Ok. I've had problems up and down and tried and tried to do this and finally got it. So now I'm going to share it with all of you.
1. Download and Unzip the Files in the thread for the Ozone Verizon (HardSPL) posted by JockyW.
http://forum.xda-developers.com/showthread.php?t=551458
2. Connect your phone via ActiveSync, let it sync, and then start the auto.bat.
3. First, the JumpSPL will copy over. Press enter on the computer. Then the SSPL will copy over. Press Enter on the computer. Then it will prompt to start the JumpSPL. Press Enter. JumpSPL should pop up on your phone. Press the silver center button to start JumpSPL. The screen goes black. Then the DOS window will ask you if you have USB Connectivity. DO NOT PRESS ENTER YET!!!!
4. THIS IS VERY IMPORTANT!!! Wait for your phone to disconnect from ActiveSync. Once it does, unplug your phone from the USB. Go into ActiveSync's Connection Settings, and uncheck the box that says ALLOW USB CONNECTIONS. Reconnect your phone to the USB, and it should install the HTC USB Sync driver. NOW PRESS ENTER IN THE DOS WINDOW.
5. The RomUpdateUtility will start up, run it. And it should do the HardSPL on your phone. Your phone will restart when it's finished. If you want to check, before you do any of the above steps, copy the EnterBootloader.exe over to your phone. When you're done with the RomUpdateUtility and the phone has restarted, run the Bootloader and see what the tricolor screen says. It should be 0.39 Hard. Pull the battery, put it back in, restart the phone, and you should be good to go for flashing custom roms!
WOOHOO!
Thanks guys! I'll be donating soon. I'm about to flash the custom 3VO ROM right now! I'll let you know how it goes!
::EDIT:: The 3VO ROM is beautiful and runs like a charm! You guys put so much work into this.
Let it be known that this method for flashing the HardSPL can also be used for flashing the 3VO ROM.
NOTE: I WILL NOT TAKE RESPONSIBILITY FOR BRICKING YOUR PHONE.... seeing as I was scared I almost bricked mine once, and was VERY LUCKY that I did not. Please, follow all directions carefully. Phones are expensive.
ActiveSyn Doesn't disconnect
I got to the step where JumpSPL runs and my screen goes black. However, my phone never disconnects from ActiveSync. I tried unplugging it and disabling USB in activesync, but then my phone comes up as Not Recognized. If I try to run JumpSPL at this point I get, "Error (260): Connection." Any ideas?
How long are you waiting for ActiveSync to disconnect? It takes awhile. I know for me, it took about 5-10 minutes for it to disconnect.
Try waiting a little bit longer, and let us know what happens.
I waited long enough for activesync to stop. I unplugged my phone, disabled USB in activesync, and reconnected my phone. Every time I get a error saying "USB Device Not Recognized." If I try to run the update utility I get a connection error.
In all fairness I bricked my phone initially and had to recover it using a "stock" ROM someone posted for the CEDAR. My phone might just be hosed.
wm 6.5
quick question, the only way i was able to unbrick my phone was by upgrading it to the wm6.5 rom by Verzion, will the HardSPL work with this one?
I flashed the HardSPL on the Verizon 6.5 Update. So I guess the answer would be Yes.
I'm really lovin' this 3VO ROM. It's fast and the battery last a lot longer.
i tried your method and i'm still coming up with SPL-0.39.0000
i've tried other peoples guides as well and cant get it to hardspl, any ideas?
I followed all of these steps a few different times and my Bootloader still says .44. I tried varying the steps a little based on what users said on the thread about putting the HardSPL on the .39 and it still didn't help. I'm going to keep trying various configurations, but if anyone else is able to get their Official 6.5 ROM over to the 3VO, I'd love to hear how.
Thanks
what i need to know is what is hardspl i have an ozone that is unlocked but the data area is still locked to verizson and thats why i need to flash so i need to know what is hardspl and if its needed for an unlocked ozone
recoshaa said:
what i need to know is what is hardspl i have an ozone that is unlocked but the data area is still locked to verizson and thats why i need to flash so i need to know what is hardspl and if its needed for an unlocked ozone
Click to expand...
Click to collapse
You can find the hardspl definition here http://forum.xda-developers.com/wiki/index.php?title=Glossary
If you want to install a custom rom you will need to hardspl your device.
I hope that helps
I ran auto.bat, when the updater failed I disconnected USB from phone, reconnected, then ran updater manually and it all worked. Had to do this on both the HSPL and the ROM.
Also, make sure you don't uncompress both to same folder as it creates a .nbh file and if you have both on same folder you might be trying to install the ROM instead of the HSPL or vice-versa.
Another note. If you are HSPL already you can turn off device, turn it back on pressing DOWN VOLUME and POWER, leave both pressed until you get to rainbow screen, you can then run the updater and it won't bug you with battery being less than 1/2
I had problem that after screen goes blank, the phone will not connect. Some time "HTC USb Sync" will show, some time not. ROM Update will always complain that phone was not connected.
This is what I did to solve.
1. Power Off.
2. Hold vol dn and send with one hand. Then power with other hand.
3. Choose restore default configuration.
4. Let it boot
5. connect to ActiveSync.
6. Now run auto.bat
7. It runs fine and HArd SPL is loaded.
Enjoy.
schoenkn2 said:
quick question, the only way i was able to unbrick my phone was by upgrading it to the wm6.5 rom by Verzion, will the HardSPL work with this one?
Click to expand...
Click to collapse
Hi there, not sure if this belongs here. If you're planning on putting a custom ROM on the Verizon Ozone, do not use the HTC/Verizon wm6.5 update! "!! DO NOT !!" With the original stock wm6.1, you have a .39 Bootloader. After flashing the HTC/Verizon wm6.5 Stock Rom, you have a .44 Bootloader. And you can forget about putting a Custom/3rd Party ROMS. If somebody knows how to fix this, please tell me.
Thanks, and enjoy your HTC!
JD
Related
Hi, help please...
I have Wizard G3 with TNT 5 Touch Flow and tried to update radio T-mobile UK 2.19 Radio Only. update went OK but now on loading I see HTC boot screen then it moves to TNT 5.0 screen and then fades in two minutes and starts back with HTC boot screen. It then circulates like that for ever without passing to the Today screen. On connection with PC for new update with any rom it shows: Error (260) update error. What can be done?
denflorida said:
Hi, help please...
I have Wizard G3 with TNT 5 Touch Flow and tried to update radio T-mobile UK 2.19 Radio Only. update went OK but now on loading I see HTC boot screen then it moves to TNT 5.0 screen and then fades in two minutes and starts back with HTC boot screen. It then circulates like that for ever without passing to the Today screen. On connection with PC for new update with any rom it shows: Error (260) update error. What can be done?
Click to expand...
Click to collapse
it's a case of bad flash,did anything during flash happened like lose usb connectivity,pc crashed,battery discharged or something like unusual ?
Try to soft reset and see if it works,otherwise you'll have to reflash to official carrier's rom in boodloader mode,
1. Disconnect your phone from the usb cable,shut down any firewall,disable any Anti virus,Reboot your PC.
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. On your PC Open windows Task Manager...>Tab Processes...>wescomm.exe...>End process
4. Power off the phone completely (Not stand-by,shut off completely),or you may take the battery out for few seconds
5. Make sure your phone is not Connected to the PC via USB cable and remove the dummy Sdcard or mini-Sd card
6. Get your phone into Bootloader mode (Multicolor screen) by pressing camera button + Power on button
7. Reconnect your phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Be sure that your battery is charged over 70%)
8. "USB"will appear on the bottom of the screen of the Bootloader (Multicolor screen)
9. Run the Upgrade again and it will work fine without any problems.
10.Never use Bluetooth sync for the Upgrade
While upgrading, the ActiveSync program will not go on, however the upgrade is running.Please be patient when you're flashing your device, even if 98%. It can wait a little bit, 5 ~ 7 minutes.
Don't cancell the flash or get the phone off the usb cable till it confirms "Congratulations" or stops with an Error!!!
Hope it'll work, Good luck
Hi, this is the first time i saw a Paki guy on this web. I know there is alot of talent in IT profession in Pakistan. Anyway its good to see u here and i got a relief that with the help of a senior member like you i can get my phone work again.
To cut the chase, I have X01HT by Softbank Japan. It is Herms200 by HTC Japanese WM5 ROM. I have installed Asukal's English MUI and it was working fine for me. Now i'm planning to visit Pakistan this month so i though to unlock the sim and i used Prof v3a to unlock. I've successfully unlocked the sim and i guess CID also. When i use some other carrier's sim, i can receive the calls but cant make the calls out coz Softbank rom has a security which comes at screen and ask for password and dont let me do anything on the PDA. After studying alot on this forum i figured that i need to change the rom to get rid of that password message. i used the Olipro's Hard SPL and got bootloader 2.10 Olipro. I checked the other necessary stuff and when satisfied i started rom update. I end up with the same message of Error 260. Now my phone has no OS and it starts at bootloader. i tried everything possible like i make sure to remove all firewalls on my PC, used all the versions of Activesync and everything possible that i could. I trust that there is nothing wrong with the ROM etc but it is with connection.
Now if i update to the original ROM, i'm afraid that it will also upgrade my Bootloader and could never be able to flash english rom. I'm really depressed for the last three days and loosing sleep as well. I trust that you or any other senior member can help me with this.
Thanks in advance and looking forward anxiously.
Farrukh, wrong forum.
You know you have a Hermes, then you should know to post your questions in Hermes related forum, not wizard.
denflorida:
Try to update other Radio-only ROMs in xda's FTP server.
Sorry Brother, i know i have herms but i couldn't find some related topic in herms and i figured that Activesync problem is the same in all devices.
Anyway, thanks for the prompt reply. I'll try to find some from Herms.
Thanks
8125 rom update
i have tried to do a rom update on my 8125 g4. i recently purchased it off ebay and i have two problems. the reason i want to update it is because when i try to enable the wifi my device freezes. the other problem is that i can not seem to get the phone into boot loader mode. i have tried :
-turning the phone off and holding the camera button as i turn it on.
-holding the camera button and pluging it in to a usb port.
- using wizard service tool to enter boot loader mode.
after each of these different attempts i had to either remove the battery for 3 secs or hold the reset button for a few seconds before i can turn it back on. the phone still turns and just i can not use the wifi
Yes!!! Thank you! your instructions worked for me and got me past the Error [260] with my 8125 .
zabardast_1 said:
it's a case of bad flash,did anything during flash happened like lose usb connectivity,pc crashed,battery discharged or something like unusual ?
Try to soft reset and see if it works,otherwise you'll have to reflash to official carrier's rom in boodloader mode,
Click to expand...
Click to collapse
Thanks! Worked for Topaz and latest radio update.
OK
I've always had troubles flashing radios for some reason, I've managed to just not do it but now with Duttys 6.1 out I really need some help
- I've flashed Duttys latest successfully
- I've flashed HardSPL
- But whenever I flash the radio (1.64.08.21) I get a connection error at 99%!!
Now I can still get into the phone using mtty and the boot command.
Am I doing something stupid -- Any help gratefully received!
Alex
ps - I have a UK o2 XDA Stellar
I'm a newbie been here with a AT&T Tilt less than a week and I promise I'm reading, but I'm having the exact same problem. Flashed Duttys dual V4 as my first try last Tuesday without a problem and of course be a crazy new guy I wanted his newest work. So I flashed Duttys 6.1 today and I guess I just can't figure out how to flash radios, because I've tried 2 now and both error out at 99% and I too have to use mtty to get back into the phone. I'll keep reading, but if someone could tell us new guys what the heck we are doing wrong that would be great.
PS I'm glad to be here and this looks like a lot on fun thanks for having me and look forward to helping out someday.
JMan
Hey Alex! I figured it out Brother! Do this and you should be able to upgrade your radio. I was using JumpSPL1.56-KAIS run from my device and I was running into the same problem everytime I tried to upgrade my radio. Would get to 99% and then would error out. So I followed these steps taken from a number of different post and put together until it worked!
1) Make sure you have JumpSPL1.56-KAIS somewhere on your device the file for me is in "my docs" on my Tilt.
2) Run kaiser-HardSPL from your PC with your device hooked up via usb with the green act sync icon. Once you get to the white screen of death on you device, stop unplug you device and soft boot it via your stylus and the reset button. Leave your pc alone right where it stopped in the kaiser-hardspl screen. "should be to the point where it says unplug and replug in your usb you should have the tri color screen press enter to proceed"
3) Now set your connection settings in active sync to not allow usb connections.
4) Now plug you device by in via usb and run Jumpspl1.56-kais on your device. When it has the tri color screen and says usb, unplug usb and plug back in.
5) Now back in the kaiser-hardspl window, continue on with the on screen directions. This should now install hardspl just like the rom or roms that you might have already installed and will say finished.
6) The device should reboot.
7) close the kaiser-hardspl window and let you device fully reboot.
8) Once it is fully rebooted follow these directions: Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up
9)Now run your radio update and it should go through without erroring out at 99%. It will stay at 99% for a bit then jump to 100% success!
My Tilt is working great now with sound and everything. Have not tested anything else yet, came right here and started to let you know what I did to get radio installed.
So now I'm running Duttys WM6.1 newest release with radio 1.64.06.
Call me crazy and sure I know I might have taken more steps than I needed to, but I got it working.
Hope this helps you.
Take care,
JMan
First, are you using a 6.0 rom or a 6.1 rom? If you are using a 6.0 rom you cannot flash any of the 6.1 radios and vice versa. Also, if you have hardspl installed, why would you need to use jumpspl. I have never used jumpspl and I promise I have flashed 50+ times counting, roms, radios and splash screens.
I believe that was my problem, I was never able to get Hard-spl installed and I was using jumpspl to install the 2 roms that I have installed since I got my tilt a week ago. The method I used above allowed me to get hard-spl installed and then I was able to install the radio rom. I am using Duttys WM6.1 rom.
JMan I want your babies!!!
Ok I had actually done everything upto the final step (holding the camera button after a soft reset) but that made it possible to flash the radio just as you described.
So many thanks for sharing your solution!!
Alex
jmandss said:
Hey Alex! I figured it out Brother! Do this and you should be able to upgrade your radio. I was using JumpSPL1.56-KAIS run from my device and I was running into the same problem everytime I tried to upgrade my radio. Would get to 99% and then would error out. So I followed these steps taken from a number of different post and put together until it worked!
1) Make sure you have JumpSPL1.56-KAIS somewhere on your device the file for me is in "my docs" on my Tilt.
2) Run kaiser-HardSPL from your PC with your device hooked up via usb with the green act sync icon. Once you get to the white screen of death on you device, stop unplug you device and soft boot it via your stylus and the reset button. Leave your pc alone right where it stopped in the kaiser-hardspl screen. "should be to the point where it says unplug and replug in your usb you should have the tri color screen press enter to proceed"
3) Now set your connection settings in active sync to not allow usb connections.
4) Now plug you device by in via usb and run Jumpspl1.56-kais on your device. When it has the tri color screen and says usb, unplug usb and plug back in.
5) Now back in the kaiser-hardspl window, continue on with the on screen directions. This should now install hardspl just like the rom or roms that you might have already installed and will say finished.
6) The device should reboot.
7) close the kaiser-hardspl window and let you device fully reboot.
8) Once it is fully rebooted follow these directions: Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up
9)Now run your radio update and it should go through without erroring out at 99%. It will stay at 99% for a bit then jump to 100% success!
My Tilt is working great now with sound and everything. Have not tested anything else yet, came right here and started to let you know what I did to get radio installed.
So now I'm running Duttys WM6.1 newest release with radio 1.64.06.
Call me crazy and sure I know I might have taken more steps than I needed to, but I got it working.
Hope this helps you.
Take care,
JMan
Click to expand...
Click to collapse
You are the STAR! Trillions of thanks. Solve my problem!!!
I love it when when the new guy can help out! Glad it worked guys, and thanks to all the old pros around here for allowing us to read so we can try and help ourselves out.
Take care,
JMan
I think I have fallen in love with this thread. This is truly nice to see guys. Keep up the great work.
i've the same problem, but when reboot Appear immediately hardspl, but i can't re-install nothing !
please help me
I don't want to miss mi tytn
pedro_se_rooot said:
i've the same problem, but when reboot Appear immediately hardspl, but i can't re-install nothing !
Click to expand...
Click to collapse
You need to use MTTY to get things going for you again, here is the thread to get mtty:
http://forum.xda-developers.com/showthread.php?t=371154&highlight=mtty
Search around and see if you can find the step by step to use it, might even be a how to text file in the zip file not sure. This should get you back on your way.
Can someone locate the step by step to use mtty for this man and put it in this post?
Have a good one,
JMan
Not a good day for the Wolfpack, Damn Tarheels!!
Want to make $20 thru paypal? help me get my Tilt out of the bootloader screen!
first off, im not new here; i lurked, learned, and flashed a few roms before i really posted much of anything.
my Tilts' screen was cracked a few days back, im headed to Greece in 2 days, so i went and bought a new Tilt to replace it until the replacement screen part gets here from Hong Kong.
The new Tilt came with WM6.1 installed, first thing i did is CID unlock it with HardSPL. i kept getting the white screen, but managed to bypass it, and flashed the RynCppr V4 on it with only the aforementioned white screen issue. I also have Ruu_Signed_Duttys_WM6.1_Official_5.2.19209_1_58_16_27 [FIX] ROM, but that would not install, i kept getting comm errors (ie the installation would never get past 0%).
I would like to run Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid V2_1_65.14.06[CubeV2] as i've played around with it on a buddy's Tilt, but it too wont install past 0%; i NEVER had these problems at ALL on my old Tilt (WM6.0), it seems to be linked to the SPL, and hardSPL does not seem to be allowing me to flash anything but the RynCppr V4 ROM; im getting extremely torqued about this, please, any assistance would be appreciated.
Take a look at this post (it's in the Stickies). If you have the white screen then you need to use JumpSPL. Use 1.93.
http://forum.xda-developers.com/showthread.php?t=354061
Good luck.
ecltech said:
Take a look at this post (it's in the Stickies). If you have the white screen then you need to use JumpSPL. Use 1.93.
http://forum.xda-developers.com/showthread.php?t=354061
Good luck.
Click to expand...
Click to collapse
thanks, thats precisely how i bypassed the first white screen errors; the problem here is i can get into the bootloader, but it wont transfer and install the new ROM. i have to jump the SPL every time i want to attempt to flash a ROM. im down to about 4 hrs left of trying before i have to give up and get going lol.
You can't install a ROM using JumpSPL. Just HardSPL the device once you have run JumpSPL as per the instructions in the post and once it's HardSPLed you can install any ROM.
RynCppr worked because it's an AT&T base ROM.
use jumpspl to flash hardspl, then you can flash roms the normal way.
do not use jumpspl to flash a rom.
XtreMe_G said:
use jumpspl to flash hardspl, then you can flash roms the normal way.
do not use jumpspl to flash a rom.
Click to expand...
Click to collapse
it wont let me install HardSPL even with JumpSPL. now its stuck in the bootloader. im trying to get the OEM or the Cppr ROMS...
slade8525,
make sure you follow these steps exactly:
1a. download the 5 attached files
1b. pull out the battery and reinsert it (this step *is* important)
1c. connect your PC to phone with a USB cable
2. REMOVE SIM and SD CARDS !!
3. copy JumpSPL1.56-KAIS.exe to your device and run it (make sure the USB cable is still connected). If you still get a white screen then reset your device and now try JumpSPL1.93-KAIS.exe
4. after a few seconds "USB" appears on the phone display
5. unplug and replug the usb cable
6. deselect "Allow USB connections" in Activesync connection settings
7. now flash hardSPL (run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC)
Are you trying 1.93 or 1.56? I never had luck with 1.56 so try 1.93 if you're not.
Very important you do the steps as listed above. Any shortcuts and no go. When I was doing this on a Tilt I replaced, I kept forgetting to disable the USB connection from Active Sync and also unplug/replug the USB cable.
if anyone can walk me through getting it the HELL out of the bootloader or direct me to the correct ROM that WILL flash correctly, i'd be willing to paypal $20 ASAP.
ecltech said:
slade8525,
make sure you follow these steps exactly:
1a. download the 5 attached files
1b. pull out the battery and reinsert it (this step *is* important)
1c. connect your PC to phone with a USB cable
2. REMOVE SIM and SD CARDS !!
3. copy JumpSPL1.56-KAIS.exe to your device and run it (make sure the USB cable is still connected). If you still get a white screen then reset your device and now try JumpSPL1.93-KAIS.exe
4. after a few seconds "USB" appears on the phone display
5. unplug and replug the usb cable
6. deselect "Allow USB connections" in Activesync connection settings
7. now flash hardSPL (run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC)
Are you trying 1.93 or 1.56? I never had luck with 1.56 so try 1.93 if you're not.
Very important you do the steps as listed above. Any shortcuts and no go. When I was doing this on a Tilt I replaced, I kept forgetting to disable the USB connection from Active Sync and also unplug/replug the USB cable.
Click to expand...
Click to collapse
well, i tried that method several times now, unfortunately im now stuck in the bootloader. here is precisely what the red/green/blue/white bootloader interface says...
top left RUUNBH
top right
KAIS1*0
SPL-1.93.0000
CPLD-8
bottom (in the white band) USB (if connected to PC) Serial (if not connected to PC)
i REALLY need this damn thing operational. flashing my 'older' launch Tilt was a piece of cake. if i try to flash HardSPL (through the PC ) it gets me to the command prompt where you hit Enter, i hit it, and nothing happens. i try to flash ANY ROM and it wont get past 0% and encounters a connection error.
Flash the WM6 factory ATT Rom (do all this crap while in wm6.0)
Go to bootloader mode & confirm HardSPL....if not there, HardSPL
Once done....do the security unlock (may as well do it with wm6.0)
Go to bootloader mode and confirm Security Unlock...if confirmed ***flash back the original Radio***
You should now be HardSPL'd and Security unlocked
Flash a wm6.1 Rom w/Radio (this will skip a flash)
You now have to flash one of the JumpSPL's....since you have a new device, flash the latest
Flash the HardSPL of your choice
Go to bootloader mode to confirm
DONE
Note: Have all you info available and files ready
When flashing SPL's, make sure your SD card is removed
Just went thru this just to get Security Unlocked because security unlock c/n be done with a 3.28 or 3.26 SPL and early on...HardSPL had to be done in wm6.0 and I had issues upgrading the SPL to 3.29 in wm6.0...that's why I say flash to 6.1 (say that twice)
you have bricked your device, for someone who claims to not be new, you should know better and flash hardspl before anything else.
if you want you can try this or just contact gsleon3
XtreMe_G said:
you have bricked your device, for someone who claims to not be new, you should know better and flash hardspl before anything else.
if you want you can try this or just contact gsleon3
Click to expand...
Click to collapse
actually ECLtech is walking me through it right now.
Hi
I get this problem too often and I dont know why and what I did do when I dont get it. This is the case.
Now I have flashed the g3 wizard with one of the wm6-manilla roms. I have succeded with this once so I have followed the guides with the unlocking and downgrading etc. Now I have downloaded a new cook and try to install it by starting the rom update utility wizard.
Problem is that the installation ALWAYS fails now. It starts, the device disconnects from activesynk, waits another 30 seconds then fails to restart the device so I get the dreadful Error 260 update error and the phone is dead. I remove the battery, restart the device and try again and my hair turns grey.
I figure I need to downgrade first so I try all the differens RUU's that are pointed out in the guides (CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe, ruu_prodigy_226102_22610105_022511_tmous_wwe_ship.exe, Xda_MiniS_LaunchROM_v154102.exe) but always the same problem.
What am I missing?
WinXP
AS4.5
IPL 2.26
SPL 2.26
Once downgraded and CID unlocked,a G3 device will remain CID unlocked forever,there's no need to downgrade everytime you flash a new rom.Just simply flash a new rom whenever you desire.So don't reflash Button's Rom 1.05 before every flash,its just required to flash once to get IPL/SPL 1.xx for CID unlocking,after which there's no need to reflash it again.
Error 260 is due to open port,so reboot your pc and Soft Reset the phone,hope it'll work fine.If you have reflashed Button's Rom 1.05 and downgraded,it wud be better if you perform the CID unlocking procedure again through lokiwiz02b or WST_4.2.2,after that upgrade to IPL/SPL 2.xx by either flashing T_mobile 2.26 or any official aku 2 rom,then upgrade to any wm6.1 rom.
You can even take out the battery and leave it for 30 minutes,after that put it back and try to flash.
Hmm.. now I have rebooted the pc and disconnected the battery for 30 mins. No luck. Still the same error.
There must be something I have missed. I have flashed with several roms before w/o any trouble.
I am connected to activesync as a guest on usb-cable.
Oh i didnt downgrade because it failed that too. So right now im on a wm6 manilla pretty good rom but the wifi's gone
Try flashing from bootloader:
* Hold down the camera button and then softrest without letting go of the camera button.
You should se a pretty tri color screen with IPL/SPL Information.
* Connect Wizard to PC using usb and wait for windows to detect the drivers if they are not already installed.
* Start your RUU and follow the steps.
Normally this error occurs when trying to flash under vista, if this is the case visit a friend who has XP and take some coffee
It gets worse im afraid.. and I am under XP.
Now the phone wont pass the t-mobile bootscreen. It gets stuck when showing the IPL/SPL information.
I fail to enter the bootloader. Hopefully im doing something wrong.
I have tried this:
1) Holding down cam-button and pressing soft-reset. The phone boots as normal but stucks at same place.
2) soft-reset and when sceen goes black, hold cambutton. Doing this makes the boot halt totaly and the screen remains black. Looks like it turns off cause the softreset wont work and I have to press the powerbutton to get life signs again.
How (exactly) do I get it into bootloader?
Evolution... i managed to do a hard-reset and got the phone to boot up again. So back to square one with not being able to use the ubs+ruu
hmm very strange.. in a desperate attemt to get into bootmode i held down the voice-button instead of the cam-button and then power-on. Not it worked! Mystic....
***
update! problem solved
In case anyone else reads this. I rebooted the pc for the 10th time, rebooted the phone at the same time and (a dramatic paus here) i pulled the usb-cable and placed it in another slot in the pc. And there it goes...
I dont work with computers... i work against them!
I'm new in the world of flashing cooked ROMs
and i need to do it but i can't
Everytime i try to Flash HARDSPL 3.xx, it stops at the percentage screen and gives me an error on my pc.
And i tried to flash the ROM directly, and same problem.
I'm getting nervous of this stupid mobile, please i need Help.
I read all posts on how to install everything but nothing completed to the end.
bebo833 said:
I'm new in the world of flashing cooked ROMs
and i need to do it but i can't
Everytime i try to Flash HARDSPL 3.xx, it stops at the percentage screen and gives me an error on my pc.
And i tried to flash the ROM directly, and same problem.
I'm getting nervous of this stupid mobile, please i need Help.
I read all posts on how to install everything but nothing completed to the end.
Click to expand...
Click to collapse
you should go here ...
I had a problem when I first did mine. at the tri-color screen my phone never said USB on it and my computer showed an unknown usb device. Here's what worked for me but remember you only need to do this the first time, Once you have HardSPL flashed your phone will work like normal.
after your phone gives you a warning that a program is going to reboot it. You get a tri-color screen. As soon as you see this screen hold the camera and power button and press the reset button, don't disconnect the usb cable.
In other words the program that causes your phone to reboot doesn't allow the usb to work properly but a manual reboot into the SPL using the camera/power button does. I have not tried the "Forced USB" version of HardSPL because this problem goes away once you get HardSPL installed.
This would be better posted in the HardSPL thread.
Flash an official stock ROM, then follow ALL the instructions in the link deepthroat gave you to the T.