Hi,
I managed to install Android on my HTC Polaris using HaRET. Everythings works fine (GSM, WLAN, GPS, Bluetooth) except mobile internet via GPRS, EGDE or UMTS. I updated the radio to the latest version I could find for my Polaris (1.65.38.14). I even called my mobile carrier (O2 Germany) to get the correct APN settings. With WM the connection via UMTS works perfectly.
Any ideas what goes wrong? If I would be able to solve this problem, I would abandon WM and flash Android on my phone.
I tried Android 2.1 and 2.1, but the problem remains.
Here are the details of my setup:
Device: O2 xda Orbit 2, i.e. HTC Polaris 200
Android: 2.2
Kernel: 2.6.25-01130-g99a3b07-dirty bell(at)bell-laptop #383
Build:eu_vogue-userdebug 2.2 FR91 eng. martin.20100711.172453 test-keys
Thanks for any help,
Ralf
you can try following to activate mobile inet connection:
- put your phone into airplane on - airplane off
- (re)enter your apn via settings - wireless&network - mobilenetworks - access point names - press menu to enter new apn(s) or reset to defaults.
- force connection using modem.apk (connect/disconnect)
- reinstall/install another build, leave data
- install togga (toggle data connect), put on your sdcard and install via file manager
- use another zImage
- use stock radio
HTH
rhaller said:
Hi,
I managed to install Android on my HTC Polaris using HaRET. Everythings works fine (GSM, WLAN, GPS, Bluetooth) except mobile internet via GPRS, EGDE or UMTS. I updated the radio to the latest version I could find for my Polaris (1.65.38.14). I even called my mobile carrier (O2 Germany) to get the correct APN settings. With WM the connection via UMTS works perfectly.
Any ideas what goes wrong? If I would be able to solve this problem, I would abandon WM and flash Android on my phone.
I tried Android 2.1 and 2.1, but the problem remains.
Here are the details of my setup:
Device: O2 xda Orbit 2, i.e. HTC Polaris 200
Android: 2.2
Kernel: 2.6.25-01130-g99a3b07-dirty bell(at)bell-laptop #383
Build:eu_vogue-userdebug 2.2 FR91 eng. martin.20100711.172453 test-keys
Thanks for any help,
Ralf
Click to expand...
Click to collapse
Have you put the MMC and MNC values for the APN correctly? I had that problem.
Hello,
as posted in another answer, none of warm donut, eclair and froyo was able to get my XDA2(Pola200) online by 3G due booting from haret.
Also none of the tricks given above and in another posts and wikis(i tried everything, believe me)had done the trick.
After flashing it on NAND (Kallt_kaffes eclair RLS7c with latest available eclair kernel), 3G was starting out of the box after boot, w/o further configurations. Curiously with an apn entry from O2. I use a prepaid provider which is based on the O2 network but it has another apn name.
Better be careful, maybe it will be an expensive experience, to go online with the wrong apn entry - in my case it wasn`t.
Anyway, dont`t know what`s the difference relatet to the hardware of my device between Haret and NAND boot and not/working modem.
Matthias
hi matthias,
i have a very similar problem here in austria, using Yesss (which is using the Orange network). i can't get any data connection with froyo build. so i switched back to eclair (VaniljEclair_RLS7c) and 3g connection works out of the box - curiously with an apn from orange.
no idea what is wrong with froyo?
i'm using polaris 200 (xda orbit 2) with haret boot.
Related
I am using the Helmi Cooked Rom and I installed the BBConnect onto my Tilt and the PC desktop software and I can't seem to generate a Pin on my Tilt because it cannot get connected. Any one able to help? (I have the BB plan)
yep
Yes am running the helmi rom myself and all is working well. Check which version of the BB client you have installed, perhaps that is a possible reason.
But works well with the vario III model and said rom installed...
I'm using the newest version 41.0.0.84 posted on HTC site. What version is yours? Did you flash a Hard SPL? or a SSPL? before flashing to the Helmi Cooked Rom?
paulesport said:
I am using the Helmi Cooked Rom and I installed the BBConnect onto my Tilt and the PC desktop software and I can't seem to generate a Pin on my Tilt because it cannot get connected. Any one able to help? (I have the BB plan)
Click to expand...
Click to collapse
Change the AKU version from 0.7.0 to 0.4.2 under HKLM>System>Version>AKU
and it should be fine.
I changed the AKU version and still it shows Data Tunnel Available for half a second and says Disconnected. Anyone know a step by step fix for this?
paulesport said:
I changed the AKU version and still it shows Data Tunnel Available for half a second and says Disconnected. Anyone know a step by step fix for this?
Click to expand...
Click to collapse
I too am interested in a solution...
paulesport said:
I changed the AKU version and still it shows Data Tunnel Available for half a second and says Disconnected. Anyone know a step by step fix for this?
Click to expand...
Click to collapse
The method described above (chaging AKU version) does actually work!
This is what I did:
1. Installed the latest clean cooked rom (CE OS 5.2.1978)
2. Installed Resco Explorer for the registry editor
3. Changed the AKU version from 0.7.0 to 0.4.2 under HKLM>System>Version>AKU (The key difference here is that this change was made before installing BB Connect)
4. Installed BBC v4.0.0.84
5. To configure BBC I used the BlackBerry Connect Desktop for Windows Mobile app which communicated with my work servers and then configured the device for me.
Hope that helps others in the same situation as me.
w01f said:
The method described above (chaging AKU version) does actually work!
This is what I did:
1. Installed the latest clean cooked rom (CE OS 5.2.1978)
2. Installed Resco Explorer for the registry editor
3. Changed the AKU version from 0.7.0 to 0.4.2 under HKLM>System>Version>AKU (The key difference here is that this change was made before installing BB Connect)
4. Installed BBC v4.0.0.84
5. To configure BBC I used the BlackBerry Connect Desktop for Windows Mobile app which communicated with my work servers and then configured the device for me.
Hope that helps others in the same situation as me.
Click to expand...
Click to collapse
Followed these instructions after a hard reset and still no luck. I have the same problem as the others, after step 5 it would connect for a second or so, and then disconnect. So it was back to the HTC Rom.
Sometimes the rom needs to be Hex edited to show that its AKU 4.2 I am sure if you ask Hemli he might do this for you in a future release. I am sorry to say but this is one of those issues that some have beening that the roms we have on this forum have not been made for public release since the 3rd party software has not been properly set up to run with it.
tytn II
Hi all orange uk are releasing tytn II with BB connect version 91
get it here but if you want to use internet explorer you need to edit the registry to disable the proxy for autho connect
if you ahve a look atthe following post it wxplains all
steven
http://sems.org/content/download/bbc4/BBConnect_WM6_Professional_BB_4.0.0.91.cab
also
http://www.sems.org/entry.asp?ENTRY_ID=248
steven
i also found that you have to register the sim card number and imei number in the network i is bb way of protecting licence
i got an upgrade but did not register new sim just used old sim would not work but still worked on old phone eventually spoke to level two in orange and they registered new sim it worked
it is bb s way of proyecting licence
steven
any problems let me know
w01f said:
The method described above (chaging AKU version) does actually work!
This is what I did:
1. Installed the latest clean cooked rom (CE OS 5.2.1978)
2. Installed Resco Explorer for the registry editor
3. Changed the AKU version from 0.7.0 to 0.4.2 under HKLM>System>Version>AKU (The key difference here is that this change was made before installing BB Connect)
4. Installed BBC v4.0.0.84
5. To configure BBC I used the BlackBerry Connect Desktop for Windows Mobile app which communicated with my work servers and then configured the device for me.
Hope that helps others in the same situation as me.
Click to expand...
Click to collapse
I can confirm that these instructions do work with Duttys hybrid no.3 ROM. The only difference is that I installed BBC V4.0.91 version mentioned in this thread.
By the way thank you KarmaNP it did work. I went back to check on what I entered and had too many periods (.)'s when changing the AKU. Make sure that 0.4.2 shows and not .0.4.2 which was my mistake.
I'm noob and recently i've updated my Qtek 9000 (Htc Universal - G3 version) from windows mobile 5 to windows mobile 6.1 from Windows Vista.
I've done it following this guides :
http://forum.xda-developers.com/showthread.php?t=313001
to change windows mobile device driver to USB modem Vista Driver
after that i've followed
http://wiki.xda-developers.com/index.php?pagename=Universal_Bootloader
to upload Universal SPL (Bootloader) to 1.01.
After all of this i've flashed with Tomals 8.5 STANDARD with success uploading my device to windows mobile 6.1.
Now my device is so configurated :
Rom version D.08.50 TML WWE
Radio version 1.03.00
Protocol version 42.36.P8
Actually i have problem with GPRS connection with my Tim Italian network. I must also test UMTS with 3 Italian network.
My device now doesn't establish a connection with network.
Also i want to improve the screen visibility to VGA mode, but i don't know how do it.
Also if it's possible i would understand how can introduce shortcuts to my "home".
I hope that someone help me and thank you in advance.
Bye
johnjohnmel
P.S.where can i find a complete list with the best and usefull software actually available
johnjohnmel said:
Actually i have problem with GPRS connection with my Tim Italian network. I must also test UMTS with 3 Italian network.
My device now doesn't establish a connection with network.
Also i want to improve the screen visibility to VGA mode, but i don't know how do it.
Click to expand...
Click to collapse
1. problem: the networks settings for TIM are available on this list of APNs (apns are access points for gprs network, which you are experiencing problems with as you dont have the proper setup. you should be able to find the necessary information here:
http://forums.pinstack.com/showthread.php?t=360
(sorry for linking to a different board)
as far as i know, you wont need "username" and "password"
2. problem: Use RealVGA and proper ResPacks for it to make this possible
http://forum.xda-developers.com/showthread.php?t=327830&highlight=realvga
(get the RealVGA.cab file and also a ResPack*.cab file like ResPack128dpi.ARM.cab
to get "medium" screen visibility and 96dpi for extremely low size font
greets
the_fish said:
1. problem: the networks settings for TIM are available on this list of APNs (apns are access points for gprs network, which you are experiencing problems with as you dont have the proper setup. you should be able to find the necessary information here:
http://forums.pinstack.com/showthread.php?t=360
(sorry for linking to a different board)
as far as i know, you wont need "username" and "password"
2. problem: Use RealVGA and proper ResPacks for it to make this possible
http://forum.xda-developers.com/showthread.php?t=327830&highlight=realvga
(get the RealVGA.cab file and also a ResPack*.cab file like ResPack128dpi.ARM.cab
to get "medium" screen visibility and 96dpi for extremely low size font
greets
Click to expand...
Click to collapse
Thanks for your prompt help.
I've solved for VGA issue. Thanks a lot.
Does it exist something similar also for Italian ROM, or it's usable only with English ROM ?
For the first point i don't know where i can i ser APN and other parameters on my PDA. Sorry, but i'm a noob.
Looking around settings menù, of this Tomals 8.5 ROM, i find a "connections setup utility" that has entered the right settings for my Tim operator. At least so it seemed.
But unfortunately it didn't function at all.
My PDA is always in searching mode to find an operator.
The strangeness is when i reboot my pda in the first seconds my PDA receive correctly sms from my network operator.
Where can i insert the right settings for Tim italian network, and if it's possible for 3 italian netowrk ?
Many thks again to everybody.
johnjohnmel
provided connection setup should work.
try updating the radio rom to a latest one as I see it is 1.03.
tomal said:
provided connection setup should work.
try updating the radio rom to a latest one as I see it is 1.03.
Click to expand...
Click to collapse
Thanks Tomal, but how can i do ? Sorry but i'm noob.
Where can i find a new Radio ROM ?
Bye
johnjohnmel
P.S.where can i find a complete list with the best and usefull software actually available[/QUOTE said:
THIS IS a cab collection that can be used with the universal, but if you search there are many more! glad you got the rom on and took my advice about Tomals 8.5, it seems that 8.81 is even better now you know how to flash in vista.
Good luck
Jay
Click to expand...
Click to collapse
responderman said:
THIS IS a cab collection that can be used with the universal, but if you search there are many more! glad you got the rom on and took my advice about Tomals 8.5, it seems that 8.81 is even better now you know how to flash in vista.
Good luck
Jay
Click to expand...
Click to collapse
Thanks a lot Reponderman, this Tomal 8.81 regular ROM is AMAZING.
Now i have to solve Radio ROM issue.
Bye
johnjohnmel
Hello.
I am currently trying all versions of Android mentioned in this forum to try and find a stable and compatible version that i can run day to day. Unfortunately i have not yet found a combination that enables wi-fi. The ecliar version enables wi-fi however cannot connect to anything. I am currently using Myn Warm Donut loaded by NAND method. Everything working ok except wi-fi. I have tried both types of NBH files and have tried both methods following instructions contained in the foums. I have also updated with most fixes for wi-fi found in this forum and still not joy.
Does anyone have the same issue? Is this related only to a POLA200? Does anyone have a work around?
Kind Regards
AC
Did you use android update?
Yeah i used android update, before booting into the o/s. I fixed the permissions but nothing changed. Wi-fi will not enable at all. I only have internet access from my network providor.
Kind Regards
AC
Hi, i live in the Netherlands. Is there anyone in the Netherlands how has the Zenithink ZT-180 working with the vodafone USB 3g Stick? ( k3765 )
I read in forums that this combination must work, i disabled cd CD rom function of the stick and filled in the APN information. But it doesn't work.
Help me!
Wich version of firmware do u have?
i have latest 0425 but where i configure APN?
Problem solved...
problem solved...works the internet.
disabled cd CD rom function
disable pin
wcdma
when boot go to apn section
write your isp data
salutare! i have a problem with the new fresh installed rom, the Lion Jelly Bean 4.1.2 ROM for Galaxy S2 GT-i9100, V1.3.
i have no mobile data connection!
After full wipe and install, winth the default modem driver, i activated the mobile data. The icon is green but i have no internet connection. The icon symbol representing the data connection is missing. Strange thing is that when i'm trying to send a mms, the symbol appears and the mms is send.
I checked the ap. there are 2 ap's defined: one for mms and one for data. I tried to define a new one with the settings provided from by mobile data provider and still no data connection.
I installed a new modem driver, the BULP8 corresponding to vodafone romania and nothing changed.
I habe the 3.0.31 jeboo Kernel v1.1.
How can i resove this problem? pls, help.
thanks