During the upgrade of jasjar to wm6.5
After synchronization by activesynic and format the old version
Restart the machine work and entered the boot Loader system
Screen appears, written by usb from the top and bottom of v1.00
And a message from windows xp says usb device not recognised
And stop everything ....
I tried to install the driver of the usb from the cd but the pc does not accept
also tried more pc by xp, seven, vista
But the same thing ....
What is the solution
Related
Does Qtek 8310 need any driver for the USB ?
When i plugin the USB cable the phone starts to charge but windows doesn't recognize it:
http://www.slibe.com/image/c0b945d0-Sliber/
do i need any drivers/software for that (i have activesync)
No need driver for Windows XP after ActiveSync being installed!
try other USB Ports or better yet reinstall ActiveSync, try 4.5, it's the latest release..
Download Here
Can i update the ROM over the miniSD card ?
Because when i turn on the USB cable (PC-Mob) the PC saids "Unknown Device" and when i try another tornado it works so the USB is defect or a part of the phone software. I use bluetooth for the sync but i can't update the ROM.
is it possible (to update from miniSD)?
1. try an other usb port;
2. if you are using windows vista, you need old xp driver: try this guide ( http://www2.webng.com/nionxp/articoli/art_print.asp?artID=41 );
3. if you are using windows xp try to remove activesync, device drivers and reinstall them. (don't use mobile device center in xp: very nice, but programmed very bad without support for all device!).
in every case in informatics you can do all! there's a procedure to load an image from sd to device rom booting from sd but i don't remember the procedure.. follow the first three points before wasting your time.. solving a software problem is more simple..
good luck!
_________________________
>> Smartphone software <<
1. tried on 3 PC-s
2. -
3. I tried on a my friends PC his tornado works my not
maybe the pins are broken so the OS recognizes that there is a device but maybe the TX/RX pin is broken and can't get the info
i think i must extract the setup of the ROM and rename the nk.nbf file to ??.nbf , then insert the card and enter the bootloader
i think the USB connector on the phone is physical defect.
try an other cable, or looking for repair usb pins:
http://docs.sun.com/source/817-3951-12/appA.html#13540
i just tried to update my HTC PU10 windows mobile 5 to WM6 but then the screen got blank and now i think its in boot loader screen as i read in most of the forums. i read most of the forums abt this for 7hrs now and still stuck coz im new to these.
im using windows 7 on my pc so i cant use Activesync so im using windows mobile device center to connect
i tried connecting to mtty1.42 but my MDA dosnt detect in USB as most of the forums say but when i connect to the pc my MDA screen gose serial to USB v1.01 it mean im in the boot loader screen am i right ? so please tell me wht to do next
thanks in advance
Mudith
Welcome to forums
Have a read on the Wiki here:
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Hope it helps,
ok i got my MDA working have to use Windows XP. ROM Update Utility dosnt detect the MDA from USB on Windows7
Windows XP is the best
thanks guys for ur support
hy mudith
i have the same problem with my pda...so please tell me what to do next...i read on forums but my pda doesn't connect on my pc....!!! i don't know what should i do..!!!
Belated Help
Firstly, remove both the SIM card and any memory card. Make sure your battery is charged as well. Can you get into the bootloader (Light button, on/off button and reset button all at the same time)?
If so then your screen should be showing 'Serial' at the top and a number at the bottom. Plug the cable into the XDA and into your PC (it IS a PC and not an iMac I'm assuming?). What OS are you using? XP, Vista or 7?
You need to ensure that 'connect via USB' is DE-SELECTED in either activesync or Windows mobile device centre.
With the cable plugged in, the 'serial' should change to 'USB'. If so all is good. If not, try another cable!
You may also need to ensure you have the correct drivers loaded for Vista and Win 7. I can't get it to work under Win 7 but I can under Vista. XP is preferred for stability for me though.
Now, assuming you have USB on the XDA screen, run mtty (attached to this post) and select usb as the connection type.
Then press enter and you should get a 'USB>' command prompt in the window on the PC. Type (not copy paste) the following:
set 14 0 <press return - don't type this bit obviously!>
Task 28 55aa <press return - don't type this bit obviously!>
Allow each to finish before typing the next and allow the command prompt to appear before exiting.
Then exit mtty and flash a good ROM, I use VNInt with HomeScreenPlus.
Good Luck!
So depressed, this morning, when my phone is in syncing I answered a phone and the mobile synchronous interrupted, Ijoined it to my again, the pc shows"unknown device",
I tried to updated drivers, but no use
I reboot my Touch PRO,the PC also shows "unknown device",
I reflashed a new rom to my phone , the pc shows as the same""unknown device",
I connect my colleagues' HTC C720 and an imate PPC to my PC ,they could be activesynced with my pc. My touch pro also could be synced with their PC
who can help me.It makes me crazy.
Simple mistake. It's possible that everyone may have had this problem before.
It's a Device Partnership Error.
I'll help you with the easiest way to fix this(in my opnion).
1.) Unplug your Device from your PC
2.) Download & Install CCleaner HERE
3.) Uninstall Windows Mobile Device Center/Active Sync from your PC
4.) Run CCleaner (Run the Windows Cleanup & Registry Cleanup [FIX EVERYTHING])
5.) Restart your computer
6.) Download & Install Windows Mobile Device Center/Active Sync
7.) Soft-Reset your phone
8.) Plug in your Phone during its boot-up
Reply with results.
Agent Zach
I followed your instruction
but it's no useful
thanks all the same
Where can i download a free serial usb driver for windows smartphone?
What do you want to do? Serial interface is already included via Bluetooth (incoming and outgoing port) - not sure about USB, despite AS connection in "not enhanced mode (RNDIS)" is said to be "serial" as well.
I need the driver to connect my smartphone to a new pc via usb. My old pc crashed recently and i wasnt able to backup any software. Also, ive lost the cd which came with the phone and i dont know where to get a replacement.
You need a driver for the PC, not on the device. I have no experience with new OS, only Win XP. What happens when you connect the device via USB to the new PC?
My os is winxp. When i connect to the pc it says "found new hardware generic serial" then it brings the found new hardware wizard . I cant continue since i dont have the recquired driver on a removable disk or anywhere on the pc.my phone is spv c600
You need to install Active Sync first on your PC. This should install also all needed drivers for the device to connect. Look here: http://www.microsoft.com/downloads/...34-6f7f-404d-a04b-dc09f8141141&displayLang=en
I have already installed activesync 4.5 but i didnt see it install any drivers.
Is WinXP on the latest Service Pack (SP3 I think) and does it have all Microsoft patches installed afterwards?
AS install should put the drivers to the repository for later install when needed - it will not install the drivers right away. Why don't you let the driver's install look for the drivers in the internet - I don't remember any similar problems on my PC.
Search Microsoft for USB serial driver and RNDIS driver for XP if install does not get it for you automatically.
Oh! It has dected the phone. I reinstalled it while the device was connected to the pc and it worked . thanx so much