Related
Hi,
my Vox was ok with Fireburned Clean WM 6.1 ROM.
I wanted to install the 96 DPI cab taken from
http://allshadow.com/forum/viewtopi...k=t&sd=a&sid=4e574745def746ba36125fd49101481a
I installed correctly following the instructions, and rebooted.
Now, after boot, the following things dont work.
1. File explorer - so i cant go to any folder or delete any files on \windows folder.
2. activesync connection is broken so i cant install a new ROM.
3. recently accessed app list shows blank.
4. my home screen is blank.
The only thing that works is the dialpad where i can make voice calls.
Can anyone tell me how to do a hard reset (any key combination or shortcut??).
Thanks in advance.
I recommend you to uninstall 96 DPI update. To do this, flash your Vox from SD card instead of using ActvieSync connection. How to do this, check Vox Wiki.
Hard Reset Second Way:
Turn off your phone, then press both *SOFT KEYS* and *POWER ON* device. After moment release both soft keys. On the black screen asking for confirmation press *GREEN PHONE BUTTON* and wait couple minutes for phone to initialize.
If you cant make it with this [you must have good timing].. turn off your phone, hold camera button, and plug usb.
the u can run a rom update utility.
akumalol said:
Hard Reset Second Way:
Turn off your phone, then press both *SOFT KEYS* and *POWER ON* device. After moment release both soft keys. On the black screen asking for confirmation press *GREEN PHONE BUTTON* and wait couple minutes for phone to initialize.
If you cant make it with this [you must have good timing].. turn off your phone, hold camera button, and plug usb.
the u can run a rom update utility.
Click to expand...
Click to collapse
i tried trizzos method. but everytime i press camera and plug usb power, the "upload from sd card" screen would come and then just show the bootloader. i formatted twice to FAT32 but still no luck.
Then i followed akumalol's two ways,
the hard reset via soft keys + power key combo didnt work. i tried few times.
But, the second method worked!!!!!!!!!
that is
1. switch off phone
2. hold camera button and plug in usb power cable
3. phone boots to bootloader
4. now use any of the OS drop posted by our Gurus, and execute Flash.exe, it then connects to the phone via activesync and downloads the image.
Thanks very much guys. i will take note of this method as this is my first bricking the phone although the phone came up but no activesync no file explorer.....
Thanks again Trizz and Akumalol.....
Well I tought hardreset would be ur lasta alternative... the method posted by akumalol is the only one i ever used and it works but you have to put ur finger on the softkeys in less than a second after u have powered on the device..this is why some users have no luck with it...u have to be VERY VERY QUICK!
i tried 4 times with no result.. it directly booted to the current OS.
maybe i have poor reflex than you folks..
ahahah no it's a tecnique issue...put your thumbs on the softkeys and with an other free fingers power on the phone... don't tell this to anyone it's a secret tecnique
hahaha. thanks. i will try it when i bust my phone again !!!!.
anyways. thanks for your help.
Hi,
Help needed to restore GSMFSS.NB0 cause flash stops with message,
"GSMFSS at 0x13000000
GSM Doesn't exist
Spin Forever
Use (format All) instead."
Is there a way to format all rom?
Thanx
If you have an original RUU (from either manufacturer or vendor), you could try that and see if you can flash an official rom. First thing would be if you can get into bootloader. If you can't, then I am afraid that you got yourself a pretty expensive paperweight.
However, if you can get into bootloader, there is still hope...
I am sorry but I cannot guide you through the bootloader process for your phone, but I do not own that device. However, this seems to be a way to possibly recover most phones I have seen so far.
Well if press "volume down+Left OK+Reset" i go into this main menu option, with Xand, Nand Format, diagostic,etc but when i press the respective key it does nothing... the GSMFFS error appears when i try to flash from the original RUU. So the device is comunicating, and i can access IPL- insert usb cable...
Can i access the device with rom with P525 Kitchen Tool?
Thnx
santosru said:
Well if press "volume down+Left OK+Reset" i go into this main menu option, with Xand, Nand Format, diagostic,etc but when i press the respective key it does nothing... the GSMFFS error appears when i try to flash from the original RUU. So the device is comunicating, and i can access IPL- insert usb cable...
Can i access the device with rom with P525 Kitchen Tool?
Thnx
Click to expand...
Click to collapse
Well, that is fairly good news... you can apparently access bootloader, so not all hope is lost. As far as the P525 kitchen, you always have to be extremely careful when using a program that was designed to work with a different device from yours.
Have you tried using the RUU after getting the device in bootloader mode? In other words, get it to this status, connect the USB cable to the computer (establish a connection), and then try to use the RUU. It could be that the GSMFFS error could be from the RUU not being able to put the device into bootloader.... It might just work... Good luck!
I got this out of an Asus Russian forum
"Proshivatsya in expert mode, though, and so like to ask
But if you do not return startanet through the expert mode
Hold down, press and hold OK (side button), tyknut stylus reset.
Wait for the appearance of the caption "IPL: Insert USB CABLE"
On the PC run P527FUU.exe, in the back left corner click on the program icon, choose the Expert Mode
Connect the cable and click Update
Do not guarantee the accuracy of keystrokes, but in the manual for the R527 is written that way. "
Here is the link for the site (already google translated)
http://translate.google.com/transla...earch?q=GSMFFS&hl=en&rlz=1C1GGLS_enUS310US310
Browse through some of the posts and see if you can come up with something. From what I have read the "Format All" is accomplished only via "Expert Mode" described above. If you can access that, then you might have a chance to restore the device.
egzthunder1 said:
Have you tried using the RUU after getting the device in bootloader mode? In other words, get it to this status, connect the USB cable to the computer (establish a connection), and then try to use the RUU.
Click to expand...
Click to collapse
Yup, the error appears just 5sec after pressing update button...
I guess the problem resides on the fact that gsmffs.nb0 file is missing from the rom, cause RUU log shows:
ClientDriver.dll Attach
g_Driver=0 g_RTimeout=0 g_WTimeout=0 g_DebugON=0 g_PurgeTx=0 g_PurgeRx=0 g_WaitRx=0 g_splitReadAck=0 g_splitReadAckSize=0
Client_QueueJob(): FeatureID=3, FileName=temp3, HeaderLen=0
Client_QueueJob(): Assumed flashing a Asset Data File because there is no header
Client_QueueJob(): FeatureID=3, FileName=temp2, HeaderLen=0
Client_QueueJob(): Assumed flashing a Asset Data File because there is no header
Client_QueueJob(): FeatureID=17, FileName=temp4, HeaderLen=0
Client_QueueJob(): Assumed flashing a Asset Data File because there is no header
Client_Initialize(): Model=(null), Language=0
Client_Initialize(): Skipping the model verification check
Client_Initialize(): Skipping the language check
Client_Initialize(): rebooting device...
Client_FormatDiskEx(): Type=3 Backup=c:\gsmffs.nb0
OpenComPort(): Wceusbsh
GetWceusbshDevicePreset
OpenComPort(): Wceusbsh \\?\usb#vid_045e&pid_00ce#5&1e9a0cb1&0&1#{25dbce51-6c8f-4a72-8a6d-b54c2b4fc835}
Windows Closing end
OpenComPort(): PC is XP plus
OpenComPort(): PC is XP plus
OpenComPort(): cto.RIT=0 cto.RTM=0 cto.RTC=0
OpenComPort(): cto.WTM=0 cto.WTC=0
OpenComPort(): sucessful
SendFormatDisk() cmd=3
GetEachROMSize(): GSM size=5242880
GetEachROMSize(): OS size=70254592
GetEachROMSize(): EXTROM size=1048576
SendFormatDisk():USBWritePacket
SendFormatDisk(): USBReadPacket
...
And then it hangs on the last command, it should return
SendFormatDisk(): receive format ok
ReadBackup(): Get a packet Remain=65536
...
I assume C:\ is on the pda not my computer right? I guess this file is missing. Very frustating since there's no tools available for my P527...
Look for a Rom dump from this device and see if you can find the missing file.
I think that the C:\ is actually in the computer. Even if the PDA is recognized as external storage, it would probably take a different letter (unless your HDD has a different letter assigned to it). But in bootloader mode, it is not recognized as storage.
Also, look for another RUU (for this device) and see if it works. Good luck
same problem
santosru said:
Well if press "volume down+Left OK+Reset" i go into this main menu option, with Xand, Nand Format, diagostic,etc but when i press the respective key it does nothing... the GSMFFS error appears when i try to flash from the original RUU. So the device is comunicating, and i can access IPL- insert usb cable...
Can i access the device with rom with P525 Kitchen Tool?
Thnx
Click to expand...
Click to collapse
hi santosru,
i am also having same problem were you able to solve it? where you able to select the options?
Ok, this may not work for everyone but it worked for me. I CAN NOT take credit for any of the work. I can how ever offer a very sincere thank you to developers who have brought 6.5 to the P527.
Download SCHIST 21864 from http://forum.xda-developers.com/showthread.php?t=506417
use the P527FUU that is included and check both OS and GSM.
set the OS path to ????/SCHIST_21864_clean\flash.dio.nb0
set the GSM path to ????/SCHIST_21864\EXT GSM(IND)\GSM.dio.nb0
now you need your phone screen to show the IPL: USB Cable message.
turn key lock on, press in on the scroll wheel (left side of phone), press and release the soft reset button with stylus, release the scroll wheel and press the left OK button. it may take a times to get it right but you should get the IPL: screen up. (I actually have to release the scroll wheel then move it down, release and then press the OK button)
insert the usb cable, click the ???? button in P527FUU this should "fix" you.
after it's complete even if phone hangs at the blue Asus screen you can download the correct Asus flash and use the installed included from Asus in advanced mode to restore your phone to WM 6.1 for your area.
if this helps anyone let me know.
IMPORTANT: I just learned that the computer you flash with has something to do with the bad flash. I needed to reflash the original 6.1 back to my phone and it locked up again on my computer, I tried my girl friends and it worked fine using the above steps.
Hello,
I have a big problem and I hope you can help me.
A few weeks ago I want to update my Treo to WM6.5 and use a Rom (I think from navenedrob) which was timebombed (since there I don't know it).
Now I want to update my Treo to the right version from this thead :
http://forum.xda-developers.com/showthread.php?t=541417
but when I start the update with the cheathunlocker tool, it stops at 7%, the usb connection get lost and my Treo make a restart and the old bimebomed version is there...and the tool says, that the file is curuppted and i should check my update tool... but this message comes every time also with other roms.. When I use the method with the media button there comes the colored screen with "serial" and nothing happens.
(The sd card is okay and the same card which I use to install the timebombed version)
What should I do? I can't do anything... Please help me
1. format the card 32fat.
2. do not use hc card.
3. try to download again the rom.
4. if it does not help - try to install 6.0 rom from palm .
Hello
1. format the card 32fat.
2. do not use hc card.
3. try to download again the rom.
I tried this very often... But nothing helps
Where I can get this Rom? On the plam homepage I can't find a Rom, only instructions and a download for Mobile center.
http://rapidshare.com/files/173145556/Treo750_2.23_ROW_WM6.rar
For England (750V) :
http://www.megaupload.com/?d=PS2QHTE6
Oh really thank you for the Roms!
But I have a problem, my Treo dosn't connect to my Pc. When I click to my workplace there isn't a hhd from the Treo.. and the Mobile Center show me, that there i no connection... I have Windows 7, under Windows Vista it don't work too...
Because of that I can't update my Treo.
Do you know the problem and how to solve it?
Really big thank you, this here is a nice community where I get help!!
1. try to install from WINXP - look for another computer...
2. there is a way to get the rom from the file - maybe with winrar- I'm not sure but I remember something like it...
3. look for a rom 6.1 and try to install it from the card.
Okay I try it under Windows Xp, but I get no connection
I get the Rom from the .exe file by 7zip and copy it to the sd card, but the same problem is there at 7%
Do you have maybe am link from Wm6.1?
I think all this dosn't work.. I don't know what the problem is..
What other possibility can I try? There must be a solution for it...
a link to 6.1
http://www.mediafire.com/?4gxsdxh1tmm
maybe you need to replace your card...
Okay thank you.
I try it with an other card and hope it works..
But I think, that this don't work, because when I press the media button und reset, there comes the bootloader with "serial" on the bottom of the display and when I connect it to my pc "usb".. but I can't start the rom with this method...
I try it tomorrow and tell you if it works or not
the "serial" problem happened to me too. It was because bad rom file or bad card.
Okay today I try it with an other Card and 2 Roms (also the orginal Rom), but in the bootloader modus there is every time the "serial" and below..
Palm Tr
IPL-0.20
PalmTr
SPL-0.24.0000
Serial
And when I try it with the cheetahunlocker, it stops at 7% and my Treo make a restart and the old timebombed version is loading..
But maybe my sd card slot is broken from my Treo or the sd card adapter...
because when I run the cheetahunlocker without an sd card, it also stops at 7%...
any idea to check this? Or an other way?
Hey I might have a solution here:
When you format the Mini SD card, do NOT do a quick format. Uncheck that box and do a full format, FAT32, Default Allocation Size.
This took over 15 minutes for me.
Do a scandisk (Right click the drive/tools/scandisk) and check "Fix Errors". This should ensure your SD card is in good shape.
Now copy a good ROM to the card and reset+PTT. The Palm should flash successfully now. If not your ROM may be corrupted.
Hope this helps! It worked for me!
1. Format sd card to fat32
2. find the .nbh file in the stock ROMS
3. rename it CHEEIMG.nbh
4. copy it to the sd (make sure it is not hcsd or it won't work)
5. insert the card in the card reader
6. reset the phone by using the stylus and the reset button next to the card reader, at the same time hold the PTT button on the left side of the phone, (this will put it bootloader mode)
7. when prompted, press the end talk button on the phone, this should start the update process without using activesync.
HardSpl
1. redownload the app and extract using 7zip
2. make sure you have .NET compact framework 3.5 installed on the PC and the phone
3. in CHEETAH unlocker press ctrl+2 and click the header (this will unlock all three options)
4. follow steps
The radio it flashes will not be a good one, so you need to search around to get the right one. Once those steps are complete, you should be able to reflash WM 6.5 without any problems. If you download Navendrob's ROM, you will need to download the arcsoft mms composer to make mms work, and you should be good to go.
Hi backspacepc,
thank you for your help!!!Now it works.. I didn't rename the file. so this was the problem
Hi,
I have a question about this rom. (Wm6.5 from naevendrob)
My touch is broken, so I can't use the touch. Now I have the problem, that I only end a call with touching "end" and not with the normal hang up button on my keybord.
My second problem is, that I can't lock my Treo, because when I want to unlock it, I have to use the touch display.. On Wm 6.1 I could turn my screen with the hang key on my keyboard off.. this is now on this Rom not possible, or do anybody have a solution for this? Maybe in the registry or something?
Thank you
Has nobody a anser?
Speedkazze said:
Has nobody a anser?
Click to expand...
Click to collapse
Since your issue is with the ROM you loaded & your hardware problem, you should bring it up at the specific thread where you downloaded the ROM from.
I would recommend getting the touch screen fixed or roll back to WM6.0.
No it's a Problem with my Treo. I change the touchscreen one time and it works for a while, but after maybe 2 months the touch dosn't work.
Can anybody maybe write a file that i can use the hang up button to hang up without the touchscreen?Or has anyone an idea to change it maybe in the registy or sth. like that?
Speedkazze said:
Okay thank you.
I try it with an other card and hope it works..
But I think, that this don't work, because when I press the media button und reset, there comes the bootloader with "serial" on the bottom of the display and when I connect it to my pc "usb".. but I can't start the rom with this method...
I try it tomorrow and tell you if it works or not
Click to expand...
Click to collapse
Yes I have the same problem, i try with two micro SD card 2 and 1GB formatted to FAT32,and i didnt use quick format, and the cards aren´t HC. but is not working, I supose isnt the card, something is missing,
Please, Can Somebody Help us????
thanks a lot
______________
gracias de antemano
juancamaney69 said:
Yes I have the same problem, i try with two micro SD card 2 and 1GB formatted to FAT32,and i didnt use quick format, and the cards aren´t HC. but is not working, I supose isnt the card, something is missing,
Please, Can Somebody Help us????
thanks a lot
______________
gracias de antemano
Click to expand...
Click to collapse
HardSPL the phone first, then it should work.
i have a problem. my omnia i900 has not working touchscreen and i want to use the second option to control-use my phone with trackpad/mouse but because my touchscreen is not working at all i must change settings to use trackpad instead of touchscreen by remote control(activesync) through computer. how can i do this, can anyone help me.
Install MyMobiler in you pc. It'll allow you to use your PC to control the connected phone.
mymobiler doesnt work for me because when i start my mobiler on computer the phone wants me to accept remote acces and because the touchscreen is not working i cannot accept it. i want to know exactly what program to use AND EXACTLY what to do to change settings on the phone(which file to change or overwrite and with what file to overwrite on phone windows through my computer)
TOUCHSCREEN IS NOT VALID SO I CANT CLICK ON YES OR NO(accept or deny) IN ANY CASE
please write me the exact process
Hey watch the freakin' caps n bold! I'm trying to help here.
Can you access any app? With a simple registry change you can use the trackpad like a mouse pointer... Set the "HKLM\System\State\Samsung\Mouse\ActionMethod" value to "3001" (without quotes).
Else you could do it with Mortscript (do you have it installed?). Just place the script attached in "Windows\Startup" and reboot your phone.
exactly, i cant install any app to phone, because if I want to install it, the phone will ask me to accept/allow the installation, and because touchscreen is not working I cant click on screen to allow installation so the only way to solve my problem is to change registry(to activate mouse/trackpad instead of touchscreen) by connecting computer and phone using activesync on my computer.
I have no experience with registry changing, I even dont know how to find the registry(hklm) and even dont know how to change it so I need exact instruction, but remember, I dont know where it is(reg) and how to change it. So please write me the exact instruction, step by step. Tnx for sending me mouse.zip file. I will use the file when somebody will ive me instruction how to do it.
I know to connect the phone with computer, I know how to use activesync, but to work with registry i am a rookie.
OR
please tell me the exact instruction with mortscript. is it connected with mouse.zip or is mouse.zip standalone script to repair the problem. I dont know how to use mortscript, I did what u wrote- I copy morthscript into phone windows/startup. at the same point i extracted mouse.zip into windows/startup. so both are in startup folder. please give me a little bit more detailed instrution about this. tnx
You know I just fired up my old i910 and with windows button I was able to enable mouse without touching the screen. Swipe dpad to get to settings navigate and enable.
good day.
I don't think he'll be able to send the "Ok" to the window...
Ok I've adapted it again...
Extract the files from mouse2.zip. Place "fix.lnk" in the startup folder and place the other two files on the root of the device (internal memory... not storage or memory card). Reboot the device.
hi.
I'v got loox n560 that was upgraded to WM6.1-6.5 servel times without any problem.
the last time i did update, i did it accidentally with a bad firmware file(uncompleted download).since then, the device wont boot(just a white screen).and the pc wont recognize it.
any way to save it? or i made myself a nice paper weight?
thanks.
I think there was a way to put the N560 in bootloader mode by pushing some keys and soft-reset hole manually (the "monkey grip" it was called or something similar...) and with the file of the rom to be flashed in a SD card... perhaps you can google for information on this ancient -and more unsure that the cable one- flashing mode. Worth to try it better than have a paperweight...
Good luck!
I give you more information (shame that FIRSTLOOX information is not there anymore)
For manual bootloader mode: press On-Off button + left side button (voice recording) + stylus soft reset (for some seconds). Keep pressed On-Off and recording untill the dolphins appear.
I can't find references to flash from SD card. Anyway, for incomplete flashing, Newplowe gives this procedure:
"You should close process "wcescomm.exe" on PC in task manager. Then hold button record, power and puch reset after that you will come in boot loader. Run the program mtty.1.42 and select usb connect. If You will see the any error just start again mtty. Put command l c:\os_213u.nbf (You should put correct flash file in c:\ or use correct path to os_213u.nbf, l - like L but small). When it will done You should start PocketLOOX5xxFlashTool.exe and flash you PDA."
I got this reference from "http://forum.xda-developers.com/showthread.php?t=429148&highlight=flash+n560+card".
Good luck anyway.
this is very interesting...
i was able to put the device into boot loader mode and ran the command "L c:\os_213u.nbf" ("l" didnt work, but L did).
it did something to the device, a progress bar till the end of the screen.but the device didnt reboot.when i try to run POCKETFLASH program it couldnt connect to the device.
i runing windows 7, so i guess it the problem(ACTIVE SYNC is a XP PROGRAM).
i'll try installing XP on another computer and try this again.
thansks.
almost...
i have installed Windows XP just for this, and everything seems to go well, i connect with MTTY, put the l c:\os_213u.nbf command and the device respond.
the next stage i to flash with PocketLOOXN560FlashTool.
when i start it, i receive connection error, and then i go to recovery mode.the program try to communicate with the device, but i get at the end error that the ROM language is different than the language on the device.it says "(ENGLISH)" and there are also empty
()
Click to expand...
Click to collapse
at the end.
i doubled checked this with the original WM5 English rom, and its the same.
is there a way to change the language with MTTY?
any other ideas? its a shame to stop now after i can get a response from the device...
thanks.
The only idea I have is to check if after the failed flashing your N560 is still an "english" one. Perhaps the defective rom has changed the language of your device to something else...
If your device respond to communication with the XP computer, perhaps you could make a rom dump (in newplowe's page you can got tools for doing that) and check in the dump file with an hex editor which language actually has. You can always check newplowe's blog and forum (with google translator ), or ask him
Sorry i didnt post an update.
i have fixed the rom language.it had a gibberish mark at the end of the ENGLISH, after i have fixed that, .the device was flashed correctly and its working!
thanks for thelp guys