Related
OK
I've always had troubles flashing radios for some reason, I've managed to just not do it but now with Duttys 6.1 out I really need some help
- I've flashed Duttys latest successfully
- I've flashed HardSPL
- But whenever I flash the radio (1.64.08.21) I get a connection error at 99%!!
Now I can still get into the phone using mtty and the boot command.
Am I doing something stupid -- Any help gratefully received!
Alex
ps - I have a UK o2 XDA Stellar
I'm a newbie been here with a AT&T Tilt less than a week and I promise I'm reading, but I'm having the exact same problem. Flashed Duttys dual V4 as my first try last Tuesday without a problem and of course be a crazy new guy I wanted his newest work. So I flashed Duttys 6.1 today and I guess I just can't figure out how to flash radios, because I've tried 2 now and both error out at 99% and I too have to use mtty to get back into the phone. I'll keep reading, but if someone could tell us new guys what the heck we are doing wrong that would be great.
PS I'm glad to be here and this looks like a lot on fun thanks for having me and look forward to helping out someday.
JMan
Hey Alex! I figured it out Brother! Do this and you should be able to upgrade your radio. I was using JumpSPL1.56-KAIS run from my device and I was running into the same problem everytime I tried to upgrade my radio. Would get to 99% and then would error out. So I followed these steps taken from a number of different post and put together until it worked!
1) Make sure you have JumpSPL1.56-KAIS somewhere on your device the file for me is in "my docs" on my Tilt.
2) Run kaiser-HardSPL from your PC with your device hooked up via usb with the green act sync icon. Once you get to the white screen of death on you device, stop unplug you device and soft boot it via your stylus and the reset button. Leave your pc alone right where it stopped in the kaiser-hardspl screen. "should be to the point where it says unplug and replug in your usb you should have the tri color screen press enter to proceed"
3) Now set your connection settings in active sync to not allow usb connections.
4) Now plug you device by in via usb and run Jumpspl1.56-kais on your device. When it has the tri color screen and says usb, unplug usb and plug back in.
5) Now back in the kaiser-hardspl window, continue on with the on screen directions. This should now install hardspl just like the rom or roms that you might have already installed and will say finished.
6) The device should reboot.
7) close the kaiser-hardspl window and let you device fully reboot.
8) Once it is fully rebooted follow these directions: Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up
9)Now run your radio update and it should go through without erroring out at 99%. It will stay at 99% for a bit then jump to 100% success!
My Tilt is working great now with sound and everything. Have not tested anything else yet, came right here and started to let you know what I did to get radio installed.
So now I'm running Duttys WM6.1 newest release with radio 1.64.06.
Call me crazy and sure I know I might have taken more steps than I needed to, but I got it working.
Hope this helps you.
Take care,
JMan
First, are you using a 6.0 rom or a 6.1 rom? If you are using a 6.0 rom you cannot flash any of the 6.1 radios and vice versa. Also, if you have hardspl installed, why would you need to use jumpspl. I have never used jumpspl and I promise I have flashed 50+ times counting, roms, radios and splash screens.
I believe that was my problem, I was never able to get Hard-spl installed and I was using jumpspl to install the 2 roms that I have installed since I got my tilt a week ago. The method I used above allowed me to get hard-spl installed and then I was able to install the radio rom. I am using Duttys WM6.1 rom.
JMan I want your babies!!!
Ok I had actually done everything upto the final step (holding the camera button after a soft reset) but that made it possible to flash the radio just as you described.
So many thanks for sharing your solution!!
Alex
jmandss said:
Hey Alex! I figured it out Brother! Do this and you should be able to upgrade your radio. I was using JumpSPL1.56-KAIS run from my device and I was running into the same problem everytime I tried to upgrade my radio. Would get to 99% and then would error out. So I followed these steps taken from a number of different post and put together until it worked!
1) Make sure you have JumpSPL1.56-KAIS somewhere on your device the file for me is in "my docs" on my Tilt.
2) Run kaiser-HardSPL from your PC with your device hooked up via usb with the green act sync icon. Once you get to the white screen of death on you device, stop unplug you device and soft boot it via your stylus and the reset button. Leave your pc alone right where it stopped in the kaiser-hardspl screen. "should be to the point where it says unplug and replug in your usb you should have the tri color screen press enter to proceed"
3) Now set your connection settings in active sync to not allow usb connections.
4) Now plug you device by in via usb and run Jumpspl1.56-kais on your device. When it has the tri color screen and says usb, unplug usb and plug back in.
5) Now back in the kaiser-hardspl window, continue on with the on screen directions. This should now install hardspl just like the rom or roms that you might have already installed and will say finished.
6) The device should reboot.
7) close the kaiser-hardspl window and let you device fully reboot.
8) Once it is fully rebooted follow these directions: Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up
9)Now run your radio update and it should go through without erroring out at 99%. It will stay at 99% for a bit then jump to 100% success!
My Tilt is working great now with sound and everything. Have not tested anything else yet, came right here and started to let you know what I did to get radio installed.
So now I'm running Duttys WM6.1 newest release with radio 1.64.06.
Call me crazy and sure I know I might have taken more steps than I needed to, but I got it working.
Hope this helps you.
Take care,
JMan
Click to expand...
Click to collapse
You are the STAR! Trillions of thanks. Solve my problem!!!
I love it when when the new guy can help out! Glad it worked guys, and thanks to all the old pros around here for allowing us to read so we can try and help ourselves out.
Take care,
JMan
I think I have fallen in love with this thread. This is truly nice to see guys. Keep up the great work.
i've the same problem, but when reboot Appear immediately hardspl, but i can't re-install nothing !
please help me
I don't want to miss mi tytn
pedro_se_rooot said:
i've the same problem, but when reboot Appear immediately hardspl, but i can't re-install nothing !
Click to expand...
Click to collapse
You need to use MTTY to get things going for you again, here is the thread to get mtty:
http://forum.xda-developers.com/showthread.php?t=371154&highlight=mtty
Search around and see if you can find the step by step to use it, might even be a how to text file in the zip file not sure. This should get you back on your way.
Can someone locate the step by step to use mtty for this man and put it in this post?
Have a good one,
JMan
Not a good day for the Wolfpack, Damn Tarheels!!
Hi all(be kind I am over 50 and a newbie)
I have been looking in these forums for some time while
I save up the cash for my S710.
Well I just got a Vodafone V1415 and I love it but I hate the vodafone
splash screens when you turn it on and there wall paper.
So I would like to flash my V1415 with a rom off here, my V1415 is not unlocked
and I understand by doing this it still wont be.
Could some kind person please put me right if what I need to do is wrong please.
1, I need to do what the guy says here
http://forum.xda-developers.com/showthread.php?t=330909
2, Then flash the chosen rom I was thinking of this rom
http://forum.xda-developers.com/showthread.php?t=414416
The kind gentelman says it is WM6.1?
would it have all the extras WM6.1 has over WM6.0?
if anyone thinks/advise me on a diffrent rom that would be nice
Thanks
deuse
PS thanks for a great site
EDIT= I have no storage card is this ok?
Hi.
I am also new to this kind of thing, but I'll try and explain it a bit better than it is there.....
Do a hard reset first, switch phone off, then while pressing and keeping pressed, the two soft keys (above 1+3 keys), switch on until promted, then press the green call key, and wait for it to finish.
1. Download and run SDA_ApplicationUnlock.zip from the computer, follow instructions until reboot.
2. Download Vox USPL- CID BYPASS.zip, once extracted run "uspl_116_jockyw", follow insructions, which is just pressing any key, until it asks if you want to run mitty or "RUU", and stop there.
3. You should have already downloaded WM6.1 CLEAN v1.4, and it is the "FLASH" program in that folder you need to run from the computer, follow instructions and you're done.
I've only just put the same on 5 mins, and wrote this while waiting for it to load.
Happy flashing!
Thank you very much I will try what you said now
Hope i dont make a mess of it
Well after a few trys it worked
The first time I got a linux screen and it would not flash?
2nd time I let the uspl_116_jockyw run till the end by pressing Y
it went to a multi color screen and flashed
I am very pleased with the result
thanks.
Hey guys looks like a bricked my 2 week old Sprint Touch Pro 2. I can't get pass the touch pro 2 logo screen now and I'm very upset with myself. Is there a way to possible unbrick the phone. I tried to sync it with my PC no response. Also i did back it up with " Microsoft My Phone " earlier in the day and its backed up on WMDManager too. I will try to take it to sprint for warranty and see what the will do. HAPPY NEW YEAR people!!
clariceave said:
Hey guys looks like a bricked my 2 week old Sprint Touch Pro 2. I can't get pass the touch pro 2 logo screen now and I'm very upset with myself. Is there a way to possible unbrick the phone. I tried to sync it with my PC no response. Also i did back it up with " Microsoft My Phone " earlier in the day and its backed up on WMDManager too. I will try to take it to sprint for warranty and see what the will do. HAPPY NEW YEAR people!!
Click to expand...
Click to collapse
Depending on what happened, it's a yes/no situation. What did you do?
Try this:
get into bootloader mode (tri-color screen): Take out the battery for one minute. Put it back in. Getting into bootloader mode is done by holding the Volume down button while you do a press/release of the Reset button. OR hold the Volume down button while you do a press/release of the Power button.
That should get you to bootloader mode. Now, plug in your USB to the PC. Flash a CDMA ROM from there by running the .exe. If you cannot do that, transfer the .nbh file (rename it to "RHODIMG.nbh" [no quotes]) and follow these instructions.
Good luck, and happy new year!
*The majority of the CDMA ROMs can be found at PPCGeeks*
PLEASE HELP ME UNBRICK MY TOUCH PRO 2 (tmobile)
i was installing a ROM onto my TP2 but i accidentally installed a CDMA ROM instead of a GSM ROM. My phone loads past the TP2 startup screen but then stays white with the rom info on the bottom. I tried to do the bootlegger with the 4 colors on the screen but it doesnt work. Also tried a hard reset. CAN SOMEONE PLS PLS PLS HELP? thanks
foxxyroxy5 said:
i was installing a ROM onto my TP2 but i accidentally installed a CDMA ROM instead of a GSM ROM. My phone loads past the TP2 startup screen but then stays white with the rom info on the bottom. I tried to do the bootlegger with the 4 colors on the screen but it doesnt work. Also tried a hard reset. CAN SOMEONE PLS PLS PLS HELP? thanks
Click to expand...
Click to collapse
Well, this forum is for CDMA TP2s, but I'll help.
So you took out the battery for at least one minute? Then you put it back in. Get into bootloader mode (T-Mobile version: phone is off, hold the Volume Down button while you press/release the Power Button. Keep holding the Volume Down button until the colorful screen shows up).
When you're in bootloader, plug in your TP2 to your PC. Now run the .exe of a GSM ROM and follow the steps, as if your phone is synced to the PC. (aka flash as you would usually do).
To flash via the Storage Card: On your PC, go to Start > My Computer > Removable Disk drive (something like that; make sure this is your phone's Storage Card). Drag the .nbh of a GSM ROM there. Rename the .nbh "RHODIMG.nbh" (no quotes). Unplug your Phone. Take out the battery again for one minute. Now, go back into bootloader (hold Volume Down button and press/release Power button [keep holding the Volume Down button]). Follow the steps to flash the phone.
Good luck.
RE:LEASE HELP ME UNBRICK MY TOUCH PRO 2 (tmobile)
Thank you very much for helping me with my TP2 problem! You were my last resort and i was going to give up. It works perfectly fine! I really really appreciate it! THANK YOU AGAIN
Should work
foxxyroxy5 said:
i was installing a ROM onto my TP2 but i accidentally installed a CDMA ROM instead of a GSM ROM. My phone loads past the TP2 startup screen but then stays white with the rom info on the bottom. I tried to do the bootlegger with the 4 colors on the screen but it doesnt work. Also tried a hard reset. CAN SOMEONE PLS PLS PLS HELP? thanks
Click to expand...
Click to collapse
You did exactly the reverse of what I did, and the instructions already given are how I resolved it: put it in bootloader and flash a compatible ROM. I flashed a stock ROM just to be sure, but that's probably not needed.
foxxyroxy5 said:
Thank you very much for helping me with my TP2 problem! You were my last resort and i was going to give up. It works perfectly fine! I really really appreciate it! THANK YOU AGAIN
Click to expand...
Click to collapse
No problem. Enjoy your unbricked TP2 this new year!
Bricked my Sprint Touch Pro 2
i downloaded a hotfix for internal gps from htc website for Sprint touch pro 2. after i tried to install it the phone went off and now it won't even power on or go to boot loader.. any suggestions on how i can fix this i was using Mighty Rom 6.5 with htc sense 2.1
[email protected] said:
i downloaded a hotfix for internal gps from htc website for Sprint touch pro 2. after i tried to install it the phone went off and now it won't even power on or go to boot loader.. any suggestions on how i can fix this i was using Mighty Rom 6.5 with htc sense 2.1
Click to expand...
Click to collapse
See if you can do a hard-reset right now. While phone is off (which it is), press and hold Talk/Send, End, and Power button at the same time. Wait for a screen to pop-up. Follow steps to hard reset. That will bring it back to factory defaults.
If it doesn't work, maybe you could post your question on PPCGeeks, where a lot of CDMA people go. They might be able to help you.
Can you Unbrick a Touch Pro 2
Hi to all,
I'm a new here and a little desperate . I flashed my rom by using a raphael update instead of Rhodium. My phone got bricked. My phone is a Sprint HTC touch pro 2.
At the moment, it will not boot, when I plug it to my computer and it was looking for qualcomm cdma MSM drivers.
I tried sof and hardware reset including the boot loader. Nothing works. I also tried using different RUUs. Nothing works. I hope somebody can help me.
Fixed the problem...bought an android...ha,ha...
smileyzst said:
The same exact thing happened to my tp2.Accidently flashed touch pro(RAPHEL)rom and now nothing!!It won't power on or anything,can someone help me too...Is my phone bricked???? Help please!!!
Click to expand...
Click to collapse
Well if you can power it on, and go to bootloader, then your phone is just fine. Just flash a Rhodium ROM.
I suggest take battery out, and put it back in after few seconds, to see if it powers on. If not, leave it in the charger, and see if it powers on.
After installing the HardSPL, I decided to flash my US Cellular CDMA phone with a GSM rom and of course it bricked it. The phone would only boot to bootloader, so I was going to have it repaired for $70. But if I was willing to flash my device, then I'm sure as willing to look for a DIY solution somewhere. Goodthing I searched this forum, because the answers where right here!
Just format your microSD to FAT32, install an extracted stock ROM kit to the root of the SD insuring you rename the .nbh to RHODMIG.nbh and place the other extracted files on the SD as well. Place the microSD in your HTC Touch Pro2 and boot to bootloader. You may have to take steps to get to the bootloader, mine booted to bootloader automatically anyway at that point. Follow onscreen instructions, and your Touch will be as good as new!
thanks a million for helping me unbrick my tp2
wow man thanks a million, i followed the instru and it worked but was slow so i did task 29 and flashed the rom i wanted and it works great, i really appreciate your help on this
How did you get to the bootloader menu. I am using CDMA HTC Pro 2 by Sprint. Thanks
goldenu said:
You did exactly the reverse of what I did, and the instructions already given are how I resolved it: put it in bootloader and flash a compatible ROM. I flashed a stock ROM just to be sure, but that's probably not needed.
Click to expand...
Click to collapse
@rocco24
Did everything go alright? If not, just post here or send me a PM.
Hi i have a different issue I accidentally flashed the wrong nv items 01192 and now its rebooting. if someone can dump their tp2 sprint 6.5 nv items please help. I am cut off from the world of cell phones at the time. I read that i also would need the radio dump which in my case is the same one on the 6.5 ruu windows version. any feed back or advice is welcome. please help guys.
Oscar
sumflipnol said:
Well, this forum is for CDMA TP2s, but I'll help.
So you took out the battery for at least one minute? Then you put it back in. Get into bootloader mode (T-Mobile version: phone is off, hold the Volume Down button while you press/release the Power Button. Keep holding the Volume Down button until the colorful screen shows up).
When you're in bootloader, plug in your TP2 to your PC. Now run the .exe of a GSM ROM and follow the steps, as if your phone is synced to the PC. (aka flash as you would usually do).
To flash via the Storage Card: On your PC, go to Start > My Computer > Removable Disk drive (something like that; make sure this is your phone's Storage Card). Drag the .nbh of a GSM ROM there. Rename the .nbh "RHODIMG.nbh" (no quotes). Unplug your Phone. Take out the battery again for one minute. Now, go back into bootloader (hold Volume Down button and press/release Power button [keep holding the Volume Down button]). Follow the steps to flash the phone.
Good luck.
Click to expand...
Click to collapse
I wonder if you can help me; i have a sprint hybrid cdma/gsm and it has black screen no lights at all but the qualcomm cpu is easily recognized by pc-have tried all known methods to get in bootloader but i get no lights at all??-have fully charged batt from another tp2=any experience w this problem?-thanks
keeps rebooting?
Hello, I'm wondering if anyone has experienced the problem I'm facing:
I have the latest Energy rom, with Android 2.3 on SD card. Android proved to be quite unstable and requires soft resets every now and then. Most of the time I would let it boot into WinMo and then run Haret again to get into Android.
Yesterday I left in running in Android all day, and in the evening I noticed the phone had died. Thinking it was just out of battery, I just plugged it in, let it charge for a few hours, then tried to boot it up. But it just kept rebooting, never getting pass the Touch Pro 2 boot screen.
Did hard resets twice, same thing. Re-flash the rom, same thing. Took out SD card, flashed again, same thing. Everything I tried, it would not get pass the initial boot screen, and just cycles the reboot again. Oh by the way, the hard resets and re-flashes are all successful with no errors.
Anyone have a solution to this? Thanks!
velo25 said:
Hello, I'm wondering if anyone has experienced the problem I'm facing:
I have the latest Energy rom, with Android 2.3 on SD card. Android proved to be quite unstable and requires soft resets every now and then. Most of the time I would let it boot into WinMo and then run Haret again to get into Android.
Yesterday I left in running in Android all day, and in the evening I noticed the phone had died. Thinking it was just out of battery, I just plugged it in, let it charge for a few hours, then tried to boot it up. But it just kept rebooting, never getting pass the Touch Pro 2 boot screen.
Did hard resets twice, same thing. Re-flash the rom, same thing. Took out SD card, flashed again, same thing. Everything I tried, it would not get pass the initial boot screen, and just cycles the reboot again. Oh by the way, the hard resets and re-flashes are all successful with no errors.
Anyone have a solution to this? Thanks!
Click to expand...
Click to collapse
Try flashing another ROM or try putting in another battery and see if the bootloop issue goes away. Kindly update the status of your post if you fixed the issue or are still having problems.
Ok. I've had problems up and down and tried and tried to do this and finally got it. So now I'm going to share it with all of you.
1. Download and Unzip the Files in the thread for the Ozone Verizon (HardSPL) posted by JockyW.
http://forum.xda-developers.com/showthread.php?t=551458
2. Connect your phone via ActiveSync, let it sync, and then start the auto.bat.
3. First, the JumpSPL will copy over. Press enter on the computer. Then the SSPL will copy over. Press Enter on the computer. Then it will prompt to start the JumpSPL. Press Enter. JumpSPL should pop up on your phone. Press the silver center button to start JumpSPL. The screen goes black. Then the DOS window will ask you if you have USB Connectivity. DO NOT PRESS ENTER YET!!!!
4. THIS IS VERY IMPORTANT!!! Wait for your phone to disconnect from ActiveSync. Once it does, unplug your phone from the USB. Go into ActiveSync's Connection Settings, and uncheck the box that says ALLOW USB CONNECTIONS. Reconnect your phone to the USB, and it should install the HTC USB Sync driver. NOW PRESS ENTER IN THE DOS WINDOW.
5. The RomUpdateUtility will start up, run it. And it should do the HardSPL on your phone. Your phone will restart when it's finished. If you want to check, before you do any of the above steps, copy the EnterBootloader.exe over to your phone. When you're done with the RomUpdateUtility and the phone has restarted, run the Bootloader and see what the tricolor screen says. It should be 0.39 Hard. Pull the battery, put it back in, restart the phone, and you should be good to go for flashing custom roms!
WOOHOO!
Thanks guys! I'll be donating soon. I'm about to flash the custom 3VO ROM right now! I'll let you know how it goes!
::EDIT:: The 3VO ROM is beautiful and runs like a charm! You guys put so much work into this.
Let it be known that this method for flashing the HardSPL can also be used for flashing the 3VO ROM.
NOTE: I WILL NOT TAKE RESPONSIBILITY FOR BRICKING YOUR PHONE.... seeing as I was scared I almost bricked mine once, and was VERY LUCKY that I did not. Please, follow all directions carefully. Phones are expensive.
ActiveSyn Doesn't disconnect
I got to the step where JumpSPL runs and my screen goes black. However, my phone never disconnects from ActiveSync. I tried unplugging it and disabling USB in activesync, but then my phone comes up as Not Recognized. If I try to run JumpSPL at this point I get, "Error (260): Connection." Any ideas?
How long are you waiting for ActiveSync to disconnect? It takes awhile. I know for me, it took about 5-10 minutes for it to disconnect.
Try waiting a little bit longer, and let us know what happens.
I waited long enough for activesync to stop. I unplugged my phone, disabled USB in activesync, and reconnected my phone. Every time I get a error saying "USB Device Not Recognized." If I try to run the update utility I get a connection error.
In all fairness I bricked my phone initially and had to recover it using a "stock" ROM someone posted for the CEDAR. My phone might just be hosed.
wm 6.5
quick question, the only way i was able to unbrick my phone was by upgrading it to the wm6.5 rom by Verzion, will the HardSPL work with this one?
I flashed the HardSPL on the Verizon 6.5 Update. So I guess the answer would be Yes.
I'm really lovin' this 3VO ROM. It's fast and the battery last a lot longer.
i tried your method and i'm still coming up with SPL-0.39.0000
i've tried other peoples guides as well and cant get it to hardspl, any ideas?
I followed all of these steps a few different times and my Bootloader still says .44. I tried varying the steps a little based on what users said on the thread about putting the HardSPL on the .39 and it still didn't help. I'm going to keep trying various configurations, but if anyone else is able to get their Official 6.5 ROM over to the 3VO, I'd love to hear how.
Thanks
what i need to know is what is hardspl i have an ozone that is unlocked but the data area is still locked to verizson and thats why i need to flash so i need to know what is hardspl and if its needed for an unlocked ozone
recoshaa said:
what i need to know is what is hardspl i have an ozone that is unlocked but the data area is still locked to verizson and thats why i need to flash so i need to know what is hardspl and if its needed for an unlocked ozone
Click to expand...
Click to collapse
You can find the hardspl definition here http://forum.xda-developers.com/wiki/index.php?title=Glossary
If you want to install a custom rom you will need to hardspl your device.
I hope that helps
I ran auto.bat, when the updater failed I disconnected USB from phone, reconnected, then ran updater manually and it all worked. Had to do this on both the HSPL and the ROM.
Also, make sure you don't uncompress both to same folder as it creates a .nbh file and if you have both on same folder you might be trying to install the ROM instead of the HSPL or vice-versa.
Another note. If you are HSPL already you can turn off device, turn it back on pressing DOWN VOLUME and POWER, leave both pressed until you get to rainbow screen, you can then run the updater and it won't bug you with battery being less than 1/2
I had problem that after screen goes blank, the phone will not connect. Some time "HTC USb Sync" will show, some time not. ROM Update will always complain that phone was not connected.
This is what I did to solve.
1. Power Off.
2. Hold vol dn and send with one hand. Then power with other hand.
3. Choose restore default configuration.
4. Let it boot
5. connect to ActiveSync.
6. Now run auto.bat
7. It runs fine and HArd SPL is loaded.
Enjoy.
schoenkn2 said:
quick question, the only way i was able to unbrick my phone was by upgrading it to the wm6.5 rom by Verzion, will the HardSPL work with this one?
Click to expand...
Click to collapse
Hi there, not sure if this belongs here. If you're planning on putting a custom ROM on the Verizon Ozone, do not use the HTC/Verizon wm6.5 update! "!! DO NOT !!" With the original stock wm6.1, you have a .39 Bootloader. After flashing the HTC/Verizon wm6.5 Stock Rom, you have a .44 Bootloader. And you can forget about putting a Custom/3rd Party ROMS. If somebody knows how to fix this, please tell me.
Thanks, and enjoy your HTC!
JD
Hi, i must be the dumbest person in here. I just bricked my used sprint touch pro 2. Well it all started when i did not get any sleep, and did not paying attention. My phone was fully unlocked. So i decided i could not wait to flash my phone. So i started to flash the phone, but after it was done i realized i only flashed the BLEEPING SPLASH SCREEN !!!!!!!!
So when i tried to turn the phone on, it loads to the splash screen only.
So i tried to connect it to my computer, but nothing. So i tried to hard reset, it goes to bootloader screen, then only to Touch pro 2 screen. Is there anything that i could do beside Cry, lol. HELP PLEASE.
Can you enter bootloader on your touch pro2?
If so, then its good news and its not bricked Download an official rom from HTC website (or here from the touch pro 2 forum), connect it to your computer whilst in bootloader (multi coloured screen) - make sure is says usb and not serial on ur devices screen and double click your downloaded rom.
It should flash succesfully and you will have your device back up and running in under 10 minutes.
Good luck.
Maybe i should elaborate more. when i said, when i connect it to the computer nothing. I meant nothing happens. Meaning it does not connect, or recognize the Usb, or computer. Help, THX
Ok, you know how to get ur device into bootloader right? what does it say on the screen (dont bother connecting it to your computer).
It jumps right from bootloader mode to the screen that ask me if i want reset all setting to manufacturer default, or cancel page.
soft reset = hold the power button and the volume button down and softreset
I think you are trying to to a hard reset
If you can stay in bootloader, it is possible to flash official stock rom from your sd card. It isnt too difficult to do so let me know and ill tell you how to do it, but have a look on the touch pro 2 forum, you will find how to do it there
Okay, i did a soft reset. And it is staying at the boot loader screen. So it is possible to fix this sprint phone?
Okay, i think i have an idea what you want me to do. You want me to put the phone in boot loader mode, then down load a .nbh file onto the root of the SD card. And while in boot loader mode it should flash the stock rom.
Is that correct?
Yes exactly that
Make sure you extract the nbh file from the stock rom using winzip or another utility. You must then rename it to something like xxxxx.nbh (you will need to get this from the tp2 forum or when i have time ill find it for u). COpy it to the root as you say, enter bootloader etc etc.
You will find how to do this in the tp2 forum.
Good luck.
Once you get into the bootloader (the tri-coloured screen) it should say "Serial" at the bottom. Then plug the USB cable in from your PC, and that should change to "USB".
If it does say "USB", then you should be able to go ahead and flash a ROM from the PC (no need to do it via SD unless you really want to). You don't need an ActiveSync connection.
Omg. I love you guys. You guys are the best in the whole amm world. I will be donating shortly. Thank you so much. It worked perfectly in boot loader mode to connect it to the usb. Than i was able to download the stock rom.
Now should i hard reset it or just leave it alone. Thanks a million.
Hey, good news.
I guess when you said before that it didn't say usb whilst in bootloader was because you weren't actually in bootloader no matter.
Glad you got it back up and running without having to flash via sd
If you flashed an official stock rom, don't bother hard resetting, no point, if you flashed a custom or cooked rom then normally advisable to HR after a flash but this does depend on the rom.
Cheers.