Related
this is whats going on. one night my screen was letting me select stuff just fine. the next morning i woke up and the screen was unresponsive. now the hardware keys do work just fine. now heres the the bad part. i figured that the issue was originally casued by my CFW so i did a hard reset.... unfortunally that wasnt the problem.i did knotice that when i do tap the screen when the backlight dims down it does brighten up. i donno if that helps. anyone have any ideas. oh and yes it an att phone. no i dont have warranty on it( i got them to upgade my phones that being said the phone went swimming in a hot tub a few months ago)
BUMP~!!!!!!!1
come on anyone have any suggestions???
My digitiser broke a couple of months ago, I had weird oily patterns under the screen that were only visible in some kinds of light (especially flourescent), and reduced sensitivity. Anyway, what I'm trying to say is maybe to check for those oily patterns if you're worried it could be the digitiser. I had to get a replacement on insurance though, so can't be much help with how to fix it.
yah its had an oily square on the screen that if u looked at the right angle ud see it that being said it wasnt to big. also that square was on there for almost 7-8 months and like i said when the digitiser went out it kinda worked the night before and then it stopped working the next morning
Sounds like it could be the digitiser then... If you're good with electronics, you could buy a new digitiser and try to replace it maybe? I'm a bit pants at stuff like that though, so just got a new one.
If you get it fixed, apparently the fault is caused by too much pressure on the screen, so keep it out of jeans pockets
A quick look on ebay shows one for £15 (about 25$ i think), comes with tools (well - a plastic scraper / pry & a t6 or t5 screwdriver) - no instructions with the auction - but if you check the wiki it has a dissasembly guide.
Changing the digitiser isnt for everyone - normally (well i found for my old Kaiser) there are ebay sellers who will supply & fit (for a small fee) the parts, ofc check their rating before you send your phone away! Or google for a repair shop close to home - i would estimate you shouldnt pay more than about $40-50 to have a digitiser supplied & fitted, quite possibly much less, depending on the shop of course.
Hi,
My nexus one screen cracked (after falling from 3 feet high) and I need a replacement for the digitizer. I've found this one on dealextreme but I don't know if it will work properly. Has anyone tried it?
http://www.dealextreme.com/details.dx/sku.40671
I've also got this other option. A little more pricy
http://cgi.ebay.es/GENUINE-HTC-NEXU...ssories_RL&hash=item2eaeddd484#ht_2322wt_1137
by the way, can the "plastic opening tool" be replaced by a guitar pick?
thanks a lot
I can't help you with the digitizer but the guitar pick should work fine, it'll just be more difficult.
josealb said:
Hi,
My nexus one screen cracked (after falling from 3 feet high) and I need a replacement for the digitizer. I've found this one on dealextreme but I don't know if it will work properly. Has anyone tried it?
http://www.dealextreme.com/details.dx/sku.40671
I've also got this other option. A little more pricy
http://cgi.ebay.es/GENUINE-HTC-NEXU...ssories_RL&hash=item2eaeddd484#ht_2322wt_1137
by the way, can the "plastic opening tool" be replaced by a guitar pick?
thanks a lot
Click to expand...
Click to collapse
http://cnn.cn/shop/google-nexus-digitizer-p-8252.html
it would be funny if this one is better than the stock one (ie no multitouch/calibration issues)
I have a hunch they are all the same, but please don't hold me to that.
I got the one from ebay, and it worked find with no calibration issues at all.
Note that this is not an easy swap at all. The way this thing is built is pretty incredible. I found someone who tore one down on youtube, and it was split into something like 30 separate videos, and used them to figure it out. I was so surprised and excited that it still worked when I was done that I nearly dropped it again
Note that the one that I got DID NOT come with adhesive. I had to fabricate my own using scotch double stick tape and a knife, and it wasnt perfect. When I was done it seemed to stick well, but there were a few places I could see the tape sticking out slightly, and I'm sure since the seal wasn't perfect that lint would have eventually worked its way inside.
(I ended up sending it off to HTC for an overheating issue and faulty lock button, and elected for the advance replacement, so I ended up with a shiny new phone minus the battery cover they made me keep)
I wish you luck in the repair, I hope you've got a light touch and some heavy patience.
have you tested that digitizer for the dreadful multitouch issues before sending it to htc?
i would love to replace mine, it's getting on my nerves :/
It's so hit-and-miss,I just bought one replacement in lightake.com,I received it today,and I put it on my digitizer.
I bought one off ebay.. went w/a us seller "wholesalegadgetparts" so i could get it quickly the digitizer works fine
as far as adhesive to hold it to the "black frame" i used a 3M double stick tape (cut into very slim strips) that was fairly thin (if its to thick, it'll pop out beyond the aluminum frame when assembled) also used a drop or two of super glue on the top portion..
what sucked was after i got everything back together, my lcd went bad (guess i was mashing it a bit to hard when getting them to stick to the frame) so I bought one off ebay for around $50, seller was "smartlaptopparts" shipped from cali, so quick turn around, and did appear to be "oem"
screen is beautiful now, overall was very happy w/the purchases
so i dropped my phone just the outer glass broke the lcd is find i was wondering where i can get the cheepest replacement for that i realy dont know what the price goes for but id rather not spend 500 on a retail andriod phone. my upgrade is like 3 months
Report it broken, pay $90 for a replacement through Asurion. Cheaper than $500, y'know?
Sent from my FroyoEris
You need to google for a eris digitizer.
LMGTFY
http://www.google.com/search?hl=en&...fai=CMBq5koWzTNrsN46EygTEha3rCQAAAKoEBU_Q0wbi
i think u can get them for like 40+ dollars off ebay
If you don't mind the long shipping times, you can get a digitizer + the entire housing together for around $60 on ebay. Doesn't seem like a bad deal to me.
#EDIT#
Zombie post . . . sorry about that. Need to remember to look at dates before replying.
Palmbxr said:
so i dropped my phone just the outer glass broke the lcd is find i was wondering where i can get the cheepest replacement for that i realy dont know what the price goes for but id rather not spend 500 on a retail andriod phone. my upgrade is like 3 months
Click to expand...
Click to collapse
I just replace mine, and is wasn't too bad. There is videos on YouTube about how to do it. It took me about an hour, and the part costs about 40 bucks. If you need any help with it, feel free to email me [email protected]
Aaron
you can get one @ 49usd
http://www.htcrepairparts.com/touch-screen-digitizer-for-htc-g5-eris-p-2727.html
Palmbxr said:
so i dropped my phone just the outer glass broke the lcd is find i was wondering where i can get the cheepest replacement for that i realy dont know what the price goes for but id rather not spend 500 on a retail andriod phone. my upgrade is like 3 months
Click to expand...
Click to collapse
I'm going through the same thing. Amazon has some digitizers for about $40. I decided to spend the extra $20 and get this instead
http://www.amazon.com/gp/product/B004F5CEDW
It's the whole casing. I didn't want to bother with stripping the digitzer off the frame which is glued on. With replacing the whole body, you just move the mainboard over and plug everything back in. At least this is my hope. I'll post here again when the thing actually arrives. I ordered it two weeks ago and it probably won't be here until mid March.
Good luck with whatever you decided to go with.
UPDATE. hmmm october was the post date. I guess this guy has long taken care of his problem
Are there any particular tools needed? I swear my other half is on a mission to destroy her phone. It'd be good to know how to do some of the possible DIY stuff.
roscuthiii said:
Are there any particular tools needed? I swear my other half is on a mission to destroy her phone. It'd be good to know how to do some of the possible DIY stuff.
Click to expand...
Click to collapse
There's Youtube videos for disassembly. I haven't watched them myself, but I know they exist, so they probably tell you what tools you need there. From what I remember hearing, just some small torx screwdrivers, or maybe some small phillips, too, but don't quote me on those.
Here is a link to the teardown video I followed.
http://www.youtube.com/watch?v=zHwm-32BI0w
The amazon link in my previous post is what I bought. It was the whole body. There are just screen replacements but I didn't want to mess with that because the digitizer is glued to the front piece. I didn't want to risk warping or breaking the front piece and completely screwing myself over. Anyway, what I bought came with the tools you need to perform the teardown and an extra screwdriver that was not needed.
I am glad I did this. However, it came with it's share of issues.
-The very top of my digitizer does not work. As a result, I can't pull down the notification bar. I can get to it through the menu button but it is annoying.
-I had to move the ear speaker and loudspeaker over. They were glued to some foam which was stuck/glued to the chassis. That foam absorbed the vibration. When my phone rings loud it is nasty because the speaker is bouncing around. I tried to cut some foam myself to replace what was stuck in the old case. It helped but it's not perfect.
-There are some rubber buffers? Isolators? Not sure what their called which also needed to be moved over form the old case.
-It took a month to ship to my house. After discovering these issues, I am kind've stuck with them because it would take a month to send the parts back and another month to get a replacement. By then I'll be due for a new phone.
So that's my experience of replacing the whole case.
Let me know if you have anymore questions.
Thanks for sharing your experience!
My pleasure. Glad to help out.
Sent from my Eris using XDA App
To add to this, because I'm sure there are others out there like me who intend to use their Eris until it gets run over, dropped in lava, drawn, quartered, and defecated upon . . .
I ordered the same replacement housing and digitizer as mentioned above, and had 2 small problems:
The housing I got had a nut in it that came loose, so that one of the corners wasn't able to reassemble properly.
There was something different in the new housing that caused the proximity sensor to function incorrectly.
For #1, I just used some super glue to weld the nut into place. This appears to have worked OK, but I fear that the point is weakened now and I will need to be very gentle if I disassemble the phone again.
For #2, The problem was that the housing was allowing bleed through inside the case from the proximity flasher to the light sensor, which caused the sensor to determine that there was something close to it when in fact there wasn't. I placed a small (oh so small) piece of electrical tape into the housing between where the IR flasher and sensor are located, and the problem was resolved.
If presented with the option of purchasing a new digitizer alone, or a new digitizer and housing together, follow groovel76's suggestion; it's well worth the time and money to go with the latter. The hassle of cleaning the old adhesive off of the new housing, and the risks of getting new adhesive in places where you don't want it far outweigh the cost of just getting a housing with adhesive pre-applied. I tried to do just a digitizer first, and ended up with a small amount of super glue (DO NOT RECOMMEND) getting on the new screen and the edge of the housing, as well as a screen that didn't seat properly because I didn't get quite all of the old bits out of the old housing. This resulted in dust getting under the screen and another crack when I attempted to fix what I'd screwed up the first time.
Between the availability of parts and ROMs for this phone, I see it being in my family for a LONG time yet.
Yes! Buy a digitizer online (most come with the tools you need such as the torx screwdrivers, mine did) and search for videos on youtube. That's what I did and it only cost me $37 for the digitizer and about 30 minutes of my time. And it worked perfectly as new when I got it all back together.
Ive cracked my screen and ive found i can buy a new screen and lcd for 169.99. or i can buy just the over glass for $20. I heard you can use a heat gun to seperate the glass and the lcd. Has anyone done this and can tell me if it works?
Sent from my SGH-I727R using xda app-developers app
Mostly likely the digitizer will get destroyed in the process. Buy the complete unit.
Someone said a few days ago he only replaced the glass but he had to break it in order to separate it, use the search I bet you'll find it quickly. If you can afford it take the whole thing, less chances of screwing up your phone, and you could always keep the old lcd for a test run with a glass only or in case you somehow manage to crack it again.
Still I'd suggest buying a screen protector once you fix your screen, costs less, barely noticeable and saves a whole lot of money and hassle.
kishke said:
Someone said a few days ago he only replaced the glass but he had to break it in order to separate it, use the search I bet you'll find it quickly. If you can afford it take the whole thing, less chances of screwing up your phone, and you could always keep the old lcd for a test run with a glass only or in case you somehow manage to crack it again.
Still I'd suggest buying a screen protector once you fix your screen, costs less, barely noticeable and saves a whole lot of money and hassle.
Click to expand...
Click to collapse
This. I cracked my screen and bought an entire new one for $160 via ebay. It took 10 minutes to take apart and install the new one and be back up and running. I also bought the Otterbox Defender, honestly...works like a charm. It's durable, nice, feels good and it doesn't feel as bulky as it looks. The only down fall about a case with a screen protector is that the Galaxy series has a screen that goes all the way to the edge of the phone (like most modern phones now) so hitting stuff on the VERY edge of the screen is more difficult because of the raised case.
Buy the screen and a protector and if you are still curious, buy the replacement glass for your broken screen and try it. Worst case, you're out 20 bucks and have a completely broken screen (would be out the other $160 for the new screen you'd have to buy if you mess up any way) or best case, you're out $20 bucks but have a new screen incase you ever break it again.
Unscrew the 7 screws on the back (one is above the sim slot, keep it separate as it's a different size) and once you take the back piece off, there's one small black screw holding the board to the screen. The phone is 3 pieces, screen, board and back piece, it's extremely simple. Just pop all the circuit things with your nail or whatever (there's like 6 total). You have to pry your headphone jack off as it's glued unless your new screen comes with one...doubt it.
someone posted they got sammy to replace it for 189, call sammy up and see what they say, i think thats a good price
Forget Glass
OFWGKTADGAF said:
Ive cracked my screen and ive found i can buy a new screen and lcd for 169.99. or i can buy just the over glass for $20. I heard you can use a heat gun to seperate the glass and the lcd. Has anyone done this and can tell me if it works?
Sent from my SGH-I727R using xda app-developers app
Click to expand...
Click to collapse
I repair phones and have replaced Lcd/digi assembly on both I727 and T989. No way you get that apart without busting the exiting assembly up. The cheapest part can be order via Ebay from China and you'll have to wait about two weeks for part. Or there's the company I used in San Fancisco at gounlock dot com that has it listed at $154 I believe. They have a listing on ebay under SkyStarTrade and I offered em $148 including shipping and the took it. I had the part in 3 days. Would highly recommend!!!!!!
I just got off the phone with Sammi Friday. The Rep quoted me $158 to replace the glass. So if they mess up the digitizer is on them. Cheaper than I was able to find the combo anywhere on line. So tomorrow my phone heads back to Sammi. I'll let you know in about three weeks how the service was and whether they honored their quote.
And exactly 8 days from the date that I shipped it to Sammi I have a my phone back. They replaced the LCD, bezel and glass for $158 as quoted. Not only that but they paid all shipping and used UPS 2nd day air both ways. And I'm still under warranty by having them take care of it. All in all couldn't be happier with the service. So if anyone needs the glass fixed my vote would go to Sammi.
Last night I dropped my TF 700 about 5 feet onto concrete floor.
It was working fine right after the drop, but the screen panel ('Gorilla Glass') was popped out a bit and one
corner of the frame was severely dented. But the worst part is that I thought I could fix it on my own.
So I disassembled my TF 700 following the 'TF 700 Teardown Tutorial.' I was able to fix the dented aluminium backplate
(I ripped off the warranty seal during this process though).
After this I reassembled the tablet and everything seemed fine at this point.
However, when I tried to turn it on, the screen display wouldn't turn on. I know that the tablet is still functioning because
when I connect it to my PC, I can see all the files saved. But the screen is completely dead.
I'm pretty sure that this is because I accidently bent some cable component that connects the LCD panel to the mainboard
(the flat cable thing that is made up of copper fibers). Upon closer examination, it looks like the bent cable is preventing some parts from
connecting to each other (please see the picture attached). I really need this tablet and I'm here to ask you what I could do to fix this.
Where should I go and how much do I have to pay to replace/fix the bent cable? Or even better, where can I get the new back-plate? Cuz mine now looks terrible..
Desperately waiting for some advice...
almightytaek said:
Last night I dropped my TF 700 about 5 feet onto concrete floor.
It was working fine right after the drop, but the screen panel ('Gorilla Glass') was popped out a bit and one
corner of the frame was severely dented. But the worst part is that I thought I could fix it on my own.
So I disassembled my TF 700 following the 'TF 700 Teardown Tutorial.' I was able to fix the dented aluminium backplate
(I ripped off the warranty seal during this process though).
After this I reassembled the tablet and everything seemed fine at this point.
However, when I tried to turn it on, the screen display wouldn't turn on. I know that the tablet is still functioning because
when I connect it to my PC, I can see all the files saved. But the screen is completely dead.
I'm pretty sure that this is because I accidently bent some cable component that connects the LCD panel to the mainboard
(the flat cable thing that is made up of copper fibers). Upon closer examination, it looks like the bent cable is preventing some parts from
connecting to each other (please see the picture attached). I really need this tablet and I'm here to ask you what I could do to fix this.
Where should I go and how much do I have to pay to replace/fix the bent cable?
Desperately waiting for some advice...
Click to expand...
Click to collapse
Ouch! Tough break. Unless you have insurance, shed a few tears, bury it quietly in the backyard behind the garage, and buy a new one.
BTrack said:
Ouch! Tough break. Unless you have insurance, shed a few tears, bury it quietly in the backyard behind the garage, and buy a new one.
Click to expand...
Click to collapse
If you do not have an extensive warranty, you'll probably lose about as much money repairing this unit as when you'd buy a new one (it sounds pretty bad, judging from your story). It might be better to bite the bullet, as BTrack proposed.
Hard for me to see what happened by the pics.
Someone had post sometime back that they were parting out their broken Infinity.
Maybe the search can turn up the thread.
Glad I've had a folio around mine.
Banged it a few times being careless.
I feel for ya...hope you can find a fix.
Ouch, unless yo have insurance I think you may be out of luck. I know Asus will fix tablets with " costumer induced damage", but they charge for parts and labor. And it looks like it would cost more to fix than buying a new tablet.
Sent from my ASUS Transformer Pad TF700T using XDA Premium HD app
.Just an off the wall idea, you might try sending a PM to someone who has bricked their device and see if they want to sell it. You might be able to pick up the case and connector that way
I had a drop onto tile with my first prime.
My AMEX covered the cost but they made me send it to Asus (even after getting an estimate) instead of just refunding the money like they had on some previous items. When mine dropped it was just the front glass that cracked all the way across, as well as the aluminum body being deformed. The touchscreen was working, screen worked, device was fully functional. The final repair + shipping came to around $378, and that was still a functional (though sharp, pointy and ugly) device when it got to them. If you bought it on a credit card you should check to see if they have any kind of accidental coverage. Good luck
Well thanx a lot guys..
Thank you for all your help.
I guess I just have to buy new one then..:crying:
almightytaek said:
Thank you for all your help.
I guess I just have to buy new one then..:crying:
Click to expand...
Click to collapse
Why don't you try taking it apart like you initially did, buy a bricked one and try to fix it?
You could sell it to me so I don't have to disassemble a fully working one to play with hardware
I had dropped mine off a table onto a concrete as well. About the distance too. Hit right in the corner of the power button. The glass held up well. The metal bent up and plastic completely cracked through. I was able to squeeze it back together, but was still bent up. It still was functional.
I was did an a-hole move. Since I did it a week after receiving from Amazon, I told them it came damaged, but packaging was fine. They exchanged and not a problem.
You could try exchanging it from where you got it. Another option, there are aftermarket warranty services that you may be to use if you got recent enough. Some allow you to get purchase within thirty days of purchase.
Although, my guess, you probably past that time. I would suggest trying to fix it again. At this point, you have nothing to loose.
Send it back ta Asus for an estimate to repair. Ya never know, you might get off with a cheap fix.....worth a try.
I'm bummed for ya though.
Brad
Sent from my ASUS Transformer Pad TF700T using XDA Premium HD app