explains more!
Click to expand...
Click to collapse
This sounds great let me know how it works out! My gTab arrived with about 10 dead pixels (most of them are small and i cant see them without being picky) and I am eager to try something else.
I thought viewsonic would be more picky about what kind of screens they put in their stuff.
These laptop screens might be the same, keep in mind. My netbook exhibits the same solarizing effect as my GTab - you just can't see it since you usually look at it head on.
roebeet said:
These laptop screens might be the same, keep in mind. My netbook exhibits the same solarizing effect as my GTab - you just can't see it since you usually look at it head on.
Click to expand...
Click to collapse
I know all my laptops have better viewing angles or at least richer blacks. So I do have some hope at improvement, since the panel in mine is so messed up.
Does anyone have any experience with these exact panels? any recommendations?
any reviews on this!
the screen from the Dell Inspiron Duo (if it has the same single connector) seems to have a lot better specs. It's supposed to be 1366*768 with much better viewing angles than this piece.
In fact, I'm considering returning my GTab for one.
t3h_g3n3r4l said:
the screen from the Dell Inspiron Duo (if it has the same single connector) seems to have a lot better specs. It's supposed to be 1366*768 with much better viewing angles than this piece.
In fact, I'm considering returning my GTab for one.
Click to expand...
Click to collapse
3.5 hour battery life? Ew! Though the screen is nice; if it fits I wouldn't mind getting one and putting it in.
Marine6680 said:
3.5 hour battery life? Ew! Though the screen is nice; if it fits I wouldn't mind getting one and putting it in.
Click to expand...
Click to collapse
Battery life isn't issue #1 for me. Usability is, and that's where the gtablet starts falling off for me. I feel that I can do a lot better for the money.
--
I think the issue with the Dell screen is going to be the connector. I get the feeling nobody else is using the tiny non-locking Molex connectors the gtablet uses.
To those looking for reviews, just Google "Pixel Qi Review", I can't post links otherwise I would do so. There's several articles on Engadget, and a few videos on Gizmodo and Slashgear. The idea behind Pixel Qi is that in sunlight you can disable the backlight, and the sunlight is reflected off the back (inside) of the screen; this makes the sunlight act as a backlight, resulting in being more viewable outdoors. Also, the display can be switched between 'normal' LCD and 'e-paper' style as well. Really, the biggest reason I'm interested is the viewing angles. Netbook LCDs have horrible viewing angles (the G Tablet's screen is a Netbook LCD), so I would love to see this tablet with a better display.
Pilxel qi seems to way way more expensive priced at almost 300$, Which is almost the price of another tablet. Also do they even make pixel qi screens that work on this tablet? I couldnt find it on the website
no-success said:
This sounds great let me know how it works out! My gTab arrived with about 10 dead pixels (most of them are small and i cant see them without being picky) and I am eager to try something else.
I thought viewsonic would be more picky about what kind of screens they put in their stuff.
Click to expand...
Click to collapse
Why wouldn't you return that?
katmandu421 said:
Why wouldn't you return that?
Click to expand...
Click to collapse
I just might, but i waited for a few weeks trying to pick one up. most of the pixel defects are small and right at the edge of the screen. there is one kind of annoying one right in the middle though :/
no-success said:
I just might, but i waited for a few weeks trying to pick one up. most of the pixel defects are small and right at the edge of the screen. there is one kind of annoying one right in the middle though :/
Click to expand...
Click to collapse
Return it! Complain! get a New one! dont stand for somthing less than satisfactory!
has anyone tried swapping out the screen?
It is my only gripe about the tablet lol.
Honestly i dont care though because all other tablets are priced 100-200 more and have lower hardware specs.
I can live with the screen considering it really isnt too bad... just by comparison it isnt as good as the iPad.
I cant compare 7" tablets though... because ... frankly they are 7 inches... you squeeze more pixels into a smaller screen and it will look nicer... simple as that.
If you think about it... us early g-tab adopters can hack ours up and when we want a new one ... probably sell a hacked up gtab for a pretty penny when we are done with it.
I'm not sure why there are so many complaints. How often are you going to look at a tablet at sharp angles?? The only legitimate angle that someone mentioned was if the tablet was laying flat on a table in front of you and you were reading an eBook or something.
Maybe it's just the way I use it, but I don't have a problem with the screen at all.
lostpilot28 said:
I'm not sure why there are so many complaints. How often are you going to look at a tablet at sharp angles?? The only legitimate angle that someone mentioned was if the tablet was laying flat on a table in front of you and you were reading an eBook or something.
Maybe it's just the way I use it, but I don't have a problem with the screen at all.
Click to expand...
Click to collapse
Landscape Mode is Fine but I Cant stand it when Im Trying to read a Book in Portrait mode. Kinda have to tilt it and it just looks stupid. This tablet is Best Landscape only. Thats why It Would be Nice to have a Better Screen With Better Angles. Theres 3 Versions of the LCD Screen I Mentioned on the first post. I Wonder if one of those would fit....hmmm....

Viewing Angle?

The only thing that is stopping me from pulling the trigger on the gtablet is the viewing angle issue that everyone is complaining about. Honestly I dont care how the screen looks if you are looking at it in an angle because one will always look straight into it anyways.. Other than this, what else is the issue with the screen?
Sears will be running a 10% off on this tomorrow AM bringing the price down to $342 and I need to make up my mind to grab it for that price.
Thanks in advance.
mspkash1 said:
The only thing that is stopping me from pulling the trigger on the gtablet is the viewing angle issue that everyone is complaining about. Honestly I dont care how the screen looks if you are looking at it in an angle because one will always look straight into it anyways.. Other than this, what else is the issue with the screen?
Sears will be running a 10% off on this tomorrow AM bringing the price down to $342 and I need to make up my mind to grab it for that price.
Thanks in advance.
Click to expand...
Click to collapse
Hi,
I'seen the comments about th screen, and while I'm not an expert on LCDs, I've never understood the complaints.
The screen on mine is bright, at 80%, and I don't notice much problem even at angles. I keep wondering if some Gtabs have different LCDs!
Jim
Probably the biggest issue I have is the solarizing effect that occurs when the screen is tipped back, while in landscape. This is something that is noticeable if you have the tablet flat on a desk and you are trying to view the screen that way. You can work around it by flipping the screen, but that doesn't work with all applications.
I don't think portrait mode is so bad, as I usually look at that straight on (it might be slightly high in contrast but you can turn it slightly to fix that).
IMO, viewing angle is not an issue but .... a privacy feature!
Definitely not a deal breaker for me. There are times where I wish I could get a wider angle, such as flat on a desk. However, it works fine for the majority of uses.
mspkash1 said:
The only thing that is stopping me from pulling the trigger on the gtablet is the viewing angle issue that everyone is complaining about. Honestly I dont care how the screen looks if you are looking at it in an angle because one will always look straight into it anyways.. Other than this, what else is the issue with the screen?
Sears will be running a 10% off on this tomorrow AM bringing the price down to $342 and I need to make up my mind to grab it for that price.
Thanks in advance.
Click to expand...
Click to collapse
Would be nice if they would run it at $349 again and the 10%. Let me know if they will give you the 10% on it as I will go get another.
Go check a Staples and see if they still have a demo unit out(they're apparently pulling it but some store might still have a demo unit out -- Sears just has a cheezy mockup...), or maybe an Office Depot...
The viewing angle really isn't so bad when you're using as I've found all the time that I'm holding or have it propped on my lap I have an almost dead view so the viewing angle limitation is not apparent.
As others have mentioned there have been a few times when I'd've liked a better viewing angle, such as when I have laying on the desktop while transferring files to it or having it do things and want a quick check of the screen status w/o have to crane over it...
My biggest remaining complaint is 10" form factor and weight, but mostly the 10" which makes it unwieldly which is why I'll eventually be adding a 7" to complement it, likely a Nook Color(NC) ATM although I'm resisting(strongly) running out and buying one any second now... (made it through Thursday & Friday w/o buying one... keep telling myself more tablets are on the way and to wait a bit although B&N seem to be the best at support so far, and given that they're still supporting the eInk Nook(Nook B&W? NBW?)...)
OTOH the 10" & weight allowed them to pack in a pretty decent battery, and I can manage a few days between charges which I'm sure no 7" will be able to manage, and especially not the NC... going to have to charge every night, and watch screen brightness & WiFi usage...
[EDIT]
Since I added in the Sears line above, it's funny I went to Sears to buy one of those crappy cases(VS $6 one), and the sales guy was laughing about how they have almost nothing in stock... He mentioned that because I asked if they had any other cases than that one, and he said that's it.. going on to mention of the two netbooks on display only the ASUS was in stock, they had 1 HDMI cable, 2 VGA cables(not sure what he meant by this one), a couple of ipods... pretty sad... I can't help but wonder if all Sears stores are like that or just that one... if they're all like that Sears is in trouble...
The Sylvania tablet display had disappeared too, since I was last there in mid-November... still had the white & black PDNs on display, along with a lone Sony eInk reader...
[/EDIT]
I got mine site unseen and also struggled with all the negativity before opening it. I finally broke down and gave it a go and can say I really love the device. Sure, the screen is probably its weakest link but far from the bleek picture painted in most reviews.
I guess many sites are holding the Gtab up to iPad standards. The screen is just a regular old netbook LCD. Viewing angles are made for landscape and looking down at 45 degrees. Everything outside that is pretty poor but typically that is how I hold the thing and the viewing angle doesn't bother me. Portrait is another story and if you want this thing to be an e-book reader (or anything) in that form factor then you will be sorely disappointed.
Viewing angle sucks big time and anyone who says otherwise is just trying to justify and otherwise good amchine they purchase and spent a lot of time getting to work properly.
It is a pain to type on in any kind of angle as the most comfortable angles make screen look negative polarity.
For straight on viewing I agree it's nice
I just got mine in sears with a 5% discount off of $379. I know the stock rom is junk and I dont even care as i'll flash it with vegan or tnt. I am trying hard to like the screen. In portrait mode, when viewing web pages, the text is alright but the pictures have this solarizing effect which I am not able to get over with.. darn.. why didnt they put a good screen on this otherwise a good power house.. will play around lil bit before deciding if i should keep it or send her back
Hi Guys,
Are all variants of the Malata tablet (including the GTablet) have the same LCD screen? I want a 10" Tegra 2 tablet with a better screen.
Thanks.
Canadoc said:
Viewing angle sucks big time and anyone who says otherwise is just trying to justify and otherwise good amchine they purchase and spent a lot of time getting to work properly.
It is a pain to type on in any kind of angle as the most comfortable angles make screen look negative polarity.
For straight on viewing I agree it's nice
Click to expand...
Click to collapse
You HAVE to have a different screen than the one I got. I can't get it to go negative no matter what angle I turn it too. The wife and I browsed the web for hours tonight and it worked perfectly, the viewing angle is much better than her hp laptop.
Sent from my SGH-T959 using XDA App
Maybe different batches have different screens. Mine is terrible if I hold it in portrait and look at it straight on. I have to tilt it to one side to make it usable unless it's completely dark.
WickedStyx said:
Maybe different batches have different screens. Mine is terrible if I hold it in portrait and look at it straight on. I have to tilt it to one side to make it usable unless it's completely dark.
Click to expand...
Click to collapse
My gtab has same problem in portrait.
cyberbillp said:
You HAVE to have a different screen than the one I got. I can't get it to go negative no matter what angle I turn it too. The wife and I browsed the web for hours tonight and it worked perfectly, the viewing angle is much better than her hp laptop.
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
You mind telling us where you got the GTab, and when? And your model # on the box? I wouldn't discount the possibility that you might have slightly different device than the rest of us.
I know that bekit had gotten a device that had different partitions than the "norm" - maybe the LCD is different, as well. All speculation, of course.
The viewing angle was the only thing I was worried about on this device prior to purchase as this was the main complaint, but after receiving it, its not as bad as some people made it to be, really some people are just really picky. I'm usually really anal about these things too but it is really not that bad.
WickedStyx said:
Maybe different batches have different screens. Mine is terrible if I hold it in portrait and look at it straight on. I have to tilt it to one side to make it usable unless it's completely dark.
Click to expand...
Click to collapse
Ditto whoever says it is good must own a white and orange cane
Canadoc said:
Ditto whoever says it is good must own a white and orange cane
Click to expand...
Click to collapse
There's a difference between good and good enough. The screen is good enough. Could be better, but works fine. I think most "positive" responses are of similar mind.
My workaround is to place a gum eraser underneath the top of the unit when I'm using it at the kitchen counter. The extra 1 1/2" of tilt helps viewing and the eraser doesn't slip.
An annoyance but definitely not a show stopper for me....
Can someone post a picture of what this viewing angle issue. I see so many references too it, bit I can't get a good visual of what people are taking about

Display doesn't take up the FULL screen?

Question to all of you Infinity owners. I don't have any major issues, light bleed, etc. However, i do have a concern about the 1mm or so black bar around the edge of the display between the black bezel and the actual displayed image (even on the main homescreens). Does your Infinity have this issue? It's not very noticeable, however, I am curious as to if I should exchange mine for a new one or if they are designed this way to not utilize the full display.
It's stock, not rooted, and not unlocked *yet If someone has the issue, please post PICS. I am at work and can't exactly do that with mine at the moment.
But, basically, it looks as if there is a 1mm or .5mm black "frame" around the display between the black bezel and the actual display imaged. Kinda reminds me of a double picture frame.
Can someone post a pic of there homescreen in as highest resolution possible, whether you have the issue or not so I can make a determination.
Thanks in advance
Mines got this, infact my phone and nook color has it too. Never noticed it before, probably will never notice after I hit enter. I imagine perhaps this is too keep light from the screen from bouncing off the framed bezel and creating a blur effect, just me guessing here.
Chief Geek said:
Mines got this, infact my phone and nook color has it too. Never noticed it before, probably will never notice after I hit enter. I imagine perhaps this is too keep light from the screen from bouncing off the framed bezel and creating a blur effect, just me guessing here.
Click to expand...
Click to collapse
Okay, thanks. I really appreciate it. I didn't notice it on the Prime I had....
Anyone else? Can you post PICS if you don't or do please??
Trying to determine if I should return it for a new one or leave as is....as said in the OP, I don't have any other issue other than this...if it is truly an issue or if it is designed that way...
pinky059 said:
Okay, thanks. I really appreciate it. I didn't notice it on the Prime I had....
Anyone else? Can you post PICS if you don't or do please??
Trying to determine if I should return it for a new one or leave as is....as said in the OP, I don't have any other issue other than this...if it is truly an issue or if it is designed that way...
Click to expand...
Click to collapse
Anyone..please...
pinky059 said:
Anyone..please...
Click to expand...
Click to collapse
It's by design, I have it too and so is my brother's tf700.
buhohitr said:
It's by design, I have it too and so is my brother's tf700.
Click to expand...
Click to collapse
It seems everything has this, there's even this slight boarder on mon monitors I'm looking at now (all 5 of them!)
Thanks....kinda what I thought, but what is odd is that I didn't notice it on my Prime or my EVO 4G LTE. I guess it makes sense cause if you view it from different angles WO this border, it would cut off a mm or so of the screen (not a big deal), but it may be for some people.
Alright, thanks....Will keep mine then...
pinky059 said:
Question to all of you Infinity owners. I don't have any major issues, light bleed, etc. However, i do have a concern about the 1mm or so black bar around the edge of the display between the black bezel and the actual displayed image (even on the main homescreens). Does your Infinity have this issue? It's not very noticeable, however, I am curious as to if I should exchange mine for a new one or if they are designed this way to not utilize the full display.
It's stock, not rooted, and not unlocked *yet If someone has the issue, please post PICS. I am at work and can't exactly do that with mine at the moment.
But, basically, it looks as if there is a 1mm or .5mm black "frame" around the display between the black bezel and the actual display imaged. Kinda reminds me of a double picture frame.
Can someone post a pic of there homescreen in as highest resolution possible, whether you have the issue or not so I can make a determination.
Thanks in advance
Click to expand...
Click to collapse
Try an alternate launcher such as Apex or Nova. You'll find that you can change the margin setting which allows you to use the entire screen using these launchers. I don't understand why the stock launcher wastes so much screen!

General The Bezels of the ROG 5 aren't Symmetrical!

Greetings, so I have been a proud owner of the ROG series since the beginning, I have owned the original ROG, and currently I still own the ROG 2 & 5. I haven't owned the ROG 3 because it wasn't much of an upgrade from the 2 and there were compromises as we all know with the headphone jack,.. etc.
Up until the ROG 5 the bezels of all the ROG phones were symmetrical, but not the case with the ROG 5. I am drawn to symmetry especially when it comes to phones, I hate unsymmetrical bezels or phones with notches thats why I keep avoiding flagship phones because none meet my preference (I know it's not a big deal but in my case unfortunately it is).
So coming back to the headline, I have measured the top and bottom bezels and the bottom bezel is smaller by almost a 0.5 mm - 1mm. I have been noticing it since the moment I got the phone but I kept doubting it until I measured it, also i didn't believe ASUS will do it since there was no justified reason for them to do it in the first place (Disappointed honestly because I love this phone dual speakers design out of all the ROG series).
Anyway I wanted to point it out for those people interested, since I haven't found any mention of it in any thread or website.
Device:
ASUS ROG 5 ( Chinese model CN_1005D)
12GB/128GB version
P.S : I added a photo of my phone scanned, then i measured it in Photoshop. This is what it turned out to be (As accurate as i could be ) ( A difference of 0.6 mm)
Are you sure it isn't a defect? Can't replicate your results.
twistedumbrella said:
Are you sure it isn't a defect? Can't replicate your results.
Click to expand...
Click to collapse
How can it be a defect, just by looking at the bezels from every angle you will notice that they aren't identical, now regarding the difference in measure I could be off but it's =<0.5 mm.
tyfor me it's perfectly even
Rashad83 said:
How can it be a defect, just by looking at the bezels from every angle you will notice that they aren't identical, now regarding the difference in measure I could be off but it's =<0.5 mm.
Click to expand...
Click to collapse
You answered your own question. Your bezels aren't identical.
Got out a ruler just to make sure and mine are a perfect 1 : 1 match.
@Rashad83 I always thought I was the only one
None of my friends ever understood my problems with most phones and their notches/punch holes and bezels.
I would rather have exact same bezels than a larger screen ratio.
Anyway back to the topic: thanks for your information. From the pictures it looked perfectly.
The first picture with the stickers on the display might seem off because the adhesive wasn't sticking but the drawn line is correct I assure you. I hate to say it but they aren't identical 100% sure!
So this is the bottom bezel with the sticker on it.
Now I took the bottom sticker and placed it on the top bezel, you can clearly see they aren't identical.
twistedumbrella said:
You answered your own question. Your bezels aren't identical.
Got out a ruler just to make sure and mine are a perfect 1 : 1 match.
Click to expand...
Click to collapse
I am happy for you if that is the case, but still I can't believe it's a defect because as I understand it these displays come out from the same mold used to create all the ROG 5 displays. Basically I couldn't be the only case with this issue, it's either all the ROG 5 devices are suffering from this issue or I am one of the few( Maybe not a few, will have to see) suffering from this issue.
Anyway thanks for the feedback.
Lol, you weren't suppose to notice this
Rashad83 said:
I am happy for you if that is the case, but still I can't believe it's a defect because as I understand it these displays come out from the same mold used to create all the ROG 5 displays. Basically I couldn't be the only case with this issue, it's either all the ROG 5 devices are suffering from this issue or I am one of the few( Maybe not a few, will have to see) suffering from this issue.
Anyway thanks for the feedback.
Click to expand...
Click to collapse
I never said you were the only case. Your issue would likely be an entire run (or location). I get that you are worked up about it, but a defect can be in the mold. It's still a defect.
What may be helpful is to post where you bought it and which version. There are two that work in the US, so this may be something that sways people if it only applies to one of them.
twistedumbrella said:
I never said you were the only case. Your issue would likely be an entire run (or location). I get that you are worked up about it, but a defect can be in the mold. It's still a defect.
What may be helpful is to post where you bought it and which version. There are two that work in the US, so this may be something that sways people if it only applies to one of them.
Click to expand...
Click to collapse
Thanks for the tip, the version I own is the Chinese version/model, i bought it locally so it wasn't shipped to abroad. The funny thing is that this is my second unit, the first unit I bought had scratches on the charger head so they replaced it for me. By the way I bought it from ASUS online official store.
Thread cleaned
please all, lets keep it on topic and with respect.
Thanks
Rashad83 said:
Thanks for the tip, the version I own is the Chinese version/model, i bought it locally so it wasn't shipped to abroad. The funny thing is that this is my second unit, the first unit I bought had scratches on the charger head so they replaced it for me. By the way I bought it from ASUS online official store.
Click to expand...
Click to collapse
That's actually really interesting. I know mine is Tencent, but it came with the WW firmware. I wonder if Taiwan got a separate manufacturing location.
So this topic got me interested in comparing other ASUS ROG 5 screen bezel sizes. I found this clear sample from Androidauthority Website , credits go to them .
I measured the length of the top (0.28 CM) and the bottom bezel (0.26 CM) in Photoshop, which results in a ratio of (1.076923076923077 : 1).
Now by my phone measurements the top bezel from the top speaker to the start of the display i get a measure of (~0.5 CM). Now if we multiply the ratio by the size i got, the bottom bezel should be (0.4642857142857143 CM). So a difference of ~ 0.4 MM.
Either way this proves that they aren't identical, It's not a big deal or a shocking discovery. None the less it's good to know for people wondering.
Rashad83 said:
So this topic got me interested in comparting other ASUS ROG 5 screen bezel sizes. I found this clear sample from Androidauthority Website , credits go to them .
I measured the length of the top (0.28 CM) and the bottom bezel (0.26 CM) in Photoshop, which results in a ratio of (1.076923076923077 : 1).
Now by my phone measurements the top bezel from the top speaker to the start of the display i get a measure of (~0.5 CM). Now if we multiply the ratio by the size i got, the bottom bezel should be (0.4642857142857143 CM). So a difference of ~ 0.4 MM.
Either way this proves that they aren't identical, It's not a big deal or a shocking discovery. None the less it's good to know for people wondering.
View attachment 5361477
Click to expand...
Click to collapse
Starting to sound like an old cigarette commercial. That extra whatever millimeters longer
I wouldn't be surprised if it is intentional. The more I was thinking about it, the screen protectors have a black top and bottom that partially cut into the screen. The manufacturer just assumes they are identical and ends up covering it up. That would explain varied results.
The camera in the top likely requires just slightly more space. The screen has to be a specific size, but they might not have been able to make the phone any taller. Rather than make the screen smaller or put the camera into the screen, you end up with slightly different sizes.
This phone could use even more top & bottom bezels if you ask me! If you use it for gaming with max touch responsiveness, you know what I'm talking about - a lot of accidental touches around the lower corners in landscape. Not cool when gaming. The area block function in A-Crate doesn't work for me.
In addition I wish the display corners were just good old full size square corners instead of being as rounded as they are.
Andrologic said:
This phone could use even more top & bottom bezels if you ask me! If you use it for gaming with max touch responsiveness, you know what I'm talking about - a lot of accidental touches around the lower corners in landscape. Not cool when gaming. The area block function in A-Crate doesn't work for me.
In addition I wish the display corners were just good old full size square corners instead of being as rounded as they are.
Click to expand...
Click to collapse
I cannot agree more. Unfortunately there is no newer phone that meets these requirements. However the rog 5 is the least guly one in my opinion.
I hope that "no bezel", Notch, Punch hole trend with rounded corners ends as soon as possible.

Categories

Resources