Hello. I have a big problem with my HTC Vox, I hope you can help me.
Yesterday I tried to install a new rom on my device. I followed every step, all worked fine. When installing has finished and the device has restarted, appeared a problem. The phone has blocked on the loading process. I can't turn off , the phone doesn't read data cable. I don't know what to do.
I attached a picture to see exactly what i whant to say.
The first boot of a ROM usually takes long as initial setup tasks are executed. Check in the relevant ROM thread if there is anything to take care about.
If even after 15 minutes nothing happens, then try a hard-reset. Switch off (take out battery if needed). Then press and keep holding down both softkeys (L+R) while switching on the device - keep the L+R keys pushed. When the query comes for reset, press the green key.
If you don't succeed, then go back to the original ROM with the standard files from Orange.
Thank you very much. I solved the problem.
And how did you solve it? It may help others with the same problem.
I access boot-loader (Press and hold “Camera + Power” button simultaneously then release the power button first after hold for about 1 seconds, and then the device will enter boot-loader mode.) and then i installed a new rom. I was very simply but for me lasted more to realize how to enter in the boot-loader.
Yes - but this works only with the shipped ROMs - and it will only work for the original one that matches your CID. There is no free CID-Unlock for the VOX, only a CID-bypass with usually a RAM loaded SPL. For that you need to have the OS running to get the SPL loaded there. USPL batchfiles + tools are used for this.
Did you "Hard-SPL" the device first? This means to put the "CID-bypassing" SPL into the ROM? This way you can load any ROM on the VOX in any state of the device (OS up or bootloader).
Related
I attempted to upgrade my Orange SPV M500 (HTC Magician).
The tool failed, and did not install anything.
However, my phone has remained stuck on the "Bootloader", displaying a white screen with "serial" if it's not plugged into the Pc, or "USB" when it is.
I've tried different reset techniques, having the battery out for long periods.
My phone booted up once, then silly me I tried the same tool again, and am back stuck!!
I bet it's something simple to press to get it to boot normal - but I just can't see it.
Please help. I know I'm in the right place to ask.
Paul.
Bootloader
you can try camera + record + reset button to get it out off boot loader mode
if it doesn't work you have to flash it
If this doesn't work, just download the correct rom, and run the update program, this will hopefully sort the problem out if pressing the buttons doesn't work.
hope this helps
Mark
I used the rom cooking kitchen to make some of my favorite roms even better. Basically I just deleated some of the programs I dont use and deleated some of the extra sounds. Everything went through without any problems and now after I flashed it the smart mobility screen comes up and shows the radio and other info but then freezes there. How can I fix this or go back to a different rom? HELP. Thanks again
hollywood said:
I used the rom cooking kitchen to make some of my favorite roms even better. Basically I just deleated some of the programs I dont use and deleated some of the extra sounds. Everything went through without any problems and now after I flashed it the smart mobility screen comes up and shows the radio and other info but then freezes there. How can I fix this or go back to a different rom? HELP. Thanks again
Click to expand...
Click to collapse
try and get the ship rom that came with ya phone i had the same prob with a o2 xda/mda wizard i got the rom whitch was 1.05 ok now
hope this helps
How can I install it, my usb wont connect to the device?
hollywood said:
How can I install it, my usb wont connect to the device?
Click to expand...
Click to collapse
read the hard spl manual
*MICROSD FLASHING*
***IMPORTANT***
Please make sure you have HardSPL on your device.
1. Get a 128MB MicroSD card (or whatever size you like) and format it (***please make sure you format it, but not just delete all contents on it)
2. find the ROM image you would like to use, normally namede RUU_Sign.nbh, and rename it to "KAISIMG.nbh"
3. Plug the card into the phone, then enter boot loader mode by pressing down the Power and Camera buttons simultaneously, and using the stylus at the same time to press the RESET button at the left side. Continue pressing the two buttons for a few seconds after pressing and releasing the reset button until the bootloader screen appears. (taken from Wiki)
4. You will first see a tri-color screen then the information on the card. Press power button to start flashing.
5. After all these are done, press the reset button located at the bottom of the phone to reset the device.
Thank you very much, back to normal!
So i just flashed my vox with dr.gonzo's new 1.0 rom...and I did it the same way i've been doing it for months now (since his first rom 0.1) and it all went good, but when it was suppose to reboot turned off but never turned back on....I turn it on manually and i see the htc logo, it vibrates and then black screen... nothing happens afterwards...please dont tell me its bricked...please.....
If you're not able to get it into the bootloader to run an RUU then I suggest that you flash a signed HTC ROM, flash USPL and then re-flash New Guava v1.0
how do i flash a signed htc rom? when i turn it on, the htc logo comes on, then vibrates, and then a black screen.... when i try a hard reset, it asks me to confirm by pressing send. i press send (correct me if i'm wrong, send is the green 'phone' button right?) and it loads up the htc logo, vibrates and then shuts off. I've never had a bricked phone before, this all just doens't make sense i did the same steps that i've always done.
Seriously? Your phone is not bricked.
If you've flash a ROM before, it's the exact same procedure - what you can try and do is load into the bootloader by holding the camera button and plugging in a USB cable, it will start into the tri-color screen and should show USB is connected then you can flash a signed HTC ROM.
If the ROM is corrupt, this is your best way of "recovering" your phone, if the ROM was flashed properly, after getting into the bootloader, run ruurun 0 and ResetDevice to boot it back into OS.
oh ok, i haven't tried that yet (bootloader mode that is). Now you say i do this by plugging the usb and holding the power button and camera button? is that how it works? h4waii, you just lightened up my day by giving me some hope!
That is how you can enter the boot loader.
1). Turn off and unplug the Vox from external power/USB cable
2). Press and hold the camera button
3). Insert external power/USB cable
4). Continue to hold camera button until you enter the tri-color screen
At this point, you should have a "USB" text label on the bottom left hand side indicating USB is detected - you can then run an RUU from a signed HTC ROM to update it.
press and hold the camera button alone? i tried that, it doesn't power up the unit though?
Yes it does. Hold camera and plug in your USB cable (making sure it's also plugged into your computer).
ok i got it to the triband screen, but when i ran dr.gonzo's rom it got to 3% and said its corrupt. so i'm gonna do what you said and flash a signed htc rom. hopefully it works....
Yes, 3% because SPL is not patched to allow an unsigned ROM to be loaded, flash an HTC ROM to it, once that is complete you can run USPL to re-flash New Guava.
It will work, don't need to hope
you are a godsend! literally have no idea how depressed i was yesterday! being a university student money is very tight right now so was a total shock when i realized i bricked my $350 phone....I wish i had money cause i'd send you some for being so helpful but I dont... So just please understand i REALLLY appreciate your help, thank you.
That's what we're here for. Glad to be of service.
AFTER UNLOCK NO VOICE OR SPEAKER WORKING I JUST FLASHED WITH
(RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27.04.15_Test) NOW PHONE DOESNT
POWER UP OR BOOT MODE BLANK SCREEN
I TRY TO CONNECT TO THE COMPUTER ASKING DRIVER (DATE INTERFACE)
I NEED YOUR HELP TO GET BACK LIVE
PLEASE
THANKS
How did you unlock it? Did you CID unlock? HardSPL version? Can you get to the bootloader by holding down the camera button and power button and soft reset at the same time?
From the sound of things you loaded a CID locked rom onto your locked phone. This is only a guess though based on the fact that the ROM you loaded included a compatible radio.
Just a tip, next time don't use all caps. It's considered shouting and inappropriate. We understand your urge to get it fixed so we'll help even without the caps
Answering Alibaba0101's questions will help a lot. Also, have you tried taking the battery out and putting it back in?
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
lxa786 said:
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
Click to expand...
Click to collapse
I don't see the step where you flashed your original radio back after doing the SIM unlock. The radio that you is a special "patched" radio, and the phone will not successfully boot into Windows with it flashed.
Go into the bootloader (hold Camera during power on), and flash a compatible radio. If you haven't flashed a cooked ROM yet, then just hit up the Kaiser Wiki and grab the original ship radio for your phone.
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
austinsnyc said:
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
Click to expand...
Click to collapse
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Boot Loader
Same here I just hold down camera button and soft reset works every time.
hi I need your more help how can I get phone on boot mode phone dead not responding I tried more then 10 time by pressing camera and power button phone still blank screen.
No display show so how can I flash the phone
Any idea to flash the phone dead mode?
thanks
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
This has gotten people in the past, so sorry if it sounds dumb.
The Camera button has two settings Full Press and Half Press. Press until it stops then press again. You need to be pushing the Camera Button down all the way to get into Bootloader.
Also I never need to press the power Power Button As well.
I may be wrong but, when the phone is on, you can press the Camera and Soft Reset buttons. When the phone is off, you press the Power, Camera, and Soft Reset buttons to go directly into boot loader.
i tried but screen still blank no light nothing when i put usb into the phone asking driver (data interface)?
Can not go in bootloader help?
Tytn 2 is dead .
Ok last night I try to install the new hyperdragon III BlackStone rom everything is fine untill it finish and it cant load in to window, the computer keep asking me for the data interface and the tilt keep restart and the screen only shows hyperdragen III. I was running hyperdragon III opal (10/11/08) I tried MMTY and reinstall the OE rom but no luck, please help!!
Tytn2 Dead or not??
Tytn 2 is dead if you see data interface driver when put in usb cabel install v3 motorola driver and you will see data qualcomm usb driver i device manager .... this mean that totaly erased memory in tytn2 and its dead,only with jtag can flash again.
Please, tell me how can y do it. I have the same problem....
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Click to expand...
Click to collapse
I don't see any step about using the white screen fix so I'm guessing you didn't successfully install HardSPL and then after that you tried flashing a ROM whilst being oblivious to the fact that Hard SPL wasn't installed, so you most likely bricked your phone
AllTheWay said:
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Click to expand...
Click to collapse
Dead HTC KAISER
Hello My friends
After along search and Googling on the net without finding any solution. at last I did took a Risk to solve and save my DEAD HTC KAISER . what i did is I ressembled the HTC KAISER , to see if my USB data input was defect, but it was Good, now .......he he.. what i fond avery smal Batterie planted on the motherboard , i took it of the the board , end waited 1 hour . then i place it back , assembeled my HTC KAISER back
Taaaaraaaaa my HTC KAISER Power Led went ON ,,, YES ..Friends . is charging .
after 1/2 hour , I swish the HTC on ,,,, heeeee Is working......flash it with the new ROM wm 6.5 ...really it went Perfect.. end My HTC KAISER... ALIVE AGAIN.
Greatins , and hoppe this will Help you..........Good Luck .
on youtube you can find videos how to dissembele your HATC KAISER.
thanks to XDA-Developers , for this great Forum.
ericc191 said:
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
Click to expand...
Click to collapse
my kaiser boots up but after the att thing the screen gos black do you know how to fix this
Dear all,
I have two big problems!
1st on is that my phone HD2 won`t start. It just freeze on the white screen with HTC logo and ROM numbers.
2nd is that when I tried to put it in bootloader mode it won`t go. I tried to press down volume key and power key but it happen`s teh same like in the 1st paragraf.
Can you maybe help me???
Thanks in advance.
take the battery out and do a hard reset. Hold volume up and down at the same time and press power button.
I also tried to do that and nothing happens! It just show`s white screen with htc logo.
My HD2 won't go to bootloader tri color screen when I press and hold the VOLUME DOWN then Press and hold the POWER button, but the phone starts normaly.
I already flashed the HSPL3 and nothing wrong happened. But when I tried to check if the HSPL status, the bootloader don't work.
My HD2 is T-Mobile
rsimiao said:
My HD2 won't go to bootloader tri color screen when I press and hold the VOLUME DOWN then Press and hold the POWER button, but the phone starts normaly.
I already flashed the HSPL3 and nothing wrong happened. But when I tried to check if the HSPL status, the bootloader don't work.
My HD2 is T-Mobile
Click to expand...
Click to collapse
Rsimiao, any luck getting your phone into bootloader mode? I have the same problem.
Have same problem
my hd2 won t go in bootlaoder mode, impossible to see spl and wont be flash by hspl 3
impossible to hard reset it
its saying that sd card fail to copy something
is there a solution ??
no usb loading in bootlaoder
Hi I have problem with loading usb in bootlaoder mode.....
When I turn on the phone everything is ok working fine
I'm trying to put a new Rom but I cant because can not find usb
can anyone help me please.....
Dont go to Bootloader (Tricolor Menu)
Hello HD2 Experts,
yesterday i wanted to reboot my HTC HD2 with Android (SD) on it, and after this it hanging on the HTC logo and cant boot.
It goes only to the MAGLDR but not to the Bootloader ( Tricolor Menu) if i press VOLUME DOWN AND POWER...
I installed via USB FLasher on MAGLDR the Windows 7 Phone and it was working perfectly without problems (Just Wlan/Wifi dont working). After this i tried to install 5 different NAND Android on my HD2 and every of this is hanging on this HTC Logo!!! I am sure that all this 5 were working before this...
My Problems:
1. Cant install (NAND) Android.
2. Cant join to the BOOTLOADER (Tricolor).
3. On WIndows 7 PHone no WLAN working.
I'm done with the nerves!!! Can anybody help me?
Best Regards, Mike
Take bettery out, then try again
it will work
i tried EVERYTHING! but it dont help
and battery too!
Having the same problem I have SPL-3.03 HSPL & trying to downgrade to SPL 1.66 but won't go into Bootloader. I've tried an 8gb, 4gb & now 1gb card the file has been renamed in the root to LEOIMG.nbh but just get the tri colour screen. Pressing reset button & holding end call & Vol down button.
This is the right file to rename from HTC?
_HTC HD2_RUU_Leo_HTC_WWE_1.66.405.2_Radio_Signed_15.30.50.07U_2.06.51.07_Ship
Make sure you are not using the USB cable while trying to enter bootloder. I had the same problem, but once unplugged the cable all was fine.
I'm having a similar problem. I reflashed to the HSPL, no problem. I then used the Rom UPdate Utility, which claimed it had updated my ROM to version 2 (although it took a fraction of the 10 minutes, it said it would). When I now try to boot the phone to install the rest, doesn't matter how much I hold the power key (which I presume is the 'make call' key, as that powers the phone up), it refuses to do anything other than boot to the O2 Welcome screen. I'm noticing the replies aren't very helpful here. Is this what I can expect for the whole forum? As a newbie, I can't make posts on the developers forums, so I can't ask them if they've come across this before. It seems a bit pants, to be honest!
HTC HD2 won`t go in to bootloader mode
Junks666 said:
... now 1gb card the file has been renamed in the root to LEOIMG.nbh but just get the tri colour screen.
_HTC HD2_RUU_Leo_HTC_WWE_1.66.405.2_Radio_Signed_15.30.50.07U_2.06.51.07_Ship
Click to expand...
Click to collapse
Hi Junks,
The THREE COLOUR SCREEN is BOATLOADER this is FIRST BOOT LOADER or (I Think) the name is H-BOOT. You have to correct ROM for HTC HD2, but CMIIW the rom is for HTC HD2 T8585 (WWE) with 516 Internal Memory. Is your HD2 this Model or another Model famous with name TMOUS (T-Mobile Edition) with 1024 Internal Memory. I believed if you still have tricolor screen easier to "wake up" your phone.
Im haveing the same problems please someone help... a Demonoid invite code is all I have to offer here
DJ Legless said:
I'm having a similar problem. I reflashed to the HSPL, no problem. I then used the Rom UPdate Utility, which claimed it had updated my ROM to version 2 (although it took a fraction of the 10 minutes, it said it would). When I now try to boot the phone to install the rest, doesn't matter how much I hold the power key (which I presume is the 'make call' key, as that powers the phone up), it refuses to do anything other than boot to the O2 Welcome screen. I'm noticing the replies aren't very helpful here. Is this what I can expect for the whole forum? As a newbie, I can't make posts on the developers forums, so I can't ask them if they've come across this before. It seems a bit pants, to be honest!
Click to expand...
Click to collapse
Is your problem solved ? Hold power key (Red) (Hang Up key) and Volume Down key simultaneously. what is you see on the screen ? if its three color RGB ... you are safe. I will advise whats next.
cheers up
x1123 said:
Is your problem solved ? Hold power key (Red) (Hang Up key) and Volume Down key simultaneously. what is you see on the screen ? if its three color RGB ... you are safe. I will advise whats next.
cheers up
Click to expand...
Click to collapse
No that is not the problem I can not get into the bootloader at all, I use to do it before, so after trying the vol. Down key I tried useing many other combinations without any luck, its as if the default bootloader is gone!
kris29440 said:
No that is not the problem I can not get into the bootloader at all, I use to do it before, so after trying the vol. Down key I tried useing many other combinations without any luck, its as if the default bootloader is gone!
Click to expand...
Click to collapse
HD2 is most great device. what is actually happened. You can brief here what you did before and some background of your HD2, what u have flashed in and what is inside, the more clue probably will help others to point a good thing for you. If No boot loader is the device totally "death"
x1123 said:
HD2 is most great device. what is actually happened. You can brief here what you did before and some background of your HD2, what u have flashed in and what is inside, the more clue probably will help others to point a good thing for you. If No boot loader is the device totally "death"
Click to expand...
Click to collapse
I usely use SD Builds, but I installed DFT_LEO_MAGLDR113_DAF,HSPL4,MAGLDR_CWM_Recovery_v3.0.2.5_for_NexusHD2_135M,NexusHD2-Gingerbread_V2.7_NAND__Android-2.3.4__update and wifi-calling-htcleo-gb-20110518 ( Yes I just copy and paste the file names lol) My phone was working fine (Not sure about the bootloader/Tri-color screen) untill a few days ago my android build boots in safe mode I did find a remedy for that and thats by pressing and holding the Call (green), Home and Windows keys down while the android boots, but I have to do that all the time now. What I am trying to do is restore it back to fatory settings. Oh yeah BTW the AMAGLDR bootloader dose boot and also CWM Recovery but while In the aMAGLDR I have to hold the back key to press vol. up and down other wise it will keep moveing back to the top of the list (Its been like that sence I installed MAGLDR) but I do not have any problems with the vol up and down key in any other programs. I am also able to use USB Flasher and any other mode besides Windows Mobile Device Center (Windows 7). I also tried gettng into Sync by installing Windows phone 7 (witch installed fine with USB flash (Useing MAGLDR) but not luck with syncing back to WM6.
x1123 said:
Is your problem solved ? Hold power key (Red) (Hang Up key) and Volume Down key simultaneously. what is you see on the screen ? if its three color RGB ... you are safe. I will advise whats next.
cheers up
Click to expand...
Click to collapse
Hi. I've tried that combination of keys & I just get the O2 Welcome screen. The only key combination that works is when I power up with the Vol Down key held. I then get the tri-colour screen.
Don't know if this helps but.....
When I get the tri-colour screen, I have the following text:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0X05
CotullaHSPL 0x40