I'm starting this thread as I'd like a place to talk about the Fresh Toast kernel as it doesn't look like one has been started yet. If flipz decides to make his own thread at some point then we can delete this one.
The Following is from http://geekfor.me/evo/21/fresh-toast-experimental/
Geek For Me is proud to release:
Fresh Toast Custom Kernel for your Sprint Evo 4g
Experimental, and only available through Fresh Updater.
Fresh Toast was a popular collaboration rom by toastcfh and myself for the CDMA Hero. I am proud to announce that it’s now available for the Evo! Rather than being offered as a separate rom it is now going to be offered as an update/patch for Fresh Evo. If you are running Fresh Rom 0.5.3 or 1.0.0 (testers/donors only right now) then you can get the update by enabling experimental roms in Fresh Updater (more info below). There are 0 changes made to the rom itself other than drivers, all of the changes are in the kernel.
The release notes on this are going to be very brief right now, and so is support. Please report any issues that you guys come across but don’t be too surprised by that due to it’s experimental nature. You all are the testers!
Fresh Toast Features:
* CompCache / ramzswap
o This is actually already included in Fresh Evo, but thanks to the new kernel it is hard coded in there and works a lot better.
* Overclock available up to 1.27ghz, however it doesn’t seem to totally function above about 1.15ghz.
o Only tested with SetCPU. Should also work fine with Overclock Widget. Neither are included.
o If you are reporting OC issues then make sure to say which application you are using. And don’t report it if it’s related to problems when going above 1.1ghz.
* Undervolt — http://en.wikipedia.org/wiki/Dynamic_voltage_scaling#Undervolting
o This lowers the voltage required by the processor at lower clock speeds, thus reducing heat and battery drain.
* Ext4 support — http://en.wikipedia.org/wiki/Ext4
o If using apps2sd then you can convert your ext partition to ext4. Read the wikipedia article for noted benefits.
o You can use AmonRA to convert from ext3 to ext4 without any data loss, just keep in mind that if you try using another rom that doesn’t support ext4 then it won’t be able to read it. Going from ext4 back to ext3 will require re-partitioning your sdcard.
* Both kernels contain extensive tweaks related to speed, power, VM, etc. More details and information to come on all of those tweaks.
* Brain F**k Scheduler aka BFS (optional) – http://en.wikipedia.org/wiki/Brain_Fuck_Scheduler
o One version of the kernel includes BFS and one doesn’t. BFS will definitely make your phone run faster but it’s done with a possible side effect of stability. Test it out and see if you have any issuers.
o If you are reporting any problems with Fresh Toast then make sure and say if you are using the BFS kernel or not.
o If you aren’t sure what a scheduler is: it’s basically what is responsible for queuing up work for the processor to do. From an engineering standpoint even though we can multitask on our phone, the CPU is technically doing only one thing at a time. A scheduler is what controls which job the CPU is working on and which ones are next. This replaces the stock android one with BFS.
Reporting an issue? Please give us which kernel number you are using (#13 or #20 — you can get this by going to Settings < About Phone < Software Information < Kernel Version) and also which overclock application you are using.
Download:
This can only be downloaded through Fresh Updater, and only if you are on Fresh Evo 0.5.3 or 1.0.0 (testers/donors only for now). Users coming from Fresh Evo 1.0.0 should not have to worry about wiping or doing anything special. If coming from 0.5.3 then a wipe might be required to get it booted, I didn’t test. Fresh Updater also has the kernels included with Fresh Evo so that you can go back to them if you have any issues with Fresh Toast. As always make sure you do a nandroid.
You must enable experimental roms in order to have them show up.
Fresh Updater > Menu > Configuration > Rom Update Settings > Display Experimental Roms — Then check for updates.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I'm currently testing out the fresh toast kernels on the DC 3.2.3 rom, I'll post back about my findings soon.
edit: So far it doesn't appear to be working with the DC rom. It's just hanging on boot. I'll give it a bit longer but its already
been sitting on the intial htc EVO 4g logo for 5 minutes.
edit2: I've been unable to get the DC Rom to boot with either of the fresh toast kernels. even with a data wipe. i'm going to try
again.. if anyone else gets it working please post.
Does this have the fps uncap? N if so for which hardware?
madunix said:
Does this have the fps uncap? N if so for which hardware?
Click to expand...
Click to collapse
it does not. given the tearing problem that the toast + epson fps fix kernel has, at this point I just want a kernel
that will enable over/underclocking. the fresh toast kernel fills that niche.
Actually we have been testing this Rom since it came out. Check the last pages of posts here.http://forum.xda-developers.com/showthread.php?t=700448&page=254
cds36 said:
Actually we have been testing this Rom since it came out. Check the last pages of posts here.http://forum.xda-developers.com/showthread.php?t=700448&page=254
Click to expand...
Click to collapse
that thread is about the fresh rom, this thread is about the fresh toast kernel
OneStepAhead said:
it does not. given the tearing problem that the toast + epson fps fix kernel has, at this point I just want a kernel
that will enable over/underclocking. the fresh toast kernel fills that niche.
Click to expand...
Click to collapse
How is it functioning on DC 2.3.2?
blassilando said:
How is it functioning on DC 2.3.3?
Click to expand...
Click to collapse
so far its not booting. i'm going to try a data wipe, but i didn't think that was necessary with kernels.
Relax just saying it is being talked about in his fresh rom thread. http://forum.xda-developers.com/showthread.php?t=700448&page=248 anyone else can reference that as well as this thread.
cds36 said:
Relax just saying it is being talked about in his fresh rom thread. http://forum.xda-developers.com/showthread.php?t=700448&page=248 anyone else can reference that as well as this thread.
Click to expand...
Click to collapse
sorry if i said something to offend you.. it was not my intention at all
OneStepAhead said:
sorry if i said something to offend you.. it was not my intention at all
Click to expand...
Click to collapse
No not at all man, no worries good to have a thread just for this rom. Flipz is doing some amazing work. I have installed a few roms and fresh has been the most stable for me. With this new kernel Rom for the first time I have seen a huge improvement in battery life. Can't wait to see what version 1 brings
does this kernel support the cams? didnt read anything one way or the other yet.
mr_black03 said:
does this kernel support the cams? didnt read anything one way or the other yet.
Click to expand...
Click to collapse
Both work correctly.
If u wanna use my binary in dc or anything else ull have to extract the binary kernel from the boot.img and compile it with the ramdisk from the Rom u are going to flash it to. Also ill need to modify the ramdisk to run compache/ ramzswap scripts and grab the modules from the fresh toast build also. Add all that to ur build and flash the newly compiled boot.img and u should be toasted up
No Problems
No problems here - Flashed using Amon_RA recovery. Running Fresh 0.5.3 ROM.
Quick question - I've been running the Fresh Toast kernal with BFS pretty nicely for about a day now, but I'm still unsure about a few things. How does the undervolting work? Is it automatic if I underclock the CPU, or is it always undervolted? Right now I have SetCPU set to a max of 1152.
nowhere2010 said:
No problems here - Flashed using Amon_RA recovery. Running Fresh 0.5.3 ROM.
Click to expand...
Click to collapse
which one of the kernels are you using
toastcfh said:
If u wanna use my binary in dc or anything else ull have to extract the binary kernel from the boot.img and compile it with the ramdisk from the Rom u are going to flash it to. Also ill need to modify the ramdisk to run compache/ ramzswap scripts and grab the modules from the fresh toast build also. Add all that to ur build and flash the newly compiled boot.img and u should be toasted up
Click to expand...
Click to collapse
thanks, sounds like i have some more learning to do before I could pull something like that off. i'm unemployed at the moment so time is on my side
OneStepAhead said:
which one of the kernels are you using
Click to expand...
Click to collapse
I'm using the one with no BFS.
I just flashed the bfs kernel coming from the latest fresh Rom. I went toast CPU and my max is at 599????
Related
***YOU MUST HAVE RADIO 6.35.xx.xx, SPL 1.76.2007 AND RA's HERO RECOVERY***
**Seems to have an issue in Europe with gps**
I'm not sure why no one has posted a CM5 port.
I've had CM5 running on several different kernels now, Cursors(no 3d), Sanpei 2.6.29(no camera) and several compiled heroc 2.6.29 kernels(no cam, no wifi so far.(I'll post a git link for it soon, smarter people than me are out there and maybe they can do something)
I have been using sanpei's 2.6.32.9 on CM5 for a few weeks now while I compiled and tested others on my second magic, I have everything working, wifi, gps, 3d gallery(first load takes time, fine after that) camera and video work, market is fine, google sign in is good, most live wallpapers work, not one force close(with the apps I use)
You need your sd card partitioned ext3 and yes wipe first.
I've been thinking about posting it for a while now(I have about 20 versions) but with all the #itching some do...well don't, you have a go at fixing it before complaining, legit bug reports are fine, I don't use facebook so I have no idea if it works or not. I also just noticed that shutdown doesn't work(worked now, not sure)so it's a sometimes thing I guess, I've always used adb to reboot to recovery. Reboot works fine.
Everything is pure Cyanogen so props go to him, kernel is sanpei's(thanks for the source help you posted, I know how you feel) and sorry to my wife for me not doing anything but android for weeks now.
I've flashed at least a hundred times over the past few weeks, so if you have boot or flash issues it's something you have done wrong.
I'm on a Rogers magic with the updated radio btw.
Download:CM5 release version < no gapps, if you want them install the zip in the next link.
Download:Gapps
Ok as promised here's the desirec 2.6.29 kernel hack(yes I think I'm a hack lol) in CM5 CM5 with desirec 2.3.29 kernel same applies to this rom as first. No cam/vid, no wifi..yet..If only knew what I was doing.
Source for desirec kernel on sapphire, compiles and boots, no wifi, no cam/vid
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
@528
Bedtime, I'll check this thread in the morning. Oh yes, I'm not responsible if ww3 is caused by this rom.
NANDROID!
10char
d/ling, will flash onto the gf's phone when she gets home.
thanks for your awesome work in advance.
ps/ dropbox is faaaaast, i've been wasting my life waiting for rapidshare...
HSDPA?
Thanks! I'll (hopefully) give it a spin tonight.
Do you have HSDPA working?
Also since you are very eager to use the new radio could you add anything to my question a while ago?
Actually what I found on the forums is not saying much: if someone has proper references please fill in. What I can remember (please I might have it all wrong!):
Advantages of new radio:
- there are some claims of better reception
- some newer roms will explicitly only support the new radio
- more system ram avail (less to user)
- its newer....
*stuff deleted*
Disadvantages:
- less user ram avail (192Meg) ( more avail to system)
- not compatible with some ( ? most at this stage ? ) roms
What would be nice to know is technical advantages like:
maybe better GPS lockon at speed, or better power management, extra capabilities, less processor overheads etc. etc. e.a. some more concrete stuff.
Thank you for this! I have been waiting for CM5 for new radio Much appreciated!
running very nicely so far. haven't really done anything more than install stuff and set up the desktop yet (no switching networks, gps, etc) but wifi works and shutdown definitely does not work :|
Just a word of warning: this is based on CM5 test4!
If you want to flash a theme you need to flash a CM5test4 theme or this ROM will go nuts!
It's easy to repack CM5 into it. One of us will get to it this afternoon if you are patient. It's quite easy to do if you know what to do to the ROM.
But I wont steal the thunder from carz12. He did a good job with update-script that I would have had no idea what to do otherwise.
I still think that things to check for with this kernel in particular are multimedia playback, and camera. If people can test those that would be great.
Actually camera will be corrupted a little because Cyanogen has fixed stuff in there since test4
Give a logcat!
ext2 might work too according to .config if the kernel's filesystem stuff works properly.
ext4 will not work because it was simply disabled
Cyanogen has EXT4 configured for backwards compatibility with EXT2 and 3 instead if I recall cm-kernel's default config for us.
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
# CONFIG_EXT4_FS is not set
Click to expand...
Click to collapse
Also, the kernel does not have perflock enabled, so someone try SetCPU and report back.
Here's the .config extract if anyone wants to take a look:
http://pastebin.com/kdKnqmAN
Testing
Downloading to test it now, been waiting for a long time for a port
Thanks
When CM5 final pot is up it wil be a no-wipe upgrade I expect. So flash away.
carz12 said:
***YOU MUST HAVE RADIO 6.35.xx.xx, SPL 1.76.2007 AND RA's HERO RECOVERY***
I'm not sure why no one has posted a CM5 port.
I've had CM5 running on several different kernels now, Cursors(no 3d), Sanpei 2.6.29(no camera) and several compiled heroc 2.6.29 kernels(no cam, no wifi so far.(I'll post a git link for it soon, smarter people than me are out there and maybe they can do something)
I have been using sanpei's 2.6.32.9 on CM5 for a few weeks now while I compiled and tested others on my second magic, I have everything working, wifi, gps, 3d gallery(first load takes time, fine after that) camera and video work, market is fine, google sign in is good, most live wallpapers work, not one force close(with the apps I use) gapps are in already, I could make one without but this is easier.
You need your sd card partitioned ext3(haven't tried ext4) and yes wipe first.
I've been thinking about posting it for a while now(I have about 20 versions) but with all the #itching some do...well don't, you have a go at fixing it before complaining, legit bug reports are fine, I don't use facebook so I have no idea if it works or not. I also just noticed that shutdown doesn't work(worked now, not sure)so it's a sometimes thing I guess, I've always used adb to reboot to recovery. Reboot works fine.
Everything is pure Cyanogen so props go to him, kernel is sanpei's(thanks for the source help you posted, I know how you feel) and sorry to my wife for me not doing anything but android for weeks now.
I've flashed at least a hundred times over the past few weeks, so if you have boot or flash issues it's something you have done wrong.
I'm on a Rogers magic with the updated radio btw.
Lets see if dropbox works, http://dl.dropbox.com/u/6579155/CM5_32A_NR_SAPPHIRE_2.6.32.9.zip if not I'll post it elsewhere, I'm not sure what the limit is there.
Click to expand...
Click to collapse
Could you please send me the compiled heroc 2.6.29 kernels with CM5? Comparing to sanpei's kernel, I'm more interested in a compiled heroc or hero 2.6.29 kernel that can boot on Magic!
And this is my google account: [email protected]. You can send me an e-mail or talk with me via Gtalk. I want to test your kernels.
Thank you!
Hi,
thanks for porting this
i've tested few things and no FCs so far.
-wi-fi works perfectly
-sliding screens seems a little bit sluggish (just a bit) but I installed LauncherPro and now it's cool
-shutdown works for me
-LEDs are working yeay
some might be interested in neocore results: 23.8 FPS
thanks and
cheers
base?
Is this Rom based on 1.5, 1.6, 2.1 or what?
I'm looking for a FAST stable 1.6 for the new radio and can't seem to find it.
This is a 2.1 based...
fibofan,
Here is a link to a fast, stable 1.6 rom that runs on the new radio. Alan stopped supporting a while back I think but it's great as is (you gotta scroll down to end of 1st post to find link to new radio rom).
http://forum.xda-developers.com/showthread.php?t=654771&highlight=superfast
I made a few updates of my own and use the rom sometimes. If you want me to upload my version and send you the link, just shoot me a PM so we don't hijack this thread.
Awesome work.
Got plans to update to the latest stable CM5 release?
Going to flash tonight and will report back.
Ok, posted(uploading now) a CM5 release version, added 3d gallery back(I like it), no wipe update if you want gapps, or wipe and install CM's gapps pack. I have only just loaded this on my phone, it seems ok so far. Let me know.
xaueious said:
Just a word of warning: this is based on CM5 test4!
If you want to flash a theme you need to flash a CM5test4 theme or this ROM will go nuts!
It's easy to repack CM5 into it. One of us will get to it this afternoon if you are patient. It's quite easy to do if you know what to do to the ROM.
But I wont steal the thunder from carz12. He did a good job with update-script that I would have had no idea what to do otherwise.
I still think that things to check for with this kernel in particular are multimedia playback, and camera. If people can test those that would be great.
Actually camera will be corrupted a little because Cyanogen has fixed stuff in there since test4
Give a logcat!
ext2 might work too according to .config if the kernel's filesystem stuff works properly.
ext4 will not work because it was simply disabled
Cyanogen has EXT4 configured for backwards compatibility with EXT2 and 3 instead if I recall cm-kernel's default config for us.
Also, the kernel does not have perflock enabled, so someone try SetCPU and report back.
Here's the .config extract if anyone wants to take a look:
http://pastebin.com/kdKnqmAN
Click to expand...
Click to collapse
nope no camera corrupted stuff in here
xaueious said:
When CM5 final pot is up it wil be a no-wipe upgrade I expect. So flash away.
Click to expand...
Click to collapse
you are right, and thanks for helping people.
off to work, will check in during the day...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I am in no way responsible for what you do to your phone. Use at your own risk!
At long last we now have a custom recovery for the LG Esteem, actually make that 2 recoveries, Clockworkmod and Raidzero.
RZR is a Release Candidates and CWM is official and can be installed via ROM Manger.
USB Mass Storage doesnt work!!.
CWM, boot isnt listed in mounts and storage, thus cannot be wiped manually. This is normal for some phones.
RZR, boot is listed but will not mount and wipe manually.
Both zips contain scripts for windows and linux, just download to your pc, unzip, and run the appropriate one for your OS. Both zips are All In One, meaning it will root and install CWM or RZR in one step.
Download zip to your computer
Unzip zip
Connect phone to computer via USB cable
turn on and put into Internet connection mode
run the install script for your OS
Booting into recovery with the button combo is a lil tricky (gonna work on this) vol +- and power from power off, it will boot to the LG Reset screen, press power 3 times, dont freak out, it wont erase your data
, and then recovery will appear. Some ROMs are already in the works n will be ready soon, one including reboot to recovery options in the power menu.
Button Combo: VOL +- and POWER, press power 3x at LG Reset Screen.
App - Quick Boot
App - ROM Manager - no other features will work until CWM is submitted and officially built with RM support by koush.
NOTE: Root now works with either ZVB or ZVC thanks to djrbliss!!! Be sure to show him your appreciation!!!
Now for the goods
LG-Esteem-Revo_AIO.zip - Official CWM build for the Esteem available thru ROM Manager!
NOTE: I will be updating RZR as I get the few issues left fixed, but after that I wont be supporting it due to what all I already have on my plate. It is a nice recovery tho with a ton of features. Not for the novice or complete n00b IMO tho.
People to thank other than myself
mtmichealson - dev - help and assistance with development.
interdepth- dev -Transform - help and assistance in brain storming to find n fix for reboot issue.
djrbliss - for the new root for ZVC. Be sure to show him your appreciation!!
DRockstar - for his wonderful scripts I based my shell script from n borrowed snippets for the batch file
koush - for his awesome recovery.
Raidzero - for his RZ Recovery.
Testers - they all deserve major props for testing, bricking phones, patience, and understanding I/we have a life outside of Android.
Image - bricked 1 phone, had replaced.
youngnex - bricked 1, had replaced.
vistor831 - also donated an esteem to the cause, may it RIP! Much appreciated bro!!!
Ære - donated the Esteem I am currently using to dev with, well with vistor831's screen lol, much appreciated bro!!!
ShinySide - 1 brick, BOUGHT a new one.
nuttmeg - bricked 1 phone, had replaced.
redhook
Bigboyyumyum - bricked 1, got it back 98%, had replaced.
aplus
ManlyParasite
If I miss anyone plz let me know so I can add you.
And again thanks guys, your testing helps more than most realize.
PlayfulGod said:
Hello all, we are working on porting CWMR to the LG Esteem. We have it booting and able to flash a boot.img. Problems we seem not to able to figure out tho is CWM reboot about 2min after booting into it resulting not being able to preform backups and testing of other functions.
Does anyone have insight to offer us on what may be causing the rebooting?
Click to expand...
Click to collapse
Hope it can be figured out
Why do I get the feeling noone wants to deal with this device? Is there something special? I would think some devs would be replying here. Cmon guys I know its a metro phone but geesh. Spread some knowledge if you can...thanks.
Thank you PlayfulGod and mtmichaelson for all you have already contibuted...
EvoImage said:
Why do I get the feeling noone wants to deal with this device? Is there something special? I would think some devs would be replying here. Cmon guys I know its a metro phone but geesh. Spread some knowledge if you can...thanks.
Thank you PlayfulGod and mtmichaelson for all you have already contibuted...
Click to expand...
Click to collapse
Its ok, we got it anyhow
[KERNEL] Plague Overclock Kernel for LG Esteem MS910
no dedicated section yet, so i'll just add this in here
Ok folks, as we know have CWM working I can now post my custom overclocked kernel.
Its build from LG source and modified by myself with assistance from mtmichealson. It has a max oc of 1708Mhz (1.7Ghz) with scaling inbetween and even some lower settings added.
Its been running and very stable @1.7Ghz for all I know who are running it. It has 2 additional governors added, smartass2 and interactive. Smartass2 has been reported to revert back to ondemand or performance. I will correct this in a future build or make sure thats what its suppose to be doing.
I would like to thank our team of testers, they been a great help to me and mt, thanks guys!!!
The goods:
Plague Kernel
Download and copy to your sdcard and install with CWM or RZR. No wipes needed. Get SetCPU or similar app to set overclocking.
USE AT YOUR OWN RISK!!!! I am not responsible for anything you do to your phone!
Now we just need an esteem forum here on xda
i am looking forward to further development on this device!! i plan to purchase one soon and im more than willing to contribute!!!
Upon updating the Kernel. I noticed that the camera's UI has changed/ reverted to a earlier version. In my case its not allowing me to change the Megapixel settings. just giving you a heads up. I suspect this being the kernel because I have 2 Esteems. updated on with the plague. then updated the other phone got the same UI on the camera.
i cant seem to get into recovery after rooting.... am i just too slow?
Disregard that last message, i got recovery working fine and running the Esteemed rom as i type this, first i must say this rom is lightning fast... very stable and responsive. love it and looking forward to more development on this device!!!!
[ROM] GingerSteem Extreme for LG Esteem MS910
DISCLAIMER: This is a MODDED' ROM! Use at YOUR OWN RISK!!! By using this ROM, you understand that that I am not liable for any or all consequences of using this ROM. If you don't know what you're doing, DON'T TRY IT. Use at your own risk!
Here ya go folks, GingerSteem Extreme!!! It has been debloated, deodexed, and tweaked for better performance and speed.
Version: 1.1
Developer: mtmichaelson - GingerSteem
Developer: PlayfulGod - GingerSteem Extreme
Description: Modified Stock ROM for the LG Esteem M910
GingerSteem Extreme w/ Plague Kernel
What is this?
This is a very lightweight ROM built both for speed and stability. This ROM is based off of the LG's ZVB update to Gingerbread. It is fully deodexed, and debloated. Swype has also been changed to the 3.26 Beta. A few items have been replaced with AOSP versions to increase speed and decrease size. Also included is the appwidgetpicker to clean that up.
Changelog
v. 1.0 Initial Release
Based off of ZVB Gingerbread 2.3.4
Deodexed
Zipaligned
Heavily Debloated
ADW Launcher
Astro File Explorer
ROM Toolbox - overclocking/underclocking can be set with this app among many other features.
Droid RAZR Boot Animation & sound
AOSP Lockscreen
Accurate Battery Mod
CRT Screen Shut Off
Swype Beta 3.26
Fixed Recovery Not Sticking
Build.prop Tweaks
Init.d tweaks
Battey Charging Animation
V6 SuperCharger Tweak
Loopy Smoothness Tweak
Blocked All CIQ Logs From Carrier and Google (Requires Reboot After Install)
Other Tweaks for Speed and Battery Life
01052012
Plague Extreme oc'd to 2Ghz max
ADWLauncher - CM7 version
GingerFusion Theme added.
Plague Kernel:
Overclocked to 2Ghz
Underclock settings added as well
Interactive governor added
Smartass2 governor added
Tun.ko support
CIFS support
SDCard Read Ahead Speed Tweak
Screenshots
How do I install this?
1.) Download the .zip & copy to phone or sdcard (make sure 4g is enabled if dl'd from phone).
2.) Zip can be installed from either internal or external sd in CWM
3.) MAKE A BACKUP
4.) WIPE DATA!!! (You do not need to wipe if already on GingerSteem!)
5.) Go to install zip from sdcard
6.) Select GingerSteem_Extreme_signed.zip
7.) Do not wipe data after flashing!!!
8.) Reboot!
9.) To Block Carrier Logging Requires Reboot After Initial Boot
Downloads
Esteemed v1.0: GingerSteem_Extreme_signed.zip
*md5sum: 03201d5f800076c8b483054e4ccffc19
Special Thanks!!!
Dev's
mtmichaelson - help and assistance with development, and the use of his ROM as a base for mine.
Testers - they all deserve major props for testing, bricking phones, patience, and understanding I/we have a life outside of Android.
EvoImage
youngnex
vistor831
Ære
ShinySide
nuttmeg
redhook
Bigboyyumyum
aplus
ManlyParasite
spooky
sticky
Themer
spc_hicks09 for allowing me to include his GingerFusion Theme.
Donations
Official Donate link if you like my work and would like to show your appreciation and support. All donations are greatly appreciated!!
ok i think i messed up.... it supposed to be un rooted, but cwm is still there and when i run the restore i have saved it still just boots back into recovery... brick?
ok i solved the issue with i file i found posted on android furums by mtmichaelson 'exitrecovery.zip', was a serious life saver and i beleive that file deserves its own thread lol
PlayfulGod said:
Here ya go folks, GingerSteem Extreme!!! It has been debloated, deodexed, and tweaked for better performance and speed.
Click to expand...
Click to collapse
Is the GingerFusion theme always prevalent, or is there a way for it to look stock?
esoomenona said:
Is the GingerFusion theme always prevalent, or is there a way for it to look stock?
Click to expand...
Click to collapse
its there til another one is flashed. A guy on AF has a stock theme avail tho.
Great ROM! great work throughout. But I'm having some Bluetooth connectivity issues. The phone goes to "force stop" And never connects... I'm assuming your using the same Bluetooth files, so I find it odd that this is happening. should I re flash?
okicu said:
Great ROM! great work throughout. But I'm having some Bluetooth connectivity issues. The phone goes to "force stop" And never connects... I'm assuming your using the same Bluetooth files, so I find it odd that this is happening. should I re flash?
Click to expand...
Click to collapse
prolly wouldnt hurt. Bluetooth working fine for me.
Just re flashed. I'm getting "the application Settings (process com.Android.settings) had stopped unexpectedly. Please try again"
this happens right when I'm trying to pair the phone. Any suggestions?
Sent from my LG-MS910 using XDA App
okicu said:
Just re flashed. I'm getting "the application Settings (process com.Android.settings) had stopped unexpectedly. Please try again"
this happens right when I'm trying to pair the phone. Any suggestions?
Sent from my LG-MS910 using XDA App
Click to expand...
Click to collapse
try running fix permissions in CWM.
Just install this GingerEsteem Rom it and made my day. Was thinking of flashing my Evo 3d to metro pcs cause i thought nobody really cared about this verison andriod phone. Also i have no issue with the bluetooth as of yet. Just flash this 30 mins ago. i be back in a weak from now and keep ya posted on any other defects.
---------- Post added at 06:28 PM ---------- Previous post was at 06:09 PM ----------
Quadrant Scores are unbelievable. I dont get scores like that with Evo 3D overclock.
PlayfulGod & mtmichaelson:
Is there anyway to donate to you guys via Google Checkout? Or do you guys use PayPal for a specific reason?
esoomenona said:
PlayfulGod & mtmichaelson:
Is there anyway to donate to you guys via Google Checkout? Or do you guys use PayPal for a specific reason?
Click to expand...
Click to collapse
I use Paypal becasue it lets ppl donate use their debit and credit cards without having to have a paypal account. I think mt uses paypal because thats what I told him about lol.
I would have to check google checkout to see if indiviual accounts can even be done.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Presents
bhundven's
Subtly Modified Stock CWM 5 KJ6 KernelTHIS KERNEL HAS BEEN DEPRECATED. USE BHUNDVEN'S BLASTOFF KERNEL INSTEAD.
http://forum.xda-developers.com/showthread.php?t=1828171
NOTES
Need help with BLN? Check here: BLN Support
This kernel is still in beta! Please help us test for stability. Logs are always welcome
This is still Bryan's kernel, the only changes I have made were to the initramfs and a few changes here and there to the kernel itself.
Bryan is developing again! This thread will continue to be open to discuss the new releases here unless he decides to open his other kernel thread for XDA.
FEATURES
In addition to the changes bhundven has made:
SuperSU instead of Superuser (adds root support using the kernel alone, regardless of which ROM you install this on)
BLN support added (thanks to neldar and our newest Team Acid member m4xm4n) MARKET LINK
Includes a Team Acid boot splash and recovery image (courtesy of theexel and Tablador)
Cleaned up voodoo extensions directory to remove zipalign for TW launcher
Forcing an ext4 conversion by default regardless of lagfix option
Enabled cifs, fuse and tun kernel modules
NOTES
Want to change your boot splash image? Here's a git repo that helps you do just that:
https://github.com/morfic/Samsung-logo
(Thanks to tablador who linked me to this!)
INSTRUCTIONS
Download the kernel zip file
Flash it using CWM
Wipe the Dalvik Cache before you reboot! (CWM > Advanced > Wipe Dalvik Cache)
If you are already rooted, you can also use the SGS Kernel flasher
DOWNLOADS
kernel-sms-kj6-v0.2.0-bml.zip (MD5: 9cc2278d0d00c61210e1311181de0b67)
Older Versions: Sourceforge
SOURCE CODE
Android SGS4G Kernel at GitHub
Android SGS4G Initramfs at GitHub You might want to use the voodoo branch, not master!
Want to learn how to build the kernel from source? Look at these instructions:
Building From Source
CHANGELOG
Apr 11, 2012
v0.2.0
Enable SVNET_WHITELIST to fix wakelock reboot problems
Bump version to '-sms-kj6-v0.2.0-bml'
Integrated lights.s5pc110.so into the initramfs to add BLN support
-- The kernel itself now copies the file to the rom instead of doing it via CWM
The CWM zip should no longer cause your phone to reboot after the kernel flashes
April 8, 2012
v0.1.1-rc3
Now using SuperSU instead of Superuser
BLN support added (thanks to neldar and our newest Team Acid member m4xm4n)
You need the BLN Control app from the market to use BackLightNotifications! MARKET LINK
February 24, 2012
v0.1.1-rc2
Now using Team Acid's changes to voodoo initramfs
Removed a lot of unneeded checks and their included files since we're only dealing with the sgs4g
Added battery capacity check before voodoo lagfix
Modified the ext4 conversion process to use the bonsai defaults
Forcing an ext4 conversion by default regardless of lagfix option
Removed check for froyo anti_boot_glitch since this is a GB kernel
Enabled cifs, fuse and tun kernel modules
Click to expand...
Click to collapse
Here is Bryan's OP, at the link below
http://forum.xda-developers.com/showthread.php?t=1380331
Flashing.. thanks team acid!!!!!
Sent from my SGH-T959V using Tapatalk
Gasps holy snizzap thanks for this man!!!!!
Sent from my SGH-T959V using XDA App
FB,
I have had to revert both my wifes and my phone to version 2d because of random reboots and locking up with the last 2 of Bhund's releases. Been back on 2d for 6 days now, not a single reboot or lock-up. Do you believe any of the changes you have made will prevent this happening? Or should I stay on 2d for now?
As always, thanks for the contribution.
At the moment it's essentially the same as Bryan's kernel. I've only changed some of the voodoo files right now but you can test if you wish
htaak said:
FB,
I have had to revert both my wifes and my phone to version 2d because of random reboots and locking up with the last 2 of Bhund's releases. Been back on 2d for 6 days now, not a single reboot or lock-up. Do you believe any of the changes you have made will prevent this happening? Or should I stay on 2d for now?
As always, thanks for the contribution.
Click to expand...
Click to collapse
Sent from my SGH-T959V using XDA App
FB you are the man!
Awesome work.
I've looked at Bryan's commits between 0.1.0 and 0.1.1 and actually there was not much. The changes were only to the config file to disable DMA, DIDLE, and some serial interface that got there from aries config. Bigger changes that brought in some kernel code happened before 0.1.0. But the 0.1.0 does not make my phone reboot, and the latest changes don't seem to be significant enough to cause reboots.
I'm going to try this build and see how it behaves. Maybe it was something silly like Bryan's 0.1.1 build was somehow damaged during compilation/linking/packaging.
Good job FB!
Can we do a FULL nandroid restore with this?
Jerry D said:
Can we do a FULL nandroid restore with this?
Click to expand...
Click to collapse
Well its basically Bryan's kernel so I'm pretty sure u can.
-Sent From My Amazing SGS4G-
iHelper said:
Well its basically Bryan's kernel so I'm pretty sure u can.
-Sent From My Amazing SGS4G-
Click to expand...
Click to collapse
Ya. And I did before.. I'm embarrassed to admit that I forgot the issue that made my stop using the CMW 5 version. I probably should've posted in the stupid questions thread.
Thank you for your reply
Big Thanks FB! And Team Acid!
Just flashed and love your new logo..sorry for the stupid question about full restore. I kinda fell behind a little and even forgot some stuff lol.
Hell yeah Team ACID
Looks like that freenode session had some results. I'll give it a go. Thanks.
Pure awesome.
Freaking Brilliant 251
So did cleaning up voodoo scripts allow faster boots.
Sent from my SGH-T959V using xda premium
I had some random reboots when I first flashed Valhalla Black but not sure if it was from the kernel or the ROM. Either way, it was most likely something I screwed up.
Just flashed this new update on my phone and it seems like everything transitions way faster than it used to. And all my apps seem to load faster. I'm mostly sober so I'm reasonably sure I'm not seeing things
Anyway, I don't talk on here much cuz I only get half of wtf you guys are talking bout. Plus there's too many lazy ingrates. But FB, you and the other actual decent people who spend hours working for free have made owning this phone a blast. Thanks for everything you all do and if there's ever anything I can do that doesn't require hard work of any kind, lemme know.
Sent from my A500 using xda premium
Thanks FB, working great.
Sent from my SGH-T959V using XDA App
airfluip1 said:
So did cleaning up voodoo scripts allow faster boots.
Sent from my SGH-T959V using xda premium
Click to expand...
Click to collapse
Not yet. I'm gonna be doing some more work on the scripts tonight since the kernel takes WAY too long to boot. What I noticed from a quick logcat inspection I did before I left home in the morning, it's zipaligning everything every time. I'm thinking it'd be better to only force the zip align once a week so that way you still get speedy apps and you don't have to suffer every time you reboot .
AntonX said:
I've looked at Bryan's commits between 0.1.0 and 0.1.1 and actually there was not much. The changes were only to the config file to disable DMA, DIDLE, and some serial interface that got there from aries config. Bigger changes that brought in some kernel code happened before 0.1.0. But the 0.1.0 does not make my phone reboot, and the latest changes don't seem to be significant enough to cause reboots.
I'm going to try this build and see how it behaves. Maybe it was something silly like Bryan's 0.1.1 build was somehow damaged during compilation/linking/packaging.
Click to expand...
Click to collapse
Hmm. Has it been only certain ROMs giving you reboots? I haven't had issues so far but I have my phone in my pocket all day so I haven't noticed if it does reboot.
Modified kernel (Fb) + VB (Raver) + Adrenaline shot VB with scroll cache tweak (dsexton) = Triple acid burn!
For a while I've been randomly uploading pure cm7 builds for the dream and sapphire as cm made cool changes. At this point, cm7 seems "finished" (the cm team is focusing entirely on cm10 it seems), so I stopped making pure builds. Instead, I will be pulling useful features in and attempt to make a stable, yet feature packed rom.
Release 0.01 (released on September 17 at 00:05) is just cyanogenmod 7.2 with launcher2 and magpie. More features to come.
Requirements:
A htc dream or sapphire 32b with at least danger spl (1.33.0013d spl and 2.22.28.25 radio recommended) or an old radio 32a. I test on a mytouch 3g 1.2 with 1.33.0013d and 2.22.28.25.
Flashing instructions.
1. Download the rom, kernel, and optionally gapps to your sdcard.
2. Make sure you are in recovery mode with a custom recovery.
3. If you are coming from any other rom besides the pure cm7 builds on dw9906's thread, wipe userdata, cache, sd-ext, and system.
4. Apply any custom mtd setup you wish. I don't use custom mtd so I don't know what sizes are best for this rom. (Optional)
5. Flash the rom
6. Feed the cat. he's very hungry. Neglecting your animals so you can flash roms constantly is bad.
7. Flash the kernel.
8. Flash gapps
9. Reboot.
10. Enjoy.
Downloads:
Rom: http://www.mediafire.com/?gkdvgk7l6mrz94u
Kernel: ezgb kernels
Gapps: I don't include or distribute these. You should know where to find them.
Bugs: none I know of
Features: magpie, launcher2
Future features: autokernel. Kernel built with linaro. Kernel with bfs.
Thanks to:
Google - android
CyanogenMod team - the awesome rom
Firerat - magpie
Ezterry and AndDiSa - kernel
Infinimint and the united dev team - hosting and support
My girlfriend - for putting up with this time consuming hobby. I love her.
//reserved
Sources coming soon. My current setup is a little messed up. Need to fix it.
Note: rules on using this rom for other projects
Most of android is under the apache2 license. just don't violate that and we're good.
more specific rules: source is on my github, do whatever you want within the terms of the licences. make your own rom, use it to port other devices, release a rom that is exactly the same with a new name and a shiny theme, I don't care as long as you are building from source.
If you use prebuilt anything from releases of this rom, please be nice and send me a pm asking for permission. this is supposed to be an open community, but i hate seeing 20+ cm7 roms with nothing different except name and bundled apps. If you don't ask, and you havent made something different enough from this rom to be worth having its own thread, it may or may not get reported.
is it still the same with the "original" cm 7.2?
Does this ROM support 32A devices with old radio (3.22)?
adityo97 said:
is it still the same with the "original" cm 7.2?
Click to expand...
Click to collapse
it has magpie and it uses launcher2 instead of adw. other than that it's almost the same as pure cm7 at this point.
tass0s said:
Does this ROM support 32A devices with old radio (3.22)?
Click to expand...
Click to collapse
it should. I don't have access to a 32a so i'll have to wait for you to confirm
tvall said:
it should. I don't have access to a 32a so i'll have to wait for you to confirm
Click to expand...
Click to collapse
Ok, unless somebody else does it, i will try these days for sure.
well... got a shiny new kernel compiled with linaro. so far so good. should i post it, or should I wait till i've tweaked it a little more?
tvall said:
well... got a shiny new kernel compiled with linaro. so far so good. should i post it, or should I wait till i've tweaked it a little more?
Click to expand...
Click to collapse
tweak pleaseee. woohooooo
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my Dream/Sapphire using Tapatalk 2
evall said:
Sent from my Dream/Sapphire using Tapatalk 2
Click to expand...
Click to collapse
32A?
Mytouch 3g 1.2 (the one with the headphone Jack and more ram)
http://www.mediafire.com/?py8asp6ab109dyl
new kernel. might or might not help speed things up. built with the linaro toolchain
Link not working on Opera Mini
That's weird, using Opera Mini the ROM download on MediaFire isn't working... left it for ages but remained on "0/52.46Mb". The kernel downloaded fine though
Oh well, working now, gonna try it as Cronmod is being slow on me
i was wondering, what's the difference between the "linaro" and the usual kernel build?
adityo97 said:
i was wondering, what's the difference between the "linaro" and the usual kernel build?
Click to expand...
Click to collapse
The linaro toolchain has a ton of arm optimizations that should make stuff compiled with it perform better. Cm was considering using it to build pretty much all of cm9, but found it caused random stability issues.
My girlfriend has been running the kernel for days and has yet to have any major issues. She also hasn't said if it helps..
tvall said:
The linaro toolchain has a ton of arm optimizations that should make stuff compiled with it perform better. Cm was considering using it to build pretty much all of cm9, but found it caused random stability issues.
My girlfriend has been running the kernel for days and has yet to have any major issues. She also hasn't said if it helps..
Click to expand...
Click to collapse
and is it really the Linaro make cm7 faster? sorry for asking, just curious bout the linaro after i watched it on youtube
haven't tested thoroughly enough to confirm. This rom also uses launcher2, which is a lot faster than adw
tvall said:
haven't tested thoroughly enough to confirm. This rom also uses launcher2, which is a lot faster than adw
Click to expand...
Click to collapse
can this kernel used on FBL?
adityo97 said:
can this kernel used on FBL?
Click to expand...
Click to collapse
USB storage won't work. Other than that, should be fine
I ported Cyanogenmod 9 for the Hero build by Jordfaz. (Thanks to him!)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Downloadlink: Cyanogenmod 9
Installation:
- Flash Lights_format_all (See other thread!)
- Flash CM9
- Reboot
- 32B: Flash a 32B kernel after flash of the ROM
After installation
- After boot: Go to ADWSettings - system - advanced - enable wallpaper hack and scroll cache: low quality --> This will fix your UI.
- To disable CRT-animation: Displays - animation OFF (Thanks toi SaySpaceman! ;p)
Working:
- Calls/SMS
- Data
- Youtube!
- Screenshot!
- Perfect rotation!
- ...
Not working:
- Bluetooth
- GPS
Changelog:
Code:
-- Cyanogenmod 9 --
v1.0
* Initial release
Hit the THANKS button, if you use this ROM!
I will complete this thread at a later time, but for the next month I'll have to study a lot , so maybe no time for uploading and completing thread.
You can disable the CRT animation. You go to Settings->Display->You turn off the Screen off animation.
I haven't found any bugs yet, everything works very smooth and even YouTube works! :good:
I think this is the best ROM for our "legacy" device
SaySpaceman said:
You can disable the CRT animation. You go to Settings->Display->You turn off the Screen off animation.
I haven't found any bugs yet, everything works very smooth and even YouTube works! :good:
I think this is the best ROM for our "legacy" device
Click to expand...
Click to collapse
Thank you! Didn't know you could manually enable/disable it.
i really want to try this rom in my old htc magic!
I would like to know wich recovery do you use and recommend to flash your rom.
another question is the funcionability of the apps with this rom
thank you for all your work for "our" device.
stiker said:
i really want to try this rom in my old htc magic!
I would like to know wich recovery do you use and recommend to flash your rom.
another question is the funcionability of the apps with this rom
thank you for all your work for "our" device.
Click to expand...
Click to collapse
I think you can only flash it with CWM recovery.
All apps that work on GB, will work in ICS.
But the Play Store will show a lot more apps, but a lot of them will force close when you try to open them.
But in general, everything should be smoother.
ok. This rom is good. But it is slow when download from playstore. Thanks!
Thanks for CM9, i was looking for some stable rom
I will try this ROM and will let u know my findings
Thank you for porting this over. I have neglected my HTC Magic for quite some time now, finally got it out, dusted it and went through the flashing bits for this. Stable and much smoother than I expected to have on a (relatively) dated device. Are the processor options under 'Performance' settings disabled or is it meant to be on 'ondemand' all the time?
Yanguang said:
Thank you for porting this over. I have neglected my HTC Magic for quite some time now, finally got it out, dusted it and went through the flashing bits for this. Stable and much smoother than I expected to have on a (relatively) dated device. Are the processor options under 'Performance' settings disabled or is it meant to be on 'ondemand' all the time?
Click to expand...
Click to collapse
You can't change any options in Performance. I'll see if I can change that, because now, if the displayed CPU speeds are right, the CPU is constantly running on 710 Mhz when you used it.
Default cpu frequence 710MHz is not stable enough to bootup my phone, could you please lower down to 650MHz please?
jejer said:
Default cpu frequence 710MHz is not stable enough to bootup my phone, could you please lower down to 650MHz please?
Click to expand...
Click to collapse
Did you try to flash it? My phone doesn't run on 710 either, but it does boot.
Yes, I flashed it. During boot, cat /proc/cpuinfo get 710MHz and boot failed. After set it to 620MHz, it bootup success.
Your ROM works great, thanks!
jejer said:
Yes, I flashed it. During boot, cat /proc/cpuinfo get 710MHz and boot failed. After set it to 620MHz, it bootup success.
Your ROM works great, thanks!
Click to expand...
Click to collapse
Ok, thanks! I'll set it to a lower speed in next version.
I would really advise against overclocking by default. The majority of these devices can overclock to acceptable speeds, but others can't do much at all. My mytouch 3g, for example, would freeze at anything above 595mhz, and it was most stable at 537 or below. So even with that lower overclock you decided on, I still wouldn't be able to use this without modifying the rom.
There are plenty of ways to make this recommended, but optional. You could put an oc script in a separate zip to flash. Or you could start using the fancy Aroma installer. Ezterry's yesno binary is really easy to implement.
tvall said:
I would really advise against overclocking by default. The majority of these devices can overclock to acceptable speeds, but others can't do much at all. My mytouch 3g, for example, would freeze at anything above 595mhz, and it was most stable at 537 or below. So even with that lower overclock you decided on, I still wouldn't be able to use this without modifying the rom.
There are plenty of ways to make this recommended, but optional. You could put an oc script in a separate zip to flash. Or you could start using the fancy Aroma installer. Ezterry's yesno binary is really easy to implement.
Click to expand...
Click to collapse
I didn't know the cpu was running at a higher speed. I thought it was a bug in performance section, who was showing the wrong speed, since my HTC Magic normally freezes at 710 Mhz.
It's been years since I last flashed a MyTouch3G (32B)... Just got back one that I'd gifted away two years ago, it decided not to boot around Christmas and I brought it home to wipe/reflash.
Glad to see work still being done on this old device! It's ahead of my G2X in Roms.. That's effin sad.
Now if I can just remember how you flash a kernel on this thing....
EDIT:
I'm a bit confused about the kernel.... the thread linked doesn't actually seem to be any specific kernel??? More "how to flash a kernel safely" and hboot/radio files. I already have the required hboot/radio! So which kernel do I use??
EDIT 2:
N/m.... can't be assed to sit here all night trying to figure out which kernel to use on an antique phone. Went with Gingerbread instead.
tutorial and links - SPL/radio/ROM
lotherius said:
It's been years since I last flashed a MyTouch3G (32B)... Just got back one that I'd gifted away two years ago, it decided not to boot around Christmas and I brought it home to wipe/reflash.
Glad to see work still being done on this old device! It's ahead of my G2X in Roms.. That's effin sad.
Now if I can just remember how you flash a kernel on this thing....
EDIT:
I'm a bit confused about the kernel.... the thread linked doesn't actually seem to be any specific kernel??? More "how to flash a kernel safely" and hboot/radio files. I already have the required hboot/radio! So which kernel do I use??
EDIT 2:
N/m.... can't be assed to sit here all night trying to figure out which kernel to use on an antique phone. Went with Gingerbread instead.
Click to expand...
Click to collapse
<<Check my signature below!>>
<<Goog flashing>>
Edited post (correction below)
Sorry for the wrong info on flashing your 32B device, I did not notice that your device was not a 32A sapphire but the 32B instead!
I think the answer you're looking for is here:
[ROM][WIP] United ICS - http://forum.xda-developers.com/showthread.php?t=1647493
"kernel -
ezterry's kernel + ics patches and some performance tweaks (enabled 710mhz overclock and other things) http://www.mediafire.com/?py8asp6ab109dyl
ezterry's ezgb 1.5.2 http://sandbox.devnull.name/android/ezgb-kernel/ezgb-2636-v1.5.2_S.zip "
<< info from tvall - http://forum.xda-developers.com/member.php?u=3038499 >>
lotherius said:
It's been years since I last flashed a MyTouch3G (32B)... Just got back one that I'd gifted away two years ago, it decided not to boot around Christmas and I brought it home to wipe/reflash.
Glad to see work still being done on this old device! It's ahead of my G2X in Roms.. That's effin sad.
Now if I can just remember how you flash a kernel on this thing....
EDIT:
I'm a bit confused about the kernel.... the thread linked doesn't actually seem to be any specific kernel??? More "how to flash a kernel safely" and hboot/radio files. I already have the required hboot/radio! So which kernel do I use??
EDIT 2:
N/m.... can't be assed to sit here all night trying to figure out which kernel to use on an antique phone. Went with Gingerbread instead.
Click to expand...
Click to collapse
You have to take a working 32B kernel, preferably a flashable zip. The link in the opening post isn't directing to a kernel, but search for it in the G1 section and you will find a lot kernels.
ICS is much faster, so I would suggest you try it.
Can you point me into the right direction? My dad has an old Magic 32B with Radio 27.08. What Kernel should i use? Or what ICS Version are you talking about?
Thanks in advance.
when is out the final version?