Related
Hi all,
Trying to update to a WM6 rom, i may have done something wrong...
After formating as described in the guide, I can't communicate with the unit (in the RUU : error 260 update error).
On the bootloader screen, I can read :
"Tornado
IPL 1.00
Tornado
SPL 1.00.0008
Tornado 1U"
I've tried on 2 different XP PC's, no luck.
Any advice you can give to me ?
Thanks.
Load IPL/SPL from SD card ?
Having done a few mor searches :
- On another Tornado I own, I can read IPL & SPL are 2.00x. So my problem should come from them. I may have used a ROM with wrong versions. With this other Tornado, a small "USB" can be seen in the lower left corner of the bootloader. It never appears anymore with the broken one.
- I can flash this other Tornado without problem from the same PC, so the problem may not be on the PC.
- It seems that you can flash directly from the SD card : put a ROM with a specific name and boot. Anybody knows how to do that ? It could be a solution to gain access to my Tornado, and be able to use the usual tools.
Sorry if my questions are a bit stupid, but I'm no more in an area I know... I'm learning the hard way how to deal with all this !
Thanks.
destombes_chris said:
Having done a few mor searches :
- On another Tornado I own, I can read IPL & SPL are 2.00x. So my problem should come from them. I may have used a ROM with wrong versions. With this other Tornado, a small "USB" can be seen in the lower left corner of the bootloader. It never appears anymore with the broken one.
- I can flash this other Tornado without problem from the same PC, so the problem may not be on the PC.
- It seems that you can flash directly from the SD card : put a ROM with a specific name and boot. Anybody knows how to do that ? It could be a solution to gain access to my Tornado, and be able to use the usual tools.
Sorry if my questions are a bit stupid, but I'm no more in an area I know... I'm learning the hard way how to deal with all this !
Thanks.
Click to expand...
Click to collapse
Do a hard reset. I'm quite busy right now but do this: hold both left and right soft key and at the same time press the power on button. Press the zero key when prompted. You may have to try a few times as he timing is important.
Good luck!
try to format BINFS with the mtty or the tera term tool it may work...and then fla**** again
illi said:
Do a hard reset. I'm quite busy right now but do this: hold both left and right soft key and at the same time press the power on button. Press the zero key when prompted. You may have to try a few times as he timing is important.
Good luck!
Click to expand...
Click to collapse
I did it a few times : I'm asked to press the zero key, press it, can see the i-mate screen during 1 second, a white screen during 1 second, and then the bootloader 3 colours...
Profy_X said:
try to format BINFS with the mtty or the tera term tool it may work...and then fla**** again
Click to expand...
Click to collapse
These tools need to communicate between the PC and the phone, and I can't right now.
destombes_chris said:
Hi all,
Trying to update to a WM6 rom, i may have done something wrong...
After formating as described in the guide, I can't communicate with the unit (in the RUU : error 260 update error).
On the bootloader screen, I can read :
"Tornado
IPL 1.00
Tornado
SPL 1.00.0008
Tornado 1U"
I've tried on 2 different XP PC's, no luck.
Any advice you can give to me ?
Thanks.
Click to expand...
Click to collapse
The diff IPL SPL if I'm not wrong, have to do with the RADIO, someone correct me if I am wrong.
destombes_chris said:
Hi all,
Trying to update to a WM6 rom, i may have done something wrong...
After formating as described in the guide, I can't communicate with the unit (in the RUU : error 260 update error).
On the bootloader screen, I can read :
"Tornado
IPL 1.00
Tornado
SPL 1.00.0008
Tornado 1U"
I've tried on 2 different XP PC's, no luck.
Any advice you can give to me ?
Thanks.
Click to expand...
Click to collapse
I have the same exact problem as you! I've flashed my Qtek 8310 with T-Mobile SDA rom (which is compatible...) since then.. My bootloader shows exactly the same as you, and when I plug the USB there is not the "USB" showing on the bottom left...
In addition to that, when I load up normally, it's stays stuck at the first T-Mobile logo screen...
Did you came out with a solution? I've tried Hard Reset too, but it didn't help, on the contrary... Now I'm stuck at bootloader and I do not get even the T-Mobile screen...
sharedworld said:
I have the same exact problem as you! I've flashed my Qtek 8310 with T-Mobile SDA rom (which is compatible...) since then.. My bootloader shows exactly the same as you, and when I plug the USB there is not the "USB" showing on the bottom left...
In addition to that, when I load up normally, it's stays stuck at the first T-Mobile logo screen...
Did you came out with a solution? I've tried Hard Reset too, but it didn't help, on the contrary... Now I'm stuck at bootloader and I do not get even the T-Mobile screen...
Click to expand...
Click to collapse
No, as of now, no luck... but I don't give up !
Hello,
I tried to upgrade my htc universal and in my opinion i seemed to work but when it says it is finished and I need to reboot my universal it is stuck in the usb v1.1 screen even after a reset..
Please help
The solution you seek is readily available in XDA-Wiki:
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
thx worked!!! he's working again!!
Same procedure this moring. First time stuck in bootloader but everything workd well
So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes
noonas said:
So here's the deal, I have a Qtek S200, stuck in tri-color screen.
The screen says IPL 2.10, SPL 2.20.0001.
I have been told that this is a G4 device that was flashed with a G4 IPL.
Any number of flashing tools I use tells me Invalid tool, file open, error etc etc.
It appears that my device is toast.
IS there a way to revive this little beauty>?
Please say yes
Click to expand...
Click to collapse
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.
noonas said:
Anybody? Please? I have read the WIKI, the lazy guides, they all result in the same.
Click to expand...
Click to collapse
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?
noonas said:
Oh and also I was told the Oipro had a solution , but since PM and other ways to contact, no response.
Anyone knows of a way?
Click to expand...
Click to collapse
Not ready to give up on this , please someone please...
puhleeze? Helehehehellp me?!
noonas said:
puhleeze? Helehehehellp me?!
Click to expand...
Click to collapse
Echo,,, echo echo echo.. hello, hello hello....
you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)
marar said:
you can't flash a g3 with g4 upgrader. the program don't allow you to do this..
if your spl / ip is like x.xx.0001 is a g4 if is x.xx.0000 is a g3
you can instal a g3 update on bootloader (the 3 colors screen)
just connect to usb port and start the program/try with novendor update. ( the program not the ms dos)
Click to expand...
Click to collapse
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.
noonas said:
So in Tri-color screen it says the following:
IPL 2.10
SPL 2.20.0001, this should make it a G4 chip then.
On to do the NVID update now...
Ok downloaded the Upgrade_HardSPL_G4 tool and ran it.
It went rather quickly and ended in a completely green screen
att he top it says:
IPL 2.10
SPL 2.20.0001
Will do some more attempts.
Click to expand...
Click to collapse
So I downloaded Prophet Shadow 2.0 rom and ran the G4 upgrade RUU.
During the flashing progress the Bar on the Phone whent RED a couple of times, it eventually went to 100% (being red for about a minute), once the flash completed the phone rebooted in to the sam old tri-color screen again,.
What do to now??
*bricked*
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..
marekPLPH said:
did you try to recover the device yet by flashing a NVID ROM before flashing a cooked rom? try downgrading it first before hardSPL.. let me find links for you to read..
http://forum.xda-developers.com/showthread.php?t=310452
follow this link very very carefully..
Click to expand...
Click to collapse
Downloaded the Prophet's 2.20.7.34_2.20_7114_02.69.21 Rom
Launched the G4 RUU, and I get Error 260 Update Error ;(
/Jonas
*EDIT*
Bad USB Cable (Oups), I flashed the G4 completely (again the progress bar on the phone goes red at times and then green again) once completed it reboots to the same BootSplash (Tri-color) screen without any difference.
/Jonas
did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...
marekPLPH said:
did you tried the other USB ports at the rear end of your CPU??
did you tried the recovery prcedures stated on the files i gave you to read?
if you have followed those there should be no problem bro..
try reading them back again and this time carefully...
and before flashing remove battery.. make sure its charged 50% or more... return battery, do hard reset when its on boot loader try connecting USB make sure you see a USB sign on the lower left of your screen... when RUU starts check the upper right corner of the screen of your phone if theres an RUU sign < optional, its just like a USB sign on the lower left of screen>
your phone should work if all procedures have been done...
Click to expand...
Click to collapse
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.
noonas said:
Well this 'ol PZ I have only have one USB port. I have another PZ but is Vista.
I leave the phone on USB Charge over night so it should have enough juice.
I will go back and re-read the instructions, but this is not my first HTC device... but I may have missed something.
Click to expand...
Click to collapse
Status report.
Downloaded the file as referred to in the post.
Once I run it, it stops at 80% RED bar on the phone.
On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
What now?
goja67 said:
Download Prophet_PV_Temp and you will fiks it.
Click to expand...
Click to collapse
Thanks for the tip, I downloaded this ROM, ran the G4 RUU file.
It went through (again with a red bar at times on the device).
The PC said it all went successfully, and the phone reboots to tri-color screen again, SPL and IPL still the same.. DAMN!!
Any other suggestions or should I just declare it bricked?
If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .
thangkls said:
If your device is G4 , try this RUU:
http://www.mediafire.com/download.php?yjzwtd4yybt
Hope it'll fix your device as it did for mine .
Click to expand...
Click to collapse
About 80% in I get "INAVLID COMMAND"
Hi,
I have the same problem. My imate was G3 ( I learn it after appyling the G4 batch ) I need to recover process and files from G4 to G3. I tried to recover by RUU_Prophet_220734_2207114_024721_NVID.exe (novendor)
But, On the PC (RUU 2.5.2) it says the following:
Error 326: Invalid Command
This NBF file cannot be used for your PDA phone. Please check your NBF file
Do you have any solutiun or idea???
Hi guys...
Well Here's my story....
I was an Universal guy for about 5 years, and now I find myself stuck with a Prophet....
Don't take me wrong, I realy loved my Uni, and the prophet seems a good phone...
So after using it for a few days, I came back to this forum, and entered the prophet world...
Without spending the minimum time needed to search and learn how to properly upgrade the phone, or even tp know if it was a G3 or G4, I downloaded and flashed my prophet with a new ROM...
All went fine, and I got stuck in the bootloader screen, for about an hour... Then I finally found out how to properly HardReset the device, and now....
Well,... now I'm stuck in the splash "Inovation" screen and nomatter what I do, I just can't enter the bootloader....
After readding a bit...yah I know I should have done that before, and not after... I realize that my battery may be the culprit for not entering bootloader and so I plugged it in to the wall charger...NO charging light came on...
I know I don't need to write the next few words, but here they go...
HELP!!! PLEASE!!!
EDIT:
I needed the SIM card in my prophet, so I took it out, and also took the SD card...
Then I decided to re-try entering the bootloader...and....SUCCESS!!!
Now doing the RIGHT procedures to upgrade my prophet...
I have try to flash the unofficial rom. However, the phone rebooted during the update process. Now, my Acer s200 only can display the splash screen and cannot go into windows...
Anyways can flash the rom again?? I tried to use Acer_EUU.exe, but it need to detect the phone by Activesync. Anyways can flash the rom bypass activesync?
Some problem....
Hi!
I tried to flash from original EN ROM version on RU version and had the same problem - the device displayed Windows splash screen and then just reboot. So, I was confused but I didn't stop this process and after half an hour Windows loaded...(during this time I removed he battery and pushed soft-reset button a lotof times).
So, my only advice is to try to wait with re-booting device till the Windows boot and then to flash the original ROM (if you'll find it).
For me - after I loaded RU version of Windows I just flashed for custom EN ROM and it was OK (without this issue).
Good Luck!
It solves your problem..
DimICE said:
Hacked ACER_EUU.exe
Link: http://www.mediafire.com/?wy2yynnjz2z
ActiveSync connection is not needed!
Also is not needed to edit version.txt..
Just replace original ACER_EUU.exe with this file, execute it. Press next,next,ok,ok.. Message "Waiting for download mode coming" appear..
Power your Acer s200 with Power+Camera buttons pressed and connect to computer.
Tested on 2 acer s200 phones
Sorry for my English)))
Click to expand...
Click to collapse
link not working ( http://www.mediafire.com/?wy2yynnjz2z )
http://dimice.ru/ACER_EUU.exe
Rom update can be computer's fault
DimIce's program works perfectly. I've thought I bricked my phone many times, but always have been able to recover. This is what I recently discovered. In the middle of a flash, my computer said "write error". 'Thought my phone would stay dead. Finally, I switched to another computer and flashed the phone with no problem. So if you suffer a bad flash, simply change computers. If none is available, reboot your computer to clear the memory, etc. (by the way I'm using Windows 7 x64) and try again - sometimes even changing the USB port might help. The phone excels in it's ability to be re-flashed -even if you suffer disaster in the middle of a procedure.
As we dedicate only to HTC devices you won´t get too much attention.
Better try here:
http://www.eten-users.eu/
Good luck,
orb3000 said:
As we dedicate only to HTC devices you won´t get too much attention.
Better try here:
http://www.eten-users.eu/
Good luck,
Click to expand...
Click to collapse
Ignore this guy he has a bot setup for posting this on everyone that has 1 post or is posting in general or Upgrading, Modifying and Unlocking, You need to flash a rom based of the 1.00 oem drivers, flash this rom: http://forum.xda-developers.com/showthread.php?t=596304 and all of your problems will be solved, if not let me know and il help you out.
rafyvitto said:
Ignore this guy he has a bot setup for posting this on everyone that has 1 post or is posting in general or Upgrading, Modifying and Unlocking, You need to flash a rom based of the 1.00 oem drivers, flash this rom: http://forum.xda-developers.com/showthread.php?t=596304 and all of your problems will be solved, if not let me know and il help you out.
Click to expand...
Click to collapse
If you have any problem please take it to the council.
my only intention is to let new members know that this is an HTC forum only!
So they don't waste their time
If that bothers you, shame...
XDA has never meant to be HTC only.
Just open your eyes, dear sir.
I have a problem with the installation romu message pops up to me(sorry acer usb host driver must be installed in windows xp sp2 or later version please update os version to windows sp2)
stuck on clean boot screen
Hi, i was updating from EUU_Acer_S200_3.003b.00_EN_03.03.08_3.003.01_20100119 to EUU_Acer_S200_3.003c.00_ES_03.03.08_3.003c.00_20100201 but accidentally closed the acer's application, so the phone is stuck on "clean boot" screen? what should i do?, thank you!
Hi there , I was trying to use JuonuputBear to S-OFF my phone through the wire trick , so I was doing the wire trick (after several failing tries) , and somehow the phone was a total brick , doesn't take usb or charge led ... So I looked into this and I found a QHSUSB_DLOAD fix for that , however my phone doesn't even enter or appear as it is in that mode , I tried doing the wire trick while the phone is dead it didn't work , I tried my linux machine the QHSUSB_DLOAD the phone wasn't found ! I guess the bootloader was wiped when Jounuput bear was doing its stuff , plz help me guys !
EDIT : I don't think anymore the bootloader is wiped since I didn't reach the part where it installs JuonuptBear's bootloader ! PLease any ideas !
you should have posted this in the Q&A section. You arent going to get much help here, just people ranting on the fact that you posted a question in the development issue. Mods should probably move this to that section. As for your problem, i can't really help. sorry
thx , I will tell a mod to move my thread :'(
Have you tried using the Sensation unbrick thread?
try unbricking project or ask in juopunutbear's thread
It tells me to use QHSUSB , which isn't working for me , may you plz link me to it so I could ensure ?
seaskyways said:
It tells me to use QHSUSB , which isn't working for me , may you plz link me to it so I could ensure ?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1522351
rzr86 said:
http://forum.xda-developers.com/showthread.php?t=1522351
Click to expand...
Click to collapse
My phone is not being detected , I removed everything , I try to detect , nop ...
seaskyways said:
My phone is not being detected , I removed everything , I try to detect , nop ...
Click to expand...
Click to collapse
while doing the juopunutbear method did you have enough battery?
if not remove battery,sdcard and sim and charge it as it is for 5-6 hours
then put them back and switch on the device normally
I had 99% charge !
seaskyways said:
I had 99% charge !
Click to expand...
Click to collapse
did you check the troubleshoot from the guide you used?
edit:it is better to post your issue also in the thread you used
Troubleshooting in the jounuputbear thread is for live phones , not for dead phones ...
Any help guys ?!?!
seaskyways said:
Any help guys ?!?!
Click to expand...
Click to collapse
the only thing i can tell you is use jtag.
i am out of ideas
Thats what I finally thought about , but I know nothing at all about JTAG , I need professionel help
EDIT : Maybe AdamOutler :?
seaskyways said:
Thats what I finally thought about , but I know nothing at all about JTAG , I need professionel help
EDIT : Maybe AdamOutler :?
Click to expand...
Click to collapse
i never used jtag.i have no experience on it
you can go in a local repair shop.probably they can fix it
I got it to boot !!! I re-ran the joupunut thing , and tried doing the wire-trick before the phone even shows any sign , instantly the PC showed that qhsusb mode , and everything went alrighty !! Maybe this can be an answer for others !
seaskyways said:
I got it to boot !!! I re-ran the joupunut thing , and tried doing the wire-trick before the phone even shows any sign , instantly the PC showed that qhsusb mode , and everything went alrighty !! Maybe this can be an answer for others !
Click to expand...
Click to collapse
troubleshoot
glad for you man
seaskyways said:
I got it to boot !!! I re-ran the joupunut thing , and tried doing the wire-trick before the phone even shows any sign , instantly the PC showed that qhsusb mode , and everything went alrighty !! Maybe this can be an answer for others !
Click to expand...
Click to collapse
Hello, I am having a simliar issue with the Windows driver error coming up when trying to get S-Off after the wire trick. I was able to restore fine, but everytime I am about to get a successful wire trick it gives me the driver error.
Can you tell me what you did? Thank you!
whohitme said:
Hello, I am having a simliar issue with the Windows driver error coming up when trying to get S-Off after the wire trick. I was able to restore fine, but everytime I am about to get a successful wire trick it gives me the driver error.
Can you tell me what you did? Thank you!
Click to expand...
Click to collapse
Please try and use my Guide here http://forum.xda-developers.com/showthread.php?t=2247319 i am very confident if used it will be fine and should let you proceed without any errors