anywhere to get the original front/side part of the case? - Nexus One Accessories

unfortunately, i have dropped my phone on the ground a couple of times, and now, the lighter grey part (front and side) are full of dents and scratches. As you can see in the pictures below.
i had a lot of searches, but couldn't manage to find a replace original case on the web. Does anyone know if I can get one somewhere?

+1 on this

Saw this, from here: http://www.google.de/support/forum/p/android/thread?tid=7921c16b7b46096e&hl=en
CTennant
Level 3
5/18/10
I called HTC at 1-888-231-4736 and ordered the part for $23.99 shipped via Fedex Ground (3-5 business days). A live person answered the phone after 2-3 rings. Ordering directly from HTC is cheaper than htcpedia.com
+ these
http://www.truesupplier.com/brand-n...ates-covers-fasc-pr-24309.html#Detailedimages
http://www.nexusoneforum.net/forum/...u-can-get-replacement-sleeve-nexus-one-3.html
06-24-2010, 03:41 PM #25
ik10
Junior Member
Member #9436
Join Date: Jun 2010
Posts: 1
Phone: Not Listed
Carrier: Not Listed
Here is the direct line for the Nexus One support line:
1-888-216-4736
That should save you a few minutes. Also was able to get a free sleeve and battery cover. They are shipping out tomorrow apparently. My guess is the folks that said it cost money may have called and gotten thier freebie already.
Teardown instructions.
http://www.ifixit.com/Teardown/Nexus-One/1654/1
Could ask this seller:
http://cgi.ebay.com/Battery-Door-Ba...ccessories&hash=item3cb172408e#ht_2125wt_1206
..wonder if you could reverse engineer this:
Dummy phone http://cnn.cn/shop/google-nexus-dummy-phone-p-8442.html
Hope this helps!

Reserved
Sent from my Nexus One using XDA App

I can tell you the construction of the dummy phone for the N1 isn't at all like the actual phone - no useful parts at all.

Sorry to bump an old thread but I am also looking for this part. Everyone seems to sell every part except this one everywhere I look. I found a possible match here globaldirectparts.com/Google-Nexus-One-Replacement-Repair-Parts-s/6177.htm but it's a minimun order of 2 and there is no picture so I'm not even sure if iits the right part. You guys know of anywhere to get this part without ordering a whole housing set?
Thanks!

DizzC said:
Sorry to bump an old thread but I am also looking for this part. Everyone seems to sell every part except this one everywhere I look. I found a possible match here globaldirectparts.com/Google-Nexus-One-Replacement-Repair-Parts-s/6177.htm but it's a minimun order of 2 and there is no picture so I'm not even sure if iits the right part. You guys know of anywhere to get this part without ordering a whole housing set?
Thanks!
Click to expand...
Click to collapse
You can get them from eBay, although they are from Hong Kong and will likely take some time to arrive. The site you mentioned has the same part under Front housing. Basically the front housing is the metal part of the Nexus one. All other parts slide out and are placed inside the metal housing, it's not the easiest or quickest of tasks (Especially if you've never had your Nexus one open) but if you take it slow and careful you shouldn't run into any problems.
Oh and I didn't mean to hit thanks

Hollow.Droid said:
You can get them from eBay, although they are from Hong Kong and will likely take some time to arrive. The site you mentioned has the same part under Front housing. Basically the front housing is the metal part of the Nexus one. All other parts slide out and are placed inside the metal housing, it's not the easiest or quickest of tasks (Especially if you've never had your Nexus one open) but if you take it slow and careful you shouldn't run into any problems.
Oh and I didn't mean to hit thanks
Click to expand...
Click to collapse
You're more than welcome!
Yeah, I have been searching ebay for a few days now and all I can find are the full housing sets (battery cover + Bottom cover + Chassis + Front/Side) or battery door and bottom cover. I bought the phone second hand and everything is in good shape except the front housing. I thought I would just live with it but now I just find all all the chips really annoying.
And I thought the site I linked was probably the right part but ordering two is pointless unless I sell the other on ebay I guess.
Not worried about taking the phone apart, looked at the fixia page and it looks pretty straightforward.

Ebay most definitely
Sent from my Nexus One using Tapatalk

Related

Touch Diamond Replacement Housing!! Help!!!!

I just dropped my diamond by accident while running to my car to avoid the rain =="....
It was in a PDA case, but it still somehow popped out of the case and got scratched up...
So I am in DIRE NEED OF A REPLACEMENT HOUSING!!!
lucky for me, the only damaged parts were the metal rim around the front side of the phone and the battery cover...
I am thinking of just getting an extended battery so i can get a new battery cover with it as well.
But I can't find the Replacement part for the rim around the front of the phone...
I took a lot at the phone and it seems easy enough to replace the rim....but i need to find the part first....
Please guys, any help will be very much appreciated....
Really need this housing replacement...can't stand looking at my scratched up diamond =(
phones still in its early stages so gonna be hard to get hold of housing so quick. Usually best place is here
http://cnn.cn/shop/touch-diamond-c-277_533.html
but they only have screen and back plate at the moment
just be patient a little bit longer.
does that shop deliver quickly??
would it be possible to ask for oem parts directly from htc...?
i talked it over with htc canada today and it may cost upwards 100 CDN to fix the cosmetic damage =(
no insurance?
uh no...i've never insured a phone before....
never thought it would the belt clip would break and let the phone fall and get scratched =="
argh...
any ideas on what to do...
should just take out the rim and touch it up myself ^^"....
oh i've got an idea =D!!!!
I can buy a dummy phone and replace it directly that way...
right.....?
pizzachips said:
oh i've got an idea =D!!!!
I can buy a dummy phone and replace it directly that way...
right.....?
Click to expand...
Click to collapse
In a very rare occasion you can use dummy phones.
Mostly the inside is completely different, no way of using those dummies for housing parts.
Haven't seen a dummy Diamond yet, so I can't tell if it is usable, but mostly HTC dummies aren't usable.
the-equinoxe said:
In a very rare occasion you can use dummy phones.
Mostly the inside is completely different, no way of using those dummies for housing parts.
Haven't seen a dummy Diamond yet, so I can't tell if it is usable, but mostly HTC dummies aren't usable.
Click to expand...
Click to collapse
i'm just lokoing to replace the outer rim on the front side of the phone and the battery cover....?
so maybe its possible...
ill drop by a local mall and see if its possible i guess....
loads of dummy diamond phones on ebay the last time i check it out.
i wouldn't say loads...
i saw a total of 4 =P lol
average 20-30 dollars CDN
which is fine for me if i can use it as housing and battery cover replacement
anyways heading out to check the dummy model =)
it doesn't work =(
its one giant piece, so i can't really take it apart to replace the piece i want...
How hard is it to take apart the diamond?
The invisible shield really stuffed up my screen. I can see parts flaked off the screen (looks like a thin protection layer) which is believe is the touch sensor itself. It has not affected the use of the phone but looks ugly.
EDIT: Home from work and did a search and found this: http://www.pdacenter.ru/razborka/razbor-htc-touch-diamond/
Looks like a lot of work to get to the digitizer.
wow amazing find...was looking for a page like this...
aw man...the housing is one whole piece from what i can tell from the last picture...guess a DIY housing replacement is not really gonna be easy....
i'm gonna ask HTC for an estimate....
just minor cosmetic damage on mine on the corners so nothing too huge but it pains me to see it every time =(
at least this seems a bit easier than fixing the iphone....its so much work to put in a new digitizer cause of the way the housing is built
Looking for the Telus Black rear cover
If anyone finds a place that is selling the black rear battery cover for the CDMA version of the phone i would be interested.
anyone have any lucking finding a replacement housing?
I can provide the replacement housing
It cost about 36 euro
Like this??
http://cgi.ebay.it/ws/eBayISAPI.dll?ViewItem&item=350260913226&ssPageName=STRK:MEWAX:IT

Some Nexus One Parts etc...

http://cnn.cn/shop/advanced_search_result.php?keywords=nexus+one&image.x=0&image.y=0
Ive ordered from here before, and its a great place!
same here. Parts for Cheap!
Is the matte screen protector on there any decent?
I dunno. I've just ordered parts to fix phones, ie screens, keypads, etc and a few battery chargers. Going to love keeping a spare battery on deck again, stupid iPhone.
My Nexus one has a broken LCD but all they have on their site is the digitizer.. Hopefully I can find a replacement LCD soon..
cnn is great, but they ship slooooooow! Keep it in mind if you are on a tight schedule!
Those are not bad prices at that site!
bumpage for the morning folks
Can anyone tell me where to find lcd for nexus?
Nexus one replacement part needed
Does anyone know where I can get a replacement part for the outer shell of the nexus one? The part i need is the aluminum frame that goes around the screen, earpiece, trackball and loops around the lower back... (Picture attached)
I dropped it and the scratches arent bad ont he plastic parts, but the aluminum part near the top (where the earpiece is) is chipped like crazy. Anyone know where I can get this part?
Or if I buy a mock up phone, will it disassemble into the same parts as the external casing for the real thing? Please help! Thanks!
anyone know where i can buy just an external speaker, mine is shot
possible replacement parts source
Searching around for parts for a friends Nexus one myself and found this for the housing.
http://mobile.brando.com/google-nexus-one-replacement-housing_p05399c0670d088.html
Also found this one who supposedly lists parts for the various sub-assemblies http://www.lunacommerce.com/154-nexus-one-spareparts
Have a email sent in to the last one for what they are calling the P/N LNC-GPGNOMB Google Nexus One Mid Chasis. Kind of sucks cause that is really 2 boards and Im only needing the small board that has the sim connector and sd card connector that sits on top of the main motherboard.
Have one broken pin on the sim card that is preventing the phone from being usable at this point and not able to find just the replacement sim connector or the board its on, instead the whole main board would require replacement. doubtful its gonna be cheap either. Anyone have a damaged unit with these cards they want to get rid of?
anyone else having problems using the lunacommerce site? i sent for an enquiry for a part and it said the price was sent to email but is not there?
good to know all these parts are available
Can you fix that SIM connector pin with solder?
Does someone know if the dummy phone have the same material as the real one?
I have also scratches in the aluminium around the phone, wondering if I can take apart the dummy and replace this onto my real one.
http://cnn.cn/shop/google-nexus-dummy-phone-p-8442.html
Ive ordered from CNN as well, parts where nice and fit great... I too am interested in replacement body parts for the N1.
I just looked for some parts around Brando site...
If you enter "Nexus One" as a search string you get all parts they have:
http://mobile.brando.com/search.php?keyword=nexus+one&Submit=Product+Search
as for me, a bit cheaper that "CNN" proposes.
djstoffe said:
Does someone know if the dummy phone have the same material as the real one?
I have also scratches in the aluminium around the phone, wondering if I can take apart the dummy and replace this onto my real one.
http://cnn.cn/shop/google-nexus-dummy-phone-p-8442.html
Click to expand...
Click to collapse
Let me know if you have any luck with this I too have a number of scratches on my device.
This place also has the housing:
http://www.globaldirectparts.com/OEM-Google-Nexus-One-Housing-p/htc736560.htm
Wtf? For 80$ I can live with my scratches...

[Q] Bezel around the screen - replacement??

Hi
I have damaged the metallic black bezel around the screen at a few places (especially the part above the micro usb port). I guess it is called Faceplate.
What I wanted to know is if I can replace this part somehow. If I look at the region under the screen after opening the slider, it appears as if it can come off.
If it is possible to replace it, does anyone know where can I buy one of these?? I have googled but could not find anything.
I have found only a full cover. Try searching milestone 2 housing on eBay.
Or here is the link:
http://www.ebay.de/itm/Cover-Housing-for-Motorola-A955-Droid-2-Milestone-A-955-/300572186204
---UFO--- said:
I have found only a full cover. Try searching milestone 2 housing on eBay.
Or here is the link:
http://www.ebay.de/itm/Cover-Housing-for-Motorola-A955-Droid-2-Milestone-A-955-/300572186204
Click to expand...
Click to collapse
Thanks dude. Now I have to find someone who can deliver it to India. BTW are you sure Droid 2 is physically exactly same as Milestone 2. They do appear same. Just wanted to know if someone has used this cover etc. Plus anything on the quality??
sahilarora911 said:
Thanks dude. Now I have to find someone who can deliver it to India. BTW are you sure Droid 2 is physically exactly same as Milestone 2. They do appear same. Just wanted to know if someone has used this cover etc. Plus anything on the quality??
Click to expand...
Click to collapse
I've ordered one from the link above and I should receive it in the next 7-14 days so I'll let you know how I go but I'm 100% confident that the physical housing between the MS2 and D2 are identical.
I have received the housing (from the eBay link above) and fitted it last night. The case is a Verizon stamped unit and is 100% perfect, next time I think I'll just live with the worn look. Very fiddly job but does give you an appreciation of the engineering ... They use a lot of adhesive, pita.
Well I have managed to knick the display input cable and now have a one centimetre row smack in the middle of the screen that won't respond to touch. My fault, I thought I'd taken care to ensure no damage to some of these fragile cables but alas no
So, just ordered a SGII Stick that where the sun doesn't shine Motorola! Yeah, I know you couldn't care less but I feel better
Well thanks for the info. I won't have the luxury of buying a new one if I ruin my MS2 so I guess I'll stick with a little wear and tear. BTW nice buy!!
Or just take it to your nearest phone repair shop and they'll sort it out. =D
MegaBubbletea said:
Or just take it to your nearest phone repair shop and they'll sort it out. =D
Click to expand...
Click to collapse
Funny bugga, this is BrisVegas!
nurofenplus said:
Funny bugga, this is BrisVegas!
Click to expand...
Click to collapse
Haha true
Sent from my MotoA953 using xda premium
nurofenplus said:
I have received the housing (from the eBay link above) and fitted it last night. The case is a Verizon stamped unit and is 100% perfect, next time I think I'll just live with the worn look. Very fiddly job but does give you an appreciation of the engineering ... They use a lot of adhesive, pita.
Click to expand...
Click to collapse
How does the housing attach to the digitizer/glass? Because the tutorial I found on iFixit didn't detach the digitizer from the housing.
My housing cracked badly, I "fixed" a corner with superglue, but I think it permeated through the digitizer, so there's a strip in the left side (the one with the MENU button) which is insensitive. Another drop and the whole top part fell off and I don't intend to glue this one. Probably I'll buy a new front panel and a new digitizer, but I need to know if I'll be able to attach them at home or if I'll need some adhesive (yuck).
Thanks in advance! :fingers-crossed:

Dropped my phone on concrete :(

And now the pristine MAO case has some horrendous chips and scratches, and I'm really pissed off.
I can't seem to find a reliable or legit looking seller on eBay that will sell a genuine MAO case, the new bevelled USB version. I'm based in the UK, but wouldn't mind buying from an international seller that ships to the UK also. Does anyone know of any good eBay sellers selling genuine HTC parts?
Failing that, does anyone know roughly how much it would cost if I were to send it back to HTC to replace it? I asked HTC support but they don't sell spare parts and can't give a quote unless I send the phone first. Any estimate would be great.
Thanks.
Anybody..?
djsubtronic said:
Anybody..?
Click to expand...
Click to collapse
I'd say you're pretty lucky the screen is intact. Get some black nail polish and fill in the chips, then put one of the super thin cases/skins on it.
el_smurfo said:
I'd say you're pretty lucky the screen is intact. Get some black nail polish and fill in the chips, then put one of the super thin cases/skins on it.
Click to expand...
Click to collapse
The chips are pretty bad. Nail polish is gonna look hideous. Plus the whole point of this phone was to not put it in a case. I'm usually very careful with dropping a phone, this is the first time it's ever happened in my life.
I think I'm just gonna buy a housing off eBay and replace it. And if the housing turns out to be crap (even though they assure it is genuine) then next step would be to insure it and then make a claim.
Hi,
I got a MAO back cover from here: http://www.parts4repair.com/htc-one-s-back-cover/
I asked by e-mail and they say it's an original HTC repair part. I received and replaced the cover and it is indeed indistinguishable from the original. I don't know how it will hold out over time, though.
Before ordering the back cover, I asked an authorized HTC repair service in Switzerland about the repair cost; they said 59 CHF for the cover + labor costs. Like in your case, they cannot estimate labor costs without seeing the phone.
I replaced the back cover myself. It is not that difficult, but you lose warranty (there is a VOID sticker you need to puncture). Be careful that the MAO back cover is structurally different from the gray one: under the lower plastic "flap", there is another black plastic piece that needs to be removed before you can pull the phone from the back cover (first unscrew the two black cross-type screws, then pull out the plastic piece).
Good luck!
doartest said:
Hi,
I got a MAO back cover from here: http://www.parts4repair.com/htc-one-s-back-cover/
I asked by e-mail and they say it's an original HTC repair part. I received and replaced the cover and it is indeed indistinguishable from the original. I don't know how it will hold out over time, though.
Before ordering the back cover, I asked an authorized HTC repair service in Switzerland about the repair cost; they said 59 CHF for the cover + labor costs. Like in your case, they cannot estimate labor costs without seeing the phone.
I replaced the back cover myself. It is not that difficult, but you lose warranty (there is a VOID sticker you need to puncture). Be careful that the MAO back cover is structurally different from the gray one: under the lower plastic "flap", there is another black plastic piece that needs to be removed before you can pull the phone from the back cover (first unscrew the two black cross-type screws, then pull out the plastic piece).
Good luck!
Click to expand...
Click to collapse
Thanks, I knew the difference between the black and gray ones and since mine is black I just want to fix the fact that it's chipped. I'm comfortable with replacing it myself so I might just get it from the website you linked. I just have one question though, can you notice on the replacement cover you ordered whether it has the "new style" beveled USB port? I only want to bother replacing it if it has that USB bevel which indicates it won't have the chipping issue. Other than that, how long have you had it and have you noticed any chipping?
I'd probably fix it myself, it will save money and also won't have to be without a phone.
djsubtronic said:
Thanks, I knew the difference between the black and gray ones and since mine is black I just want to fix the fact that it's chipped. I'm comfortable with replacing it myself so I might just get it from the website you linked. I just have one question though, can you notice on the replacement cover you ordered whether it has the "new style" beveled USB port? I only want to bother replacing it if it has that USB bevel which indicates it won't have the chipping issue. Other than that, how long have you had it and have you noticed any chipping?
I'd probably fix it myself, it will save money and also won't have to be without a phone.
Click to expand...
Click to collapse
I only used it for ~1 week.
Unfortunately, I didn't know about the bevel and did not check. I don't have the phone anymore (it was the S3 version, I sold it and got an S4). If your eyes are better than mine, try looking at these photos:
https://www.dropbox.com/s/u1kq1gdfdrq3zhj/Untitled.jpg
https://www.dropbox.com/s/wmmrv0kgmrmglyr/full.png
I would say that it does not have the bevel, but the quality is not that good. I don't have the full resolution photos either.
doartest said:
I only used it for ~1 week.
Unfortunately, I didn't know about the bevel and did not check. I don't have the phone anymore (it was the S3 version, I sold it and got an S4). If your eyes are better than mine, try looking at these photos:
https://www.dropbox.com/s/u1kq1gdfdrq3zhj/Untitled.jpg
https://www.dropbox.com/s/wmmrv0kgmrmglyr/full.png
I would say that it does not have the bevel, but the quality is not that good. I don't have the full resolution photos either.
Click to expand...
Click to collapse
Ahhh yea those pics are crap. Thanks for your help anyway. I'll think it over and see what I should do.
Just thought I'd let people know. I ordered a case from no.1-tech on ebay (Hong Kong based). Only 20 GBP (including postage) and 12 calendar days later, the case arrived. And at the expense of voiding my warranty, I went ahead to swap the case myself at home. It was a lot easier than expected to do.
So far so good. Seems like a genuine part, but best of all, and much to my surprise, it is the newer beveled USB design as well. Either that or a really incredible fake. Part number matched exactly on the case I removed and it had a date stamp also.
All in all, my phone is now brand new again, with the exception of a small chip that I got on the actual plastic portion around the screen. Not much I can do about that short of getting a whole new digitizer which unfortunately only comes bundled with a screen too. Can't justify 100 GBP to fix a tiny chip on the plastic lol.
djsubtronic said:
Just thought I'd let people know. I ordered a case from no.1-tech on ebay (Hong Kong based). Only 20 GBP (including postage) and 12 calendar days later, the case arrived. And at the expense of voiding my warranty, I went ahead to swap the case myself at home. It was a lot easier than expected to do.
So far so good. Seems like a genuine part, but best of all, and much to my surprise, it is the newer beveled USB design as well. Either that or a really incredible fake. Part number matched exactly on the case I removed and it had a date stamp also.
All in all, my phone is now brand new again, with the exception of a small chip that I got on the actual plastic portion around the screen. Not much I can do about that short of getting a whole new digitizer which unfortunately only comes bundled with a screen too. Can't justify 100 GBP to fix a tiny chip on the plastic lol.
Click to expand...
Click to collapse
could you please post a link of the eBay page where you got the housing? am looking to replace mine also. thanks
Sent from my HTC One S using xda premium
djsubtronic said:
Just thought I'd let people know. I ordered a case from no.1-tech on ebay (Hong Kong based). Only 20 GBP (including postage) and 12 calendar days later, the case arrived. And at the expense of voiding my warranty, I went ahead to swap the case myself at home. It was a lot easier than expected to do.
So far so good. Seems like a genuine part, but best of all, and much to my surprise, it is the newer beveled USB design as well. Either that or a really incredible fake. Part number matched exactly on the case I removed and it had a date stamp also.
All in all, my phone is now brand new again, with the exception of a small chip that I got on the actual plastic portion around the screen. Not much I can do about that short of getting a whole new digitizer which unfortunately only comes bundled with a screen too. Can't justify 100 GBP to fix a tiny chip on the plastic lol.
Click to expand...
Click to collapse
Nice work. Does the disassembly require pry tools (which I suck at) or is it all just screws?
djsubtronic said:
Just thought I'd let people know. I ordered a case from no.1-tech on ebay (Hong Kong based). Only 20 GBP (including postage) and 12 calendar days later, the case arrived. And at the expense of voiding my warranty, I went ahead to swap the case myself at home. It was a lot easier than expected to do.
So far so good. Seems like a genuine part, but best of all, and much to my surprise, it is the newer beveled USB design as well. Either that or a really incredible fake. Part number matched exactly on the case I removed and it had a date stamp also.
All in all, my phone is now brand new again, with the exception of a small chip that I got on the actual plastic portion around the screen. Not much I can do about that short of getting a whole new digitizer which unfortunately only comes bundled with a screen too. Can't justify 100 GBP to fix a tiny chip on the plastic lol.
Click to expand...
Click to collapse
Thanks for sharing your experience with everyone. I wonder how you even started removing the case, since it has no visible screws. I suppose there are videos out there with instructions.
evilRafael said:
Thanks for sharing your experience with everyone. I wonder how you even started removing the case, since it has no visible screws. I suppose there are videos out there with instructions.
Click to expand...
Click to collapse
Pop your plastic covers for starters.
dr_rick13 said:
could you please post a link of the eBay page where you got the housing? am looking to replace mine also. thanks
Sent from my HTC One S using xda premium
Click to expand...
Click to collapse
Here's the ebay link:
http://www.ebay.co.uk/itm/Metal-Fra...t=LH_DefaultDomain_0&var=&hash=item2a1ece2c79
Make sure you select the right option from the dropdown. The Europe based S4 black model is "A".
el_smurfo said:
Nice work. Does the disassembly require pry tools (which I suck at) or is it all just screws?
Click to expand...
Click to collapse
For just the case you can get by without pry tools. You need a T5 torx and a small phillips screwdriver. Once you have the 4 screws removed, apply some pressure on the inner phone assembly that is exposed at the bottom, you basicaly want to push it outwards towards the face of the phone. Obviously be careful with the pushing. It should easily give way as I found it isn't really glued into the housing. You might need a credit card or something to help you ease it out once you have made room with the pushing. I hate pry tools too and had no problem doing it this way. The one thing to be careful about is the plastic assembly at the bottom. Take a good look at how it fits in, so you don't mess it up when putting it back together.
By the way, you can buy HTC void stickers too:
http://www.ebay.co.uk/itm/8-VOID-WA...K_Replacement_Parts_Tools&hash=item337c0261f7
If I ever do need to send it back to HTC under warranty I'm sure those would do the trick
djsubtronic said:
Here's the ebay link:
http://www.ebay.co.uk/itm/Metal-Fra...t=LH_DefaultDomain_0&var=&hash=item2a1ece2c79
Make sure you select the right option from the dropdown. The Europe based S4 black model is "A".
For just the case you can get by without pry tools. You need a T5 torx and a small phillips screwdriver. Once you have the 4 screws removed, apply some pressure on the inner phone assembly that is exposed at the bottom, you basicaly want to push it outwards towards the face of the phone. Obviously be careful with the pushing. It should easily give way as I found it isn't really glued into the housing. You might need a credit card or something to help you ease it out once you have made room with the pushing. I hate pry tools too and had no problem doing it this way. The one thing to be careful about is the plastic assembly at the bottom. Take a good look at how it fits in, so you don't mess it up when putting it back together.
Click to expand...
Click to collapse
how does the lower cover pop off...straight out, like the top?
el_smurfo said:
how does the lower cover pop off...straight out, like the top?
Click to expand...
Click to collapse
I'm really wondering about this also how to take off the bottom cover.. also smurf I have a question for you. It seems like the top contains the WiFi prong. Are you sure the one for cellular signal is on the bottom?
Sent from my HTC One S using xda premium
ickedmel said:
I'm really wondering about this also how to take off the bottom cover.. also smurf I have a question for you. It seems like the top contains the WiFi prong. Are you sure the one for cellular signal is on the bottom?
Sent from my HTC One S using xda premium
Click to expand...
Click to collapse
It almost always is for regulatory reasons (less radiation in the dummy head) even though it makes for less signal when "you're holding it wrong". There's an anandtech review showing the antenna placement as well.
el_smurfo said:
how does the lower cover pop off...straight out, like the top?
Click to expand...
Click to collapse
ickedmel said:
I'm really wondering about this also how to take off the bottom cover.. also smurf I have a question for you. It seems like the top contains the WiFi prong. Are you sure the one for cellular signal is on the bottom?
Sent from my HTC One S using xda premium
Click to expand...
Click to collapse
Well for me I slowly pried the gap at the bottom edge. It's got adhesive on the inside sticking it onto that plastic assembly I mentioned earlier, but just keep prying it slowly so the adhesive doesn't get all messed up. It should flip open like a door with the hinges being where the beats logo is, eventually it'll open right out then just pop it out.
Hi guys,
I got similar story and want to replace my housing.
I have the EU S4 black/red model. I think its one of those with the chipping issue, but not much damage, until the drop which cut the top corner to straight 45 degree white line and scratches my finger every time I use it in landscape mode.
Anyway wanted to ask, since you already tried/used it for some time.
Is the eBay one genuine or just a good fake?
Or is the one from parts4repair a better choice?
Also after removing the bottom plastic cover, as I understand it has glue to it to keep it in place. Do I need to replace that on the reassembly or just heating it back and pressing will work with the old one? Or it has something else to keep it in place other than the glue?

Replacement back cover

To keep it short and simple, I noticed a crack in the back of my tablet today (and I'm not even sure how it got there) so I'm looking to purchase a new cover to replace on my own.
So far, I haven't had much luck; I've only found a handful of eBay listings that are selling used ones for far too much.
Could anyone point me in the right direction?
Not likely to find a parts depot for this device given relative newness and low price point. Probably more cost effective to apply packing/Gorilla tape to the underside or invest in a slim case.
Davey126 said:
Not likely to find a parts depot for this device given relative newness and low price point. Probably more cost effective to apply packing/Gorilla tape to the underside or invest in a slim case.
Click to expand...
Click to collapse
Hi Davey, it's been a long time. Hope you're holding up okay.
I did end up going with one of the eBay sellers and the repair turned out great:
http://www.ebay.com/itm/252243326062?_trksid=p2057872.m2749.l2649&ssPageName=STRK:MEBIDX:IT
The back cover easily snaps off using a guitar pick, plastic tweezers, etc.
The listing says that it doesn't come with buttons, but mine did; either way, taking them off the old one is a breeze as well.
EncryptedCurse said:
Hi Davey, it's been a long time. Hope you're holding up okay.
I did end up going with one of the eBay sellers and the repair turned out great:
http://www.ebay.com/itm/252243326062?_trksid=p2057872.m2749.l2649&ssPageName=STRK:MEBIDX:IT
The back cover easily snaps off using a guitar pick, plastic tweezers, etc.
The listing says that it doesn't come with buttons, but mine did; either way, taking them off the old one is a breeze as well.
Click to expand...
Click to collapse
Nice find and great info. Looks like parts are out there; gotta love eBay. Thanks for sharing!
All is well here; hope the same for you.

Categories

Resources