I had chip on my bottom cover and replaced it for $12. The repair part is real easy though i got a cut lol. One thing i forgot to put in was the dock connector from the previous cover to new one so now i have a n1 with 4 holes rather than 1. And u dont have to void ur warranty for replacing as u dont have to remove and void sticker
here are the links to the things i bought, seems oem and really high grade
http://bit.ly/ctStMp http://bit.ly/bDqrtl
Were you able to take any pictures of the process? Also, where did you get the actual part? I've been contemplating buying a spare bottom rubber thing and battery back, as they are really the most likely places to get scratched. Oh, and congrats on succeeding!
No pictures of the process but u have to open 2 clips one at center n one at right n pull. Assembly is real easy but I forgot to put in dock connectors. They have to removed from previous cover. In the process destroyed a plastic clip opener, older bottom n also cut my finger. No damage to phone though
I'm going to attempt this soon. I ordered the bottom cover from here. They have another bottom cover "with small accessories on their site but I'm not sure what these "accessories" are so I ordered the tools from here.
From my reading, removing the bottom cover can be quite a challenging task.
I also have a new battery cover which I received free from HTC when I called them a few months ago to report it had been scratched. They said they would send me both parts (battery cover and bottom cover) but there was only the one piece. When I called back, they said I would need to send in my phone to have the bottom cover replaced and there would, of course, be a charge.
Finally got the bottom cover in the mail.. it looks as good as the original.
I successfully removed the old one with some precision screwdrivers since my iPod tools haven't come in yet and I couldn't wait. Once I got one of the corner tabs lifted, the cover came right off. Installing the new one was extremely easy.
I wasn't going to replace the battery cover with the new one I had received from HTC but the battery cover had a reddish tint to it so it didn't really match the new bottom cover which is gray. Installed the new one and the phone looks brand spanking new.
did u put in the dock connectors?
charnsingh_online said:
did u put in the dock connectors?
Click to expand...
Click to collapse
They were part of the replacement cover and they're spring-loaded contacts so there was nothing to worry about.
I'm in the process of attempting this
Sent from my Nexus One
Related
I recently bough the extended battery pack (HTC BP E270) and I am satisfied with the new look and feel of the phone, not to mention the improved up time. One very disappointing thing however, is that the new back cover comes off very easily. Simply pulling the phone out of my pocket makes the cover fall off.
The cover is not broken in any way.
Is there a way to make the cover fit tighter so that it doesn't accidentally fall off.
Put glue under it or something I got the same problem as you, backcover to my 1800 mAh is very plastic and the bottom is not fully pressed onto the phone or what should I say.
Thanks Artie. I would however, like to be able to change the cover for the slimmer one at certain occasions. How do you remove the cover if you glued it onto the phone?
Gripenstedt said:
Thanks Artie. I would however, like to be able to change the cover for the slimmer one at certain occasions. How do you remove the cover if you glued it onto the phone?
Click to expand...
Click to collapse
I use double sided tape.
actually, some ordinary transparent tape might be enough to do the trick.
i don't have an extended battery myself so i don't know why exactly it doesn't fit properly, but maybe you can tighten the hold a little at some places by putting some tape on your phone near where the cover holds onto your phone.
Back Cover
blue tac my friends just a small bit in hte right place
Back Cover
blue tac my friends just a small bit in the right place
I have the same original HTC extended battery, It fits right but comes off very easy.
What is blue tac? And where to apply it?
i have the same problem...i think that double sided tape is the best way to resolve this problem...i'll try
p.brazauskas said:
What is blue tac? And where to apply it?
Click to expand...
Click to collapse
http://cgi.ebay.co.uk/Bostic-Blue-T...y_CA?hash=item3ca579e18f&_trksid=p3286.c0.m14
...or bubble-gum, if you're stingy
(i already broke one of the corner bits because of the constant slip-off)
My battery cover is a little loose all of a sudden. at the bottom it now moves a little. When I squeeze (lightly, normal use amount) the phone at the bottom kinda clicks. Anyone else have this issue?
Yes. I called HTC and they're replacing it. But for now what you can do is put paper inside the case
Sent from my HTC Sensation 4G using XDA App
Yeah, several other people reported this problem on a Dutch forum. People should not open the backcover unless they really have to. After opening the cover a few times the cover is getting loose and starts to crack when you press it.
okay so I have the same problem, should I be worried or is it just the case with all sensation handsets ?
Take the cover off and press the battery. I think that's what it is...or maybe both.
Sent from my HTC Sensation 4G using XDA Premium App
secano said:
Take the cover off and press the battery. I think that's what it is...or maybe both.
Sent from my HTC Sensation 4G using XDA Premium App
Click to expand...
Click to collapse
I don't think that's it, the battery is fitted normally, and I've just tested it with battery removed, it does the same thing, I should mention that it isn't really that obvious, but it's an annoyance nonetheless, such an expensive phone to have a glitch like that.
can anybody confirm that it does loosen after some time of usage, I mean did it came like that out of the box or was it getting loose with time?
I just noticed this on mine this morning , will steal a new cover soon
****ttttt let me check mine lol
...same here, at the right bottom corner!!!!
...and I agree, tooooo expensive phone for such a glitch!
Spekko said:
I just noticed this on mine this morning , will steal a new cover soon
Click to expand...
Click to collapse
I went to a tmobile store to see if they'll let me switch. The rep told me thy they can't switch cuz its an htc problem. Then he got curious and pulled out his sensation to see if his had it...
He looked so sad lol I just got off the phone with htc and my replacement cover is shipping soon and if the second one is defective then I have to send in my whole phone so they can check it out. You guys should call htc I'd you already haven't
I fixed mine by adding some paper to the back.
http://forum.xda-developers.com/showthread.php?t=1215096
Hey first post here! Signed up just to have my say on this issue, just as i did with the android central forum.
Also posted this on the android central forums...
Got the creaking here also, definitely a design flaw. Being obsessive with my devices i couldnt live with it!
I do not recommend putting paper in the cover to fill the gap, as this is just expanding the cover further making it even MORE loose when the paper is not in there. Also i wouldn't recommend it because the paper pushes the back cover out a little more, you may loose a connection for the ground. Which is the little metal springy thing, half way up the right hand side. Obviously its not a good idea to 'push' the cover further away from this ground spot. I have heard that people have had issues with screen responsiveness due to a static build up from not grounding properly.
What i did to fix this problem was a bit of a kitbash of sorts.
Mine was creaking on the bottom right area, like most. The problem is there is too much play between the little black catches on the battery cover and the latch on the handset. Instead of filling up the gap between the phone and the cover (Ala paper, card in the cover) I closed it!
What you need to do is get some very thin plastic film. Like that on kids toy packaging etc. Not the thicker stuff though. This stuff would be under 1mm thick. It came as a viewing window in the box my new wallet came in. So you can sorta imagine what im talking about.
I cut a piece about 10mm long and as wide as one of the two little black catches. I applied a VERY thin coat of super glue to one end of the film. Just enough to cover the area under the catch. Then i carefully placed the film with the superglue on it under the catch, and then quickly applied some pressure to it with some tweezers. Then i carefully cut the excess off with a pair of finely tipped nail scissors.
The result is that it now PULLS the screen/phone INTO the cover more by making the little black catch thicker. Not the opposite (paper method), which pushes the cover out, creating a further problem of adding more paper under the cover over time as the cover expands/loosens to compensate. Not to mention a possible grounding loss and resulting damage.
Hope this helps some people that have had multiple replacements or could not be bothered replacing for such a cosmetic issue. (Like me). It definitely works, just got to get your surgeon on and be accurate with your placement of the film.
Apply this to what ever side creaks the most, and bam its gone. Nice. Solid phone... again.
If anyone wants more specific details etc, im all ears.
Regards,
Matt.
MrSoulSOng A video explaining this fix would be appreciated ^_^ cuz I didnt buy my phone from here and I still gotta wait for about a month to send it to the shop to fix or get a replacement
...just an update...after buying new back cover from no1tech (that was month and a half ago...) there's no loose spots, no creacking...!
Very satisfied now I am. Finally phone feels and looks like it should be - beast in compact housing!
I have the very same problem too. VERY annoying
well I had the same problem however what i did was that on the back cover inside of it I put some black electric tape on to the sides that creak (next to the sides and the clips) and when I put the cover back on there was no creaking at all. figured it wont interfere with the single because people put cases on the back all the time plus its electric tape meaning it'll prevent from short circuits and I don't think there should be any overheating issue as its a very small quantity.
Hey,
just got the 16GB from tesco.
When I opened it, (factory sealed box), the case was not clipped all the way on, and the top edge was open a bit. I opened it properly, from the bottom as instructed. Sim car already in, so clipped case on.
Basically there is 1mm gap, right next to the headphone jack and microphone on top of the phone. So, I took case off and had a look. The body has a space for an extra clip next to microphone, but the back case misses this one out (presumably to make room for rubber bit on microphone). I had a look at the pink case in the box, this also misses this clip.
Do other peoples phones case sit tight and flush on the top edge? or is my phone maybe wonky!! I worried the numpty who put the tesco sim in has distorted the chasis, or I just have been unlucky.. Its pretty minor, but its dust access so would prefer a tight fit!
FYI, there stock systems are screwed for xmas. Says out of stock everywhere, including when you phone up the store. I went to a tesco Extra, it had lots and lots in stock. Same price as Tesco direct. So, if you still want one for £129, 16GB. Get to your nearest tesco extra, you may well get one if they have a phoneshop instore.
helppme said:
Hey,
just got the 16GB from tesco.
When I opened it, (factory sealed box), the case was not clipped all the way on, and the top edge was open a bit. I opened it properly, from the bottom as instructed. Sim car already in, so clipped case on.
Basically there is 1mm gap, right next to the headphone jack and microphone on top of the phone. So, I took case off and had a look. The body has a space for an extra clip next to microphone, but the back case misses this one out (presumably to make room for rubber bit on microphone). I had a look at the pink case in the box, this also misses this clip.
Do other peoples phones case sit tight and flush on the top edge? or is my phone maybe wonky!! I worried the numpty who put the tesco sim in has distorted the chasis, or I just have been unlucky.. Its pretty minor, but its dust access so would prefer a tight fit!
FYI, there stock systems are screwed for xmas. Says out of stock everywhere, including when you phone up the store. I went to a tesco Extra, it had lots and lots in stock. Same price as Tesco direct. So, if you still want one for £129, 16GB. Get to your nearest tesco extra, you may well get one if they have a phoneshop instore.
Click to expand...
Click to collapse
The gap is there to allow leverage to get the back cover off. It's annoying that dust can get caught there but it would be a nightmare to remove it if there were no gap. I've had four now from various Tesco stores and they all have this gap, so no need to worry. Just clean out the dust now and again.
I had one which shipped with the case split open like you describe when I first opened it (also 16GB from Tesco).
That phone had a creaky back case - particularly noticeable applying slight pressure to the corner near the speaker. On looking at it I could see the clip on the front of the phone (not the back) was slightly too large, and so you wouldn't be able to fix it with a new back.
Phone went back as it also had a dead pixel in middle of the screen.
I think that the small plastic clips on the front part of the phone can be damaged by not taking the rear of the phone off carefully enough. If they are damaged your phone will always have a loose back, so best not to remove the back too often.
Yes mine is the same and annoyingly someone has used this gap to try and remove the backplate causing it to split at the microphone opening. (2nd hand phone).
So I suggest always removing the backplate from the microUSB end as these are not the sturdiest of backplates.
michael-jb said:
Yes mine is the same and annoyingly someone has used this gap to try and remove the backplate causing it to split at the microphone opening. (2nd hand phone).
So I suggest always removing the backplate from the microUSB end as these are not the sturdiest of backplates.
Click to expand...
Click to collapse
The phones from Tesco include a one page leaflet telling you to put your thumb on the moto logo on the rear and peel it up from the USB, definitely not from the top.
Seeing how flimsy the back is I personally crack open the bottom at the micro USB and then run my fingernail around the gap to pop the back off all the way. The hardest bit to release is the corner above the buttons, which is also where the rear of the case is weakest.
jfinnie said:
The phones from Tesco include a one page leaflet telling you to put your thumb on the moto logo on the rear and peel it up from the USB, definitely not from the top.
Seeing how flimsy the back is I personally crack open the bottom at the micro USB and then run my fingernail around the gap to pop the back off all the way. The hardest bit to release is the corner above the buttons, which is also where the rear of the case is weakest.
Click to expand...
Click to collapse
yea this is how I remove mine. The gap at the top is definitely not there to aid removal of the back. You start from the bottom like you say,
I actually swapped the black back for the pink one included. it fits much much tighter at the top so I think the back can be distorted on poor removal. The downside is I now have a pink phone until I get a replacement
cheers for the responses guys. Good to know its not a problem with my phone as such, just a design quirk..
just got a 16 GB XT1032 from US and i have this same kind of gap in between the body parts on the right side of the audio jack, when the display is facing ground. i freaked out when i found this out. i really expected perfect finishing from motorola.
did someone figure out why is this werid 1mm gap is there or some way to fix it?
Hi guys! I just bought my Moto G from Romania, 16 gb dual sim. Well, today I notice a tiny gap at the right side of the screen, between screen and plastic body. Did anyone else had something similar? The phone it's just great, but I'm a little worried because maybe dust can enter under the screen. I did'nt dropped or something, I just noticed today in the bright light. Thank you
There's no gap in mine. Are you guys making sure that your back cover is completely "snapped" on on all of its sides?
Sent from my XT1034 using Tapatalk
Picture to confirm problem
Hi,
I too have this problem.
Posting a picture
Alright, I did send sms on my bicycle which resulted in I did drop the phone on the ground. Luckily I had ad NILLKIN glass screen protector, which did save most of the phone . I have ordered a new Nillkin screen protector from Aliexpress. And I hope to patch up this phone so it looks good again. How would you have done ?
As you can see at the bottom in the pictures there is physically damage, you can you see the screen bleeding thru also the huwawei logo is damaged.
My idea is UNDER the NEW Nillkin screen protector I will try to mask these "holes" so the screen is not beelding thru anymore. What material should I use to patch up these holes.. also.. how to repar the logo ? can I print it out on my computer printer ? it might look **** on paper but UNDER the glass protector it might look a lot better.
All creative ideas are appreciated, I have high hopes the phone will look good again..
And hopefully my phone will surrive until the M8 release.
Just to let you know desipite the glass look damaged like this the phone is still fully functional!!
ouch i can feel with you.
How about some black film, black paper or everything else that is black and thin
Yes some black material for sure.. Black film would be perfect in guess.. Just wonder where to get it also some black glue at the sides also..
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
alexre123 said:
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
Click to expand...
Click to collapse
Nice man might be a very good alternative! But how easy is it to change it really?
Do I need a heat gun for that?
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Or...if you have the courage go for it ) - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Joke man, don't do it yourself if you don't have experience
alexre123 said:
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Click to expand...
Click to collapse
I have done some smartphone repair myself, I changed the USB board on my old Galaxy Note 1.
I bought a smartphone repair kit with a few tools and very small screwdrivers. To change the glass is probably not much harder, but I need to know if I need a heat gun since I do not own any yet Hopefully it is not needed..but I would assume so...
I might also add the reason I bought a screen protector was that the original glass underneeth have a small crack too that goes accross the entire screen but it s quite invisible besides from certain angels.. so to change that screen to would actually be amazing..and it would make the secondary value when I sell this when M8 is released be a lot higher..
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
alexre123 said:
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
Click to expand...
Click to collapse
Yes the Nillkin glass did its job but I think I was unlucky, that the bottom of the phone got under my bicycle tire.. it felt like it...
I recommend Nillkin, IT has very good Oleophobic coating, which makes the whole device a lot more enjoyable to use, but be careful whren you put it on non 100% straight surfaces it will slip onto the floor.
Alright it is more or less decided I will buy a new front cover with glass, I will make sure to get original parts with gorilla glass. Since the ebay link you linked to are chipped from china I guess I can just order straight from alixpress instead...
I have heard singapore post have quite fast shipping compared to china post.
just one question is hard to see in the videos.. but do I really need to disassembly every component all the circuits boards just to change the front screen ? do I need to open the case at all when using the heat gun/hair dryer ?
If as in the every component and circuit board has to be disassembled it is over my competence probably... unless I am super careful..
Mutch better if you want to purchase an original front to replace it. Don,t know if you really need to take all the components of for replacing the front screen, but you can make some research on it or you can ask on other forums, maybe are others with more experience.
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
blackinfinity said:
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
Click to expand...
Click to collapse
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
ehhm... good luck OP
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
blackinfinity said:
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
Click to expand...
Click to collapse
Sorry but you are like 10 year old child..
So u wanna change your ''front Screen Outer Glass Lens'' ??? (that is damn long name for glass )
You have so much hopes ? OK .. go on .. I leave you to it ..
I wish you very best of luck ..
''''IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT''
DDDDDD this was so funny :laugh: :good:
Fingers :fingers-crossed:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
blackinfinity said:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
Click to expand...
Click to collapse
And I will give you one last advice ; that my detailed post above I explained you how difficult it is .. YOU want to change glass only ??
And what you think, you can just do it without stripping phone apart ?? Are you magician ? You would have to open phone anyway !
And replacing glass on your screen, do you have any idea how you gonna do it? Removing glass from LCD is x10 TIMES hard that my instructions above man !
So you basically adding even more, harder work to hard work ..!
Do you even have
1.LCD separator heat machine ??
2.Cutting line wire ??
3.Cleaning alcohol chemicals ??
4.Optical clear adhesive glue ??
5.Ultraviolet curing lamp ??
Come oon man ...
I told you I wish you very best of luck..
This guy want to do the exact same thing - https://www.youtube.com/watch?v=O8HNBtl9MwI
You have the all process here - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Take a look and decide if you want do it yourself and risk to mess things up or go with the phone and the replacing part to a service and let someone who did this before.
Hi guys
Sadly I have a cracked display...so there are no spare parts available and the shops in Germany would like to have something around 500€.
I changed in the past some Sony-Displays and thought about doing myself. I found on aliexpress some U12+Displays.
Sadly I didnt found a single "manual" or how to, to do this right - anyone can help?
Best regards
Maybe these vids from JerryRigEverything can help you out.
Good luck!
Sent from my HTC U12+ using XDA Labs
https://tinyurl.com/htcu12
Just replaced mine
majomathes said:
Hi guys
Sadly I have a cracked display...so there are no spare parts available and the shops in Germany would like to have something around 500€.
I changed in the past some Sony-Displays and thought about doing myself. I found on aliexpress some U12+Displays.
Sadly I didnt found a single "manual" or how to, to do this right - anyone can help?
Best regards
Click to expand...
Click to collapse
I just replaced mine yesterday and it was more difficult than any other one I've done in the past. Anyway I never found one single video on YouTube that showed the screen removal and pretty much had to play it by ear. There are a few videos that show the disassembly of the U12+ and each stops before removing the screen. My advice is to remove everything from the frame, I managed to piece together enough from the videos to know there are 15 screws to remove, one video said 14 but there's one more that's hidden until you've gotten under the motherboard holding the front facing cameras. Knowing I wanted to keep it simple I didn't remove all of the antenna wires, there's one at the bottom that's under the speaker cover that I left attached so I only disconnected it from the motherboard. Then the other I only disconnected near the vibrator, leaving it connected at the motherboard, so each piece had one wire that stayed connected. Meanwhile you'll have to undo every other plug on the device and with a little persuasion everything fell out. (Don't attempt to remove the button/pressure sensing strips along the sides!) Once you are down to the frame, and for me the ear piece speaker, I used a heat gun to soften the bond between the glass and the frame. It doesn't loosen up very easily, they are really bonded together. I got most of it and then began to chip away at the broken glass. You'll want a good heat gun for this part. I had to set mine to 300F to really get it to loosen up and then work mm by mm around the edge getting all of the glass and glue out of the track. This probably took me a half hour or more. I used E6000 glue but only because I would have had to order B7000 or any other recommended glue. E6000 is a good glue but just because many of the other videos I watched used B7000 I would have liked to use it too.
To install the new screen I used a syringe filled with my glue to follow the small glue track around the edge of the frame. Don't worry about squeeze out because this glue is very forgiving and wipes away easily with IPA Alcohol and a rag. I followed the old glue placement, adding a little extra near the bottom corners and a dab around the ear piece speaker holes. Then it's just reversing the process to assemble the electronics. Now here is another word of warning, the plugs are so small and some are not easy to align but be sure they snap into place and are flat when installed. I made the mistake of not getting the display plug flat and had to do a partial disassembly to correct the issue.
I didn't glue the back on but think I might today just to try and achieve the waterproof level the phone shipped with. You may have to glue yours but I had previously broken the back and already replaced it and the replacement came with a double sided adhesive strip that was still pretty sticky. If I remember correctly the original back was glued on and probably wouldn't have stuck if I had tried to just replace the back as I did.
One other note. After being disassembled and pulling the battery my finger print scanner didn't want to work. In fact it didn't even show up in the menu when I went looking for it but restarting the phone again caused it to show up. My advantage with the double sided adhesive was I was able to test everything and use the phone for a full day before committing to gluing the back on. Now that I know everything is working, the phone is charging and it all seems good I can glue the back on.
Best of luck