I can't belive this hasent been posted here but Klutsh has made the best jailbreak & downgrader for the G1. It supports loading your own payloads from sd card and the ability to downgrade your ps3's.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Direct download G1 32b: http://www.klutsh.com/download/57/
His website: http://www.klutsh.com/
Files needed: http://www.ps3news.com/PS3-Hacks/ps-jailbreak-downgrade-files-leaked-ps3-jig-files-modded-pup/
Downgrade info: http://www.nextgenupdate.com/forums...noob-friendly-psgrade-downgrade-tutorial.html
To install just put it on your sd card make sure its named recovery.img go into terminal emulator type:
su
flash_image recovery /sdcard/recovery.img
reboot recovery
additional info's:
MAKE SURE FLASH DRIVE IS EMPTY, FAT 32, AND IN THE USB SLOT NEAR DISK TRAY add the lvl2diag.self file from the correct directory and the modified PUP to your flash drive.
Put your ps3 into service mode it will automatically turn itself off unplug jailbreak device and plug in the flash drive. Turn ps3 on it will automatically downgrade (TAKES ABOUT 5 MINUTES THEN IT WILL AUTOMATICALLY TURN OFF WHEN DONE). We need to get the PS3 out of service mode just copy the lvl2diag.self file from the correct folder onto your Flash Drive plug it in to your ps3 and turn it on it will automatically be in retail mode.
Keep blueray movies working
1. FIRST ALWAYS Downgrade from 3.50 to 3.41 (Modded PUP)
(Don't get out of Service Mode)
2. Downgrade from 3.41 to 3.15.
3. Update to Retail 3.41 (not modded one) (Get out service mode shut off ps3 completely and boot up normally and update through usb .)
4.Now GTFO of service mode.
How to Access Playstation Recovery Menu
1. Turn off Playstation®3.
2. Hold The power button down; The system will turn on and turn off once again.
3. Once the System has been shutdown, re-press you finger until you hear 2 consecutive beeps
4. When you hear the 2 beeps take finger off power button.
5. You will be promted to plug in your controller via usb and then hit the PS button
6. The Recovery menu will pop up.
Read all instructions everywhere before attempting this I am not responsible for anything you do to any of your devices but I have used this myself multiple times and it works great.
Until it is CERTAIN that entering SERVICE MOOD and/or DOWNGRADING from 3.50 will not disable BluRay DVD Playback on the FAT PS3, I will not do it... I want the bluray movies to always work on it..
But I do really want to downgrade and jailbreak.
Sent from my HTC Dream using XDA App
Can I still play online with the downgrade?????
Can you tell me what payload is good with this and where do i out the payloads. Would you consider this better then psfreedom amon ra v1.3.1?
Sent from my SGH-T959 using XDA App
junior_8791 said:
Can I still play online with the downgrade?????
Click to expand...
Click to collapse
No you can't play online yet. maybe in the future.
Hi, i am using Hermes v3 payload and it's working great.
This has already been posted and discussed in the PSFreedom thread, even Klutsh has posted and talked about it, and I think thats what every one is talking about right now in the PSFreedom thread. I don't think that we need this thread, though its not my decision on whether or not to close this thread.
tearsphere said:
Until it is CERTAIN that entering SERVICE MOOD and/or DOWNGRADING from 3.50 will not disable BluRay DVD Playback on the FAT PS3, I will not do it... I want the bluray movies to always work on it..
But I do really want to downgrade and jailbreak.
Sent from my HTC Dream using XDA App
Click to expand...
Click to collapse
Check out these two images, we now know for certain which PS3's will lose Blu-Ray playback
model numbers
If that list is for real, that would be so nice... How can i find out all the info on my FAT PS3 ???? If i turn my ps3 around, my serial number ends in .... - CECHG01 .... please tell me something good
good stuff! thanks for this!
Does this img allow the use of homebrew packages? I have started getting everything set downgrade from 3.5. I got the img to open factory mode last night. Just want to make sure once I go through all the steps, I can use what I have or will I need other files.
Can anyone tell me whats the latest HERMES for G1 or latest PL3. I am coming from the original enable_psfreedom disable_psfreedom trick. I dont really know all too much about payloads and any help would be appreciated. I already have this as my recovery i just need to learn a little bout payloads.
The stock payload has no peek and poke, so you need to load a blu ray to play your back ups. I haven't bothered with the other options, but from what I read, their are more stable newer payloads that have less chance of crashing during use.....
Sent from my DROID2 using XDA App
gunz.jones said:
The stock payload has no peek and poke, so you need to load a blu ray to play your back ups. I haven't bothered with the other options, but from what I read, their are more stable newer payloads that have less chance of crashing during use.....
Sent from my DROID2 using XDA App
Click to expand...
Click to collapse
Can you tell what their called and where i can find them. I have this installed and i found hermesv4b but its just a file. Its not a bin or hex file so i dont know how to use it.
Hi all Im sort of new to this whole scene but I have a G1 with recovery-PSFreedom-Dream-v1.3.1 on a Fat PS3 3.41 and it works great. But i want the best PL and other things that at are available including downgreading and everything else can some one please tell me what I need. In short I want the Best of the best for my G1 I have been to a post and it has all the PL's (I think)but I dont know whats the newest/best to put on my G1 also are there any other goodies that may be out there that I dont know about for my JB Thx
Sticking with what you have stock on the images is best....you can experiment with payloads. A few sites carry compiled bins and hexes, others will need to be compiled to work. The only thing most are missing is the br patch for playing backups....just need a blu ray booted and then go back to xmb and play the backups.
Sent from my DROID2 using XDA App
Has anyone else tried this? Has the situation changed since the most recent updates? 3.66 etc.?
All you ps3 users!!!! Buy an xbox360 :d
xillius200 said:
All you ps3 users!!!! Buy an xbox360 :d
Click to expand...
Click to collapse
Yes! And then just chip it and worry about getting bricked instead of updated.
or get an nes and play Mario bros
tvall said:
Yes! And then just chip it and worry about getting bricked instead of updated.
or get an nes and play Mario bros
Click to expand...
Click to collapse
LOL
I think I could settle for having a care-free viewing experience on my PS3...let alone 'other facilities'. If I see Cinavia on my PS3 again it's going out the window...
Related
Full drop was not posible.
So made a copy of the System folder.
If you like the work of me & my source, don't forget to help us buying a beer.
Get it while it's hot!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Version:
20090109 Sapphire Asia WWE
DROP OF THE SYSTEM FOLDER:
http://www.xmoo.org/android/htc_sapphire_system.rar
nice- can't wait to see what JF can do with this!! i noticed there is a built in pdf reader too...
0_o
ooooo...I'm excited for this, what the outcome will be.
^-^
PDF Reader?
Interesting, there seems to be a PDF reader in there, and an FTP client. Did you install these on your phone, or were they supplied with it? It'd certainly be nice to have pdf capability in the new cupcake update for the G1...
We may get a taste of cupcake early depending on what JF does with this.
NOTE:I'm tired as crap cause I stayed up for 48 hours but I'm so happy cause of this. Excuse my errors.
I'm gonna be the risk taker here and try to apply this on a G1. I should be able to use my backup from nandroid if anything happens. So all this is the system "partion" as fastboot seems to describe it as? So basicly I have to mount system via recovery and replace it?
otto888 said:
NOTE:I'm tired as crap cause I stayed up for 48 hours but I'm so happy cause of this. Excuse my errors.
I'm gonna be the risk taker here and try to apply this on a G1. I should be able to use my backup from nandroid if anything happens. So all this is the system "partion" as fastboot seems to describe it as? So basicly I have to mount system via recovery and replace it?
Click to expand...
Click to collapse
Keep us updated on how this goes. I'm very interested to see the results.
Gimpeh said:
Keep us updated on how this goes. I'm very interested to see the results.
Click to expand...
Click to collapse
tried to use mv...cant boot into normal anymore...checking if system is changed any
EDIT: Pic shows system...
sethp said:
Interesting, there seems to be a PDF reader in there, and an FTP client. Did you install these on your phone, or were they supplied with it? It'd certainly be nice to have pdf capability in the new cupcake update for the G1...
Click to expand...
Click to collapse
This was all in it.
I may get this to work by making it into an img file(nandroid backup file)...How would I do that....on Windows 7?
EDIT: IDEA! Install the latest cupcake build from andblogs.net and try installing all of this stuff manulaly
Could you just copy say, the PDFReader.apk onto your sdcard and install it from there? Or drop the apk into an update.zip?
I tried to install the PDFreader but it fails due to missing libraries. How do I load this firmware into the emulator so I can mess arround with that one instead?
Crazy idea. Take the latest JFrc33 update and overwrite any file in the update with the magic system files...should atleast boot
Lots of HTC stuff
uherrera said:
I tried to install the PDFreader but it fails due to missing libraries. How do I load this firmware into the emulator so I can mess arround with that one instead?
Click to expand...
Click to collapse
Yeah, to be more precise it's missing all the HTC framework stuff. Doubt you would get away with just adding that stuff to your install:
Package com.htc.pdfreader requires unavailable shared library com.htc.framework; ignoring!
Click to expand...
Click to collapse
Somebody should change the subject to HTC Magic System Folder.
Then more people would go to the thread.
pdf reader, etc
hmm, i tried copying the frameworks into system/framework and then installing the .apk file, but that didn't seem to work. Do additional frameworks need to be registered, i wonder?
dwang said:
Somebody should change the subject to HTC Magic System Folder.
Then more people would go to the thread.
Click to expand...
Click to collapse
Changed to HTC Sapphire/Vodafone Magic
Cause officialy it's from the HTC not Vodafone.
Tried my update idea...boots to recovery...atleast it boots now.
HTC Framework stuff
sethp said:
hmm, i tried copying the frameworks into system/framework and then installing the .apk file, but that didn't seem to work. Do additional frameworks need to be registered, i wonder?
Click to expand...
Click to collapse
Yup. See the bottom of /system/etc/permissions.xml
Thing is, I wouldn't be surprised if the android build this thing expects is newer than your current one, with assorted changes in the API, and if the HTC framework stuff depends on more HTC stuff lower down the stack (I notice there's a "libhtc_ril.so" for instance in /system/lib - not looked into what exactly it contains tho).
As a result it'll probably take a bit more than just dropping things into your current installation. That said, I'd love to play around a bit more if I weren't at work
Stop update your phone using these file. These file is made for Magic, not Dream. It has driver file for Magic, not Dream. Wait for JF and stop doing stupid things.
here is proof. (sorry normal cam is broke so u gotta deal with webcam)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Should work for:
Gogear Connect 3 8gb SA3CNT08
Gogear Connect 3 16gb SA3CNT16 (not tested. may need to edit drivers with proper device ids)
Now there are Pre-Rooted custom roms. look at the bottom of the post for a link to the guide.
this is 32 bit only at the moment
on the official Phillips support forum they stated that the developers wouldn't give out the adb drivers, so i used the method found on hikboys thread to make my own.
Now its an actual guide!
1. Put your Connect 3 into "Debug Mode"
a. From the home screen, press the Menu button below the screen.
b. Tap the Settings option.
c. Choose Applications.
d. Select Development.
e. Check the box for USB Debugging to turn it on.
2. Plug in The USB cable
3. After the drivers install, uninstall them in the device manager
4. refresh the drivers and you will see device that says go gear connect
5. install the ADB driver, linked at the bottom of the page, for the go gear connect in the device manager
6. download the newest copy of super one-click from here
7. open super one-click and change the exploit drop down menu to "zergRush"
8. click on the root button and let it do its thing.
9. click OK on the popup to install busybox.
10. after that it may ask you to verify root, allow it to
11. you are now rooted. do a happy dance.
I Have Figured out how to unbrick and flash this device if you have Messed it up while having root privileges. this method can also be used to install custom roms once some are made. if people need the repair/flash method or wanna work on roms let me know in the comments and i will post the files and guides needed for it.
this guide is by mateo1212
Now there are pre-rooted custom roms check out the guide Here
just figured out updating definantly removes the root but you can use the same method to re root.
processor information for the curious=
800mhz arm v7 Cortex A8
Freescale i.MX51 EVK board
very awesome! i just got this for my son for xmas, root will be awesome. so much bloat on this thing.
going to try rooting now. Thanks again.
**edit** i gave this a try and it worked flawlessly. Very happy to be able to remove all of the bloat that comes with this device.
How do I upgrade driver to adb interface? I've rooted other devices and never saw this instruction before. Thanks
I got it rooted. Thanks so much
What I did is uninstall the original driver that installs when you connect the device. After you uninstall, reconnect it to your pc, use the drivers here to allow for adb.
Sent from my LG-P999 using XDA App
hey. im glad my post is helping you guys. i have some thing i would like input on.
1. im in the process of working on a custom rom for this device, should i continue?
let me know. thanks
also if people with the 16gb version can give me there device ids i can make custom adb drivers for your devices also, because this method will work for your devices
Im actually thinking about purchasing this for myself and was a little skeptical until i saw it can be rooted..whats ur opinions on this device? is it worth it? im one click away from ordering. And id definately be interested in custom roms for this.
this is a pretty cool little device. the only thing i have a problem with is the screen size. its a little small for my fat fingers but in the end you get used to it pretty quick. there is a lot of bloatware on it also but after you root you can get titanium backup and remove alot of it. i personally love the songbird music program they have installed. it is soooo much better than the stock music player. some apps dont show up in market but you can always sideload them(downloading the apks to the pc and copying them over to the sdcard then using a file explorer to install them). in all i think if you dont mind the smaller screen it will be a good buy after you root it.
Yea the screen size is what I'm really worried about I've gotten used to the 4inch screen on my phone...I'm torn between this and the galaxy 4.0
Sent from my LG-P999 using XDA App
yea my gf is going to be getting the galaxy player 4.0 around income tax time. she does not like the fact that my mp3 player does not have a camera..lol from what i have seen the galaxy player 4.0 is pretty easily rooted but there isn't any custom firmware for the us version i have only found custom roms for the uk and korean versions.
right now im working on making a rom thats as close to stock AOSP as i can get that includes root and some other helpful software.
im also going to make a custom themed rom with the Espier Launcher as the default launcher and im going to make it clone ipod as much as possible.
the processor is the freescale imx515 so im going to work on compiling my own custom rom from scratch as the hardware is similar to the evaluation board kit. but thats down the road. the first few roms will be based off of the stock rom
i expect my first rom to be out tonight or tomorow during the day
Drivers
When i uninstall drivers, I'm not able to install the new ABD drivers yet, when i uninstall the drivers, the device goes away. When i scan for changes, it installs the stock one, when ii try to update drivers, it says drivers up to date.... any help please.... Thanks
Windows 7 x64 OS
well first off. according to your post you are running windows 7 x64 and this is only for windows 7 x86. to get it working in x64 i need to finish the drivers and then i dont know if you will need to deal with driver signing issues.
if you are doing it in windows x86 make sure to delete the driver that shows up under "universal serial bus controllers" section it will show up as "USB Mass Storage Device" all you have to do is un plug it and plug it back in to figure out whitch one it is. but i repeat if you are running x64 THIS WILL NOT WORK
Fear not though i will soon be posting a few custom roms that are already rooted.
i have 5 in progress now
1 thru 3 are done i just need to gather up the files and write up the guide
1.the stock rom that comes with the device except its rooted and has a few extra utilitys
2.the stock rom that comes with the device except it is stripped of the bloatware and it is rooted and has a few extra utilitys
3.A close to AOSP rom, or atleast the best i can get, with root and a file browser and only the radio app from the normal rom (even has stock android boot screen)
4. A ROM that makes this device loosely imitate the iPod touch
5. totally themed ROM using launcher pro as the default launcher and it will keep the songbird app for music like the two stock ROMs. it will also have root
Ordered one last night now waiting for it to get here...
Sent from my LG-P999 using XDA App
i am uploading the files for the custom roms now
mateo1212 said:
i am uploading the files for the custom roms now
Click to expand...
Click to collapse
did you upload the roms? i need to root my device and flash a new rom, there is so much bloat ont his thing it's crazy
yea i put a link in the bottom of the original post. you do not have to be rooted to flash the custom firmware.
I got it rooted but For some reason no facebook app on it?
Says not supported once i try to update it after i dl'ed it from Snappz, it does not show up on Android Market? I got the SA3CNT08K/37 *gb Model.
yea there is an issue with the market and such for some apps. i have attached the new facebook apk. copy the facebook apk to you sd card and use root explorer to install the apk.
16 gb
I have a 16GB Let me know how I can help..device id's and such.
Hello,
This ROM is based on Tim6a and www_apad_tv-ibex-Flytouch-3-Firmware-V8.
I started customizing Tim's 6a ROM for my own use, basically since I wanted to see all apps compatible with FT3 on Google Play and I wanted to use ADW Launcher. Now that my customization is complete, I wanted to share it with the xda-developers community
The ROM is built to mimic a Samsung Galaxy GIO device. This device has a much smaller screen but has an ARMv6 processor like the FT3. So all apps downloaded from Google Play should work, and with good performance since it will be the app's QVGA version. Gameloft games also recognize this device, so for example you can download and play Ice Age Village.
Credits go to Tim for his great custom ROM, Apad.tv for firmware-V8, Axlien for the build.prop ideas, chairshot215 for performance tweaks. Thank you guys!
mod edit
I hope you enjoy this release!
Tolga
INSTALLATION:
Unzip the contents of mod edit] to the root folder of your SDcard, and reboot FT3. When the installation is complete, don't forget to take out the SDcard and remove the installation files.
If Wi-fi is grayed out after installation, it means that your wifi card is not 0803 v1. (default) Try enabling old FT3 or 0803 v2 using Tim's scripts in Gscript Lite.
To view all apps on Google Play, follow these steps after installation:
1. Open Google Play, accept the upgrade and accept TOS.
2. Go to Settings>Applications>Manage Applications and select ALL tab.
3. Go to Google Play, clear cache and force stop (DO NOT CLEAR DATA)
4. Go to Google Services framework, clear data and force stop
5. Open Google Play, and you should get a server error. (This is normal)
6. Restart FT3 and all compatible apps should be visible on Google Play!
mod edit
SCREENSHOTS:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
FEATURES:
ADW Launcher (InfoTM Home is also included)
Rooted, superuser
Google Play Store v3.5 (Android Market latest version)
Dolphin Browser, Gmail, Youtube, Terminal Emulator, Root Explorer
Development app for enabling USB debugging
Adobe Flash plug-in 10.1
Tim6a scripts for old FT3 wifi fix, 2MP camera fix etc.
Google Play Store fix and Performance tweaks in build.prop
Minimum apps included for smaller download size and performance
KNOWN ISSUES:
Market fix needs to be applied manually after installation.
TO-DO-LIST:
Custom Kernel to enable HDMI Mirroring and Overclocking (Investigating Stragulus FT Kernel Source atm)
CHANGELOG:
v1.0
Initial Release
Click to expand...
Click to collapse
DISCLAIMER: Please use this mod at your own risk, rooting your device and installing custom ROMs may render your device unusable and VOIDS THE WARRANTY.
I will try to ensure that all info about TolgaMOD_FT3 is up to date here, and will do my best to help in case of problems. It's best to report problems by replying to this thread rather than PM, so that the solution can be viewed by all users.
Hmmm.
I'm useing one of Tim's Roms... not sure wich one. The one where the screen is always dark. I tried dling your fixed stuff put it on my sd card it said it updated took out the sd card than turned it back on, but nothing had changed, everything was still the same? I have tryed the Power button+menu+front button to factory reset it, and still tims rom is still there with no changes. I just am at a loss now... really pissed to be honest. I cant even get the thing back to it's original original settings... I want to use your packet, any suggestions?
Anyone? I have just about tried everything and I'm on my last leg. I'm about ready to just rip the case open and K.O. the battery~
Hi billypaul69,
On my FT3, I just push menu+power to do a factory reset. Perhaps you could try that button combination to do a factory reset.
About flashing my ROM: Apparently the update somehow did not complete for you. I suggest you check out this excellent video tutorial from Axlien to flash a ROM to FT3, and see if it helps: http://www.youtube.com/watch?v=w7xdpnoHLeg
Make sure you don't turn off your device, before you see the following message on the screen:
Updating system firmware completed.
Please shutdown your device and remove the installation card!
Automatic shutdown in 1 minute.
Click to expand...
Click to collapse
If you see any other messages such as "not complete", "wrong system file" etc. and not the one above, please report them here. It's possible that either the .zip file you downloaded got somehow corrupted or the SDcard you are using for the update is faulty. In that case try re-downloading TolgaMOD, or formatting your SDcard and try again.
I hope that my suggestions work for you! Thanks for checking out my ROM!
Regards,
Tolga
Thanks soo much i'm going to try all the steps asap.
\billy
Hi
I just installed your new rom file and everything went Ok. The only problem is that my wifi network is not working. I can activate the wifi but it cannot find any network.
I tried using gscript to install on of the wifi patches but I get the following error message
"stderrermission denide" when I run the script.
Any idea as to why this is happening ? Apart from that, you rom is very snappy in operation.
Hi jammertn,
I'm glad you like the speed of my ROM, that was one of my goals indeed. I'm pretty sure one of the wifi scripts will correct the problem. For example my tablet's wifi works with the "old FT3" fix.
The reason you are getting the "permission denied" error is because gscript was not given superuser permissions.
The first time you run gscript, there should be a pop-up screen from superuser application asking for root rights. You should select "Allow" on this window. If you don't allow it or deny root access, the scripts won't work. If you denied root access and selected "remember" the first time, please launch superuser application from the app drawer and change the status of Gscript Lite to "Allow".
Since you have wifi not grayed out I guess your wifi is 0803 v2. Please try running the "Wifi fix:0803 version2" script and then reboot your tablet.
I hope that helps!
Hi and thanks for the quick reply.
From where do I launch superuser?
Click the middle button (the one with white squares) on the dock, you will have access to all installed apps including superuser.
OK I found the application.
One more question, Something happened and now gscript only sees 3 scripts. How can I make it show all the scripts like before.
Excuse all my dumb questions but I'm new at this.
No problem mate, I think the best way is to simply re-install the ROM You can backup your current apps with Titanium Backup.
Nice, thanks a million
I got it working now.
I'll be watching this thread closely.
Keep up to great work
Yay! I'm glad it worked, c ya around.
Hi Tolga
Is there anyway to activate bluetooth on this tablet? I tried using the gscript but cannnot get is to work. Any ideas ?
Hi jammertn,
This tablet doesn't have a bluetooth chip onboard. Tim's scripts are for driving usb bluetooth dongles. I'm not sure which ones work, but maybe the thread below could have more info.
http://www.apad.tv/apadforum/showthread.php?1358-Flytouch-3-Bluetooth-USB-dongle-testing-thread
Hi Tolga
Thanks for the reply, I have seen that thread but it does not have have any useful info in it. I tried it with an external usb/bluetootyh dongle but still no operation.
Hi,
I ran a quick web search and I haven't seen anyone successfully making a USB bluetooth dongle work on FT3. I think Tim included some kernel modules with the firmware for devs and testing purposes. So please don't assume it will work when you simply plug in any USB BT dongle.
Here's the support thread for Tim6a, there might be more info there:
http://www.apad.tv/apadforum/showthread.php?416-Flytouch-3-Hybrid-ROM-(rooted)&highlight=bluetooth
I think I have a USB BT dongle somewhere, I will take a look if I can find it
Regards,
Tolga
has this been posted on Apad.tv or tested on the iBex Flytouch 3 by people on there?
Do you mean if this ROM has been tested or if USB bluetooth dongle has been tested? I'm pretty sure TolgaMOD runs on Ibex Flytouch 3, since it's basically a modified version of Tim6a.
Here is my ROM's thread on apad.tv:
http://www.apad.tv/apadforum/showthread.php?2675-ROM-06-May-2012-TolgaMOD_FT3_v1.0
i installed rom over Tim 6a rom but still nothing changed,, MENU+power reset also tried.. currently my Huawei data stick does not work since some weeks, thats why i need to install a fresh firmware..
merhaba, yükleme yaptim fakat yine eski tim 6a rom yüklü yani hicbir sey degismedi, hard reset yaptim yine ayni.. ayrica önceden calisan Huawei data stick bi süredir calismiyor, birseyler silinmis olmali diyerek yeni rom yüklemek istiyordum, acaba neden calismiyordur data stick?
Hi people and sorry for coming in your wonderful community with a question.
I was trying to root my Prestigio PMP3270B ICS 4.0.3 android device and now I can not get it to function.
The screen I see in the recovery mode is a broken android image without any options. Picture below:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
In normal mode I get the Touch Screen Calibration, but the touch function does not work....Picture below:
Any ideas as to how I can fix this ???
Thank you
Hi again...
I added some images. You will need to copy paste the links in my above post because I am not allowed to show them here.
Any ideas?
Thank you.
did you try the reset pinhole?
Sent from my GT-S5360 using xda app-developers app
yousef8824 said:
did you try the reset pinhole?
Sent from my GT-S5360 using xda app-developers app
Click to expand...
Click to collapse
Yes, I tried the reset pinhole without results.
If i let the device to boot (second picture link above) and connect usb cable with pc, there are 2 drives that open up in explorer. I can neither access them nor format them.....
I think its time to go for a more expensive tablet like google nexus 7 that will not let me down like this....
the arnova 7h g3 has the same problem go to arctablet fourm sign up and see you there because some one installed cwm recovery and worked
Sent from my GT-S5360 using xda app-developers app
Thanks man but cwm recovery does not work either...
Now my device won't boot at all.... Only the green LED is on when I turn it on.....
Any ideas as to how I install a custom ROM using the SD Card without USB connection?
Because I can not get it to any screen beyond blank.......
Any ideas people?
yousef8824 said:
the arnova 7h g3 has the same problem go to arctablet fourm sign up and see you there because some one installed cwm recovery and worked
Sent from my GT-S5360 using xda app-developers app
Click to expand...
Click to collapse
Yeahh man you got a point here....
Arnova 7h G3 specs are similar to the Prestigio PMP3270B. Logically any ROM will work on both tablets.
http://www.arctablet.com/blog/forum/arnova-7h-g3/backup-original-rom/
Sent from my GT-S5360 using xda app-developers app
I am trying to "burn" that image to SD card so I can use it on my device without the use of USB....
I have tried the "Phoenix Card Tool" but I got error. I couldn't "burn" the image....
Now I am trying a tool called "Win32 Disk Imager"
I will let you know if it works..... I am up to the limit to give up....
I am going to take the device back to the shop pretending that "Oooops.... Suddenly it does not work... Strange"""
Thanks
Athanasis.
UPDATE:
I tried the tool "Win32 Disk Imager" but it does not restart to the SD card when I insert it in tablet and reset. No green rectangle.
Athanasis said:
I am trying to "burn" that image to SD card so I can use it on my device without the use of USB....
I have tried the "Phoenix Card Tool" but I got error. I couldn't "burn" the image....
Now I am trying a tool called "Win32 Disk Imager"
I will let you know if it works..... I am up to the limit to give up....
I am going to take the device back to the shop pretending that "Oooops.... Suddenly it does not work... Strange"""
Thanks
Athanasis.
UPDATE:
I tried the tool "Win32 Disk Imager" but it does not restart to the SD card when I insert it in tablet and reset. No green rectangle.
Click to expand...
Click to collapse
Try with this: http://yf2.value4it.com/Service_Files/TabletPC/PMP3270B/PMP3270B_V1.0.7_20121210.zip
WOWWW... Looks like the real thing !!!
Lets see if you are my Saint Claus.
I am "burning" it on the SD..... In a couple of minutes I will flash the device and let you know......
---------
For any outcome, thank you anyway.....:highfive:
I don't know who you are really, but I want to thank you man..... That file brought my device back to life !!!!
It was the best present I had for this Christmas......Just a minute after midnight !!!!!
Now I will not go to buy another tablet.......... THANK YOU SO MUCH FOR SAVING MY PRECIOUS CASH AND TIME !!!!!!
THANK YOU......................THANK YOU..............................THANK YOU........................................
Athanasis said:
I don't know who you are really, but I want to thank you man..... That file brought my device back to life !!!!
It was the best present I had for this Christmas......Just a minute after midnight !!!!!
Now I will not go to buy another tablet.......... THANK YOU SO MUCH FOR SAVING MY PRECIOUS CASH AND TIME !!!!!!
THANK YOU......................THANK YOU..............................THANK YOU........................................
Click to expand...
Click to collapse
Glad to hear I helped. btw. another surprise... your device IS rooted. Out of the box. Isn't Xmas time magic? Have a good one. :fingers-crossed:
I love christmas.... I have a rooted device... Wooowwww. This is what I was trying to do before the mess..... Now you came here with your magic link to make my life easier... Wooowww....
Come for a beer friend ....... :laugh:
YOU WANT TO SEE MORE ???????
Actually the link you posted was not a rooted ROM but I have managed to unlock it using the following tool and procedure:
Yes guys. I managed to do it. And yes the application that may root this tablet is called "Android ICS Root Unlocker 1.0" Developed by GreekDev -11th July 2012
This is a Zipped file that you will need to unzip.
View attachment 1591923
Make sure that USB is enabled on your tablet and also USB for debugging option is ticked to ON.
Run CMD as an administrator and then write ICS_Root_Unlocker.bat
It is important that you run it from CMD.
At each tablet reboot wait before pressing a key to continue.
Before pressing key to continue enable USB again on your tablet each time it reboots.
If you have problems contact me by quick PM.....
Athanasis said:
Actually the link you posted was not a rooted ROM but I have managed to unlock it using the following tool and procedure:
Click to expand...
Click to collapse
You have to learn a bit more about Android.
It IS rooted out of the box, script just sat qemu property in local.props to already world writable /data partition and copied su binary and SuperSU apk. It did NOT utilize any exploit to escalate privileges. This is the way how devs prefer their devices set up when developing apps that don't require root but want to keep in control of their devices.
Brother, thanks for the info. I am developing in C sharp in visual studio. Also VBA, PHP, MySQL.
To tell u the truth, this is the 1st tablet I ever had....... so you may forgive me for this initial lack of experience.
Sent from my PMP3270B using Tapatalk 2
marlasr said:
You have to learn a bit more about Android.
It IS rooted out of the box, script just sat qemu property in local.props to already world writable /data partition and copied su binary and SuperSU apk. It did NOT utilize any exploit to escalate privileges. This is the way how devs prefer their devices set up when developing apps that don't require root but want to keep in control of their devices.
Click to expand...
Click to collapse
May I ask if the patch I linked above, would root my device if it were with factory firmware.
Sent from my PMP3270B using Tapatalk 2
Athanasis said:
May I ask if the patch I linked above, would root my device if it were with factory firmware.
Click to expand...
Click to collapse
Yes, script would work. You have factory firmware right now, too. Link I've posted is factory firmware.
As for the Android programming you'll need C for DDK and Java for SDK.
Keep in mind embedded programming is quite different from desktop/web programming.
marlasr said:
Yes, script would work. You have factory firmware right now, too. Link I've posted is factory firmware.
As for the Android programming you'll need C for DDK and Java for SDK.
Keep in mind embedded programming is quite different from desktop/web programming.
Click to expand...
Click to collapse
Thank you so much....
Yes I know embedded programming is much more difficult. If I ever decide, I would probably go for the Java platform but not for complicated programs. Free time is quite limited here !!!
Athanasis
:good:
Hi there,
long story short - I do want to root my Bravia tv. I don´t know really why it hasn´t been done by someone already ^^"
In most cases there would be 1000 of questions and threads for this theme, but my internet search didn´t help at all.
Now I am trying to get all information I need to accomplish my task.
-On the tv is android 6.0.1 installed.
-adb connections are useable and i can read write in every folder except the system ones, which I need for the superuser installation
-through adb I could restart into recovery mode, but without TWRP I can´t install the superSU, which I need to get the rights to do all I want with the operating system
For ones I want to accomplish this based on the pure interest in android development. For seconds to use my tv like I want it to
I have 4k files which I can play through an usb 3.0 hdd without stuttering, but when I do the exact same with an wlan (ac) or lan connection I always get stuttering.
The lan port only transmits at 100mbits and I need gigabit lan. I don´t understand either, why the "ac" connection don´t work smoothly as I would expect.
Because I dont want to connect the tv to an usb hdd, but my NAS (Zyxel 520) I searched for other ways to accomplish my task.
On this search I found a forum where a user tried to use a usb 3 to gigabit lan adapter with the RTL8153 chipset, but couldn´t get it working because the tv
needed root rights to activate the device under android. That´s what I am trying to accomplish by this thread.
The link to the mentioned forum thread is: h**ps://community.sony.at/t5/android-tv/wie-gigabit-lan-nachrusten-bei-sony-kdl55w755c/td-p/2256204/page/2"]https://community.sony.at/t5/android-tv/wie-gigabit-lan-nachrusten-bei-sony-kdl55w755c/td-p/2256204/page/2
My skills can be regarded as pro and I am a fast learner. I do work as developer in the java (android) sector. I would appreciate every help, link, suggestions that would make my idea of a rooted android tv
reality and share the results here with everyone else
I hope some people are interested and we can start to get to work
Hi, i've the same TV as you... but didn't thought about rooting it for now...
from what i understand we need an unlocked bootloade first... so basically what you can try is, in an adb reboot in bootloader and then try to unlock the bootloader
fastboot oem unlock
probably this will not work anyway...
I'm trying to work with some friends to create a twrp for a bravia android tv 2015 and try to change it with fastboot
if it's work maybe will be the first sony rooted android?
If not....it's 10 pounds a motherboard on ebay,my luck
see you soon
Any update / help needed?
BTW:this will support all bravia 2015 models?
I'm interested cause would like to remove ads in YouTube (just imagine 3 years old daughter is watching nursery song, any got commercial for grownup...) + auto dschedule to shutdown all radios (I do switch off all radios at home during the night for health reasons. In the end WiFi and mobile is an microwave
M.
wellaflex said:
I'm trying to work with some friends to create a twrp for a bravia android tv 2015
Click to expand...
Click to collapse
I believe this model uses the MT5890 chipset; you would probably like to take a look at this thread then: https://forum.xda-developers.com/android/software/rooting-mediatek-based-linux-smart-tv-t3150281/post68797397#post68797397
And perhaps this kernel is useful: https://github.com/p0isk/linux-3.10.27plus
rolk said:
I believe this model uses the MT5890 chipset; you would probably like to take a look at this thread then: https://forum.xda-developers.com/android/software/rooting-mediatek-based-linux-smart-tv-t3150281/post68797397#post68797397
And perhaps this kernel is useful: https://github.com/p0isk/linux-3.10.27plus
Click to expand...
Click to collapse
Guys, any progress on the case?
I need to root this Bravia Tv
I know nothing about software (only to use what you make).
And I am looking for something to root my Bravia. Why? Because use a 256Gb USB dribe on it, but I can not download things direct to the that USB because say is read only. But I can access to it (write and read) using MLUSB Mounter. But if I try to use any torrent client, can not write directly to the USB. Yes to another USB I formated for the TV, but no for that one. And that one can not be format by the Tv. Maybe because of the size (256Gb). I upgra de SO from Android 7 to Android 8 (Oreo). It is better, but still can not use the USB the way I want.
Some one username:banmeifyouwant rooted their android TV in 2016, but then disappeared, was active elsewhere. Maybe Sony said to cease and desist. Take a look at this post: https://forum.xda-developers.com/showpost.php?p=66311033&postcount=595
wellaflex said:
I'm trying to work with some friends to create a twrp for a bravia android tv 2015 and try to change it with fastboot
if it's work maybe will be the first sony rooted android?
If not....it's 10 pounds a motherboard on ebay,my luck
see you soon
Click to expand...
Click to collapse
any luck doing that?
I would like to root my Sony 49XG9005
I have Xbr-55X850D Bravia running 7.0 . How did you upgrade to Oreo as I couldn't find that on Sony site. Well wanted to root it. Is there a way to hook my comp up to it. I used Remote Adb on my phone and wanted to unlock bootloader . I rebooted into bootloader , the screen then turned gray . I tried fastboot flashing unlock . I then tried fastboot oem unlock . The screen stayed same . I tried fastboot reboot . Then it dawned on me , since I was using IP address , then it might not have connection wirelessly. I tried unplugging tv waiting for a while then plugged in and turned on . The Sony logo pops up then screen goes gray . Think it's stuck in bootloader mode . Is there a way to connect my PC or Android phone with a cable and run Adb ? Oh and did someone make a TWRP for this ? I've downloaded the firmware for the tv and as last resort will try it on USB drive to restore.
~Barahona~ said:
I upgra de SO from Android 7 to Android 8 (Oreo). It is better, but still can not use the USB the way I want.
Click to expand...
Click to collapse
Yes, I'm also very curious how you were able to update your Sony TV to Android 8. Sony seems to have these firmware updates very locked-down. Which model Bravia do you have?
audio_inside said:
Yes, I'm also very curious how you were able to update your Sony TV to Android 8. Sony seems to have these firmware updates very locked-down. Which model Bravia do you have?
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
How to root? I have removed emmc , But no official software update from Sony。
Who has a burning tool for sony TV？
@josonxie you have a message, we have to create a thread, i have the tools for rooting the tv, lets make a try
i've a spare xd9305 too, where the hdmi ports doesn't work anymore.. but everything else is working..
Firmware update to v6.827 (Android 8.0 Oreo)
Android 8.0 Oreo is finally here for Sony 2015/2016 tvs
Firmware update to v6.827 (Android 8.0 Oreo) for Asia Pacific
Release Date: 27-05-2020
https://www.sony-asia.com/electroni..._x94xxc-series/kd-75x9400c/downloads/00016713
I agree with remove ads in YouTube, it is very frustrating
elenaramirez said:
I agree with remove ads in YouTube, it is very frustrating
Click to expand...
Click to collapse
you can install Smart Youtube TV https://smartyoutubetv.github.io/
https://forum.xda-developers.com/android/apps-games/apk-smart-youtube-tv-ads-android-tv-t3949377
futureshock said:
you can install Smart Youtube TV https://smartyoutubetv.github.io/
https://forum.xda-developers.com/android/apps-games/apk-smart-youtube-tv-ads-android-tv-t3949377
Click to expand...
Click to collapse
Or newpipe from fdroid, though sometimes it glitches, but no ads ever again
Anybody can recommend TV launcher w/o ads?
Any news on rooting sony android tv ?
dodo34 said:
Any news on rooting sony android tv ?
Click to expand...
Click to collapse
Same on 2023