hello!
i have a big problem with Active Synch synchronizing..
the story:
yesterday i tryed to change PP to 12MB, but it did not worked.., and my phone freezed (BlackDiamond2.0)
than i did Hard Reset.
after HR it turned on, and then AS tryed to synch, but my phone freezed..
i tryed to put my battery out, but it did not helped
i would like to flash a new rom, but the RUU says: phone not responding..
please help me!
regards,
pulyka
Put the phone into Bootloader mode and flash. Check Wiki, under Wizard section, under troubleshooting / how to unbrick your phone section.
worked!
thanks, it worked perfectly!
pulyka said:
thanks, it worked perfectly!
Click to expand...
Click to collapse
Problem solved so i will lock the thread.
tried to put an image on my device and befor moving the installation gives an error and i found the screen wrote usb from up and v 1.00 from down and nothing happening even after many resets !!!
It is stuck in the bootloader.
Try to upgrade again.
The Wiki will tell you.
Your Uni is most probably fine.
thank you .. your commentsresolved my problem .. i followed the steps in the WIKI
thanks again
try this for dead mobile
try this for dead mobile
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
Try It For Boot Problem.
aymn_louis said:
tried to put an image on my device and befor moving the installation gives an error and i found the screen wrote usb from up and v 1.00 from down and nothing happening even after many resets !!!
Click to expand...
Click to collapse
TRY IT FOR BOOT PROBLEM.
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
Hello Guys,
first i have to say sorry for my bad english...
now my problem:
yesterday i´d successfully rooted my HTC magic with the tutorial from Hayriku.
My Problem now is that i have to send my phone to vodafone and i´d like to set it back to factory defaults and also unroot it.
i searched the forum and found another thread with the original sapphire recovery... so i tried it this way.
i put the img. file on my SD Card and typed in the command for a reboot, but the cmd line says me "not found"
i typed "adb shell reboot" but then it told me "not found"
Now i´ve got a huge problem and hope somebody could help me.
very much thanks in advance
best regards... Dominik
Hi,
Could you post the link to the tutorial please? I've seen differents versions of the same one, so maybe some steps differs)
But, if you have well done the other parts of the tutorial, I presume that you can do an "ugly" reboot... (aka removing the battery and boot it normally).
Hey,
thanks for your answer,
it was the first Tutorial which is in the Haykiru Root thread, here from XDA-Developers.
isnt it the same way to reboot via ADB, or power off and start manually ?
how can i check if my phone is resetted to ne original recovery ?
Many many questions
best regards
Hi there , I was trying to use JuonuputBear to S-OFF my phone through the wire trick , so I was doing the wire trick (after several failing tries) , and somehow the phone was a total brick , doesn't take usb or charge led ... So I looked into this and I found a QHSUSB_DLOAD fix for that , however my phone doesn't even enter or appear as it is in that mode , I tried doing the wire trick while the phone is dead it didn't work , I tried my linux machine the QHSUSB_DLOAD the phone wasn't found ! I guess the bootloader was wiped when Jounuput bear was doing its stuff , plz help me guys !
EDIT : I don't think anymore the bootloader is wiped since I didn't reach the part where it installs JuonuptBear's bootloader ! PLease any ideas !
you should have posted this in the Q&A section. You arent going to get much help here, just people ranting on the fact that you posted a question in the development issue. Mods should probably move this to that section. As for your problem, i can't really help. sorry
thx , I will tell a mod to move my thread :'(
Have you tried using the Sensation unbrick thread?
try unbricking project or ask in juopunutbear's thread
It tells me to use QHSUSB , which isn't working for me , may you plz link me to it so I could ensure ?
seaskyways said:
It tells me to use QHSUSB , which isn't working for me , may you plz link me to it so I could ensure ?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1522351
rzr86 said:
http://forum.xda-developers.com/showthread.php?t=1522351
Click to expand...
Click to collapse
My phone is not being detected , I removed everything , I try to detect , nop ...
seaskyways said:
My phone is not being detected , I removed everything , I try to detect , nop ...
Click to expand...
Click to collapse
while doing the juopunutbear method did you have enough battery?
if not remove battery,sdcard and sim and charge it as it is for 5-6 hours
then put them back and switch on the device normally
I had 99% charge !
seaskyways said:
I had 99% charge !
Click to expand...
Click to collapse
did you check the troubleshoot from the guide you used?
edit:it is better to post your issue also in the thread you used
Troubleshooting in the jounuputbear thread is for live phones , not for dead phones ...
Any help guys ?!?!
seaskyways said:
Any help guys ?!?!
Click to expand...
Click to collapse
the only thing i can tell you is use jtag.
i am out of ideas
Thats what I finally thought about , but I know nothing at all about JTAG , I need professionel help
EDIT : Maybe AdamOutler :?
seaskyways said:
Thats what I finally thought about , but I know nothing at all about JTAG , I need professionel help
EDIT : Maybe AdamOutler :?
Click to expand...
Click to collapse
i never used jtag.i have no experience on it
you can go in a local repair shop.probably they can fix it
I got it to boot !!! I re-ran the joupunut thing , and tried doing the wire-trick before the phone even shows any sign , instantly the PC showed that qhsusb mode , and everything went alrighty !! Maybe this can be an answer for others !
seaskyways said:
I got it to boot !!! I re-ran the joupunut thing , and tried doing the wire-trick before the phone even shows any sign , instantly the PC showed that qhsusb mode , and everything went alrighty !! Maybe this can be an answer for others !
Click to expand...
Click to collapse
troubleshoot
glad for you man
seaskyways said:
I got it to boot !!! I re-ran the joupunut thing , and tried doing the wire-trick before the phone even shows any sign , instantly the PC showed that qhsusb mode , and everything went alrighty !! Maybe this can be an answer for others !
Click to expand...
Click to collapse
Hello, I am having a simliar issue with the Windows driver error coming up when trying to get S-Off after the wire trick. I was able to restore fine, but everytime I am about to get a successful wire trick it gives me the driver error.
Can you tell me what you did? Thank you!
whohitme said:
Hello, I am having a simliar issue with the Windows driver error coming up when trying to get S-Off after the wire trick. I was able to restore fine, but everytime I am about to get a successful wire trick it gives me the driver error.
Can you tell me what you did? Thank you!
Click to expand...
Click to collapse
Please try and use my Guide here http://forum.xda-developers.com/showthread.php?t=2247319 i am very confident if used it will be fine and should let you proceed without any errors
My uncle had a nexus 7(wifi tablet) tablet which he took Malaysia and then gave it to me it had android kitkat(4.4.4) so i updated it to android lollipop(5.2) it was working fine but then i noticed that playstore was not working, it turned on and whenever i tried to download something then it just gets stuck in downloading and after 10 mins it showed app couldn't be downloaded due to error code 495 , so after seeing this i performed a factory reset but still it didnt helped then i downgraded it to android kitkat(4.4.4) but still the problem didnt solved , i tried every possible solution but still the problem didnt solved. plz help me i really need your help. peace out