Could someone post the radio files for their XT720 for T-Mobile USA? I think that Cincinnati Bell would work, too. Loading the 2.2 openrecovery blew mine away, and I didn't back them up. Thanks in advance.
you shouldn't need to load any radio files with the 2.2 update. If it's not detecting your network, you may just need to manually enter your APN into settings.
Related
I am an Australian ADP1 user, I installed the radio update on JF's post. And as soon as I did this my could no longer get a data connection. I have been using my G1 data fine for over 3 months no problems. But as soon as the radio update went in, I could no longer get a data connection. The APN settings have remained the same.
The default settings for Telstra (http://telstramobile.custhelp.com/cgi-bin/telstramobile.cfg/php/enduser/std_adp.php?p_faqid=2855) which I had been using is telstra.internet.
However for some reason when I change the APN to the WAP settings
telstra.wap, a data connection can be established. I do not want to be charged the WAP prices, and have been trying to find the original radio image on the ADP1.
Can someone please link me to the original adp1 image?
Or help me able to connect to telstra.internet again?
Thanks for your time.
!edit! forgot to write in...what I really am looking for is the original adp radio.img file.
I'm in the same situation... Anyone have the original radio image to ADP1?
Unless the radio images are different between the tmobile version and the ADP, you can reflash the RC29 firmware with the .nbh file. Afterwards you could update your phones firmware as usual.
I'm not completely sure about this so maybe it would be best to get a second opinion. Can anyone confirm this?
Hey guys I have recently rooted my phone and after many hours and headache I have managed to do so. Onto the task of installing a custom rom (so far I have tried MIUI and Froyomod both found from the milestone development forum) I am losing service and haven't been able to do anything about it. If i perform a data wipe and restore a previous nandroid backup (which is basically stock)I get my service back and all is fine, as soon as a new rom is on there I have no service.
I understand you guys need the most amount of info possible to help me so here it goes. My phone is an unlocked A853 Milestone with bootloader version 90.74. I have downloaded the Telus SBF from (wont let me post link but if you search for milestone sbf in google its the second link). I downloaded the one that is under the 2.1 category, second one since it is mirrored. Is this where i went wrong? Because I now see another subcategory below that reads 2.1(Service version), but how could I have service when I go to stock and not after I flash a rom. I never lost service after flashing SBF before I went on to root and do custom rom. Btw I am on the Bell network but my research tells me Bell and Telus are on the same frequency bands and I see no bell SBF for the Milestone.
When I go back to stock and look under Settings>about phone>firmware configuration version it reads a code, I do not see this firmware configuration anywhere if I flash a custom rom. I have tried to manually set my apn but to no avail.
I have given all the info I know, if any more is required I will do my best to provide it. I really want to experiment with different roms but I obviously need to have service no matter what. Thanks for the help in advance.
Could this be a baseband/radio issue? Could a baseband issue cause absolutely no service or just poor reception? If anyone could lead me in the right direction or point out what they think the issue is, shoot, because I'm out of ideas. Thanks
Bump . What if i try to flash the telus firmware i have on stock which gives me service after installing a new rom? Are these roms in any way made for specific frequencies or service providers?
so I tried typing in *#*#4636#*#* and for signal strength it says -113 dBM 0 asu. This means I'm getting good signal and is not a radio issue correct? When I go to run ping test it says " Ping IpAddr: Fail: IP addr not reachable. Ping hostname is also unreachable, HTTP client test: Fail: IOException. I hate to be bumping this so many times but I'm quite new at this and I need some help
I changed the baseband of my Xoom from GSM/UMTS to USA by a mistake.
No Idea how to reset this to european settings.
The mistake happened using the app "Netzwerk" by Phillipp Mangelow.
Since then there is no chance to get an internet connection.
All settings i can directly access are ok.
The above named app has an error and offers only "USA" as selection of baseband.
Has anyone an idea how to reset this or knows an app which modifies this setting?
Xoom without radio is not even a half xoom
Kind regards,
Willy
Try tiamat new rom, there is a possibility to change it back to EURO mode
Hi,
i use a international version of motorola xoom mz601 in india and have updated to android 3.1 and use the latest baseband n_01.83.35p.
after this update the band changed to USA band 800Mhz? i cannot use any network 2G or 3G and the motorola doesn't show any network operators.
i really want to revert back the settings.now how can i downgrade my baseband and what commands i need to execute also i have tried moving to stock 3.0.1 but no change in baseband.
any apk file that would help me change the band?
thank you.
Please help
If you are rooted, and if you have a previous backup done thru recovery before, just go to recovery, advanced restore and restore system only. It should bring back your baseband.
Sent from my MZ601 using Tapatalk 2
What I did was go back to a stock 3.1 provider firmware. Being in India I used Original rom. I flashed boot, system, data and recovery. At that point the 3g radio still wont work, Let it do the OTA updates to bring it to 3.2.2 and it will start working, I think one of the OTA updates flashes the modem and or bootloader and resets it to the correct band.
I could then go back to a custom rom and it was all good, I make sure I stay away form the band settings in future.
Good Morning,
After flashing the Gingerbread Baseband I no longer am able to register on the network for my provider.
The device is from Rogers but unlocked and being used on the Bell network.
After flashing I realized there may be a different baseband for me to use in Canada (just North of Toronto).
I require some help in locating a Gingerbread baseband that would work or provide me with instructions on how to return to the original baseband.
Any help is appreciated!
Thank you kindly,
- Audi2Audi
Did you set the APN manually? You have to do that.
Hello!
APN in Menu|Settings|Wireless & Networks|Mobile Networks|Access Point Names ?
I have set that to: pda.bell.ca
Is there other steps required though?
Thank you for the response!
apn settings is for internet. phone must tower of sim. may be flashing baseband again will soveit because i am tower getting for my country
If you're wanting to go back to stock froyo first you need to visit here to get your original rom... these will also flash the baseband back too
http://forum.xda-developers.com/showthread.php?t=1246678
or here http://forum.xda-developers.com/showthread.php?t=1155874
then you will need to follow this turtorial in order to flash the stock rom back on (go down to second post that one is in English )
http://forum.xda-developers.com/showthread.php?t=1244490
Although it is a possibility that the BB hasn't flashed correctly, might be worth trying it again... might also be worth trying a froyo rom to see if you get a signal then, because if you do you still have the froyo baseband on...
Simplier to flash stock baseband using kdz tutorial in my signature.
Edit:
But i'm not sure if rogers has the same firmware
adixtra said:
Simplier to flash stock baseband using kdz tutorial in my signature.
Edit:
But i'm not sure if rogers has the same firmware
Click to expand...
Click to collapse
Thanks adixtra i always forget about the tutorial of yours
You can flash a .Bin File for Your P920 or P920H.
Ok, now this is getting bizarre hah.
I reflashed the baseband again and everything went normal as it did before.
This time I searched for networks and selected my provider. After about 5 minutes of the device trying to register on the network an error was received that said it was unable to register on this network.
However, when I got to my home screen I was registered on the network. I tested a voice call and it worked. I have tested data as well.
BUT! This is where it gets even more bizarre...The device cycles from 4 signal bars to 2 signal bars to none to 3G (from H) followed by not being registered on the network. Then a few minutes later (sometimes only after a reboot) it returns to 4 bars and begins the cycle again.
Has anyone seen anything like this before?
Thank you again for your help!
Questions or Problems Should Not Be Posted in the Development Forum
Please Post in the Correct Forums and Read THIS
Moving to General
Yes i have seen this with my install of the baseband file but it will not let me register the 3g or 3g+ let keeps me on full with gsm only its why i flashed mine back using the lg update tool software i put it right back to stock using similar way you flashed the baseband file. PS im on rogers as well
teray0n said:
Yes i have seen this with my install of the baseband file but it will not let me register the 3g or 3g+ let keeps me on full with gsm only its why i flashed mine back using the lg update tool software i put it right back to stock using similar way you flashed the baseband file. PS im on rogers as well
Click to expand...
Click to collapse
Good Evening,
Would you be able to upload the KDZ file from your update?
I am having problems with the LG Phone Recovery indicating that I have the most up to date software and halting the recovery process.
Thank you!
- Audi2Audi
Hello,
I flashed an earlier KDZ which allowed me to use the LG Update tool to restore my stock rom.
Thank you everyone for your help and advice.
- Audi2Audi.
it will tell you that but if you use recovery mode and it will download the file then you will have to unplug the phone from usb hold vol+ power then plug it back into the usb and it should download. like i said i used similiar method to flashing baseband
On my windows 7 not detect omap 4 and i can't flash baseband,what can i do?
Basically i got a xoom 3g a week ago i unlocked, rooted, backed up, and flashed ics. Ive been having trouble with the screen, its does not respond to my touch quite alot of the times, i need to take it back for warranty.
I restored my back up of honeycomb which is where im at now
Im in australia and baught it on a optus 3g plan. Build is h.6.5-17-1 (does not appear on motorola website)
I need to get rid of cwm recovery and replace it with the original boot loader and also lock the device but keep the current build.
Im very new to this and have no idea what im doing, help would be appreciated, please reply as if i was a 5 year old.
Thx
Check the stock files stickied at the top of the General section. You are likely to find what you're looking for there. Those stock image files are usually earlier builds...if you flash the correct one for your device you should be able to update OTA to the build that you had originally. Just make sure that it is the correct one for your device.
If you rooted, you should be able to restore.
thanks. I flashed the Telstra files and it all works, but the problem is im with Optus ( a difgerent Telco) I cant find those roms anywhere.
When I flashed the telstra 3g rom it places the carriers app, and changes settings and bookmarks etc for the carrier.
I need an optus 3g rom to flash, i dont care what version as long as can run ota to bring it up to 3.2 (which is what i purchased it as stock standarD)