Related
Anyone else having trouble with wifi? I have a connection to my home network and have used the 10 digit hex wep key. Even in the same room as the router (Linksys/Cisco), the signal strength is only about 50% and I can't even open a page in Opera.
SSID shows correctly
Mode: Infrastructure
Tx Rate: 54Mbps
RX Rate: 1 Mbps <-- is this the issue?
Channel 1
Advanced status shows: Associated to network.
Any ideas?
hopper13 said:
Anyone else having trouble with wifi? I have a connection to my home network and have used the 10 digit hex wep key. Even in the same room as the router (Linksys/Cisco), the signal strength is only about 50% and I can't even open a page in Opera.
SSID shows correctly
Mode: Infrastructure
Tx Rate: 54Mbps
RX Rate: 1 Mbps <-- is this the issue?
Channel 1
Advanced status shows: Associated to network.
Any ideas?
Click to expand...
Click to collapse
Bump
A call to HTC yielded nothing. I'm at my wits-end. Just turning wifi makes it almost impossible to load a website, I do better with just my marginal 3G service even though the wifi shows connected. Do you think a hard reset might help??
hopper13 said:
Bump
A call to HTC yielded nothing. I'm at my wits-end. Just turning wifi makes it almost impossible to load a website, I do better with just my marginal 3G service even though the wifi shows connected. Do you think a hard reset might help??
Click to expand...
Click to collapse
I'd also reset the wireless router too. Another possibility is there might be compatibility issues between the router and fuze. what router do you use? i'm using a linksys router and it's working fine. Obviously the signal the phone gets isn't as good as my Thinkpad's signal, but it does the job fine. I'm really enjoying this 3G speed, so I don't really use wifi that much - saves power!
only wifi problem i had was when i put in my wep key it rejected it the first time, and when i made it reconnect everything was fine. but at first it said my network was unavail.
Okay, try this - it's what worked for me:
Go to Settings -> Connections -> Wireless LAN.
On the bottom, choose the Power Mode tab.
Move the slider all the way over to Best Performance.
Fixed me right up.
FuzzyLogic_FC said:
Okay, try this - it's what worked for me:
Go to Settings -> Connections -> Wireless LAN.
On the bottom, choose the Power Mode tab.
Move the slider all the way over to Best Performance.
Fixed me right up.
Click to expand...
Click to collapse
yea that worked for me....but this is gonna drain the battery alot quicker right? whay wont it work the other way?
FuzzyLogic_FC said:
Okay, try this - it's what worked for me:
Go to Settings -> Connections -> Wireless LAN.
On the bottom, choose the Power Mode tab.
Move the slider all the way over to Best Performance.
Fixed me right up.
Click to expand...
Click to collapse
I found that in a windows mobile support forum as a stated solution for anothe HTC project and tried it also, it worked!
Thanks!
I'm having problems connecting to a WPA encrypted router and it's driving me crazy.
It just hangs and hangs and hangs, but never connects. If I put in an incorrect pass, or bad info- it immediately will fail to connect, but with the correct info- it will continue to attempt to connect, but never finish.
I've changed it to "Best Performance" but that made no difference.
^ Happened to me also. Turned out that I didn't add the Fuze's MAC address to my router's allowed devices list in wireless security.
I'm having the same problems as OP. I'm using the Fuze straight out from the box and I've tried adjusting the power settings as suggested and still no luck. I've also hard resetted to no avail. Any help is appreciated, thanks.
I don't have any issues with my wireless network, but I don't use an WPA encrypted router.
I have mine set to MAC address, and it work without issues.
I have a WEP encrypted router and it shows that I am connected. Do I need to set something up in settings -> connection -> connection? All I have are Media Net and "Work" listed. Seems like no one else is having this problem =/
I'm having a similar problem with my phone. I set my phone to maximum signal and the battery is just taking a hit. I can barely get a signal although it does work. I can't get the "free" ringtone to download off of their website, but no big loss. Wondering if the 3G/Edge would be a better bet.
Im also having a problem connecting to my network. it shows that im connected but doesnt now connect to the internet in internet explorer and other online apps. ive tryed...
restarting the router.
hard reset.
changing the power settings to high performance.
disabled hidden proxy as suggested on another thread.
exchanged my phone after being suggested by htc.
im using a linksys router. is it a compatibility issue?
this is driving me crazy; why are so many people having this problem?
I dont know if this goes here, but reading your problems, I think mine is a little different.
Where I live, in Mexico, almost everyone has internet service with the same Isp, who gives 2wire dlsmodem/routers with only a 10 digits wep encription (for default), the problem I have is that whenever I try to connect to any router (I've only tried with these) it asks for the wep key, but no matter what I put it always says that is incorrect. I tried disabling the encription and IT DOES work, but I dont control the other routers wich I want to connect to..
Any Ideas?
I am having the exact same problem. I could connect to an unsecured hotspot but can not connect to my WEP protected linksys/cisco router. It appears that linksys/cisco seems to keep popping up in this thread from folks having problem. Out of curiosity what model number of linksys/cisco do you have? Has anyone figured out a solution yet?
Go to configure wireless networks than go to the network adapters tab, click the first one IEEE 802.11 bg .... and make sure its set to user server assigned IP address.
Same problem here! tx @ 54 mbps rx @ 1mbps, and it doesn't change therefore i'm getting about 5meters distance before my connection becomes unstable (WTF). Using WPA2-PSK and set to performance.
P.S. all router incompatible comments are incorrect. There's a spec for .11 b/g and all hardware should be using this therefore it should work it's either a hardware fault or some settings aren't working correctly. BTW for me it's the same prob whether changing the ROM or radio, it doesn't change...
Same problem...never resolved? Fuze $200
http://forum.xda-developers.com/showpost.php?p=4213175&postcount=19
Solution
I may have a solution, it worked for me on 3 routers so far and dramatically increased reception over distance and connection stability.
Open your WiFi router settings, go to advanced settings and look for something like Beacon Period. If I got it right, this is the interval between position updates and default setting should be 100.
If you lower this number, it will update your devices position more accurately and get you better stability.
Be warned it will probably marginally increase AP radiation and decrease bandwidth of the wifi connection by a percent or two, however I didn't notice any difference but a huge stability increase.
I am using Beacon Period 50 at home but anything from 50-75 works for me.
Enjoy
My fuze's wifi worked fine with a Zyxel router and a Belkin router configured as a dd-wrt repeater, for 6 months. Last week, verizon came to install FIOS and upgraded their old non-wireless router with a new one. Since then my Fuze can't see internet through wifi anymore. And it doesn't see the router's home page at 192.168.1.1 either.
However it is able to join the wireless network (WEP, SPA2, etc password portected) and get an ip address through DHCP or static. If it is static IP, then the router can see it as a static IP. My other wireless devices can all connect to the new router, including an iphone and the dd-wrt router configured as a client.
Initially I thought it was some silly settings between the new router and the phone. But after I exhausted things to try, I put the old Zyxel back on, and it still doesn't work. I also checked Fuze with our public library's open wifi, no luck either.
I just did a hard reset, reloaded the at&t rom, still same problem.
I did search the forum, and found a related thread, with no solutions in it--http://forum.xda-developers.com/showthread.php?t=441889
Any help is greatly appreciated!
ETA: A number of people mentioned the power setting of wifi needs to be set to max performance. While I have always had my set at max battery, and wifi worked find perfectly until the change described above, now I set it to max performance it is working. And set it to middle or any other place it doesn't work. I think it is some response time setting on the router.
Not sure if you've tried this, but figure I'd mention it anyway in case you forgot. I'm not too sure what this does myself, but isn't there a setting to tell the Fuze to connect through the "Internet" instead of "Media Net" or something like that? Maybe you forgot to change that setting, but it doesn't really make sense why getting a new router would be the cause of loss of wifi, unless the wifi chip went bad at the same time you got the router, which I don't think is likely?
Under wi-fi settings there is a choice between connecting to "The Internet" or "Work". But my phone has always been set to internet.
MediaNet is about the cellular signal's data service. I am using it it for the GPRS and 3G setting.
resolve: power setting did it
A number of people mentioned the power setting of wifi needs to be set to max performance. While I have always had my wifi set at max battery which is the default setting, and wifi worked find perfectly until the change described above, now I set it to max performance it is working. And set it to middle or any other place it doesn't work.
I think it is some response time setting on the router that is affecting it. My old router must be more forgiving.
Thanks
Changing the wifi battery setting from Best to performance worked. Thanks, I was getting frustrated.
Power Settings
Hi any one knows why does the Fuze has to be set to best performance for wifi to work. do we have any solution to come over this issue.
jhogal1 said:
Hi any one knows why does the Fuze has to be set to best performance for wifi to work. do we have any solution to come over this issue.
Click to expand...
Click to collapse
on my fuze, wifi works when it is on max battery.
Hello all!
Not sure if this has been posted but I figured I would put up a new post. I am showing that I am connected to my home WiFi but I am not able to actually use it. For instance, I cannot open links or watch YouTube videos. I believe it is the router because I just had a Droid RAZR and my connections to the Internet were not dependable. Currently, I am using AT&T's 2Wire 2701HG-B Gateway router.
Are there any settings that should be adjusted within the router? Encryption type is WPA-PSK. Wireless mode is 802.11g/b.
I just got my S3 yesterday and so far WiFi works in other places. Also, I tried the #*0011# thing and that did not work for me. I've rebooted and factory reset my device. Nothing helps. Anything I can change?
Thanks in advance!
Does your router Administration panel (perhaps accessed via a web browser?) show your phone as connected with an assigned IP address?
- ooofest
ooofest said:
Does your router Administration panel (perhaps accessed via a web browser?) show your phone as connected with an assigned IP address?
- ooofest
Click to expand...
Click to collapse
Now that I'm looking, no it doesn't have it listed there. My phone says its connoted though. I forgot the connection, rebooted the phone and did the #*0011# and reconnected the network. Still the same result. Any ideas?
I've seen some routers being a bit buggy about showing all wireless-connected devices (my dual-band Netgear comes to mind), so I can only think of a few things to check:
This assumes your router is configured for DHCP and that you have addresses available in its configured range, etc.
1. Does anything else use this router successfully to access the Internet?
2. On your phone, Settings -> Wi-Fi->(click on the wireless network you are "Connected" to)->View, does it show an expected speed and a valid IP address from your router?
3. If (2.) revealed a valid IP address on the phone, can you ping that address from another system attached to the same router?
4. Did you connect the phone using a typed-in passphrase on both router and phone or by using the Wi-Fi Protected Setup (WPS) push-button method on the router? I found that, no matter how carefully I typed the passphrase, it often would not connect to my desired network because something was somehow amiss. However, this phone is compatible with using WPS, so I used the router's push-button method and it connected easily + worked fine.
Just some things to check and ensure nothing critical is amiss.
- ooofest
ooofest said:
I've seen some routers being a bit buggy about showing all wireless-connected devices (my dual-band Netgear comes to mind), so I can only think of a few things to check:
This assumes your router is configured for DHCP and that you have addresses available in its configured range, etc.
1. Does anything else use this router successfully to access the Internet?
2. On your phone, Settings -> Wi-Fi->(click on the wireless network you are "Connected" to)->View, does it show an expected speed and a valid IP address from your router?
3. If (2.) revealed a valid IP address on the phone, can you ping that address from another system attached to the same router?
4. Did you connect the phone using a typed-in passphrase on both router and phone or by using the Wi-Fi Protected Setup (WPS) push-button method on the router? I found that, no matter how carefully I typed the passphrase, it often would not connect to my desired network because something was somehow amiss. However, this phone is compatible with using WPS, so I used the router's push-button method and it connected easily + worked fine.
Just some things to check and ensure nothing critical is amiss.
- ooofest
Click to expand...
Click to collapse
1. Yes, my iPad and two laptops.
2. There is a link speed and an IP address but the third number of the IP address on my phone is different than the third number of the IP addresses of the devices listed that connect to the router. I hope I made some type of sense saying that lol! There are about 6 devices listed that connect to the router and the first, second and third numbers are the same. My phone only have the first & second numbers in common.
3. didn't try that because I'm assuming something isn't right from the previous answer.
4. I typed in the pass phrase from my phone. I do not know of any other way to connect the device. I am not familiar with doing it from the admin panel especially since I'm not even seeing the device there.
Thanks again!
Yeah, not getting the proper address range would be indicative of a problem authenticating with the router, I'd suspect. If you are using the default router configuration, it should have an IP address of 192.168.1.x, where x = {some number}
You might try temporarily setting the router to "WEP-Open" and no passphrase on the phone (i.e., connect to the open network) to determine if the phone can obtain a valid IP address from this router before doing more debugging. This might weed out the possibility that this new phone has an inherent problem connecting with your specific router - even though other devices don't have such issues, maybe the Galaxy S III is sensitive in this regard.
Consider ensuring that the "Power setting" in your wireless configuration is at its maximum value (10?).
Aside, I don't know if the latest firmware enables WPA2-PSK, but that utilizes AES and is often more efficient than WPA-PSK, from my understanding. If using WEP-Open works for your new phone in the above test, then consider setting the router to "WPA-PSK and WPA2-PSK" (if it has that value) and try reconnecting using the passphrase (either 10 or 26 letters/numbers) - that setting should be compatible with your other devices and not require them to be reconfigured, I believe.
This topic seems to indicate people have problems with your model of router in making and keeping wireless connections at times, sometimes needing to hardcode the router down to only use "b" protocol (i.e., slower) for maintaining stable connections. I don't think that's the case here, though.
This User Guide (.pdf) for your router model does not seem to show that it offers WPS as an alternative for establishing device connectivity. From my recollection, my phone would only connect reliably to the router using encryption when I used the WPS button on the router. That's why I asked you to set your router to be Open for a test.
- ooofest
I had the same issue as you. I would be connected to my router and nothing at all. I am using a att modem/router along with my netgear wndr3800. But wifi was dropping a lot of the time. I never had this problem before when I had my Rezound. 3 days before I got my S3 I upgraded the firmware on my netgear router. I am guessing my S3 didn't like the firmware update or something. I tried everything in the router settings to doing a factory reset on both the att modem and my netgear router. Nothing... So I honestly thought it was my phone. Called Verizon and asked them to ship me a refurbished. So, I thought I would try one more thing. Revert back to my old firmware on the netgear router. Well it worked. Since Friday night I haven't had the issue you are having. Connected to my home wifi with no drops at all. It could be the firmware. Wonder if you could revert back. On a att modem/router I am not sure.
Sent from my Samsung Galaxy S3
ooofest said:
Yeah, not getting the proper address range would be indicative of a problem authenticating with the router, I'd suspect. If you are using the default router configuration, it should have an IP address of 192.168.1.x, where x = {some number}
You might try temporarily setting the router to "WEP-Open" and no passphrase on the phone (i.e., connect to the open network) to determine if the phone can obtain a valid IP address from this router before doing more debugging. This might weed out the possibility that this new phone has an inherent problem connecting with your specific router - even though other devices don't have such issues, maybe the Galaxy S III is sensitive in this regard.
Consider ensuring that the "Power setting" in your wireless configuration is at its maximum value (10?).
Aside, I don't know if the latest firmware enables WPA2-PSK, but that utilizes AES and is often more efficient than WPA-PSK, from my understanding. If using WEP-Open works for your new phone in the above test, then consider setting the router to "WPA-PSK and WPA2-PSK" (if it has that value) and try reconnecting using the passphrase (either 10 or 26 letters/numbers) - that setting should be compatible with your other devices and not require them to be reconfigured, I believe.
This topic seems to indicate people have problems with your model of router in making and keeping wireless connections at times, sometimes needing to hardcode the router down to only use "b" protocol (i.e., slower) for maintaining stable connections. I don't think that's the case here, though.
This User Guide (.pdf) for your router model does not seem to show that it offers WPS as an alternative for establishing device connectivity. From my recollection, my phone would only connect reliably to the router using encryption when I used the WPS button on the router. That's why I asked you to set your router to be Open for a test.
- ooofest
Click to expand...
Click to collapse
I tried WEEP-Open and that did not allow me to connect either. I did set up WPA2 but I still was not able to connect. The power setting was set to 10. Not sure how to manually add the device which I was going to try. I've forgot it several times and added it again but it does not work. I did connect at a different location. Not sure what else to try. Even tried changing the channel.
iLogikk said:
I tried WEEP-Open and that did not allow me to connect either. I did set up WPA2 but I still was not able to connect. The power setting was set to 10. Not sure how to manually add the device which I was going to try. I've forgot it several times and added it again but it does not work. I did connect at a different location. Not sure what else to try. Even tried changing the channel.
Click to expand...
Click to collapse
If it's not connecting to your router with WEP-Open, then something different is going on. I looked in the manual for MAC Address access lists, but that doesn't appear to be a feature of this router (unless it was added in a firmware update which came after the manual was published - if this was the case, your laptops and iDevice would have had their MAC addresses added to the router as another layer of access control to the WiFi network).
Sorry, I'm out of ideas on this one. You seemed to say that the Samsung connects to other WiFi points, so perhaps there is an inherent incompatibility between this router model and your phone which can be reported to Samsung and/or Verizon Tech Support - for all we know, this is a known issue.
- ooofest
ooofest said:
If it's not connecting to your router with WEP-Open, then something different is going on. I looked in the manual for MAC Address access lists, but that doesn't appear to be a feature of this router (unless it was added in a firmware update which came after the manual was published - if this was the case, your laptops and iDevice would have had their MAC addresses added to the router as another layer of access control to the WiFi network).
Sorry, I'm out of ideas on this one. You seemed to say that the Samsung connects to other WiFi points, so perhaps there is an inherent incompatibility between this router model and your phone which can be reported to Samsung and/or Verizon Tech Support - for all we know, this is a known issue.
- ooofest
Click to expand...
Click to collapse
Thank you for all of your help!
Rams99 said:
I had the same issue as you. I would be connected to my router and nothing at all. I am using a att modem/router along with my netgear wndr3800. But wifi was dropping a lot of the time. I never had this problem before when I had my Rezound. 3 days before I got my S3 I upgraded the firmware on my netgear router. I am guessing my S3 didn't like the firmware update or something. I tried everything in the router settings to doing a factory reset on both the att modem and my netgear router. Nothing... So I honestly thought it was my phone. Called Verizon and asked them to ship me a refurbished. So, I thought I would try one more thing. Revert back to my old firmware on the netgear router. Well it worked. Since Friday night I haven't had the issue you are having. Connected to my home wifi with no drops at all. It could be the firmware. Wonder if you could revert back. On a att modem/router I am not sure.
Sent from my Samsung Galaxy S3
Click to expand...
Click to collapse
I've tried every way possible to find a way to revert back but it does not work. No success. I've noticed that this S3, my old razr, & another android phone does not actually connect. The comet (3rd phone) actually appears on the the panel but the ip address on the phone is different than what is showing on the admin page for my router. The phone does show whereas the razr and s3 never even appear in the list though they say they are connected.
I'm at a dead end
iLogikk said:
I've tried every way possible to find a way to revert back but it does not work. No success. I've noticed that this S3, my old razr, & another android phone does not actually connect. The comet (3rd phone) actually appears on the the panel but the ip address on the phone is different than what is showing on the admin page for my router. The phone does show whereas the razr and s3 never even appear in the list though they say they are connected.
I'm at a dead end
Click to expand...
Click to collapse
To be honest. It's not your phone. I think you said you already did a factory reset on the modem/router correct? If not, do it and revert back to factory settings. If that doesn't work I would call att and tell them to send you another att modem/router. Tell them your wifi is down. Hopefully you'll get everything back to where it was. Good luck.
Sent from my Samsung Galaxy S3
Fix
This is what finally worked after two weeks of researching! Found this here for the toshiba thrive but it worked for mr! http://www.thriveforums.org/forum/t...1-thrive-will-not-connect-t-2wire-router.html
I tried this part but all of my settings were already set to match this....including it because it was part of the process.
--------------------------------------------------------------------------------------------------------------------------------------------------------------
Originally Posted by shakefry
My little sister received a cool Toshiba Thrive for Christmas but the thing will not connect to the proprietary router we have. The router isn't the problem because I've been able to connect a Macbook, 2 PCs, a 3DS and a smartphone to it and they all work as needed. When we put in the password for the connection it saying it is 'scanning' and 'connecting' then disconnects and starts going into a scanning loop saying is scanning then stopping then starting again.
I found a similar topic about this but the thread did not answer my question. I followed all of the steps of given solutions to no avail. And the constant suggestion to set the beacon or preamble differently is highly frustrating because the model router I have does not have such settings (I have gone through all the menus about ten times, literally).
I have also heard that the connection security could be a factor but I am not willing to downgrade my WPA 2 (TKIP & AES) to a WPA 1 or WEP, unless its absolutely necessary. I've been googling for hours so I need a solution or unfortunately we will have to return it for a more compatible device, which would suck because we got this for a good price (new).
Our router is a 2WIRE 3800 hgv-b (we have AT&T Uverse, idk if I should specify anything else)
Any help would be greatly appreciated.
Hi shakefry - Nice to meet you. You are 100 percent right you should not lower your security - WPA2 is the strongest and it does work fine with Thrive. That is what I use.
For some reason the ATT 2-wire routers are the most frustrating, but that is not a problem. We just might have to try a few different things, instead of getting it to connect the first time, so stay with me, OK? big brothers always have to help their little sisters...
----
1. You do not have MAC Filtering enabled,do you? If you do add the Thrive's MAC to the Router's list of permitted devices. Then try connecting.....
2. Not using MAC Filtering, or you added the thrive and still can not connect ......
OK, First ... Lets get the info your Windows Laptop has about your router when it connects
successfully to the 3800HG-B Router via wifi:
On your (Win7?) PC that is successfully connected by wifi to the same network, lets get some wifi settings. Vista - pretty much the same screens, XP a little different looking.
Click on the wifi signal lower right taskbar, open network and sharing center.
click on right side in blue, your network name
Pop up window - click on Details
the detail window opens ...
IPv4 Subnet Mask should be 255.255.255.0, if not we need to change it in the router settings.
This would prevent you from getting to the internet, but with all devices not just thrive.
Copy down IPv4 Default Gateway, and both IPv4 Servers
(Most routers will not need the actual IPv4 addresses in the devices DNS1 and DNS2, but yours might)
Now (no picture) close the DETAILS window and click on WIRELESS PROPERTIES. click on SECURITY tab, then click on SHOW PASSWORD. DO NOT CHANGE THIS FIELD, YOUR PC WILL DISCONNECT. WHAT YOU SEE IN THIS FIELD IS THE CORRECT PASSWORD TO YOUR NETWORK.
(I just want to be 100 percent sure - this is the password you need to log the thrive on. You are pretty sharp with all this stuff, so you know it is case sensitive, don't mistake a "zero" for the cap letter O, etc.
We will try using these when we set Thrive's wifi settings for your network.
(Go to link to find the screenshot)
Now please check the following router summary page by logging on to your router.
Make sure, on the right side it, shows enough DHCP Available, and on that the router
address is still 192.168.1.254
And on the left, the page is exactly the same as below, none of the blank fields are filled in, right?
And the top button is still selected ..... 192.168.1.0/255.255.255.0 (default)
--------------------------------------------------------------------------------------------------------------------------------------------------------------
THIS IS WHERE THE ACTUAL FIX CAME IN
Originally Posted by shakefry
"Would it possibly help if i DID enable filtering? then I could just put in all the device's MAC addresses and maybe it'll be more focused or something?"
No filtering wont "pull in" the devices, through the front door of the router. Filtering will just turn them around and kick them out again if they are not on the "invited to the party" List.
"edit: I just found a similar page, the design is slightly different. The router/gateway address is one number above my DHCP range and it says I have 178 available and there are 12 allocated (weird because we only have 10 devices connected to this thing that I know of)
OK so you have plenty of available IP addresses (DHCP). It is normal to see a couple more than the number of devices you have."
So now you have the info you need to connect the thrive (maybe):
1-Hold the Thrive in portrait mode so the keyboard does not hide the settings
...
2- Go to Settings >> Wireless and Networks >> Wi-Fi settings >> tap your network name, Tap FORGET
Now when your network name shows up again under wifi settings ....
select WPA2
Enter password, it is case sensitive.
3- tap the triangle where it says DHCP, select "static"
enter 192.168.1.173. (a nice odd numbered unused ip, away from the auto assigned ones).
(You are making it an odd number (173) because if you buy, in the future, something like a network drive, or AppleTV, it will probably come with a nice "multiple of five" static number like 150 or 155 or 35
the "CONNECT" is greyed out .... right?
4- enter routers gateway 192.168.1.254
enter prefix 24
enter dns1 192.168.1.254
5- the"CONNECT" brightened up again? Tap CONNECT.
....... OR ..........
CONNECT is still greyed out? Enter DNS2 192.168.1.254, tap CONNECT
ARE YOU CONNECTED???
If NO
1- update the router's firmware - try connecting again
2- We will give up on the 3800 and add your second router, with different sets of DHCP ranges, and broadcasting on a non-conflicting channels to the 3800's channel ( channels 1, 6, and 11 do not conflict with each other - assign one router to channel one and the other to channel 11, and keep them a couple of feet away from each other.
shakefry, Please Let us know how it goes, which solution worked ... so other forum readers can help their little sisters too ....
we are standing by (actually in my comfy recliner waiting ..)
Thanks, bobj
aka Bojo, or Obi-Wan, or RouterRooter
I was able to connect to wifi consistently and access the Internet and YouTube app successfully. Hope this helps someone else!!!
Source: http://www.thriveforums.org/forum/t...1-thrive-will-not-connect-t-2wire-router.html
Glad to hear you got it going. I actually fixed mine about 3 days ago. I read somewhere changing your ssid inside the router helps. Well, I did and it actually worked. I haven't had a problem with my wifi signal yet. On mine what was happening also was whenever my phone would go into sleep for say 5min and I went to use the Internet immediately. It would take the wifi about 20-30secs for the wifi to wake up. So far, since changing my ssid I haven't had that problem at all.
Sent from my Samsung Galaxy S3
iLogikk said:
This is what finally worked after two weeks of researching! Found this here for the toshiba thrive but it worked for mr!
. . .
2- Go to Settings >> Wireless and Networks >> Wi-Fi settings >> tap your network name, Tap FORGET
Now when your network name shows up again under wifi settings ....
select WPA2
Enter password, it is case sensitive.
3- tap the triangle where it says DHCP, select "static"
. . .
4- enter routers gateway 192.168.1.254
enter prefix 24
enter dns1 192.168.1.254
5- the"CONNECT" brightened up again? Tap CONNECT.
....... OR ..........
CONNECT is still greyed out? Enter DNS2 192.168.1.254, tap CONNECT
. . .
Source: http://www.thriveforums.org/forum/t...1-thrive-will-not-connect-t-2wire-router.html
Click to expand...
Click to collapse
Thanks for posting a followup.
Did you delete and re-add the WiFi network on your phone, configuring it for a static route and IP address that was in the range on the router, essentially?
- ooofest
Dear XDA members.
I purchased my D820 Nexus 5 a couple of days ago, connected to my home router to set things up but then I noticed something, the device is connected to the router in every single room in the house with at least a fair-strength connection but I actually don't have Internet access unless I'm about 6-10 ft away from the router which is a bother.
Things I tried:
-Restarted router
-Connected to router using other devices
-Edited router settings flipping between 802.11 b/g/n bands
-Changed security type and encryption
-Used a static IP connection instead of a DHCP
-Installed two different roms to test the connection (CM11, Mahdi)
-Installed Wifi analyzer,apk to check surrounding traffic (to avoid wireless interference) and then changed router channel to a suitable one.
I have searched loads of websites and haven't found any working solutions, I'm so desperate for help.
Sorry for writing a long thread and thanks in advance.
Frogi.
In your phone's advanced WiFi settings there is the option to choose between 2.4Ghz or 5Ghz try those. If that doesn't work trying flipping the mobile data switch off and see if that helps.
bblzd said:
In your phone's advanced WiFi settings there is the option to choose between 2.4Ghz or 5Ghz try those. If that doesn't work trying flipping the mobile data switch off and see if that helps.
Click to expand...
Click to collapse
I have tried that, no luck
What happens if you remove any security type and encription?
This problem happened spontaneously with all the android devices in our house. Router had been set up for a month with great performance and then the day before yesterday things just got crappy on our wifi.
Here's the problem:
There's a significant lag between trying to get data (refresh Facebook app, load a Youtube video, go to a web page in Chrome, whatever) and actually getting the data. This occurs on two Nexus 5 phones running Lollipop and a tablet running Kit Kat. Sometimes it'll be 10 to almost 30 seconds between trying to view, for instance a youtube link, and the video description and video actually starts to load. Sometimes I'll get a network timeout. A laptop running Arch Linux on the same network has no such lag.
Here's the weird thing. When I do a speedtest with the Ookla app, it will take a VERY long time to "find the best server" (it's been a minute so far while I've been writing this post just sitting at that screen) but once it does I'll get really excellent speeds. Basically maxing out the possibility of my home internet connection (40Mbps+). Same with upload (13Mbps). Ping to server was 10ms. When I use a terminal emulator to ping a site like google or facebook it will ping with typical wifi reaction rates, usually under 25ms consistently.
Wifi reception on the 2.4Ghz band is great. throughout the house. Different wifi channels do nothing. Note, my wi-fi signal is not dropping, so it's not that issue that's often reported. Reception is great, there's just major lag between trying to get data, and actually connecting.
And again this isn't just one device, this is three separate devices running two different flavors of android. So I'm guessing my router one day decided it didn't like android. Because like I said, things were great until literally just Thursday, with no change in settings on any devices or the router from us.
Yes, I've done a power cycle on the router, which is a Netgear C3700
Any ideas on what might be happening?
It's possible there is an IP addresses conflict. Do any devices on the network have a static IP?
No IP conflicts that I can see ever have been the issue.
If I reboot the router the problem goes away for a couple hours, but then I get the WiFi lag soon enough. I've seen a lot of reports about lag on WiFi (with bad ping results) on some other google searches I've run, but they all point to problems with IPV6, which my router doesn't support at all, so there's nothing for me to turn off there. I can't find any IPV6 settings for anything anywhere on the phone itself.
I don't see any other problems with my router and android devices specifically mentioned anywhere.
Are your android devices using different DNS servers than that of your laptop?
I have never specifically set up any DNS settings on any device in the house. Not even sure how to see what the settings for that are on the Android devices.
I'll try using a static DNS settings from the router instead of the "let my ISP choose" as I have been having problems possibly related to DNS issues on a wired laptop machine (running Linux as well).
Hooya said:
I have never specifically set up any DNS settings on any device in the house. Not even sure how to see what the settings for that are on the Android devices.
I'll try using a static DNS settings from the router instead of the "let my ISP choose" as I have been having problems possibly related to DNS issues on a wired laptop machine (running Linux as well).
Click to expand...
Click to collapse
Try Google DNS or something
I'm fairly convinced it's not a DNS issue. If it was, rebooting the router would have absolutely no effect at all. But a reboot of the router (unplug and re-plug, a software initiated reboot doesn't seem to work) makes the net fly at great speeds and pings on all devices. For a while. Then it goes bad.
I'm testing a 3rd party app to change the DNS settings to 8.8.8.8 (google) on one android device to see if that one behaves differently. Setting the router to custom DNS settings caused me to get locked out of all internet completely. I couldn't even get into the router software from a wired computer to see the settings anymore. It was like the router didn't exist anymore.
Hooya said:
I'm fairly convinced it's not a DNS issue. If it was, rebooting the router would have absolutely no effect at all. But a reboot of the router (unplug and re-plug, a software initiated reboot doesn't seem to work) makes the net fly at great speeds and pings on all devices. For a while. Then it goes bad.
I'm testing a 3rd party app to change the DNS settings to 8.8.8.8 (google) on one android device to see if that one behaves differently. Setting the router to custom DNS settings caused me to get locked out of all internet completely. I couldn't even get into the router software from a wired computer to see the settings anymore. It was like the router didn't exist anymore.
Click to expand...
Click to collapse
Try setting static IP's for the Mac adresses of the phones in the router and on the phone. Make sure it's outside of DHCP lease boundry of your modem. Sounds like conflicting IPs as already mentioned.
The responders have good intentions but really don't understand the problem entirely. I've faced similar issues.
To quickly dumb down the problem:
Wifi stays connected, but all packets are lost for 10-60 seconds or until wifi is toggled off then on again.
We'll call this Wifi-Connected-No-Connection (WCNC) for the purposes of this thread for easier reading.
Here are my findings...
It may be related to this issue on the google code discussions, there are mentions of complete drop out while remaining connected: https://code.google.com/p/android/issues/detail?id=64706
This has affected both N4 and N5 devices since Jelly Bean. The issue persists in Kitkat but I haven't followed to see if it's entirely been resolved in Lollipop as I refuse to upgrade until certain other issues are worked out with L. If you're good at searching you'll find posts about this drop out issue from a decent time ago.
AP isolation doesn't help.
Modifying most other settings for the router did not help.
What DID help though, is turning the router from N/G mode to B/G mode. I had no WCNC issues with that. Of course, that meant slower speeds, significantly slower speeds. Back on N/G, I find this problem happens pretty frequently.
Packet loss happens at the connection level. Pinging the router means some or all packets are dropped. This is NOT a dns issue.
toastgodsupreme said:
The responders have good intentions but really don't understand the problem entirely. I've faced similar issues.
To quickly dumb down the problem:
Wifi stays connected, but all packets are lost for 10-60 seconds or until wifi is toggled off then on again.
We'll call this Wifi-Connected-No-Connection (WCNC) for the purposes of this thread for easier reading.
Here are my findings...
It may be related to this issue on the google code discussions, there are mentions of complete drop out while remaining connected: https://code.google.com/p/android/issues/detail?id=64706
This has affected both N4 and N5 devices since Jelly Bean. The issue persists in Kitkat but I haven't followed to see if it's entirely been resolved in Lollipop as I refuse to upgrade until certain other issues are worked out with L. If you're good at searching you'll find posts about this drop out issue from a decent time ago.
AP isolation doesn't help.
Modifying most other settings for the router did not help.
What DID help though, is turning the router from N/G mode to B/G mode. I had no WCNC issues with that. Of course, that meant slower speeds, significantly slower speeds. Back on N/G, I find this problem happens pretty frequently.
Packet loss happens at the connection level. Pinging the router means some or all packets are dropped. This is NOT a dns issue.
Click to expand...
Click to collapse
This makes a lot of sense. Wonder why this would happen with one router set to b/g/n and not another set to b/g/n (the a/n settings are only for the 5Ghz band)...