Hi,
my Vox was ok with Fireburned Clean WM 6.1 ROM.
I wanted to install the 96 DPI cab taken from
http://allshadow.com/forum/viewtopi...k=t&sd=a&sid=4e574745def746ba36125fd49101481a
I installed correctly following the instructions, and rebooted.
Now, after boot, the following things dont work.
1. File explorer - so i cant go to any folder or delete any files on \windows folder.
2. activesync connection is broken so i cant install a new ROM.
3. recently accessed app list shows blank.
4. my home screen is blank.
The only thing that works is the dialpad where i can make voice calls.
Can anyone tell me how to do a hard reset (any key combination or shortcut??).
Thanks in advance.
I recommend you to uninstall 96 DPI update. To do this, flash your Vox from SD card instead of using ActvieSync connection. How to do this, check Vox Wiki.
Hard Reset Second Way:
Turn off your phone, then press both *SOFT KEYS* and *POWER ON* device. After moment release both soft keys. On the black screen asking for confirmation press *GREEN PHONE BUTTON* and wait couple minutes for phone to initialize.
If you cant make it with this [you must have good timing].. turn off your phone, hold camera button, and plug usb.
the u can run a rom update utility.
akumalol said:
Hard Reset Second Way:
Turn off your phone, then press both *SOFT KEYS* and *POWER ON* device. After moment release both soft keys. On the black screen asking for confirmation press *GREEN PHONE BUTTON* and wait couple minutes for phone to initialize.
If you cant make it with this [you must have good timing].. turn off your phone, hold camera button, and plug usb.
the u can run a rom update utility.
Click to expand...
Click to collapse
i tried trizzos method. but everytime i press camera and plug usb power, the "upload from sd card" screen would come and then just show the bootloader. i formatted twice to FAT32 but still no luck.
Then i followed akumalol's two ways,
the hard reset via soft keys + power key combo didnt work. i tried few times.
But, the second method worked!!!!!!!!!
that is
1. switch off phone
2. hold camera button and plug in usb power cable
3. phone boots to bootloader
4. now use any of the OS drop posted by our Gurus, and execute Flash.exe, it then connects to the phone via activesync and downloads the image.
Thanks very much guys. i will take note of this method as this is my first bricking the phone although the phone came up but no activesync no file explorer.....
Thanks again Trizz and Akumalol.....
Well I tought hardreset would be ur lasta alternative... the method posted by akumalol is the only one i ever used and it works but you have to put ur finger on the softkeys in less than a second after u have powered on the device..this is why some users have no luck with it...u have to be VERY VERY QUICK!
i tried 4 times with no result.. it directly booted to the current OS.
maybe i have poor reflex than you folks..
ahahah no it's a tecnique issue...put your thumbs on the softkeys and with an other free fingers power on the phone... don't tell this to anyone it's a secret tecnique
hahaha. thanks. i will try it when i bust my phone again !!!!.
anyways. thanks for your help.
Related
Hi,
Help needed to restore GSMFSS.NB0 cause flash stops with message,
"GSMFSS at 0x13000000
GSM Doesn't exist
Spin Forever
Use (format All) instead."
Is there a way to format all rom?
Thanx
If you have an original RUU (from either manufacturer or vendor), you could try that and see if you can flash an official rom. First thing would be if you can get into bootloader. If you can't, then I am afraid that you got yourself a pretty expensive paperweight.
However, if you can get into bootloader, there is still hope...
I am sorry but I cannot guide you through the bootloader process for your phone, but I do not own that device. However, this seems to be a way to possibly recover most phones I have seen so far.
Well if press "volume down+Left OK+Reset" i go into this main menu option, with Xand, Nand Format, diagostic,etc but when i press the respective key it does nothing... the GSMFFS error appears when i try to flash from the original RUU. So the device is comunicating, and i can access IPL- insert usb cable...
Can i access the device with rom with P525 Kitchen Tool?
Thnx
santosru said:
Well if press "volume down+Left OK+Reset" i go into this main menu option, with Xand, Nand Format, diagostic,etc but when i press the respective key it does nothing... the GSMFFS error appears when i try to flash from the original RUU. So the device is comunicating, and i can access IPL- insert usb cable...
Can i access the device with rom with P525 Kitchen Tool?
Thnx
Click to expand...
Click to collapse
Well, that is fairly good news... you can apparently access bootloader, so not all hope is lost. As far as the P525 kitchen, you always have to be extremely careful when using a program that was designed to work with a different device from yours.
Have you tried using the RUU after getting the device in bootloader mode? In other words, get it to this status, connect the USB cable to the computer (establish a connection), and then try to use the RUU. It could be that the GSMFFS error could be from the RUU not being able to put the device into bootloader.... It might just work... Good luck!
I got this out of an Asus Russian forum
"Proshivatsya in expert mode, though, and so like to ask
But if you do not return startanet through the expert mode
Hold down, press and hold OK (side button), tyknut stylus reset.
Wait for the appearance of the caption "IPL: Insert USB CABLE"
On the PC run P527FUU.exe, in the back left corner click on the program icon, choose the Expert Mode
Connect the cable and click Update
Do not guarantee the accuracy of keystrokes, but in the manual for the R527 is written that way. "
Here is the link for the site (already google translated)
http://translate.google.com/transla...earch?q=GSMFFS&hl=en&rlz=1C1GGLS_enUS310US310
Browse through some of the posts and see if you can come up with something. From what I have read the "Format All" is accomplished only via "Expert Mode" described above. If you can access that, then you might have a chance to restore the device.
egzthunder1 said:
Have you tried using the RUU after getting the device in bootloader mode? In other words, get it to this status, connect the USB cable to the computer (establish a connection), and then try to use the RUU.
Click to expand...
Click to collapse
Yup, the error appears just 5sec after pressing update button...
I guess the problem resides on the fact that gsmffs.nb0 file is missing from the rom, cause RUU log shows:
ClientDriver.dll Attach
g_Driver=0 g_RTimeout=0 g_WTimeout=0 g_DebugON=0 g_PurgeTx=0 g_PurgeRx=0 g_WaitRx=0 g_splitReadAck=0 g_splitReadAckSize=0
Client_QueueJob(): FeatureID=3, FileName=temp3, HeaderLen=0
Client_QueueJob(): Assumed flashing a Asset Data File because there is no header
Client_QueueJob(): FeatureID=3, FileName=temp2, HeaderLen=0
Client_QueueJob(): Assumed flashing a Asset Data File because there is no header
Client_QueueJob(): FeatureID=17, FileName=temp4, HeaderLen=0
Client_QueueJob(): Assumed flashing a Asset Data File because there is no header
Client_Initialize(): Model=(null), Language=0
Client_Initialize(): Skipping the model verification check
Client_Initialize(): Skipping the language check
Client_Initialize(): rebooting device...
Client_FormatDiskEx(): Type=3 Backup=c:\gsmffs.nb0
OpenComPort(): Wceusbsh
GetWceusbshDevicePreset
OpenComPort(): Wceusbsh \\?\usb#vid_045e&pid_00ce#5&1e9a0cb1&0&1#{25dbce51-6c8f-4a72-8a6d-b54c2b4fc835}
Windows Closing end
OpenComPort(): PC is XP plus
OpenComPort(): PC is XP plus
OpenComPort(): cto.RIT=0 cto.RTM=0 cto.RTC=0
OpenComPort(): cto.WTM=0 cto.WTC=0
OpenComPort(): sucessful
SendFormatDisk() cmd=3
GetEachROMSize(): GSM size=5242880
GetEachROMSize(): OS size=70254592
GetEachROMSize(): EXTROM size=1048576
SendFormatDisk():USBWritePacket
SendFormatDisk(): USBReadPacket
...
And then it hangs on the last command, it should return
SendFormatDisk(): receive format ok
ReadBackup(): Get a packet Remain=65536
...
I assume C:\ is on the pda not my computer right? I guess this file is missing. Very frustating since there's no tools available for my P527...
Look for a Rom dump from this device and see if you can find the missing file.
I think that the C:\ is actually in the computer. Even if the PDA is recognized as external storage, it would probably take a different letter (unless your HDD has a different letter assigned to it). But in bootloader mode, it is not recognized as storage.
Also, look for another RUU (for this device) and see if it works. Good luck
same problem
santosru said:
Well if press "volume down+Left OK+Reset" i go into this main menu option, with Xand, Nand Format, diagostic,etc but when i press the respective key it does nothing... the GSMFFS error appears when i try to flash from the original RUU. So the device is comunicating, and i can access IPL- insert usb cable...
Can i access the device with rom with P525 Kitchen Tool?
Thnx
Click to expand...
Click to collapse
hi santosru,
i am also having same problem were you able to solve it? where you able to select the options?
Ok, this may not work for everyone but it worked for me. I CAN NOT take credit for any of the work. I can how ever offer a very sincere thank you to developers who have brought 6.5 to the P527.
Download SCHIST 21864 from http://forum.xda-developers.com/showthread.php?t=506417
use the P527FUU that is included and check both OS and GSM.
set the OS path to ????/SCHIST_21864_clean\flash.dio.nb0
set the GSM path to ????/SCHIST_21864\EXT GSM(IND)\GSM.dio.nb0
now you need your phone screen to show the IPL: USB Cable message.
turn key lock on, press in on the scroll wheel (left side of phone), press and release the soft reset button with stylus, release the scroll wheel and press the left OK button. it may take a times to get it right but you should get the IPL: screen up. (I actually have to release the scroll wheel then move it down, release and then press the OK button)
insert the usb cable, click the ???? button in P527FUU this should "fix" you.
after it's complete even if phone hangs at the blue Asus screen you can download the correct Asus flash and use the installed included from Asus in advanced mode to restore your phone to WM 6.1 for your area.
if this helps anyone let me know.
IMPORTANT: I just learned that the computer you flash with has something to do with the bad flash. I needed to reflash the original 6.1 back to my phone and it locked up again on my computer, I tried my girl friends and it worked fine using the above steps.
Hello,
I upgraded my Kaiser 130 from Wm6 to Wm6.1 forseveral times, but at the end I restored Wm6.0, because I have never been pleased about Wm6.1.
Whenever I tried WM6.1, My device got freezed, or touch screen sensitivity decreased while in use, so I had to tap screen firmly sometimes.
I had HardSPL v1.0, is this the cause forsuch freezings or other problems? Should I flash higher HardSpls? Please help in this subject..
I want to use Wm6.1. But, after flashing My rom to Wm6.1, I restore back to Wm6.0..
Thanks in advance..
Best Regards.
Is not there any expert to help me?
what is my problem? why can't I get the best performance for Wm6.1 with my kaiser..
Still waiting for a logical reply,
aren't there any expert? Rom cookers?
Thanks in advance..
If you followed the noobs guide to flash to a T & then found the ROM you wanted and read the chef notes, then read fixes etc, should be fine.
Please be patient, i probably would have posted more if you was not bumping the way you are.....
lol good reasoning stylez
I would recommend upgrading your HardSPL, like this:
a. Download the Kaiser-HardSPL-3.29.zip from here and
extract them to a folder on your computer, for example: HardSPL.
b. Now download this file and
extract it to a folder on your computer, for example: JumpSPL.
c. Open the folder you extracted it to, and copy "kaiser_JumpSPL_pof_v1.nb"
and "JumpSPL.exe" (no quotes) to your device.
d. Power down your device, take out your SIM and SD card (if one),
then power back on the device. If it opens an emergency call screen
once restarting, just click the red End key button on your device to
exit and go to the today screen.
e. Open File Explorer, then open JumpSPL.exe on your device, then enter in: "0x00000000" no quotes, and then select kaiser_JumpSPL_pof_v1.nb
f. Now, if done correctly, you should be at a Tri-color screen and
it should say "USB".
g. Now disable USB connections in Activesync/Windows Mobile Device
Center. To do this, click on settings under Activesync or Windows
Mobile Device Center (depending on if you're running Vista or XP) and
UNcheck "Allow USB connections"
h. Unplug your device, wait 5-20 seconds, then plug your device back in.
i. Remember that folder that you extracted the SPL to? Well, on your
computer, open that folder, then run KaiserCustomRUU.exe.
j. Click Next, Next, then Update. Wait for it to finish, then click Finish.
k. Congratulations! If done correctly, you should have HardSPL flashed
on your device. To confirm this, press and hold the camera button on your
device all the way while pushing the stylus into the reset hole. You should
be at a tri-clor screen (called the bootloader). The second line down should
say "SPL-versionhere.Hard" (no quotes). If it does, you're ready to flash!
If it doesn't, please re-read all instructions.
good luck
mbarvian said:
lol good reasoning stylez
I would recommend upgrading your HardSPL, like this:
a. Download the Kaiser-HardSPL-3.29.zip from here and
extract them to a folder on your computer, for example: HardSPL.
b. Now download this file and
extract it to a folder on your computer, for example: JumpSPL.
c. Open the folder you extracted it to, and copy "kaiser_JumpSPL_pof_v1.nb"
and "JumpSPL.exe" (no quotes) to your device.
d. Power down your device, take out your SIM and SD card (if one),
then power back on the device. If it opens an emergency call screen
once restarting, just click the red End key button on your device to
exit and go to the today screen.
e. Open File Explorer, then open JumpSPL.exe on your device, then enter in: "0x00000000" no quotes, and then select kaiser_JumpSPL_pof_v1.nb
f. Now, if done correctly, you should be at a Tri-color screen and
it should say "USB".
g. Now disable USB connections in Activesync/Windows Mobile Device
Center. To do this, click on settings under Activesync or Windows
Mobile Device Center (depending on if you're running Vista or XP) and
UNcheck "Allow USB connections"
h. Unplug your device, wait 5-20 seconds, then plug your device back in.
i. Remember that folder that you extracted the SPL to? Well, on your
computer, open that folder, then run KaiserCustomRUU.exe.
j. Click Next, Next, then Update. Wait for it to finish, then click Finish.
k. Congratulations! If done correctly, you should have HardSPL flashed
on your device. To confirm this, press and hold the camera button on your
device all the way while pushing the stylus into the reset hole. You should
be at a tri-clor screen (called the bootloader). The second line down should
say "SPL-versionhere.Hard" (no quotes). If it does, you're ready to flash!
If it doesn't, please re-read all instructions.
good luck
Click to expand...
Click to collapse
Thank you mbarvian I flashed my Hard SPL, And checked it by pushing Reset&Camera button, it is 3.29.
So can you say that this is the most important cause of the freezings or decreasings in touch screen sensitivity in WM6.1? If I flash Wm6.1 rom, do these problems appear?
Thanks in advance.
stylez said:
If you followed the noobs guide to flash to a T & then found the ROM you wanted and read the chef notes, then read fixes etc, should be fine.
Please be patient, i probably would have posted more if you was not bumping the way you are.....
Click to expand...
Click to collapse
Thank you expert, but I say that, I got such problems even if I flash my device with official Wm6.1 ROMs..
Thanks again..
TO UNLOCK LATEST VERSION OF SPV
HERE IS A SIMPLE GUIDE
FIRST HARD RESET SPV PHONE
TO DO THIS(SWITCH OFF PHONE>HOLD BOTH SOFT KEYS SITUATED UNDER NEITH LCD. AND THAN KEEP PRESSING THEM PRESS POWER BUTTON FOR 2 SECONDS.IT WILL SHOW ON SCREEN PRESS "0" TO COMPLETE NOW RELEASE KEYS AND PRESS "0"
IT WILL HARD RESET AND PHONE WILL TAKE SOME TIME TO COME ON AND MAY BE IT WILL ASK AGAIN TO RESTART SO DO SO.
AFTER HARD RESET
1. INSTALL ACTIVE SYNC VERSION 4.5.0 WORKS FOR ME
2. CONNECT PHONE TO COMPUTER WITH A V3 CABLE.
IF SOFTWARE ASKS CONNECT AS GUEST.
3. COPY FILE ATTACHED WITH THIS POST SP_AllowCertificate
IN UR PHONE WITH ACTIVE SYNC
JUST SAY IN MY DOCUMENTS>MY MUSIC
4. GO IN PHONE FILE MANAGER MY DOCUMENTS>MY MUSIC AND FROM THERE RUN SP_AllowCertificate
IT WILL INSTALL IT. JUST FOLLOW ON SCREEN INSTRUCTIONS.
5. NOW SECOND FILE. EXTRACT ON DESKTOP OF UR PC/LAPTOP
WHICH IS SDA_ApplicationUnlock
6. NOW RUN IT FROM PC/LAPTOP
IT WILL ASK U TO CLICK ON UNLOCK.
DO SO
7. NOW EXTRACT
SPV-Services
AND RUN SPV SERVICES
MAKE SURE KEEP PHONE CONNECTED WITH PC SYNC DURING ALL PROCEDURE AND KEEP INTERNET CONNECTED.
8. IN SPV SERVICES
CLICK SIM TOOLS
THAN IT WILL ASK TO TYPE "AGREE"
AND THAN UNLOCK IN NEXT SCREEN.
AND ALL DONE.
http://www.4shared.com/file/121050994/36527335/SP_AllowCertificate.html
http://www.4shared.com/file/121051000/5790508f/SPV-Services.html
http://www.4shared.com/file/121051011/398c5158/SDA_ApplicationUnlock.html
SPV SERVICES not working any others way to unlock c600
pls help
why not use the search function of the forum and read a few posts?
You could find this one:
http://forum.xda-developers.com/showthread.php?p=2456333#post2456333
hi.
I'v got loox n560 that was upgraded to WM6.1-6.5 servel times without any problem.
the last time i did update, i did it accidentally with a bad firmware file(uncompleted download).since then, the device wont boot(just a white screen).and the pc wont recognize it.
any way to save it? or i made myself a nice paper weight?
thanks.
I think there was a way to put the N560 in bootloader mode by pushing some keys and soft-reset hole manually (the "monkey grip" it was called or something similar...) and with the file of the rom to be flashed in a SD card... perhaps you can google for information on this ancient -and more unsure that the cable one- flashing mode. Worth to try it better than have a paperweight...
Good luck!
I give you more information (shame that FIRSTLOOX information is not there anymore)
For manual bootloader mode: press On-Off button + left side button (voice recording) + stylus soft reset (for some seconds). Keep pressed On-Off and recording untill the dolphins appear.
I can't find references to flash from SD card. Anyway, for incomplete flashing, Newplowe gives this procedure:
"You should close process "wcescomm.exe" on PC in task manager. Then hold button record, power and puch reset after that you will come in boot loader. Run the program mtty.1.42 and select usb connect. If You will see the any error just start again mtty. Put command l c:\os_213u.nbf (You should put correct flash file in c:\ or use correct path to os_213u.nbf, l - like L but small). When it will done You should start PocketLOOX5xxFlashTool.exe and flash you PDA."
I got this reference from "http://forum.xda-developers.com/showthread.php?t=429148&highlight=flash+n560+card".
Good luck anyway.
this is very interesting...
i was able to put the device into boot loader mode and ran the command "L c:\os_213u.nbf" ("l" didnt work, but L did).
it did something to the device, a progress bar till the end of the screen.but the device didnt reboot.when i try to run POCKETFLASH program it couldnt connect to the device.
i runing windows 7, so i guess it the problem(ACTIVE SYNC is a XP PROGRAM).
i'll try installing XP on another computer and try this again.
thansks.
almost...
i have installed Windows XP just for this, and everything seems to go well, i connect with MTTY, put the l c:\os_213u.nbf command and the device respond.
the next stage i to flash with PocketLOOXN560FlashTool.
when i start it, i receive connection error, and then i go to recovery mode.the program try to communicate with the device, but i get at the end error that the ROM language is different than the language on the device.it says "(ENGLISH)" and there are also empty
()
Click to expand...
Click to collapse
at the end.
i doubled checked this with the original WM5 English rom, and its the same.
is there a way to change the language with MTTY?
any other ideas? its a shame to stop now after i can get a response from the device...
thanks.
The only idea I have is to check if after the failed flashing your N560 is still an "english" one. Perhaps the defective rom has changed the language of your device to something else...
If your device respond to communication with the XP computer, perhaps you could make a rom dump (in newplowe's page you can got tools for doing that) and check in the dump file with an hex editor which language actually has. You can always check newplowe's blog and forum (with google translator ), or ask him
Sorry i didnt post an update.
i have fixed the rom language.it had a gibberish mark at the end of the ENGLISH, after i have fixed that, .the device was flashed correctly and its working!
thanks for thelp guys
Hello,
I installed a Windows ROM on my HTC touch pro, wich automatically loads the haret.exe to start android. But my battery is just running out of energy too fast, so I want to go back to Windows.
How do I do this?
If I take my SD-card out, it gives the error that there is no haret.exe.
And I can't synchronize witch my laptop in this status, so I can't change the Win ROM.
Is there somebody who can help me?
Bye,
Joran
tha_joran said:
Hello,
I installed a Windows ROM on my HTC touch pro, wich automatically loads the haret.exe to start android. But my battery is just running out of energy too fast, so I want to go back to Windows.
How do I do this?
If I take my SD-card out, it gives the error that there is no haret.exe.
And I can't synchronize witch my laptop in this status, so I can't change the Win ROM.
Is there somebody who can help me?
Bye,
Joran
Click to expand...
Click to collapse
You can find all the information you need by searching first.
Anyway, try this.
Press and hold the down volume button and soft reset with the stylus. This should take you to the bootloader screen.
I'm not sure whether this will let you connect to Activesync so that you can flash a WM Rom.
However, if you have a Rom that you want, do this:
1/. Copy the ".nbh file" to your SDCard.
2/. Make sure it is named "RAPHIMG".
3/. Place it in the root directory.
4/. Press and hold the down volume button and soft reset with the stylus.
5/. Follow the on-screen instructions.
6/. Once this has completed, soft reset using the stylus.
Good Luck.