Related
This is a patched SPL for HTC Elf devices (HTC Touch / HTC P3450 / Dopod S1, o2 Nova, etc...).
This SPL is based on original Elf 1.11 SPL but includes 3 patches:
g_cKeyCardSecurityLevel = 0 (set 32)
Does not check Model ID
Does not check signature*
(*) code must be formally signed i.e. contain properly-formated signatures on their places, however no checking are performed against them.
This means you can flash ANY ROM to your Elf after flashing USPL on it, no need to pay for CID unlock anymore!
Disclaimer:
This is free to use but at your own risk, I take no responsibility for any conflict, fault, or damage caused to your phone by this unlocking procedure. No warranties of any kind are given. Any commercial usage prohibited.
Instructions:
1. Unzip
2. Connect your phone to computer, make sure activesync is enabled (green icon)
3. Run elf-uspl.exe on your computer and follow instructions on screen:
Code:
*************************************************************
Please make sure Activesync is enabled (green icon in systray)
and hit ENTER to start...
STEP 1/3......50%......75%....100%
The next step will load a patched bootloader (SPL) on your device
it will make your device temporary SuperCID (seclevel=0), and will
avoid modelID and signature checking when flashing NBH files.
Hit ENTER to continue...
STEP 2/3.....15%.....25%...50%...75%.....100%
Phone screen should now be blank and the activesync icon gray
if not, the loading procedure has failed and you'll have to repeat again.
If all was OK hit ENTER and the standard "PDA Phone ROM Update Utility"
window will start, allowing you to flash patched SPL on your device.
Hit CTRL+C to Cancel or ENTER to continue...
Follow the steps on the wizard to flash the patched SPL, when this
step completes your device will reboot.
STEP 3/3 - Launching RUU, please wait...
Process is finished, congratulations!
If you find it useful don't forget to donate :)
*************************************************************
(c)2007 pof - XDA Developers
Hit ENTER to quit.
Update:
Some ROMs (specially O2 Nova) don't allow to run unsigned applications by default and some people have reported difficulties installing USPL. If you see a popup asking to run unsigned code, you need to rapi-unlock your phone manually, to do this download enable-rapi.zip and follow the instructions inside the file prior to installing USPL.
Notes:
1. I have only tested under XP, people says it works on Vista too.
2. Unzip the file, do not run it on the zipped folder. (Note: Better to unzip in c:\ folder with no spaces on the name).
3. This will only CID unlock your device, not SIM unlock.
4. On some devices STEP 2 fails the first time, just hit CTRL+C, softreset your device and start over again.
5. To create NBH files for Elf you should use HTC Rom Tool by Dark Simpson, because "nbhgen" doesn't create proper NBH files for elf.
6. You can use Artemis splash screen tool by jcaron safely on the Elf, the Artemis RUU is compatible with Elf-USPL and both devices have same splash screen format.
7. After flashing a full ROM (containing a SPL on it) you'll overwrite USPL, so you'll need to repeat the USPL flashing process again.
8. If you like it, use the paypal donate button on my signature
Enjoy!
UPDATE (thanks Noonski)
TO AVOID BRICKED ELF BE SURE TO CHECK THIS THREAD:
http://forum.xda-developers.com/showthread.php?t=320155
So new users can first check if their Shipped rom is around before taking the decision to flash USPL.
Also this makes them aware to submit new ones to the list.
And if they Get stuck with a 270 Error at 3% without actually having an original, it was they that made the decision themselves.
Thank you so much! Free CID unlock finally!
Congratulations!!!!
Work in HTC Herald ???
[]s FerSoft
fersoft said:
Work in HTC Herald ???
Click to expand...
Click to collapse
No, this one is only for Elf, but I'll publish a version for Herald soon, its on testing phase
Execellent and will try it right the way...thanks a million....
i did not get what you are saying
This will only CID unlock your device, not SIM unlock
can you please explain me in simple words after after using this tool on my HTC Touch can i use the sim from different service provider
Cool! I finally could update my Spanish Elf to the latest Dopod Asia ROM (WWE)
Thanks!
Greate! I just flash it successfully!
BTW:
pof:How can i flash the device that can not boot? my friend's device only boot in 3-color mode.
Great.. Thank Pro :-*
arifdreamworldera said:
i did not get what you are saying
This will only CID unlock your device, not SIM unlock
can you please explain me in simple words after after using this tool on my HTC Touch can i use the sim from different service provider
Click to expand...
Click to collapse
in simple words: No
there are two different areas in the ROM.
One regarding CID and one for SIM-Lock.
Works perfect in Windows Vista Ultimate 32bit.
Thx pof!
THNX!!!!
THANX a lot pof!!!
You will get a donation from me!
(as I promised here for Excalibur)
Am I right that I can also backup my original ROM and flash it back with that tools?
Thanks And Working Fine With Me .
Great job pof
Oh that's great news for all users HTC Touch,thanks a lot.
This is fantastic! Thanks pof!
Took me 3 attempts, but it worked out great (Vista didnt work though, XP did the third time )
Edit: My dutch Touch, is now a WWE Touch! Thnx again pof. Awesome work.
No success
I went through steps 1 and 2. Then started the RUU with the ELFUSPL hack from pof. But it always gives me the message "[270] UPDATE ERROR" and "Image file is corrupted". I downloaded it again from pof - no change.
Now I wonder if:
1. Is it ok if the ActiveSync icon remains gray (not connected) after the step 2 and during the step 3?
2. Is this method not appropriate for O2 Nova (German)?
Don't know what to do now. Would anyone be so kind and give me any hints, please?
----------------
O2 Nova, German version
How can i see my default settings ?
CID locked or CID unlocked ?
Or all Touch CID Locked default ? ( and i need this flash if i have upgrade "any" rom )
Thx all of your answers !
Follow the steps on the wizard to flash the patched SPL, when this
step completes your device will reboot.
Click to expand...
Click to collapse
this must be a typo then
thanks for sharing the information !
I dont think its a typo. The wizard regards the setup wizard, which is the series of checklist that you go through to get to the end desired result.
Kaiser Sim Unlocker v0.1
========================
Brought to you by jockyw2001
(c)2008 jockyw2001
You definitely save money by using this unlocker, so consider a donation for me to keep the R&D going
Click here to send your PayPal donation.
Download links:
Rapidshare
Megaupload
Note for WM6.1 users
================
Do not try this on 6.1! You will need to downgrade to 6.0
Note for Vista users
===============
This guide will explain how to change your drivers to the xp. You will have problems running the unlocker otherwise. Log in as administrator if you run the ROM update tool and unlocker. That also applies to XP users.
Instructions
============
(The instructions below take preference since they are more current than the readme in the package)
1. To verify you have installed the right HardSPL do this: power off and then press power on while keeping camera pressed, this will enter the so called bootloader mode and you see a tri-color screen (Red, Green, Blue). You should see "SPL-1.0 OliPof" on the second line in the top left corner. You can exit this mode by means of a "soft reset": press the reset button with the stylus.
2. Make a note of the radio version that is currently installed. You see the version strings in the splash screen which appears soon after power on (e.g. "R 1.27.14.09"). Since we will flash a special radio in step 5 you need to flash back your original radio in the last step. You can download radio roms from XDA devs here.
3. Connect PC and Kaiser with a USB cable and keep it connected until the last step.
4. Power on the Kaiser and let it boot into Windows Mobile. On the PC make sure the activesync icon is green
5. After you unpacked the download you see directories "step1" and "step2". Go into "step1" and run KaiserCustomRUU.exe. This will flash the special patched radio rom. Follow the instructions until it is finished.
Note that you can also skip step 6. and proceed with step 7.
6. Power off your Kaiser and insert a 'strange' SIM, i.e. a SIM from another provider than the one your phone is locked to.
7. Once Windows Mobile has booted up it will (usually after you have entered the usual 4-digit PIN) show a window called "Simlock" and a textbox where you can enter a 8-digit unlockcode. Now perform a soft reset by pressing the reset button *but* at the same time keep the camera button pressed. If you did it well you will be back in bootloader mode and you see the tri-color screen. The best technique is to press and hold the camera button first and then shortly press the reset button with the stylus.
8a. right-click activeync icon and uncheck "Allow USB connections" from Connection Settings
8b. On your PC go into the "step2" directory and run "kaiser-simunlocker.exe". If all went well you will see the unlockcode on your monitor and your Kaiser is being restarted automatically.
8c. right-click activeync icon and check "Allow USB connections" from Connection Settings
You should see this:
Code:
=== Kaiser Sim Unlocker (c)2008 by jockyw2001
=== Donations happily accepted, paypal to [email][email protected][/email]
Your Unlockcode = 12345678
[] Done, enter the unlockcode
[] And then flash your original radio
Press Enter to exit
Note: If you skipped step 6 then you should now also skip step 9. and continue with step 9x
9. Once Windows Mobile has booted up it will again show the "Simlock" window. When prompted (usually immediately after you have entered the usual 4-digit SIM PIN), enter the the 8-digit unlockcode and your phone is permanently SIM unlocked
Now proceed to step 10.
9x. (Only if you skipped steps 6. and 9.): Run \windows\simlock.exe on your Kaiser and enter the 8-digit unlockcode when you are prompted.
In order to see simlock.exe you have to open file explorer then click menu > and show all files. If you can still not find simlock.exe copy the attached one to the phone's "My Documents" directory and run it from there.
10. Download the original radio from here to the "step3" directory on your PC and flash it with KaiserCustomRUU.exe
That's all folks
Now you can look forward to some other great tools which I will release soon: "Kaiser SuperCID" and "Kaiser Radio Dumper"
Enjoy and ... donate to keep R&D going! Thx!
JockyW
Credits
=======
* Tom Codon and unkown for testing
* des, pof and olipro for SSPL and HardSPL
* arc and all the other great minds at XDA devs
* viperbjk, adfree and all other QC hackers at Modopo
* PURESKILLZZZ for supplemental instructions here
(c)2008 jockyw2001
[email protected]
Jan 19th 2008
Thanks jockyw2001... trying now, will post feedback
Thanks! Appreciate it: I thought it was just a hype, trying....
Just unlocked...Thanks!!
WoW! Great job JockyW!!!!
Will try it out when I get home!
Nice works my friend...!
Keep up it and don't forget supporting niki device
great great and greater
il conna try it by first daylight thanx and great affoert regards
Great!! Thanks!! Keep up the good work!
gonna try as soon as my battery is over 50%.. will post result
THNX MAN
Instructions followed to the letter here and no dice. At step two i get an error, it reads: "\\.\WCEUSBSH001: No such file or directory cannot connect"
Any help would be appreciated, my OS is Vista Ultimate x64.
kamikaze_decoy said:
my OS is Vista Ultimate x64.
Click to expand...
Click to collapse
Bug detected !!!
Can it apply to all models? such as UK...Thanks...
kamikaze_decoy said:
Instructions followed to the letter here and no dice. At step two i get an error, it reads: "\\.\WCEUSBSH001: No such file or directory cannot connect"
Any help would be appreciated, my OS is Vista Ultimate x64.
Click to expand...
Click to collapse
See if u can find a PC with XP
I stay far away from Vista and never tested it on Vista.
But maybe this helps.
bwqipzbpd said:
Can it apply to all models? such as UK...Thanks...
Click to expand...
Click to collapse
Yes, and goodluck!
Can I use different radio since my original radio is not available for download (my original radio is 1.27.12.29) ?
I use a Kaiser on the UK Orange and I have flashed my phone to Dutty's Rom.
Thank you so much.
Im a UK Orange user. When I spoke to HTC a few months back, the guy I spoke to suggested that Orange are actually using a modified version of the radio rom.
Has anyone using a Kaiser on the UK Orange tried a different radio rom?
Or has the UK Orange radio rom actually been dumped, so we can upload go back to it after unlocking our "beautifully powerful phone"
benz710 said:
Can I use different radio since my original radio is not available for download (my original radio is 1.27.12.29) ?
Thank you so much.
Click to expand...
Click to collapse
You can, but each radio has it's pros and cons. Maybe you should wait until I release my radio dumper. No release date for it yet, but I think in 1-2 wk
i have a question on last step where u have to flash back your radio in "step3 folder", for example, if i need to flash back KAIS_Radinly_1.27.12.17_CustomRUU, but in this zip file has CustomRUU.exe and RUU_signed.nbh, should i put this two files in to "step3 folder", and then click on KaiserCustomRUU.exe (step3 folder). OR it doesn't matter which *.exe files i click, because they are same files, but different filename.
waichai said:
i have a question on last step where u have to flash back your radio in "step3 folder", for example, if i need to flash back KAIS_Radinly_1.27.12.17_CustomRUU, but in this zip file has CustomRUU.exe and RUU_signed.nbh, should i put this two files in to "step3 folder", and then click on KaiserCustomRUU.exe (step3 folder). OR it doesn't matter which *.exe files i click, because they are same files, but different filename.
Click to expand...
Click to collapse
If KAIS_Radinly_1.27.12.17_CustomRUU is a .exe then delete KaiserCustomRUU.exe and run KAIS_Radinly_1.27.12.17_CustomRUU.exe
Hi,
On Step2 it give the error:
\\.\WCEUSBSH001: Permission Denied
cannot connect to \\.\WCEUSBSH001
I'm using XP SP2.
Any sugestions ?
jockyw2001 said:
If KAIS_Radinly_1.27.12.17_CustomRUU is a .exe then delete KaiserCustomRUU.exe and run KAIS_Radinly_1.27.12.17_CustomRUU.exe
Click to expand...
Click to collapse
jockyw2001,
is that mean i don't have to use file in "step3 folder" file?
Treo Pro on CDMA networks - ROMs, Instructions, Tips & Tricks
Flashing...
[size=+1]Instructions:
First, if you have GSM treo pro (NOT CDMA, NOT SPRINT/VERIZON/TELUS), this is not intended for your device. see this post on GSM treo pro's current status: http://forum.ppcgeeks.com/showpost.p...7&postcount=55
steps:
0) if you have Vista or Windows 7, make sure you have latest WMDC.
1) download Hard-SPL package from attachment, extract to an empty local folder.
2) you must Have Phone Synced with PC in Windows Mobile!
3) run PANTHER_CDMA_HSPL exe from the folder
4) follow steps in the program!
5) it should go to tricolour screen now, i.e. SSPL mode, and show 0.32.SSPL. now follow steps in the RUU that's launched by now.
6) SPL flashes, device automatically reboots, job done. if you get any errors, follow the instructions offered by the program.
7) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 0.36.CMONEX.
NOTE: you will not see the SPL version during normal boot!
to enter bootloader mode to see version: with the device turned on, press and hold the Camera button along with the Power button, then press the reset button with the stylus tip, then release the Camera and Power buttons when bootloader tricolour screen appears.
NOTE 2: anyone having problems with the device entering SSPL automatically or problems with USB connection after SSPL was loaded, please copy SSPL-Manual-PantherCDMA.exe from the SSPLManual.zip attachment to the device and run it. then once the screen is in SSPL, run RUU manually. i.e. you run the RUU on the PC, if it isn't obvious.
NOTE 3: this is unsigned Hard-SPL. no limitations on flashing ROMs. also, this has overwrite protection, if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package will soon be posted.
NOTE 4: do not use this RUU to flash anything else! this is only intended for flashing the HardSPL.
Finally, if you wish to thank me with a donation, you can do so by clicking the link the HardSPL program offers, or here: http://hpcmonex.net/htc/pantc/panther.htm
Troubleshooting tips:
- READ THE INSTRUCTIONS
- READ THE INSTRUCTIONS
- READ THE INSTRUCTIONS
- if you have USB issues:
1. anyone having problems with the device entering SSPL automatically or problems with USB connection after SSPL was loaded, please copy SSPL-Manual-PantherCDMA.exe from the SSPLManual.zip attachment to the device and run it (make sure USB is plugged in). then once the screen is in SSPL, run RUU manually. i.e. you run the RUU on the PC, if it isn't obvious.
2. if it still has connection error in SSPL screen, try unplugging and replugging the USB
3. try different USB port, PC, etc.
4. when there are sync issues, the program also suggests installing this file on the phone: http://hpcmonex.net/roms/enablerapinew.cab, just making a note here too.
5. it's been verified that you can flash HardSPL from SD in SSPL, see instructions below.
Updates:
HardSPL NBH file is now downloadable from 1st post! you can flash this from SD now; rename this NBH to PANTIMG.NBH, put it on a fat32 formatted SD, and then run SSPL-Manual-PantherCDMA.exe on the phone.
steps for stock SPL restore:
0. only use this for warranty service! for no other purpose!!! also before flashing this, make sure you already have stock ROM flashed.
1. download Stock_SPL_Restore_036.zip attachment from 1st post, extract it.
2. get customRUU and flash this file. can also do SD flash (PANTIMG.NBH).[/size]
ROMs - CDMA
BigE Rom 23518 v 1.0 - SPRINT
BigE Rom 23511 v 1.2 - SPRINT
CFAY Treo Pro 6.5 Rom - SPRINT
Reserved 3
This is reserved for future use...
Reserved 4
This is reserved for future use...
Reserved 5
This is reserved for future use...
Sprint Treo Pro on Boost Mobile. Will the stock roms also be posted in this thread?
Video Drivers?
Any video drivers like on the touch pro ?
link death, please upload thanks
Stick the list; to get fixed up!
Thx for ROM....
BR
I recently attempted to install WP7 on my tmobile uk HD2,i followed a list of simple instructions but have ran into some problems! Below are the instructions i followed :
If you have had enough details and want to install Windows Phone 7 to your HD2 right away, you can refer to the videos for the download instructions. Though for those of you who have trouble following those instructions, here is what you will need to do:
1.Download the Windows Phone 7 ROM from the link given below and extract its contents to your computer.
2.Make sure that you have HARDSPL 2.08 installed as it is required before you can install MAGLDR in the next step. Also note that your radio needs to be 2.**.50.**. A recommended 2.15.50.14 radio can be found here.
3.Connect your HD2 to your computer via USB and run ‘ROMUpdateUtility.exe’ from the MAGLDR 1.2 folder at the location where you extracted the ROM in Step 1.
4.Follow the on-screen instructions to install MAGLDR on your HD2 and reboot your phone. Your phone will boot into MAGLDR now.
5.Navigate to the 5th option which says ‘USB Flasher’ using the volume-down key and press the green ‘call’ key to enter it.
6.Now run ‘DWI.exe’ from the folder where you extracted the ROM.
7.Read the information carefully and follow the on-screen instructions to flash the Windows Phone 7 ROM to your HD2.
8.Once the installation is complete, your phone will reboot into MAGDLR again. Use the volume-down button to the second option that says ‘Boot AD NAND’ and press the green ‘call’ button.
9.Your phone will now boot into the newly installed Windows Phone 7. The first boot may take a while. Follow the on-screen instructions to setup your Windows Phone 7 installation for the first time.
10.Follow this guide to get Live Services including Marketplace and XBox Live fully working on your device.
Congratulations – you now have Windows Phone 7 running natively on your HTC HD2. Though having to select the second option from MAGLDR every time you restart your phone to boot into Windows Phone 7 can be a hassle. Fortunately, you can set MAGLDR to automatically boot your phone into Android each time you restart it.
I got as far as step 8. My phone did not reboot as it says it will and now i cant do anything with the device apart from make calls from the WP7 os on my phone.
Can any1 help me progress from this problem or to enable me to further enable WP7.
If all else fails can someone post a dumb f**ks guide on how to get back to win 6.5?
ANY HELP WOULD BE MOST APPRECIATED THANKS GUYS
Hi to all
i installed wp7 on my hd2 but i hate it because
1.i cant send and recive bluetooth
2.there is no file manager
3.i cant open my sd card
4. i cant sync my phone with pc
5.when i want to do anything it connects to internet
so i want to uninstal wp7 from my hd2 and install wp6.5 on it
plz help me how can i do this ?!
answer me by email : [email protected]
tnx
all u have to do is to restart ur hd2 in recuvry mode by holding dwn vol buttom and power than connct it to ur pc and lanch the wm 6.5 rom.
it s all
Guys, Help, I get to No 3 of the instructions listed below, the box disapears and nothing else happens, I have downloaded from the links from here http://forum.xda-developers.com/showthread.php?t=893948, from these links
3. Download MAGLDR 1.13 package from *HERE* and extract to an empty folder on your pc
4. Download a NAND Android ROM from *THIS* Forum and extract to an empty folder on your pc any tips on how to over come the problem, keep the suggestions simple please
I've followed the instructions, but keep failing at No3 ....
Please help, lol, and keep it simple lol
1. FLASH MAGLDR TO YOUR DEVICE
The Original MAGLDR Thread by Cotulla is *HERE*
NOTE1: LEO512 and LEO1024 are both supported
NOTE2: MAGLDR doesn't replace OSPL/HSPL. It runs in the chain after. So it's safe to install and remove it
NOTE3: You can flash between 1.11, 1.12 and 1.13 versions on Magldr without losing your NAND Rom
1. Synch Phone with PC in Windows Mobile!!! It has to be connected to activesync or WMDC via USB cable
NOTE: As an alternative method to activesync you can restart your phone in Bootloader Mode, then connect the usb cable and wait until 'usb' appears in the bottom half of your phones screen
2. Browse to the folder you extracted your Magldr Package files to on your pc, right click on ROMUpdateUtility.exe and select Run as Administrator
3. Tick the box to confirm you are aware of the risks and select 'Next'
4. Tick the box to confirm you have followed the preperation steps and select 'Next'
* The program will now check the usb connection *
5. Select 'Update'
6. Verify the image you will flash (it should say 2.00.000.0) and Select 'Next'
7. Read the process list and Select 'Next'
8. Your phone will enter BootLoader Mode and the progress will goto 100%
9. Your phone will now Reboot. Congrats, you just flashed MAGLDR.
NOTE: To Enter MAGLDR Menu Screen after installation, Long Hold the Power Button when resetting the phone and the menu will appear